Text

2009-09-DRAFT Jpms
	ML100880141
Person / Time
Site:	Cooper
Issue date:	09/21/2009
From:	; NRC Region 4
To:	; Nebraska Public Power District (NPPD)
References
	50-298/09-09
	Download: ML100880141 (149)
	v • d • e

Nebraska Public Power District SKL034-50-58 (36403) Cooper Nuclear Station Page 1 of 149 Job Performance Measure for Operations Revision: 00

Task No.: 283016S0101 Obtain and Interpret a GARDEL Periodic Report Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: CR / SIM

2. Appropriate Trainee level: RO / SRO

3. Evaluation Method: Perform

4. Performance Time: 10 minutes

5. NRC K/As 2.1.7 Imp. 3.7/4.4 Directions to Examiner:

1. This JPM evaluates the trainee

=s ability to Obtain and In terpret a Gardel Periodic Case. 2. If this JPM is performed on the Simulator, only the cues preceded by "#" should be given. 3. All blanks must be filled out with either initials or an "NP" for Anot performed

@; an explanation may also be written in the space, if desired, by the examiner.

Directions to Trainee:

When I tell you to begin, you are to Obtain and Ev aluate a Gardel Official Case by completing attachment 2 of 6.LOG.601. Be fore you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any me ters, gauges, recorders and controls you would be using. State the position of controls as you would have manipulat ed them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repositioning controls and observing instrumentation.

Nebraska Public Power District SKL034-50-58 (36403) Cooper Nuclear Station Page 2 of 149 Job Performance Measure for Operations Revision: 00

Task No.: 283016S0101 Obtain and Interpret a GARDEL Periodic Report General Conditions:

1. The Reactor is at approximately 100% power.

General

References:

1. Procedure 6.LOG.601 Da ily Surveillance Log.

General Tools and Equipment:

1. None Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1. 2. Critical steps denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

1. 100% of critical elements su ccessfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The Control Room Supervisor dire cts you to obtain a Gardel Periodic Case and verify that Thermal Limits are within Specification by completing Attachment 2 of 6.LOG.601. Inform the CRS when you have completed you review of the official case.

NOTE: Give the candidate Attachment 2 of 6.LOG.601 and tell the candidate to begin.

Nebraska Public Power District SKL034-50-58 (36403) Cooper Nuclear Station Page 3 of 149 Job Performance Measure for Operations Revision: 00

Task No.: 283016S0101 Obtain and Interpret a GARDEL Periodic Report Performance Checklist Standards Initials 1. Demand a Gardel Periodic Case The Operator demands and prints a Periodic Case.

CUE: Gardel Official Case prints.

CUE: Remove the periodic case from the printer and give the Candidate the attached Periodic Case

_______* 2. Scans the periodic case and records the highest value of MFLCPR. Value for the highest MFLCPR is recorded on .

_______* 3. Scans the periodic case and records the highest value of MFLPD.

Value for the highest MFLPD is recorded on .

_______ 4. Scans the periodic case and records the highest value of MAPRAT.

Value for the highest MAPRAT is recorded on .

_______ 5. Scans the periodic case and records reactor power. Reactor power is recorded on Attachment 2

_______ 6. Scans the periodic case and records lowest value of MCPR. Value for the lowest MCPR is recorded on .

_______ 7. Scans the periodic case and records lowest value of APRM GAF Value for the APRM GAF is recorded on .

8. Informs the CRS that MCPR is out of limits. CRS informed that MFLC PR value is greater than 1.

CUE: Acknowledge the report. Inform the candidate that the JPM is complete.

_______*

ATTACHMENT 1 Cooper Nuclear Station GARDEL Gardel: Periodic Report Today's Date Current Time

A C E B D F Thermal Power 2418.6 MWth 99.98%

APRM 100.1 100.

5100.7100.6100.3100.7 Elect. Power 827.1 MWel APRM GAF 1.006 1.0121.0171.0171.0141.017 Efficiency 34.18% APRM -%CTP

-0.57 -1.1 5-1.70-1.67-1.37-1.70 Coolant Flow 70.5 Mlb/hr95.95%

LPRM Status Normal APRM ave. 100.53 ADAPT ON TIP+LPRM The 4 most limiting bundles of the core MFLCPR PositionMCPR CPRLIMMFLPD PositionLHGR LHGRLIM MAPRATPosition APLHGR ALHLIM 1.004 19-32 1.467 1.370 0.800 31-44-04 10.718 13.397 0.887 19-28-05 9.228 10.399 1.004 15-32 1.471 1.370 0.798 35-44-04 10.689 13.397 0.887 21-32-05 9.102 10.257 1.003 23-38 1.532 1.370 0.798 11-38-04 10.686 13.397 0.882 25-34-04 9.289 10.535 1.002 37-24 1.541 1.370 0.794 15-42-04 10.637 13.397 0.805 35-44-04 8.159 10.138 Control Rod Withdrawal PCIUTL Position 19-28-04 02 06 10 14 18 22 26 30 34 38 42 46 50 Simulator Parameters CR withdrawal 4.81% 51 Ave. Xenon conc. 1593.85E12/cm3 Xenon symmetry -0.03% 47 Core press drop 18.04 psi Average void 47.08% 43 16 Total bypass flow 17.25%

K-effective 1.00159 39 Cycle burnup 2032 GWD/Mt Total pow peaking 2.461 35 Sup plate pres drop 13.19 psi 31 Heat Balance Parameters Feed water flow 9.49 Mlb/hr 27 16 12 16 Feed water temp. 363.66 F Absolute press 1009.78 psi 23 Inlet subcooling 31.33 Btu/lb CR drive temp. 100.00 F 19 CR drive flow 0.02Mlb/hr Cleanup inlet temp. 514.91 F 15 Cleanup system flow 0.11 Mlb/hr Ext. Recirc pump A 2.28 MW 11 16 Ext. Recirc pump B 2.29 MW Steam flow 9.51 Mlb/hr 07 Sup plate pres drop 15.03 psi 03

Nebraska Public Power District SKL034-50-58 (36403) Cooper Nuclear Station Page 5 of 149 Job Performance Measure for Operations Revision: 00 Task No.: 283016S0101 ATTACHMENT 2

Directions to Trainee:

When I tell you to begin, you are to obtain and interpret a Gardel Periodic Case. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any me ters, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repositioning controls and observing instrumentation.

General Conditions:

1. The Reactor is at approximately 100% power.

Initiating Cue(s):

The Control Room Supervisor direct s you to obtain a Gardel Period ic Case and to log Official case in 6.LOG.601 Attachment 2 to ve rify operation is within limits.

Inform the CRS when you have completed you review of the official case.

Nebraska Public Power District SKL034-50-57 (36402) Cooper Nuclear Station Page 6 of 149 Job Performance Measure for Operations Revision: 00 Task No.: 299012O0301 Determine Isolation Boundaries Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: CR / SIM

2. Appropriate Trainee level: RO / SRO

3. Evaluation Method: Perform 4. Performance Time: 15 minutes

5. NRC K/As 2.

1.24 2.8/3.1 Directions to Examiner:

4. This JPM evaluates the trainee's ability to determine appropriate mechanical isolation boundaries. 5. If this JPM is performed on the Simulator, only the cues preceded by "#"should be given. 6. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner.

Directions to Trainee:

When I tell you to begin, you are to use st ation documents to determine the minimum mechanical/piping boundaries required to isol ate the RHR 1A pump for removal. RHR 1A Motor has already been tagged and removed. Befo re you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any me ters, gauges, recorders and controls you would be using. State the position of controls as you would have manipulat ed them in order to complete the assigned task.

General Conditions:

N/A Nebraska Public Power District SKL034-50-57 (36402) Cooper Nuclear Station Page 7 of 149 Job Performance Measure for Operations Revision: 00 Task No.: 299012O0301 Determine Isolation Boundaries General

References:

1. Procedure 0.49

General Tools and Equipment:

1. Set of Mechanical Prints 2. Copy of 2040 Sheet 1

3. Copy of 2031 Sheet 2

Special Conditions, References, Tools, Equipment:

1. Simulator Setup: N/A. 2. Critical steps denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

1. 100% of critical elements su ccessfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The Control Room Supervisor directs you to determine the minimum mechanical/piping isolation boundaries required to isolate the RHR 1A pump for removal. RHR 1A Motor has already been tagged and removed. Find and highlight all valves required to be positioned to support this task.

Nebraska Public Power District SKL034-50-57 (36402) Cooper Nuclear Station Page 8 of 149 Job Performance Measure for Operations Revision: 00 Task No.: 299012O0301 Determine Isolation Boundaries Performance Checklist Standards Initials 9. May reference procedure 0.49. References procedure 0.49

_______ NOTE: Steps 2 thru 12 can be completed in any order 10. References BR 2040 Sheet 1 Finds BR 2040 Sheet 1

CUE: When the candidate successfully locates 2040 Sheet 1 Provide a copy for

the candidate to mark up.

_______* 11. Highlights RHR-MO-15A. RHR-MO-15A is highlighted.

_______* 12. Highlights RHR-MO-13A. RHR-MO-13A is highlighted.

_______* 13. Highlights RHR-98. RHR-98 is highlighted.

_______* 14. Highlights RHR-58. RHR-58 is highlighted.

_______* 15. Highlights RHR-11 RHR-11 is highlighted.

_______* 16. Highlights RHR drain path. RHR-35, RHR 36 and/or RHR 34 are highlighted.

_______ 17. References BR 2031 Sheet 2 to find REC Isolation valves.

Finds BR 2031 Sheet 2.

CUE: When the candidate successfully locates 2031 Sheet 2 Provide a copy for

the candidate to mark up.

_______*

Nebraska Public Power District SKL034-50-57 (36402) Cooper Nuclear Station Page 9 of 149 Job Performance Measure for Operations Revision: 00 Task No.: 299012O0301 Determine Isolation Boundaries Performance Checklist Standards Initials 18. Highlights REC-75. REC-75 is highlighted.

_______* 19. Highlights REC-76. REC-76 is highlighted.

_______* 20. Highlights REC Drain Path. REC-87, 397 and 83 are highlighted.

_______ 21. Informs the CRS that the boundaries are identified.

Gives the highlighted dra wings to the examiner.

CUE: Acknowledges rece ipt of the highlighted prints. This JPM is complete.

_______

Nebraska Public Power District SKL034-50-57 (36402) Cooper Nuclear Station Page 10 of 149 Job Performance Measure for Operations Revision: 00 ATTACHMENT 1

Directions to Trainee:

When I tell you to begin, you are to use st ation documents to determine the minimum mechanical/piping boundaries required to isol ate the RHR 1A pump for removal. RHR 1A Motor has already been tagged and removed. Befo re you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any meters, gauges, recorders and controls you would

be using. State the position of controls as you would have manipulat ed them in order to complete the assigned task.

General Conditions:

1. The plant is shutdown in a refueling outage. 2. RHR Loop A is not required to be operable.

Initiating Cue(s):

The Control Room Supervisor directs you to determine the minimum mechanical/piping isolation boundaries required to isolate the RHR 1A pump for removal. RHR 1A Motor has already been tagged and removed. Find and highlight all valves required to be positioned to support this task.

Nebraska Public Power District SKL034-30-52 (16532)

Cooper Nuclear Station Page 11 of 149 Job Performance Measure for Operations Revision 02

Task No.:

Task Title:

Radiation Protection Table Top Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Time Started: ____________ Time Finished: _____________

Additional Program Information: 1. Appropriate Performanc e Locations: CR, SIM, Class 2. Appropriate Trainee level: SO, RO, SRO

3. Evaluation Method:

Simulate Perform 4. Performance Time: 10 minutes

5. NRC K/A 2.3.1 (4.2)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to determine if certain work can be performed within the confines of the Code of F ederal Regulations and CNS procedures. 2. This JPM can be performed any place t he operator can access app ropriate procedures. 3. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in t he space if desired by the examiner.

Directions to Trainee:

When I tell you to begin, you are to determine whet her you can perform in-vessel work for which you are specially qualified. If you find you cannot perform the work state the reason you cannot. If you can perform the work state what authorization, if any is required prior to performing the work.

Before you start, I will state the general plant conditions, the Initiating Cues and answer any questions you may have.

General Conditions:

1. The plant is shutdown to perform in-vessel work. 2. Your on-site exposure is within 10%

of the average work group exposure.

General

References:

10CFR20 9.ALARA.1 Personnel dosimet ry and Occupational Radiation Exposure program.

Nebraska Public Power District SKL034-30-52 (16532)

Cooper Nuclear Station Page 12 of 149 Job Performance Measure for Operations Revision 02

Task No.:

Task Title:

Radiation Protection Table Top General Tools and Equipment:

1. None.

Special Conditions, References, Tools, Equipment:

1. Critical ch ecks denoted by "*". 2. Simulator cues denoted by "#".

Task Standards:

1. 100% of critical elements su ccessfully completed without error.

Initiating Cue(s):

You have unique skills to perform special in vessel work. Performance of the work is expected to result in a whole body dose of 500 mrem and a shallow dose to the skin of fingers of 7.5 Rem. Your Shift Manager directs you to determine based on your dose history, as provided whether you can perform this work.

Nebraska Public Power District SKL034-30-52 (16532)

Cooper Nuclear Station Page 13 of 149 Job Performance Measure for Operations Revision 02

Task No.:

Task Title:

Radiation Protection Table Top Performance Checklist Standards Initials 1. Refer to 9.ALARA.1 9.ALARA.1 referenced.

________

2. Pertinent personal Dose history is reviewed. Dose History is reviewed.

________ 3. Pertinent job dose projections for the job are

reviewed.

Dose projections are reviewed.

________ 4. Compares the job requirements to the amount

of dose that can be

received.

Job requirements are reviewed.

________ 5. Informs the SM that he cannot perform this job. SM informed.

CUE: Acknowledge the report and ask the operator what impediment exists for

performance.

________*

6. Informs the SM why he/she cannot perform the job.

SM informed that the r eason is that he/she is limited to 1000 mrem/year because his/her lifetime dose is in exce ss of the lifetime TEDE guideline and extensions to this limit cannot be granted.

CUE: Acknowledge the report and inform the operator that the JPM is complete.

________*

Nebraska Public Power District SKL034-30-52 (16532)

Cooper Nuclear Station Page 14 of 149 Job Performance Measure for Operations Revision 02

ATTACHMENT 1 Directions to Trainee:

When I tell you to begin, you are to determine whet her you can perform in-vessel work for which you are specially qualified. If you find you c annot perform the work st ate the reason you cannot and if you can perform the work st ate what authorization, if any is required prior to performing the work. Before you start, I will state the general plant conditions, the Initiating Cues and answer any questions you may have.

General Conditions:

1. The plant is shutdown to perform in-vessel work. 2. Your on-site exposure is within 10%

of the average work group exposure.

Initiating Cues:

You have unique skills to perform special in vessel work. Performance of the work is expected to result in a whole body dose of 500 mrem and a shallow dose to the skin of fingers of 7.5 Rem. Your Shift Manager directs you to determine based on your dose history, as provided whether you can perform this work.

Nebraska Public Power District SKL034-30-52 (16532)

Cooper Nuclear Station Page 15 of 149 Job Performance Measure for Operations Revision 02

Your Pertinent Statistics Your Age: 32 years Lifetime TEDE

35 Rem TEDE so far this year: 0.75 Rem Extremities SDE dose so far this year: 35 Rem NCR Form 116 has previously been signed.

Pertinent Job Dose Projections for the one individual performing this job Projected Whole Body Dose: 0.5 Rem Extremities SDE dose: 7.5 Rem

Nebraska Public Power District SKL034-50-56 (36401) Cooper Nuclear Station Page 16 of 149 Job Performance Measure for Operations Revision 00 Task No.: 259019P0401 Determine RPV Water Level Instrumentation Availability During LOCA Conditions Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: Classroom / Simulator 2. Appropriate Trainee Levels: RO/SRO/STE

3. Evaluation Method: Perform

4. Performance Time: 10 minutes

5. NRC K/A: 295028.EA2.03(CFR:

41.10 / 43.5 / 45.13)(3.7/3.9)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to determine RPV water level instrumentation availability during LOCA conditions. 2. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner. 3. Give the trainee his copy of the Directions to the Trainee (Attachment 1) when ready to start the JPM. 4. Brief the trainee and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to determine RPV water level instrumentation availability during LOCA conditions. Before y ou start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

During task performance, it is recommended that you limit your discussion/demonstration to the minimum required. The examiner may ask questi ons of you if necessa ry to understand your actions.

Nebraska Public Power District SKL034-50-56 (36401) Cooper Nuclear Station Page 17 of 149 Job Performance Measure for Operations Revision 00 Task No.: 259019P0401 Determine RPV Water Level Instrumentation Availability During LOCA Conditions General Conditions:

A LOCA has occurr ed with the following stable plant conditions:

- Narrow range RPV water level + 0" (indicated)

- Shutdown Range + 0" (indicated)

- Steam Nozzle Range + 0" (indicated)

- Wide range RPV water level - 140" (indicated)

- Fuel zone RPV water level - 145 " (indicated)

- RPV pressure 55 psig (6 SRVs open)

- Drywell pressure 53.1 psig (drywell spray unavailable) - Drywell temp 330 °F (All PC-TI-505's and 510's)

General

References:

1. Procedure 5.8

2. EOP/SAP Graphs

General Tools and Equipment:

1. EOP/SAP Graphs

Special Conditions, References, Tools, Equipment:

1. Critical checks denoted by "*".

Nebraska Public Power District SKL034-50-56 (36401) Cooper Nuclear Station Page 18 of 149 Job Performance Measure for Operations Revision 00 Task No.: 259019P0401 Determine RPV Water Level Instrumentation Availability During LOCA Conditions Task Standards:

1. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

You are to determine RPV water level instrumentation availability during LOCA conditions.

Complete the table below with the status of RPV level instruments return this Attachment to the examiner when you have completed this task.

Nebraska Public Power District SKL034-50-56 (36401) Cooper Nuclear Station Page 19 of 149 Job Performance Measure for Operations Revision 00 Task No.: 259019P0401 Determine RPV Water Level Instrumentation Availability During LOCA Conditions Performance Checklist Standards Initials NOTE: Steps may be performed concurrently or in any order

1. Refer to EOP/SAG Graphs. The operator refers to EOP/SAG Graphs.

_______ 2. Refer to EOP/SAG Graphs. The operator refers to EOP/SAG Graphs. Determines Narrow range RPV water level is Not

Available

_______* 3. Refer to EOP/SAG Graphs. The operator refers to EOP/SAG Graphs. Determines Steam Nozzle Range RPV water level

is Not Available

_______* 4. Refer to EOP/SAG Graphs. The operator refers to EOP/SAG Graphs. Determines Shutdown Range RPV water level is Not Available

_______* 5. Refer to EOP/SAG Graphs. The operator refers to EOP/SAG Graphs. Determines Wide range RPV water level is Not Available _______* 6. Refer to EOP/SAG Graphs. The operator refers to EOP/SAG Graphs. Determines Fuel Zone RPV water level is Available for Trending

_______* 7. Turns in completed paperwork.

Returns completed Attachment 1 to evaluator

. _______

Nebraska Public Power District SKL034-50-56 (36401) Cooper Nuclear Station Page 20 of 149 Job Performance Measure for Operations Revision 00 ATTACHMENT 1 Directions to Trainee:

You are to determine RPV water level instrument ation availability during LOCA conditions.

Complete the table below with the status of RPV level instrument s and return this attachment to the examiner when you have completed this task.

General Conditions:

A LOCA has occurr ed with the following stable plant conditions:

- Narrow range RPV water level + 0" (indicated)

- Shutdown Range RPV water level + 0" (indicated) - Steam Nozzle Range RPV water level + 0" (indicated) - Wide range RPV water level - 140" (indicated)

- Fuel zone RPV water level - 145 " (indicated)

- RPV pressure 55 psig (6 SRVs open)

- Drywell pressure 53.1 psig (drywell spray unavailable)

- Drywell temp 330 °F (All PC-TI-505's and 510's)

What is the status of RPV water level instruments?

Level Instrument AFT = Available for Trending, NA = Not Available Narrow range RPV water level Shutdown Range RPV water level Steam Nozzle Range RPV water level Wide range RPV water level Fuel zone RPV water level

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 21 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Time Started: ____________ Time Finished: _____________

Additional Program Information:

1. Appropriate Performance Locations: SIM / CR

2. Appropriate Trainee Level: SRO / STE

3. Evaluation Method: Perform

4. Performance Time: 25 minutes

5. NRC K/A 2.4.28 (2.3/3.3)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to perform the required actions for a Security Emergency. 2. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner. 3. Give the trainee his copy of the Directions to the Trainee (Attachment 1) when ready to start the JPM. 4. Brief the trainee, place the Simula tor in RUN, and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to respond to a Security Emergency as appropriate to the provided conditions. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

When simulating, physically point to any meters , gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task. ALL PLANT ANNOUNCEMENTS WILL BE SIMULATED!

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 22 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency General Conditions:

1. The plant is operating at 30% power.

2. The Shift Manager has delegated y ou to direct the plant response. 3. The board operators are available ON LY to support control room actions. 4. You must personally perform any comm unications required for this situation. 5. The Shift Manager will perform a ll Emergency Director required actions.

General

References:

1. Emergency Procedure 5.5SECURITY

General Tools and Equipment:

1. Site communication System.

2. Emergency Telephone number book.

Special Conditions, References, Tools, Equipment:

1. Critical checks denoted by "*".

Task Standards:

1. 100% of critical elements succe ssfully completed without error.

2. 100% of safety and radiological work practices.

Initiating Cue(s):

At 9:35 p.m. you are informed by the Operations Manag er that armed intruders have been seen in the protected area. The intr uders last known location was the 903 corridor outside the door to the reactor building. The intruders are carrying automatic rifles, pistols and grenades.

You are to perform the required control room actions for this situation until directed to stop by the evaluator.

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 23 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency Performance Checklist Standards Initials 1. Obtain Procedure 5.5SECURITY.

Current revision of 5.5SECURITY obtained. (Note: May be given if the operator goes to procedure rack or lock box in simulator.)

________

2. Contact the Security Shift Supervisor to

confirm threat.

Security Shift Supervisor contacted and asked to confirm the threat.

CUE: As the Security Shift Supervisor, indicate that the intruders posses explosive devices and automatic weapons.

An actual Security Threat exists with high potential for significant

structural damage and personnel injury. Security is in a "Code Red"

CUE: Security has just made the following plant announcement, "All Station Personnel, Imminent Security Threat exists, seek shelter inside the nearest

building. Code Red".

________ 3. Determines that an Actual Threat exists and enters 5.5Security

.

Enters Attachment 2

CUE: If asked, a credible insider threat DOES NOT exist. #CUE: The SM directs you to DIRECT actions per Attachment 2 and he/she will complete remaining actions in Section 4. ________*

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 24 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency Performance Checklist Standards Initials 4. Directs the reactor be scrammed.

RO directed to scram the reactor.

CUE: As the RO, acknowledge the order and report that the reactor is scrammed. All control rods are fully inserted. RPV water level and pressure are stable. No EOP entry conditions were met during the

scram. ________* 5. Directs level be maintained high is level

band using RCIC BOP/RO/WCO directed to maintain level high in the band using RCIC per 2.2.67.1.

CUE: As the BOP/WCO/RO, acknowledge the order and report that RCIC is

running and level is being controlled

+20"to +45" using RCIC.

________* 6. Directs Reactor Cooldown. RO/BOP/WCO directed to cooldown reactor not to exceed 90 degrees per hour.

CUE: As the BOP/WCO/RO, acknowledge the order and report that Reactor pressure is being lowered to 500 psig using Turbine Bypass Valves (or as directed in order by SRO).

________* 7. Directs maximizing CRD for injection.

RO/BOP/WCO directed to maximize CRD injection per 5.8.4.

CUE: As the BOP/WCO/RO, acknowledge the order and report that you will review procedure and perform when

RB Station Operator is available.

________

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 25 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency Performance Checklist Standards Initials 8. Directs the BOP to ensure that BF-C-1A, EMERGE BSTR FAN is

running. BOP/WCO directed to ens ure that BF-C-1A, EMERGE BSTR FAN is running.

CUE: As the BOP/WCO, acknowledge the order and report that BF-C-1A, EMERG BSTR FAN is running.

________* 9. Directs rapid isolation of RWCU. RO/BOP/WCO directed to remove RWCU from service. # CUE: As the BOP/WCO/RO, acknowledge the order and report that RWCU has

been removed from service and

isolated. You are following up per 2.2.66. ________* 10. Directs the BOP to start and run unloaded

both DGs.

BOP/WCO directed to start and run unloaded both DGs.

CUE: As the BOP/WCO acknowledge the order. (If prestart checks are waived, report that both DGs are running

unloaded.)

________*

NOTE: Controls for the fire pumps do not exist in the simulator.

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 26 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency Performance Checklist Standards Initials 11. Directs or Starts Electric Fire pump 1E or 1D.

Directs the BOP/WCO to st art the 1E or 1D Fire Pump or places the 1E or 1D fire pump control switch to start.

CUE: If BOP/WCO directed, then acknowledge the order as the BOP

and report that the diesel or motor

driven Fire Pump is running. (If the

CRS starts the pump the RED light is ON and the GREEN light is OFF for

the pump started.)

________

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 27 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency Performance Checklist Standards Initials 12. Directs Station Operators/UT Fire Brigade to obtain fire

fighting gear and report

to the Control Room.

Station Operators directed to obtain fire fighting gear and to report to the Control Room.

CUE: Indicate that the Radwaste Station Operator and UT Fire Brigade personnel have reported to the

Control Room.

CUE: The Turbine Building operator contacts the Control Room and reports that he is unable to get to the Control Room at this time. He is just

outside the #1 DG room and the 903

area just outside the doors to the control building is blocked by the

armed intruders. The intruders are currently unaware of his presence.

The Station Operator requests direction from you.

CUE: The Reactor Building operator contacts the Control Room and

reports that he is un able to get out of the Reactor Building at this time. He

is in the SE Quad (859' elevation).

The intruders are currently unaware of his presence. The Station

Operator requests direction from you. ________

13. Directs the Duty Chem/RP Tech to

report to the control

room. The Duty Chem/RP Tech is called to the control room.

CUE: The Duty Chem/RP Tech reports to the control room.

________*

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 28 of 149 Job Performance Measure for Operations Revision 07 Task No. 344050O0503 Security Emergency Performance Checklist Standards Initials 14. Directs the TB Station Operator to card into the DG room and RB

Station Operator told to

stay in Vital Area. TB Station Operator directed to enter the DG room and RB Station Operator told to stay in Vital Area.

CUE: TB operator acknowledges the order and reports that he has entered the DG room and RB Station Operator is remaining in current location (or as

directed).

________*

PROVIDE THE FOLLOWING CUE: Annunciators 9-3-3/G-5 "ASD Room Door Open" and 9-3-3/F-5 "ASD Switch Position Abnormal" have just alarmed. 15. Responds to ASD Abnormal indications Directs RB Station O perator to open EE-DSC-125ASD or EE-DSC-125B.

CUE: If asked as RB Station Operator, report that you can get to EE-DSC-

125ASD.

CUE: If asked if anyone has been dispatched to CB-903', report that no operator is currently in that area.

CUE: If the SRO directs and operator to CB-903 to open EE-DSC-125B, report that you have opened EE-DSC-125B

CUE: As RB Station Operator dispatched to open disconnect, report that EE-

DSC-125ASD is open.

CUE: The JPM is complete.

________*

Nebraska Public Power District SKL034-30-26 (6253) Cooper Nuclear Station Page 29 of 149 Job Performance Measure for Operations Revision 07

ATTACHMENT 1 Directions to Trainee:

When I tell you to begin, you are to respond to a Security Emergency as appropriate to the provided conditions. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task. ALL PLANT ANNOUNCEMENTS WILL BE SIMULATED!

General Conditions:

1. The plant is operating at 30% power. 2. The Shift Manager has delegated y ou to direct the plant response. 3. The board operators are available ON LY to support control room actions. 4. You must personally perform any comm unications required for this situation. 5. The Shift Manager will perform a ll Emergency Director required actions.

Initiating Cue(s):

At 9:35 p.m. you are informed by the Security Shift Superviso r that armed intruders have been seen in the protected area. T he intruders last known location was the 903 corridor outside the door to the reactor building. The intruders ar e carrying automatic rifles, pistols and grenades.

You are to perform the required control room actions for this situation until directed to stop by the evaluator.

Nebraska Public Power District SKL034-20-114 (29981) Cooper Nuclear Station Page 30 of 149 Job Performance Measure for Operations Revision 01 Task No. 341033W0303 Determine Shift Staffing R equirements for Mode Change Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Time Started: ____________ Time Finished: _____________

Additional Program Information:

6. Appropriate Performance Locations: SIM / CR

7. Appropriate Trainee Level: SRO

8. Evaluation Method: Perform

9. Performance Time: N/A

10. NRC K/A 2.1.4 (3.4)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to determine shift staffing requirements for a mode change. 2. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner. 3. Give the trainee his copy of the Directions to the Trainee (Attachment 1) when ready to start the JPM. 4. Brief the trainee and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to evaluate t he staff available and determine if a change in Modes can occur without incurring an LCO condition. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

Nebraska Public Power District SKL034-20-114 (29981) Cooper Nuclear Station Page 31 of 149 Job Performance Measure for Operations Revision 01 Task No. 341033W0303 Determine Shift Staffing R equirements for Mode Change General Conditions:

1. The plant conditions are as follows: Reactor Pressure is 0 psig Coolant temperature is 200ºF Mode Switch is in Shutdown

2. Your Shift complement is comprised of: One SRO (you) Two ROs Three Non-Licensed Nuclear Plant Operators One RP/Chem Tech General

References:

1. Conduct of Operat ions Procedure 2.0.3 General Tools and Equipment:

1. None Special Conditions, References, Tools, Equipment:

1. Critical checks denoted by "*".

Task Standards:

3. 100% of critical elements succe ssfully completed without error.

4. 100% of safety and radiological work practices.

Initiating Cue(s):

During your shift Reactor Coolant temperature is expected to rise to 215ºF as a result of Shutdown Cooling being removed from service. As the Senior Licensed person on your shift, you are to determine two things; 1. Do you have sufficient staff now and 2. will you have sufficient staff to allow you to raise Coolant Temperature to 215º F during your shift. If not determine how many additional staff types are needed and document your findings on .

Nebraska Public Power District SKL034-20-114 (29981) Cooper Nuclear Station Page 32 of 149 Job Performance Measure for Operations Revision 01 Task No. 341033W0303 Determine Shift Staffing R equirements for Mode Change

Nebraska Public Power District SKL034-20-114 (29981) Cooper Nuclear Station Page 33 of 149 Job Performance Measure for Operations Revision 01 Task No. 341033W0303 Determine Shift Staffing R equirements for Mode Change Performance Checklist Standards Initials 16. Obtain Procedure 2.0.3. Current revision of 2.0.3 obtained. ________ 17. Determine section of Procedure

2.0.3. The SRO turns to Section 10, Control Room and Shift Staffing Requirements. ________ 18. Determines the current mode.

The SRO may use Tech Specs to confirm that the Unit is in MODE 4. ________ 19. Determines the mode to be entered when temperature rises to

215ºF The SRO may use Tech Specs to confirm that the Unit will be entering M ode 3 within the shift. ________* 20. Determines that the current shift staff is

adequate until the

mode change. Your Shift complement is comprised of: One SRO (you) Two ROs Three Non-Licensed Nuclear Plant Operators One RP/Chem Tech ________* 21. Determines which staff types are required.

For Mode 3 the SRO determines that the following staff types are needed: Two SRO (so there is a SM and a CRS) Three RO (RO, BOP, WCO) Three Non-Licensed Nuclear Plant Operators One STE One RP/Chem Tech ________* 22. Writes the needed Staff on Attachment 1.

The SRO writes the addi tional needed staff on . One SRO (so there is a SM and a CRS) One RO (RO, BOP, WCO) One STE ________*

Nebraska Public Power District SKL034-20-114 (29981) Cooper Nuclear Station Page 34 of 149 Job Performance Measure for Operations Revision 01 Task No. 341033W0303 Determine Shift Staffing R equirements for Mode Change Performance Checklist Standards Initials 23. Turns in completed paperwork.

Returns completed Attachment 1 to evaluator

. _______

Nebraska Public Power District SKL034-20-114 (29981) Cooper Nuclear Station Page 35 of 149 Job Performance Measure for Operations Revision 01

ATTACHMENT 1 Directions to Trainee:

When I tell you to begin, you are to evaluate t he staff available and determine if a change in Modes can occur without incurring an LCO condition.

Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

General Conditions:

1. The plant conditions are as follows: Reactor Pressure is 0 psig Coolant temperature is 200ºF Mode Switch is in Shutdown

2. Your Shift complement is comprised of: One SRO (you) Two ROs Three Non-Licensed Nuclear Plant Operators One RP/Chem Tech Initiating Cue(s):

During your shift Reactor Coolant temperature is expected to rise to 215ºF as a result of Shutdown Cooling being removed from service. As the Senior Licensed person on your shift, you are to determine two things; 1. Do you have sufficient staff now and 2. Will you have sufficient staff to allow you to raise Coolant Temperature to 215º F during your shift? If not determine how many additional staff types are needed and document your findings on .

Current Staff:

Adequate in cu rrent mode Inadequate in current mode (Check one)

Additional needed staff:

________________________

__________________

___________________________

Staff required

at 215ºF:

Cu rrent staff adequate

Additional staff needed. (Check one)

Nebraska Public Power District SKL034-20-114 (29981) Cooper Nuclear Station Page 36 of 149 Job Performance Measure for Operations Revision 01

Additional needed staff:

________________________

_________________________

____________________

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 37 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: Simulator Only

2. Appropriate Trainee Level: RO / SRO

3. Evaluation Method:

Perform in Simulator Only. 4. Performance Time: 18 minutes

5. NRC K/A 202001 K1.06 3.6/3.6

Directions to Examiner:

1. This JPM evaluates the trainee's ability to perform the daily Jet Pump and Recirc Pump Flow Check of the Daily Te ch Specs Surveillance Log.

2. Provide the Reactor Recirc and Jet Pump values to the candidate; do not allow them to take the readings form the simulator. 3. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner. 4. Give the trainee his copy of the Directions to the Trainee (Attachment 1) when ready to start the JPM. 5. Brief the trainee, place the Simula tor in RUN, and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to perform the activities associated with daily Jet Pump AND Recirc Pump Flow Check. Before you start, I will state the general plant conditions, the initiating cues and answer any questions you may have.

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

General Conditions:

1. The plant is operating at rated power with DEH in Mode 4. 2. Both Reactor Recirculation pumps are operating with pump flows balanced. 3. Data is provided for the readings to be taken.

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 38 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

General

References:

1. Procedure 6.LOG.601

General Tools and Equipment:

1. Calculator.

2. Jet pump operability curves.

Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1.

2. Critical checks denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

1. 100% of critical elements su ccessfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

RO. The Control Room Supervisor directs you to per form the daily Jet Pump (6.LOG.601 Attachment 12) and Recirc Pump Flow Check (6.LOG.601 A ttachment 13) as part of the routine shift activities. Notify the CRS when the task is complete.

SRO. Perform the Control Room Super visor's review of the daily Jet Pump (6.LOG.601 Attachment 12) and Recirc Pump Flow Check (6.LOG.601 A ttachment 13) as part of the routine shift activities to ensure that it has been performe d correctly. Notify the SM when the task is complete.

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 39 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

Performance Checklist Standards Initials NOTE: 1. This is the RO Section.

2. Steps 1 - 5 may be in any order. 1. Record indicated core flow (10 6 lb/hr) Record Core flow from Recorder NBI-FRDPR-95 (Green Pen) (+/- 2).

CUE: Core Flow = 62

_______* 2. Record RR pump flow (10 3 gpm) Record RR pump flow, from RR-FR-163 for Pumps A & B (+/- 2).

CUE: Pump A = 38.5; Pump B = 38.5

_______* 3. Record RRMG Set speed Record RRMG Set speed from the following (+/- 2):

a. RRFC-SI-1A for RRMG A

b. RRFC-SI-1B for RRMG B

CUE: RRMG A = 79; RRMG B = 80.

_______*

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 40 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

Performance Checklist Standards Initials 4. Record Jet Pump Flow Record Jet Pump Flow from the following (+/- 2):

a. NBI-FI-92A for LOOP A

b. NBI-FI-92B for LOOP B

CUE: LOOP A = 31; LOOP B = 31

_______* 5. Record Jet Pump Differential Pressure Record differential pressures from individual jet pump instruments NBI-FI-78A through NBI-FI-78Z on Panel 9-38 in control room (+/- 2).

CUE: 1 = 31 11 = 32 2 = 32 12 = 30 3 = 31 13 = 20 4 = 31 14 = 32 5 = 36 15 = 34 6 = 34 16 = 35 7 = 33 17 = 32 8 = 32 18 = 31 9 = 33 19 = 33 10 = 33 20 = 32

Note G, H, I, O, P & Q are not used. _______* 6. Record Loop B and Loop A Average Add JP #1 through 10 and divide by 10 for LOOP B, then add JP #11 through 20 and divide by 10 for LOOP A (+/- 2).

CUE: Average 32.6 for LOOP B and 31.1 for LOOP A. _______*

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 41 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

Performance Checklist Standards Initials NOTE: Curves are contained in the binder labeled "Cooper Nuclear Station Jet Pump Operability Graphs and Instability Noise Level Data".

7. Verify RR pump flow and RRMG set speed

within limits.

Check 1 Determine that the values recorded in Items B and C are within t he limits of the curve (SAT checked).

_______* 8. Verify JP flow and RRMG set speed

within limits.

Check 2 Determine that the values recorded in Items C and D are within or outside the limits of the curve (SAT checked).

_______

NOTE: Jet Pump 13 is outside the Operability Graphs. The candidate should determine that it falls outside the limit.

9. Jet Pump p differs by < 20% from established patterns.

Check 3 Determine that Jet Pump p differs by 20% from established patterns for (UNSAT checked for Loop A).

_______* 10. Verify check 1 and 2 SAT or check 3 SAT.

Verify check 1 and check 2 SAT or check 3 is SAT (Check 3 is SAT).

_______* 11. Verify operation is not in Stability Exclusion Region of Power to

Flow Map.

Determines operation is outside Stability Exclusion Region of Power to Flow Map using core flow value recorded in Item A on pr evious page and 2.1.10 Power to Flow Map.

_______*

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 42 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

Performance Checklist Standards Initials 12. Verify loop flow mismatch is within limit when at < 51.45

x10 6 lbs/hr core flow.

Determine Step is N/A.

_______ 13. Verify loop flow mismatch is within limits when 51.45x10 6 lbs/hr core flow.

Determine Item D values (previous page of 6.LOG.601) for Loop A and Loop B flow mismatch

is 3.67x10 6 lbs/hr (SAT entered into block).

_______* 14. Verify Recirc Pump operating or RHR Pump operating in

SDC. Determine Step is N/A.

_______ 15. Inform the CRS that the task is complete.

Inform Control Room Super visor that the daily Jet Pump and Recirc Pump Flow Check is Complete and Jet Pump 13 d/p is low out of spec.

CUE: The CRS Acknowledges the report.

_______

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 43 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

SRO Section Performance Checklist Standards Initials NOTE: 1. SRO Section

2. Declares Jet Pump 13 inop.

1. Reviews Attachment 12 "Jet Pump Operability" Items. Reviews Attachment 12 "Jet Pump Operability" Items A, B, C and D. Notes that all have been filled out correctly.

_______

2. Reviews Attachment 12 "Jet Pump Operability" Checks 1, 2 and 3. Reviews Attachment 12 "Jet Pump Operability" Items 1, 2, and 3. Notes that Check 3 should be checked Unsat and denotes it.

_______* 3. Reviews Attachment 13 "RECIRC Pump

Flow Checks" Checks Reviews Attachment 13 "RECIRC Pump Flow Checks", NBI-FRDPR-95 is outside of the Exclusion Region. Checks that it is marked SAT correctly.

_______* 4. Reviews Attachment 13 "RECIRC Pump Flow Checks" Checks Reviews Attachment 13 "RECIRC Pump Flow Checks", NBI-FI-92A/B Mismatch should be N/A'ed for this flow.

_______ 5. Reviews Attachment 13 "RECIRC Pump

Flow Checks" Checks Reviews Attachment 13 "RECIRC Pump Flow Checks", NBI-FI-92A/B Mismatch should be marked SAT. Checks that it is marked SAT correctly.

_______* 6. Reviews Attachment 13 "RECIRC Pump Flow Checks" Checks Reviews Attachment 13 "RECIRC Pump Flow Checks", Recirc Pump operating or RHR Pump operating in SDC is marked N/A.

_______

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 44 of 149 Job Performance Measure for Operations Revision 01

Task No.: 202012O0201 PERFORM JET PUMP OPERABILI TY CHECK (RO or SRO)

Performance Checklist Standards Initials 7. Notifies Reactor Engineer Notifies the Reactor Engine er that Jet Pump 13 d/p is low out of spec.

CUE: As reactor engineer respond to the report and tell the CRS that it wa s not low last time the surveillance was run.

_______ 8. Notifies the Shift Manager Contacts the Shift Manager and tells him that Jet Pump 13 is low out of spec and that was not that way last surveillance.

CUE: Respond as the Shift Manager and tell the CRS that the JPM is completed.

_______

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 45 of 149 Job Performance Measure for Operations Revision 01 ATTACHMENT 1 Directions to Trainee:

When I tell you to begin, you are to perform the daily Jet Pump and Recirc Pump Flow Check. Before you start, I will state the general plant conditions, the initiating cues and answer any questions you may have.

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

General Conditions:

1. The plant is operating at ra ted power with DEH in Mode 4. 2. Both Reactor Recirculation pumps are operating with pump flows balanced.

Initiating Cues:

RO.

The Control Room Supervisor directs you to perform the daily Jet Pump (6.LOG.601 Attachment 12) and Recirc Pump Flow Check (6.LOG.601 Attachment

13) as part of the routine shift activities. Notify the CRS when the task is complete.

Jet Pumps 1 = 31 11 = 32 2 = 32 12 = 30 3 = 31 13 = 20 4 = 31 14 = 32 5 = 36 15 = 34 6 = 34 16 = 35 7 = 33 17 = 32 8 = 32 18 = 31 9 = 33 19 = 33 10 = 33 20 = 32 SRO. Perform the control room supervi sor's review of the daily je t pump (6.log.601 attachment 12) and recirc pump flow check (6.log.601 attachment 13) as part of the routi ne shift activities to ensure that it has been performed correctly.

Notify the Shift Manager when the task is complete.

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 46 of 149 Job Performance Measure for Operations Revision 01 ATTACHMENT 12 JET PUMP OPERABILITY RO SECTION ATTACHMENT 12 JET PUMP OPERABILITY NOTE - If in single loop operation, mark idle loop N/A.

JET PUMP P (%) ITEMS LOOP A LOOP B JP # LOOP B JP # LOOP A A Core Flow (10 6 lb/hr) NBI-FRDPR-95 1 11 B RR Pump Flow (10 3 gpm) RR-FR-163 2 12 C RRMG Set Speed (%) RRFC-SI-1A/B 3 13 D JP Flow (10 6 lb/hr) NBI-FI-92A/B 4 14 5 15 6 16 7 17 8 18 9 19 10 20 LOOP B Avg LOOP A Avg CHECKS SATUNSA T OPERABILIT Y LIMIT APPLICABL E MODE ATT. 21 NOTE Loop A: 1 Item B and C values within curve limits (a) Loop B: Loop A: 2 Item C and D values within curve limits (a) Loop B: Loop A: 3 Jet Pump P differs by 20% from established patterns (a, c) Loop B: SAT 1 (b), 2 (b) 50 Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 47 of 149 Job Performance Measure for Operations Revision 01 Loop A: Checks 1 and 2 SAT, or Check 3 SAT Loop B: SAT (a) Refer to Jet Pump Operability Curves maintained in Control Room. (b) Required to be performed within 24 hours2.777778e-4 days 0.00667 hours 3.968254e-5 weeks 9.132e-6 months a fter > 25% RTP and required to be performed within 4 hours4.62963e-5 days 0.00111 hours 6.613757e-6 weeks 1.522e-6 months after associated reci rculation loop is in service. (c) If any Jet Pump P vs. established pattern is not within curve limits, immediately notify Reactor Engineering.

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 48 of 149 Job Performance Measure for Operations Revision 01 Attachment 13 RECIRC PUMP FLOW CHECKS RO Section ATTACHMENT 13 RECIRC PUMP FLOW CHECKS CHECKS 0700-1000 SAT/UNSAT 1900-2200 SAT/UNSAT OPERABILITY LIMIT APPLICABLE MODES ATT. 21 NOTES Core Flow, NBI-DPR/FR-95, value is not in Stability Exclusion Region of Power to Flow Map (a) MCO SAT 1, 2 49 JP Flow, NBI-FI-92A/B, values for Loop A and Loop B flow mis-match is 7.35x10 6 lbs/hr at

< 51.45x10 6 lbs/hr Rated Core Flow (b) (d) MCO SAT 1 (c), 2 (c) 48, 127 JP Flow, NBI-FI-92A/B, values for Loop A and Loop B flow mis-match is 3.67x10 6 lbs/hr at 51.45x10 6 lbs/hr Rated Core Flow (b) (d) MCO SAT 1 (c), 2 (c) 48, 127 (a) Refer to power to flow map in Procedure 2.1.10. (b) Per Technical Specification and TRM Bases, a recirculation loop is considered not in operation when the mis-match between total jet pump flows of the two loops is greater than required limits. The loop with the lowe r flow must be considered not in operation. (c) Required to be performed within 24 hours2.777778e-4 days 0.00667 hours 3.968254e-5 weeks 9.132e-6 months after both recirculation loops are in service. (d) If a flow mismatch results in one loop c onsidered not in operation, contact FRED to manually insert single loop oper ation limits into GARDEL. CHECK 0700-1000 READING () (e) 1900-2200 READING () (e) OPERABILITY LIMIT APPLICABLE MODES ATT. 21 NOTES Verify Recirc Pump operating or RHR Pump operating in SDC RR Pump or SDC in Operation 3 (when Reactor Pressure is less than SDC Pressure Permissive) (f) 66 (e) indicates at least one RR pump or SDC Subsystem is in service. (f) Required to be met within 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months after reac tor steam dome pressure is less than the shutdown cooling permissive pressure.

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 49 of 149 Job Performance Measure for Operations Revision 01 Attachment 12 JET PUMP OPERABILITY SRO Section ATTACHMENT 12 JET PUMP OPERABILITY NOTE - If in single loop operation, mark idle loop N/A.

JET PUMP P (%) ITEMS LOOP A LOOP B JP # LOOP B JP # LOOP A A Core Flow (10 6 lb/hr) NBI-DPR/FR-95 62 1 31 11 32 B RR Pump Flow (10 3 gpm) RR-FR-163 38.5 38.5 2 32 12 30 C RRMG Set Speed (%) RRFC-SI-1A/B 79 80 3 31 13 20 D JP Flow (10 6 lb/hr) NBI-FI-92A/B 31 31 4 31 14 32 5 36 15 34 6 34 16 35 7 33 17 32 8 32 18 31 9 33 19 33 10 33 20 32 LOOP B Avg 32.6 LOOP A Avg 31.1 CHECKS SATUNSA T OPERABILIT Y LIMIT APPLICABL E MODE ATT. 21 NOTE Loop A: 1 Item B and C values within curve limits (a) Loop B: Loop A: 2 Item C and D values within curve limits (a) Loop B: Loop A: 3 Jet Pump P differs by 20% from established patterns (a, c) Loop B: SAT 1 (b), 2 (b) 50 Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 50 of 149 Job Performance Measure for Operations Revision 01 Loop A: Checks 1 and 2 SAT, or Check 3 SAT Loop B: SAT (a) Refer to Jet Pump Operability Curves maintained in Control Room. (b) Required to be performed within 24 hours2.777778e-4 days 0.00667 hours 3.968254e-5 weeks 9.132e-6 months a fter > 25% RTP and required to be performed within 4 hours4.62963e-5 days 0.00111 hours 6.613757e-6 weeks 1.522e-6 months after associated reci rculation loop is in service. (c) If any Jet Pump P vs. established pattern is not within curve limits, immediately notify Reactor Engineering.

Nebraska Public Power District SKL034-20-113 (29979) Cooper Nuclear Station Page 51 of 149 Job Performance Measure for Operations Revision 01 Attachment 13 RECIRC PUMP FLOW CHECKS SRO Section ATTACHMENT 13 RECIRC PUMP FLOW CHECKS CHECKS 0700-1000 SAT/UNSAT 1900-2200 SAT/UNSAT OPERABILITY LIMIT APPLICABLE MODES ATT. 21 NOTES Core Flow, NBI-DPR/FR-95, value is not in Stability Exclusion Region of Power to Flow Map (a) SAT MCO SAT 1, 2 49 JP Flow, NBI-FI-92A/B, values for Loop A and Loop B flow mis-match is 7.35x10 6 lbs/hr at

< 51.45x10 6 lbs/hr Rated Core Flow (b) (d) N/A MCO SAT 1 (c), 2 (c) 48, 127 JP Flow, NBI-FI-92A/B, values for Loop A and Loop B flow mis-match is 3.67x10 6 lbs/hr at 51.45x10 6 lbs/hr Rated Core Flow (b) (d) SAT MCO SAT 1 (c), 2 (c) 48, 127(a) Refer to power to flow map in Procedure 2.1.10. (b) Per Technical Specification and TRM Bases, a recirculation loop is considered not in operation when the mis-match between total jet pum p flows of the two loops is greater than required limits. The loop with the lower fl ow must be considered not in operation. (c) Required to be performed within 24 hours2.777778e-4 days 0.00667 hours 3.968254e-5 weeks 9.132e-6 months after both recirculation loops are in service. (d) If a flow mismatch results in one loop c onsidered not in operation, contact FRED to manually insert single loop oper ation limits into GARDEL. CHECK 0700-1000 READING () (e) 1900-2200 READING () (e) OPERABILITY LIMIT APPLICABLE MODES ATT. 21 NOTES Verify Recirc Pump operating or RHR Pump operating in SDC N/A N/A RR Pump or SDC in Operation 3 (when Reactor Pressure is less than SDC Pressure Permissive) (f) 66 (e) indicates at least one RR pump or SDC Subsystem is in service. (f) Required to be met within 2 hours2.314815e-5 days 5.555556e-4 hours 3.306878e-6 weeks 7.61e-7 months after reac tor steam dome pressure is less than the shutdown cooling permissive pressure.

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 52 of 149 Job Performance Measure for Operations Revision 02 Task No. 341013O0303 Approve Radioactive Discharge-Release Permit Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

11. Appropriate Performance Locations: SIM / CR 12. Appropriate Trainee Level: SRO

13. Evaluation Method: Perform 4. Performance Time: 10 minutes

5. NRC K/As 2.1.34 (2

.9); 2.1.32 (3.4/3.8)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to complete a radioacti ve discharge / release permit. 2. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner. 3. Give the trainee his copy of the Directi ons to the Trainee (Attachment 2) and Liquid Radwaste Discharge Form (Attachment

1) when ready to start the JPM. 4. Brief the trainee, and te ll the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to review and complete the radioactive discharge/release permit as Shift Manager. Before y ou start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

====================

========================

General Conditions:

1. The plant is operating at 100%. 2. CWP A, B, and D are in service. 3. De-icing is in progress.

4. The FDST radioactive dischar ge was started at 0905, Jan 6. 5. The FDST radioactive disc harge was stopped at 1355, Jan 6. 6. FDST final level is 10.5%.

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 53 of 149 Job Performance Measure for Operations Revision 02 Task No. 341013O0303 Approve Radioactive Discharge-Release Permit General

References:

1. 8.8.11, Liquid Radioactive Waste Discharge Authorization

General Tools and Equipment:

1. Scientific calculator

Special Conditions, References, Tools, Equipment:

1. Critical steps denoted by "*".

Task Standards:

1. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

As Shift Manager complete the Liquid Radioa ctive Waste Discharge Form for the FDST (Attachment 1) and inform me when a ll required actions are complete.

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 54 of 149 Job Performance Measure for Operations Revision 02 Task No. 341013O0303 Approve Radioactive Discharge-Release Permit Performance Checklist Standards Initials 1. Records Stop Run Data in Section 5.

Operator records Date as 1/6/xx, records time as 1355 and records % tank level as 10.5.

________ 2. Records dilution flow.

Operator refers to Se ction 4.1 and records dilution flow of 308400 gpm.

_______* 3. Records volume of release.

Operator calculates volume of release as 16368.625 (using Usable tank volume and

start and stop tank %).

NOTE: Acceptable value: 16360 to 16380

gallons. _______* 4. Records total time of discharge.

Operator calculates tota l time of discharge in minutes (subtracting start time from end time) and records 290 minutes.

_______* 5. Records discharge flow.

Operator calculates di scharge flow (divides volume of release by total time of discharge)

and records 56-57 gpm.

_______* 6. Records River Level.

Operator records river level as 880 ft MSL.

CUE: River level is 880 ft MSL.

________ 7. Removes Discharge In Progress Tags from running

CWPs. Operator would remove or direct control room operator to remove the tags from the running CWPs. #CUE: Tags are removed.

________

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 55 of 149 Job Performance Measure for Operations Revision 02 Task No. 341013O0303 Approve Radioactive Discharge-Release Permit Performance Checklist Standards Initials 8. Records total river flow.

Operator contacts chemistry for total river flow and records 5.9E7 l/min.

CUE: Chemistry reports total river flow is 5.9E7 l/min. (This may be completed by the Chemist after SM signature.)

________ 9. Completes discharge permit.

Operator signs form as Shift Manager and forwards to Chemistry for review.

CUE: Accept form as Chemist. ________

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 56 of 8 Job Performance Measure for Operations Revision: 02 Attachment 1LIQUID RADIOACTIVE WASTE DISCHARGE FORM ATTACHMENT 1 LIQUID RADIOACTIVE WASTE DISCHARGE FORM Section 1. REQUEST FOR ANALYSIS OF RADIOACTIVE LIQUID WASTE PRIOR TO DISCHARGE To: Chemistry From: Shift Manager Tank To Be Discharged: FDST Started Recirculation For Sample: Time: 0300 Date: 1/6/xx Recirculation Of Tank Complete: Time: 0500 Date: 1/6/xx Estimated Volume To Be Discharged: 98%-10.5% = 87.5%

Shift Manager: Mark Helen Time: 0555 Date: 1/6/xx Section 2. THIS SECTION TO BE COMPLETED BY PERSON TAKING SAMPLE Monitor Source Check Informed Control Room And Performed Source Check Initials: REW Sample Point: 18 Time: 0635 Date: 1/6/xx Signature: Ray Moname Section 3. AUTHORIZATION TO RE LEASE RADIOACTIVE LIQUID WASTE To: Shift Manager From: Chemistry Release Authoriz ation Number:

Total Ci/ml: 3.74E-5 Total Concentration is < 1.0E-02 Ci/ml YES/NO Signature: Ray Moname 31 Day Dose, Percent Of Annual Limit For Each Value Is 2.0E+00 YES/NO Signature: Ray Moname You Are Authorized To Release Subject Tank With Either Of Following Restrictions:

Maximum Liquid Waste Discharge Rate (gpm)

1) 100

2) N/A

3) N/A Minimum Dilution Flow To Canal (gpm)

1) 159,000

2) 159,000

3) 159,000 Discharge Monitor Alarm Setpoint ( Ci/ml) 1) 6.22E-3

2) N/A

3) N/A NOTE - Terminate Discharge If Above Specifications Cannot Be Maintained. Contents Of This Tank Are Within Chemic al Parameters For Discharge.

Chemistry: Ray Moname Time: 0707 Date: 1/6/xx

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 57 of 8 Job Performance Measure for Operations Revision: 02 Section 4. SHIFT MANAGER APPROVAL TO RELEASE 4.1 Circle Appropriate Discharge Canal Flow Rate: AVERAGE CW DISCHARGE FLOWRATE (gpm) NUMBER OF OPERATING CW PUMPS DE-ICING NO DE-ICING 4 378,600 631,000 3 308,400 514,000 2 193,200 322,000 1 118,800 198,000 4.2 To: Operations Personnel From: Shift Manager The Subject Tank Contents Are Appr oved For Release Subject To The Following Restrictions: 1) Maximum Liquid Disch Rate: 100 gpm (Section 3) 2) Minimum Dilution Flow To Canal Of: 159000 gpm (Section 3) 3) Alarm Limits Specified (Section 3) 4) Tank Volume Verified: 98 (Compare To Section 1) 5) DISCHARGE IN PROGRESS Tags In stalled On Running Circ Water Pumps. Approval To Release:

Shift Manager: Mark Helen Time: 0804 Date: 1/6/xx

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 58 of 8 Job Performance Measure for Operations Revision: 02 Section 5. To: Chemist From: Shift Manager The Subject Discharge Has Been Completed And The Following Data Obtained During The Discharge:

START RUN NUMBER DATE TIME

% TANK LEVEL STOP RUN NUMBER DATE TIME

% TANK LEVEL 1 1/6/xx 0905 98 1 2 2 3 3 4 4 Usable Tank Volumes (0% to 100%)

FDST - 18,707 gal

WST A - 20,015 gal

WST B - 20,015 gal 1) Dilution Flow (Section 4.1):

gpm 2) Volume Of Release:

gal 3) Total Time Of Discharge:

min 4) Discharge Flow:

gpm 5) River Level:

ft MSL 6) Remove DISCHARGE IN PROGRESS Ta gs From Running Circ Water Pumps. 7) Total River Flow:

l/min (Determined By The Chemist)

Shift Manager:

Time: Date: Chemist Review:

Date:

Nebraska Public Power District SKL034-50-29 (8908) Cooper Nuclear Station Page 59 of 8 Job Performance Measure for Operations Revision: 02 ATTACHMENT 2

Directions to Trainee:

When I tell you to begin, you are to review and complete the radioactive discharge/release permit as Shift Manager. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

General Conditions:

1. The plant is operating at 100%. 2. CWP A, B, and D are in service. 3. De-icing is in progress. 4. The FDST radioactive dischar ge was started at 0905, Jan 6. 5. The FDST radioactive disc harge was stopped at 1355, Jan 6. 6. FDST final level is 10.5%.

Initiating Cue(s):

As Shift Manager complete the Liquid Radioact ive Waste Discharge Form for the FDST and inform me when all required actions are complete.

Nebraska Public Power District SKL034-30-62 (36404) Cooper Nuclear Station P age 60 of 149 Job Performance Measure for Operations Revision 00 ATWS SCENARIO EAL Trainee: Examiner:

Pass: Fail: Examiner signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: SIM

2. Appropriate Trainee Level: SRO

3. Evaluation Method: Perform

4. Performance Time: 20 minutes

5. NRC K/A 2.4.41 2.3/4.1

Directions to Examiner:

1. This JPM evaluates the trainee's ability to determine the Emergency Action Level from an ATWS Scenario (Scenario 1). 2. Observe the trainee during performance of the JPM for proper use of self-checking methods. 3. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in t he space if desired by the examiner.

General Conditions:

1. As seen during the previous simulator scenario.

General

References:

1. EPIP 5.7.1, Emergency Classification, Revision 33 General Tools and Equipment:

None

Nebraska Public Power District SKL034-30-62 (36404) Cooper Nuclear Station P age 61 of 149 Job Performance Measure for Operations Revision 00 ATWS SCENARIO EAL Special Conditions, References, Tools, Equipment:

1. Simulator Setup: NA

2. Critical checks denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

1. Accurately classify the event using the correct plant procedure.

Initiating Cue(s):

The Shift Manager has directed you to deter mine what the highest Emergency Action Level was during the previous scenario. No tify the Shift Manager when the task is complete.

Nebraska Public Power District SKL034-30-62 (36404) Cooper Nuclear Station P age 62 of 149 Job Performance Measure for Operations Revision 00 ATWS SCENARIO EAL Performance Checklist Standards Initials 1. Consult EAL. Candidate consults EAL procedure.

_______ 2. EAL classification.

Candidate identifies that a Site Area Emergency would have been declared per

EAL 3.3.4. This is because boron was

injected to shut down the reactor.

_______* 3. Inform the SM that the task is complete.

Inform Shift Manager that the Emergency Classification is complete.

CUE: The SM Acknowledges that it is complete. This JPM is complete.

_______

Nebraska Public Power District SKL034-30-62 (36404) Cooper Nuclear Station P age 63 of 149 Job Performance Measure for Operations Revision 00 ATWS SCENARIO EAL

Nebraska Public Power District SKL034-30-62 (36404) Cooper Nuclear Station P age 64 of 149 Job Performance Measure for Operations Revision 00 ATTACHMENT 1 Directions to Candidate:

When I tell you to begin, you are to dete rmine the Emergency Action Level from the ATWS Scenario you just experienced. Befo re you start, I will state the general plant conditions, the initiating cues and answer any questions you may have.

General Conditions:

1. As seen during the previous simulator scenario.

Initiating Cues:

The Shift Manager has directed you to deter mine what the highest Emergency Action Level was during the previous scenario. No tify the Shift Manager when the task is complete.

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 65 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

Trainee:

Examiner:

Pass [ ]; Fail [ ] Ex aminer Signature:

Date:

Additional Program Information:

NOTE THIS IS AN ALTERNATE PATH JPM. 1. Appropriate Perfo rmance Locations: CR/SIM 2. Appropriate Trainee Level: RO/SRO 3. Evaluation Method: Perform Simulate

4. Performance Time: 8 minutes 5. NRC K/As 202001 A2.03 (3.6/3.7)

Directions to Examiner:

NOTE THIS IS AN ALTERNATE PATH JPM. The flow subtracting network will fail and require manual input of total core flow.

5. This JPM evaluates the trainee's ability to respond to a Reactor Reci rculation pump trip per 2.4RR, "Reactor Recirculation Abnormal." 6. If this JPM is performed on t he Simulator, only the cues preceded by "#" should be given. 7. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner. 8. Give the trainee his copy of the Directions to the Trainee (Attachment 2) when ready to start the JPM. 9. Brief the trainee, place the Simulato r in RUN, and tell the trainee to begin.

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 66 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

Directions to Trainee:

When I tell you to begin, you are to perform actions as appropriate to panel 9-4 and 9-5 indications. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any me ters, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repositioning controls and observing instrumentation.

====================

========================

General Conditions:

7. The plant is operating at power. 8. You are the Cont rol Room Operator.

General

References:

1. Procedure 2.4RR, Reacto r Recirculation Abnormal 2. Procedure 2.2.68.1, Reactor Re circulation System Operations

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 67 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

General Tools and Equipment:

1. None Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1. 2. Critical steps denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

1. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The Control Room Supervisor directs you to per form actions as appropriate to panel 9-4 and panel 9-5 indications.

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 68 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

Performance Checklist Standards Initials 1. Assume the watch at panel 9-5. The operator positions himself in a position to monitor panel 9-5.

ACTION: After the candidate assumes the watc h, activate TRIGGER E1 to trip "B" Reactor Recirculation Pump.

2. Recognize and report trip of Recirc pump.

The operator recognizes and reports the trip of "B" Reactor Recirculation pump.

CUE: Acknowledge the report as CRS. Directs the operator to perform his

actions per the abnormal.

3. Take appropriate immediate actions. The operator evaluates 2.4RR immediate actions; determines none apply.

4. Obtain procedure 2.4RR.

The operator obtains a copy of 2.4RR.

5. Enter Attachment 1 of 2.4RR Operator enters Atta chment 1 of 2.4RR.

6. Evaluate need to enter Attachment 3 for stability exclusion region.

Operator evaluates the need to enter for stability exclusion region; determines entry is required.

CUE: Acknowledge the report as CRS and another operator will address stability exclusion region.

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 69 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

Performance Checklist Standards Initials 7. Ensure RRMG Set B GEN FIELD BKR open.

Operator ensures RR MG Set B GEN FIELD BKR open.

CUE: RRMG Set B GEN FIELD BKR green light is illuminated, the red light is out.

8. Close RR-MO-53B, PUMP DISCHARGE VLV.

Operator closes RR-MO-53B, PUMP DISCHARGE VLV.

CUE: RR-MO-53B green light is lit and the red light is out.

NOTE: The operator should continue with the remaining 2.4RR steps while waiting for the RR-MO-53B valve.

9. After RR-MO-53B has been closed for 5 minutes, open

valve. Operator opens RR-MO-53B after it has has been closed for 5 minutes (-0, + 5 minutes).

CUE: RR-MO-53B green light is out and red light is lit (after valve has been

opened). 10. Ensure operating RRMG is transferred to Startup

Transformer per Procedure 2.2.18. Operator ensures "A" RRMG is powered by the Startup Transformer.

CUE: "A" RRMG is powered by the Startup Transformer (Breaker 1CS is closed).

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 70 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

Performance Checklist Standards Initials 11. Maintain oil outlet temperature for tripped RRMG 90 F to 130 F. Operator directs Station Operator to maintain oil outlet temperatur e for tripped RRMG 90 F to 130 F. #CUE: Acknowledge/repeat back order as Station Operator.

12. Monitor loop cooldown rate on RR-TR-165, RR SUCTION & FEEDWATER TEMP. Operator monitors loop cooldown rate on RR-TR-165, RR SUCTION & FEEDWATER

TEMP.

CUE: Loop temperature has dropped 6 F over the last 5 minutes.

13. Concurrently enter Single Loop Operation per

Procedure 2.2.68.1.

Operator obtains a copy of 2.2.68.1.

14. Dispatch Operators to R-976-W and Non-Critical

Switchgear Room to record

lockout relays and targets for

tripped pump.

Operator dispatches Operators to R-976-W and Non-Critical Switchgear Room to record

lockout relays and targets for tripped pump.

CUE: Overcurrent (51 relay) is tripped for breaker 1DN (in Non-Critical Switchgear Room). There are no

lockouts at Reactor Building 976

West. 15. If total core flow < 20%, concurrently enter .

Operator determines Core Flow is above 20%

rated.

CUE: Indicated core flow is 41 Mlbm/hr.

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 71 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

Performance Checklist Standards Initials 16. Align RRMG H&V System per Procedure 2.2.85.

Operator aligns RRMG H&V System per Procedure 2.2.85.

CUE: When operator initiates action to align ventilation, inform him that another operator will perform the ventilation alignment.

17. Raise core flow to

> 29.5x10 6 lbs/hr, if possible.

Operator determines core flow is >

29.5x10 6 lbs/hr CUE: Indicated core flow is 41 Mlbm/hr.

18. Determine if reverse flow summer is functioning.

Operator determines reverse flow summer is NOT functioning as annun ciator 9-4-3/E-7 is NOT in and indicated core flow is NOT

approximately equal to difference between NBI-FI-92A and NBI-FI-92B

CUE: 9-4-3/E-7 is NOT alarming.

CUE: NBI-FI-92A reads 37 Mlbm/hr. NBI-FI-92B reads 4 Mlbm/hr.

19. Initiate an emergency Work Order to repair or replace

reverse flow summer (NBI-SUM-97).

Operator initiate an emergency Work Order to repair or replace reverse flow summer (NBI-SUM-97).

CUE: Another operator will perform this task.

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 72 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

Performance Checklist Standards Initials 20. Determine difference between NBI-FI-92A and NBI-FI-92B loop flows.

Operator determines difference between NBI-FI-92A and NBI-FI-92B loop flows is 31x10 6 lbs/hr.

NOTE: Entering substitute value for point B012 is accomplished using an IDT terminal and pressing the "Bogey Value" button. On screen prompts will guide the rest of the substitution.

21. Enter substitute value for PMIS Point B012.

Operator enters difference between NBI-FI-92A and NBI-FI-92B loop flows as

substitute for PMIS Point B012.

CUE: PMIS Point B012 has been substituted for.

CUE: SIMULATOR ONLY.

Ask the candidate to verify that the core flow value has updated on the power to flow map.

22. Verify value substituted for PMIS Point B012 (Simulator

ONLY). Operator enters turn-on code of PFMAP and verifies core flow value matches value

substituted.

NOTE: As soon as the student attempts to contact the Reactor Engineer, tell them that the JPM is complete.

23. Initiate actions to notify the Reactor Engineer about MCPR. Initiate actions to notify the Reactor Engineer that MCPR needs to be adjusted for single loop operations

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 73 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

ATTACHMENT 1 SIMULATOR SET-UP

A. Materials required None B. Initialize the Simulator in any fu ll power IC (IC-18, 19 or 20 suggested)

Batch File name - none.

C. Change the Simulator conditions fr om those of the IC as follows:

1. Triggers Number File Name Description E1 None trgset 11 "zlorrmgfbb(1)==1" ^"B" Recirc MG Field Breaker green light on

2. Malfunctions Number Title Trigger TD Severity Ramp Initial RR04D "B" Reactor Recirculation Pump Drive Motor Breaker Trip (1DN)

E1 N/A N/A N/A N/A 3. Remotes Number Title Trigger TD Value Ramp None Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Revision 02 Job Performance Measure Page 74 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:202022C0401

==========================

=====================

= Task Title: Respond to a Trip of a Reacto r Recirc Pump (Alternate Path)

==========================

======================

4. Overrides Instrument Tag Trigger TD Value Ramp 9-4-3/E-7, RECIRC LOOP B OUT OF SERVICE RA:MUX08C108 A 0 OFF 0 Total Core Flow ZAONBIDPRFR95[2] E1 0:10 41 0:10 "A" Loop Flow ZAONBIFI92A E1 0:12 37 0:12 "B" Loop Flow ZAONBIFI92B E1 0:15 4 1:00

5. Panel Set-up (suggested.)

a. Insert listed overrides and malfunctions.

b. Place the Simulator in RUN.

c. Ensure "A" Reactor Recirculation pump is aligned to the Startup Transformer.

d. Ensure "B" Reactor Recirculation pum p is aligned to the Normal Transformer.

e. Ensure that the curser on the power to flow map is within the normal operating region. Note: If this JPM is to be perfo rmed more than once, snap the Si mulator into an IC after the panel set-up is complete.

Nebraska Public Power District SKL034-21-56 (8779) Cooper Nuclear Station Page 75 of 11 Job Performance Measure for Operations Revision: 02 ATTACHMENT 2

Directions to Trainee:

When I tell you to begin, you are to perform actions as appropriate to panel 9-4 and 9-5 indications. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

General Conditions:

9. The plant is operating at power. 10. You are the CRO - Reactor Operator (RO) (9-5 PNL). 11. Optimum Water Chemistry is out of service.

Initiating Cue(s):

The Control Room Supervisor directs you to per form actions as appropriate to panel 9-4 and panel 9-5 indications.

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 76 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path)

Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

THIS IS AN ALTERNATE PATH JPM

1. Appropriate Performance Locations: CR / SIM

2. Appropriate Trainee level: RO / SRO

3. Evaluation Method:

Simulate Perform 4. Performance Time: 20 minutes

5. NRC K/A 259001 A4.02 (3.9/3.7)

Directions to Examiner:

NOTE: THIS IS AN ALTERNATE PATH JPM. THE INITIAL ATTEMPT TO RESET THE RFPT TRIP WILL FAIL AND REQUIRE USE OF THE ALTERNATIVE METHOD TO RESET THE TRIP.

1. This JPM evaluates the trainee's abili ty to perform a quick start of a RFPT 2. If this JPM is performed on the Simulator, only the cues preceded by "#" should be given. 3. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in t he space if desired by the examiner.

4. DO NOT place the simulator in RUN until the student is ready to perform the JPM. (RFP must be coasting down or on turning gear < 5 minutes to use this procedure section.) 5. Give the trainee his copy of the Directions to the Trainee (Attachment 2) when ready to start the JPM. 6. Brief the trainee, place the simulato r in run, and tell t he trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to perform a quick start of the "A" RFPT. Before you start, I will state the general plant conditions, the Initiating Cues and ans wer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any meters, gauges, recorders and controls you Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 77 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path) would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you ar e taking, e.g.: repositioning controls and observing instrumentation.

==========================

==================

General Conditions:

1. The Reactor has scrammed.

2. Both RFPs have tripped on high level.

General

References:

1. Procedure 2.2.28

8. Procedure 2.2.28.1

General Tools and Equipment:

1. None Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1.

2. Critical checks denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

1. 100% of critical elements su ccessfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The Control Room Supervisor directs you to re start "A" RFP in Reacto r Pressure Follow Mode and raise RPV water level to the GREEN Band using the quick restart hard card.

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 78 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path)

Performance Checklist Standards Initials 1. Ensure RFPT time limit is met.

Ensure RFPT coasting from trip or not on turning gear > 5 minutes after trip.

CUE: RFPTs are still coasting down.

_______

NOTE: RFPT Trips are as follows:

1. Low pump suction pressure of 260 psig after a 15 second time delay 2. Exhaust casing high pressure at 7" Hgv 3. Exhaust casing high temperature of 23 F 4. Low lube oil pressure of 10 psig 5. Thrust bearing wear at 10 psig oil pressure 6. High reactor water le vel of 52.5" (Tech Spec

< 54") 7. Electrical overspeed at 5950 rpm 8. Mechanical overspeed at 6050 to 6150 rpm 9. Emergency trip pushbutton operation

2. Ensure RFPT trips are reset. Ensure RFPT trips (except high water level) are reset. Check the following annunciators are clear: - A-1/A-6 (Low Suct ion Pressure), - A-1/B-4 (Exhaust Hood High Temp),

- A-1/B-5 (Low Vacuum Trip),

- A-1/B-6 (Thrust Bearing Trip),

- A-1/C-4 (Low Oil Pressure Pre Trip) Ensure reactor water level is < 54"

Check RFPT/Main Turbine high RPV water level trip amber lights (panel 9-5)

CUE: All trips (except high RPV water level) are reset. _______

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 79 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path)

3. Ensure High RPV water level RFPT trips are reset. At Panel 9-5, reset at least 2 of the HIGH WATER LEVEL TRIPS.

CUE: All 3 High RPV water level trips were in and now have been reset.

_______*

4. Ensure RFP-CS-RFPT-A RFPT A Control Station is in MDVP Operator ensures RFP-CS-RFPT-A is in MDVP CUE: RFP-CS-RFPT-A is in MDVP

_______ 5. Ensure OUTPUT on RFP-CS-RFPT-A is adjusted to minimum. Operator ensures OUTPUT on RFP-CS-RFPT-A is adjusted to minimum.

CUE: OUTPUT on RFP-CS-RFPT-A is adjusted to minimum. _______ 6. Attempt to reset "A" RFPT Press and hold RFPT A TRIP RESET button. Note the RFPT A HP and LP STOP valves are NOT open.

CUE: HP and LP STOP valves red light are OFF Green lights are ON. _______ 7. Recognize and report the trip reset failure.

Recognize and report the "A" RFPT trip reset failure. _______ 8. Reset "A" RFPT Press and hold RFPT A OVERSPEED TRIP BLOCK and RFPT A OVERSPEED TRIP RESET.

CUE: HP and LP STOP valves red lights are ON Green lights are OFF. _______* 9. Ensure RF-11A is OPEN Ensure RF-FCV-11A, MIN FLOW VALVE, is open. CUE: RF-FCV-11A Red light is ON and Green light OFF. _______

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 80 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path)

10. Select RFP At a HMI, select FEEDPUMP A screen for desired RFP to be started.

CUE: "A" RFP selected

_______ 11. Select Quick Restart.

Select QUICK RESTART start type.

CUE: Quick restart selected

_______* 12. Select HP Start.

If extraction steam is available, select LP START.

Otherwise, select HP START.

.CUE: HP Start selected . _______* 13. Press green Start button and confirm start in pop-up box.

Press green START button and confirm start in pop-up box

CUE: Start in Pop-up box.

_______* 14. Continue Button After RFP A(B) reaches MINIMUM GOVERNOR, depress green CONTINUE button.

CUE: green CONTINUE button depressed.

_______* 15. Ensure injection path Ensure injection path is aligned to the reactor vessel, as dictated by plant conditions

CUE: Path lined up

_______ 16. Raise speed Use UP arrow to raise RFP speed to raise RFP discharge pressure.

CUE: RFP speed rising.

_______

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 81 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path)

17. Place In Reactor Pressure Follow Place RFP in desired mode (e.g., AUTO or REACTOR PRESSURE FOLLOW).

CUE: In Reactor pressure follow

_______* 18. Raise Level If required, adjust STARTUP MASTER controller using UP/DOWN arrows or RAMP FUNCTION, to adjust LEVEL SETPOINT as desired.

CUE Level at 35" _______* 19. Inform the CRS that the task is Complete.

Inform the Control Room Supervisor that 1A RFP has been restarted and injecting into the RPV

CUE: CRS acknowledges the report.

_______

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 82 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path)

ATTACHMENT 1 SIMULATOR SET-UP A. Materials Required None B. Initialize the Simulator in IC Any IC that will support this JPM C. Run Batch File None D. Change the simulator

conditions as

follows: Number Title Tgr TD Sev Ramp Initial 1. Triggers None 2. Malfunctions RR19 Shutdown Cooling Loss

of Mass 100 N/A N/A 3. Remotes None N/A N/A 4. Overrides ZDIRFSWRFTRA[1]

RFPT-A Trip Reset Pushbutton OFF 5. Panel Setup a. Place the Simulator in run. b. Use Monitor Parameter RRMRVLOSS to reset malfunction RR19.

c. Place the Mode Switch to Shutdown.

d. Secure two Condensate and Condensate Booster pumps.

e. If water level needs to be lowered insert RR19.

f. Ensure the "A" RFP is still coasting down or is on the turning gear.

g. Ensure RPV water level is < +50" (narrow range).

h. Insert listed switch override.

i. Place the Simulator in FREEZE un til the operator is ready to begin.

Note: If this JPM is to be performed more than once, take a SN APSHOT after the panel setup is complete.

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 83 of 149 Job Performance Measure for Operations Revision 00

Task No.: 259058G401 Perform a Quick Restart of RFPT A (Hard Card) (Alternate Path)

Nebraska Public Power District SKL034-22-03 (36408) Cooper Nuclear Station Page 84 of 149 Job Performance Measure for Operations Revision 00 ATTACHMENT 2 Directions to Trainee:

When I tell you to begin, you are to perform a quick start of the "A" RFPT. Before you start, I will state the general plant conditions, the Initiating Cues and ans wer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

General Conditions:

1. The Reactor has scrammed.

2. Both RFPs have tripped on high level.

Initiating Cues:

The Control Room Supervisor directs you to re start "A" RFP in Reacto r Pressure Follow Mode and raise RPV water level to the GREEN Band using the quick restart hard card.

Nebraska Public Power District SKL034-21-48 (7405) Cooper Nuclear Station Revision 02 Job Performance Measure Page 85 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:206005O0101

==========================

=====================

= Task Title: Manually Initiate HPCI (H ard Card) (Alternate Path)

==========================

======================

Trainee:

Examiner:

Pass [ ]; Fail [ ] Ex aminer Signature:

Date:

Additional Program Information:

NOTE THIS IS AN ALTERNATE PATH JPM.

1. Appropriate Perfo rmance Locations: CR/SIM 2. Appropriate Trainee Level: RO/SRO 3. Evaluation Method: Perform Simulate

4. Performance Time: 8 minutes 5. NRC K/As 206000 K3.02 (3.8/3.8) and A4.01 (3.8/3.7)

Directions to Examiner:

NOTE THIS IS AN ALTERNATE PATH JPM. THE FLOW CONTROLLER WILL FAIL TO OPERATE IN AUTOMATIC AND MUST BE PLACED IN MANUAL.

10. This JPM evaluates the trainee's ability to perform the "injection mode" of operation of HPCI per the guidance of pr ocedure 2.2.33.1, High Pressure Coolant Injection System Operations (hard card).

11. If this JPM is performed on t he Simulator, only the cues preceded by "#" should be given.

12. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner.

13. Give the trainee his copy of the Directions to the Trainee (Attachment 2) when ready to start the JPM.

14. Brief the trainee, place the Simulato r in RUN, and tell the trainee to begin.

Nebraska Public Power District SKL034-21-48 (7405) Cooper Nuclear Station Revision 02 Job Performance Measure Page 86 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:206005O0101

==========================

=====================

= Task Title: Manually Initiate HPCI (H ard Card) (Alternate Path)

==========================

======================

Directions to Trainee:

When I tell you to begin, you are to operate HPCI in the injection mode at rated flow using the hard card. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you ar e taking, e.g.: repositioning controls and observing instrumentation.

====================

========================

General Conditions:

12. The Reactor is shutdown following a scram. 13. Reactor pressure is currently being maintained by another operator. 14. Suppression Pool Cooling will be placed in service by another operator. 15. SBGT and REC have been aligned to support HPCI operation.

General

References:

1. Procedure 2.2.33.1, High Pressure C oolant Injection System Operation.

Nebraska Public Power District SKL034-21-48 (7405) Cooper Nuclear Station Revision 02 Job Performance Measure Page 87 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:206005O0101

==========================

=====================

= Task Title: Manually Initiate HPCI (H ard Card) (Alternate Path)

==========================

======================

General Tools and Equipment:

1. None Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1. 2. Critical steps denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

2. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The Control Room Supervisor directs you to plac e HPCI in the injection mode at rated flow using the hard card. Inform the CRS wh en HPCI is injecting at rated flow.

Nebraska Public Power District SKL034-21-48 (7405) Cooper Nuclear Station Revision 02 Job Performance Measure Page 88 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:206005O0101

==========================

=====================

= Task Title: Manually Initiate HPCI (H ard Card) (Alternate Path)

==========================

======================

Performance Checklist Standards Initials 24. Place GLAND SEAL CNDSR BLOWER control switch in START. The operator places the control switch for the GLAND SEAL CNDSR BLOWER in START.

CUE: The red light for the GLAND SEAL CNDSR BLOWER is lit, the green

light is out.

25. Checks High Water Level Trip Checks and Resets REACTOR HI WTR LEVEL TRIP SIGNAL.

CUE: REACTOR HI WTR LEVEL TRIP yellow light is OFF.

26. Open HPCI-MO-14, STM TO TURB VLV.

The operator places the control switch for the HPCI-MO-14 in OPEN.

CUE: HPCI-MO-14 red light is on, green light is off.

27. Start AUXILIARY OIL PUMP by placing control switch in START. The operator places the control switch for the Auxiliary Oil Pump switch to START.

CUE: HPCI Aux Oil pum p red light is on, green light is off.

28. Open HPCI-MO-19, INJECTION VALVE.

The operator places the control switch for the HPCI-MO-19 in OPEN.

CUE: HPCI-MO-19 red light is on, green light is off.

Nebraska Public Power District SKL034-21-48 (7405) Cooper Nuclear Station Revision 02 Job Performance Measure Page 89 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:206005O0101

==========================

=====================

= Task Title: Manually Initiate HPCI (H ard Card) (Alternate Path)

==========================

======================

Performance Checklist Standards Initials 29. Adjust FLOW CONTROLLER

HPCI-FIC-108 setpoint to

maintain desired HPCI flow, as necessary.

Operator attempts to control HPCI flow with the Set Tape.

CUE: HPCI flow remains almost zero, irrespective of Set Tape setting.

30. Operator recognizes and reports failed controller Operator reports to CR S that HPCI controller has failed in automatic.

CUE: CRS acknowledges, directs operator to continue with HPCI injection

31. Operator places HPCI controller in manual.

Operator turns HPCI controller AUTO/BAL/MAN switch to MAN.

CUE: HPCI controller AUTO/BAL/MAN switch is in MAN.

32. Operator adjusts HPCI controller in manual to control flow.`

Operator turns HPCI controller manual knob clockwise to raise flow, counter-clockwise to lower flow until flow is 4250 gpm.

CUE: HPCI flow responds to manual control knob adjustment as

appropriate.

33. Operator repor ts HPCI is in injection mode at rated flow.

Operator reports HPCI is in injection mode at rated flow per the hard card.

CUE: CRS acknowledges report.

Nebraska Public Power District SKL034-21-48 (7405) Cooper Nuclear Station Revision 02 Job Performance Measure Page 90 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:206005O0101

==========================

=====================

= Task Title: Manually Initiate HPCI (H ard Card) (Alternate Path)

==========================

======================

ATTACHMENT 1 SIMULATOR SET-UP A. Materials required None C. Initialize the Simulator in any IC that will support HPCI injection mode after a scram (IC-18, 19 or 20 suggested)

Batch File name - none.

C. Change the Simulator conditions fr om those of the IC as follows:

1. Triggers Number File Name Description None 2. Malfunctions Number Title Trigger TD Severity Ramp Initial RC01 RCIC System Failure to Auto Start A N/A N/A N/A N/A HP01 HPCI System Failure to Auto Start A N/A N/A N/A N/A 3. Remotes Number Title Trigger TD Value Ramp None Nebraska Public Power District SKL034-21-48 (7405) Cooper Nuclear Station Revision 02 Job Performance Measure Page 91 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:206005O0101

==========================

=====================

= Task Title: Manually Initiate HPCI (H ard Card) (Alternate Path)

==========================

======================

4. Overrides Instrument Tag Trigger TD Value Ramp HPCI Set Tape ZAIHPCIFIC108[2]

A 0 200 0 5. Panel Set-up (suggested. Any setup is allowed that supports performance of the HPCI injection mode)

a. Insert listed overrides and malfunctions.

b. Place the Simulator in RUN.

c. Trip both RFPs.

d. Trip the CRD pump.

e. Reset HPCI high level trip signal (if present).

f. Place the Simulator in FREEZE.

Note: If this JPM is to be per formed more than once, snap the Si mulator into an IC after the panel set-up is complete.

Nebraska Public Power District SKL034-21-48(7405) Cooper Nuclear Station Page 92 of 8 Job Performance Measure for Operations Revision: 02 ATTACHMENT 2

Directions to Trainee:

When I tell you to begin, you are to operate HPCI in the injection mode at rated flow using the hard card. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

General Conditions:

16. The Reactor is shutdown following a scram. 17. Reactor pressure is being maintained by another operator.

18. Suppression Pool Cooling will be placed in service by another operator. 19. SBGT and REC have been aligned to support HPCI operation.

Initiating Cue(s):

The Control Room Supervisor directs you to plac e HPCI in the injection mode at rated flow using the hard card. Inform the CRS wh en HPCI is injecting at rated flow.

Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 93 of 8 Job Performance Measure for Operations Revision: 01 Task No.: 213003P0101

======================================================

Task Title:

Verify a Group 3 Primary Containment Isolation (Alternate Path)

======================================================

Trainee:

Examiner:

Pass:

Fail: Examiner Signature:

Date:

NOTE THIS IS AN ALTERNATE PATH JPM.

Additional Program Information:

1. Appropriate Performance Locations: CR / SIM 2. Appropriate Trainee level: RO / SRO / STE 3. Evaluation Method: Perform Simulate

4. Performance Time: 8 minutes 5. NRC K/As 2.1.31 (4.2/3.9) and 223002 A4.01 (3.6/3.5)

Directions to Examiner:

NOTE: THIS IS AN ALTERNATE PATH JPM. THE RWCU-MO-15 and RWCU-MO-18 WILL FAIL TO AUTOMATICALLY CLOSE AND MUST BE MANUALLY CLOSED. 15. This JPM evaluates the trainee

=s ability to verify a Group 3 Primary Containment Isolation per the hard card in procedure 2.1.22, Recovering from a Group Isolation.

16. This JPM is an alternate path, it evaluates the trainee

=s ability to identify a failure of Group 3 Primary Containment Isolation valves to close and to take action to ensure the Primary Containment Isolation occurs.

17. If this JPM is performed on the Simulator, only the cues preceded by A#@ should be given.

18. All blanks must be filled out with either initials or an A NP@ for A not performed

@; an explanation may also be written in the space, if desired, by the examiner.

19. IF asked, it is acceptable to use the hard card to perform the isolation verification.

Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 94 of 8 Job Performance Measure for Operations Revision: 01 Task No.: 213003P0101

======================================================

Task Title:

Verify a Group 3 Primary Containment Isolation (Alternate Path)

======================================================

20. Give the trainee his copy of the Directions to the Trainee (Attachment 2) when ready to start the JPM.

21. Brief the trainee, place the Simulator in RUN, and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to verify a Group 3 Primary Containment Isolation using the hard card. Before you start, I will

state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you ar e taking, e.g.: repositioning controls and observing instrumentation.

General Conditions:

20. The Reactor is shutdown following a transient and scram.

21. EOP 1A has been entered.

General

References:

1. Procedure 2.1.22, Recovering from a Group Isolation.

General Tools and Equipment:

1. None Special Conditions, References, Tools, Equipment:

Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 95 of 8 Job Performance Measure for Operations Revision: 01 Task No.: 213003P0101

======================================================

Task Title:

Verify a Group 3 Primary Containment Isolation (Alternate Path)

================================================================== 1. Simulator Setup: See Attachment 1. 2. Critical steps denoted by A*@. 3. Simulator cues denoted by A#@. Task Standards:

3. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and ra diological work practices.

Initiating Cue(s):

The Control Room Supervisor directs you to verify a Group 3 Primary Containment Isolation. Inform the CRS when you have completed the verification.

Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 96 of 8 Job Performance Measure for Operations Revision: 01 Task No.: 213003P0101

======================================================

Task Title:

Verify a Group 3 Primary Containment Isolation (Alternate Path)

======================================================

Performance Checklist Standards Initials

34. Obtains 2.1.22 Hard Card (or 2.1.22).

Hard Card (or procedure 2.1.22) obtained

35. Verifies Group 3 isolation signal is present. Observes the four Group 3 Isolation Indicating lights on panel 9-5 are OFF.

CUE: Channel A and B (4) White indicating lights are OFF.

36. Verifies RWCU-MO-15 is closed.

Operator observes indicating lights for RWCU-MO-15 on panel 9-3 and determines valve failed to close.

CUE: The green light is OFF and the Red light is ON.

37. Manually closes RWCU-MO-15.

Operator places the control switch for RWCU-MO-15 in CLOSE and observes the green light ON and the red light OFF.

CUE: When control switch is placed to CLOSE then green light is ON and red light is OFF.

38. Verifies RWCU-MO-18 is closed.

Operator observes indicating lights for RWCU-MO-18 on panel 9-3 and determines valve failed to close.

Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 97 of 8 Job Performance Measure for Operations Revision: 01 Task No.: 213003P0101

======================================================

Task Title:

Verify a Group 3 Primary Containment Isolation (Alternate Path)

======================================================

Performance Checklist Standards Initials CUE: The green light is OFF and the Red light is ON.

39. Manually closes RWCU-MO-18.

Operator places the control switch for RWCU-MO-18 in CLOSE and observes the green light ON and the red light OFF.

CUE: When control switch is placed to CLOSE then green light is ON and red light is OFF.

40. Crack open RWCU-MO-74, Demin Suction Bypass Valve.

Operator places the control switch for RWCU-MO-74 in OPEN position until dual valve

position indication is observed.

CUE: Both green light and red light are ON.

41. Informs CRS that the group 3 isolation has been verified.

CRS informed that the Group 3 isolation is verified and that RWCU-MO-15 and 18 failed to isolate and were manually closed. #CUE: As the CRS acknowledge the report.

Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 98 of 8 Job Performance Measure for Operations Revision: 01 Task No.: 213003P0101

======================================================

Task Title:

Verify a Group 3 Primary Containment Isolation (Alternate Path)

======================================================

ATTACHMENT 1 SIMULATOR SET-UP A. Materials required None B. Initialize the Simulator in any IC with the reactor at 100%

power.(IC-18, 19 or 20 suggested)

Batch File name - none.

C. Change the Simulator conditions from those of the IC as follows:

1. Triggers Number File Name Description E8 Group 2 isolation zlopcisrelk5ac[1]==0

2. Malfunctions Number Title Trigger TD Severit y Ramp Initi al RP12 Group 3 Isolation Failure A 0 NA NA NA 3. Remotes Number Title Trigger TD Value Ramp None Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 99 of 8 Job Performance Measure for Operations Revision: 01 Task No.: 213003P0101

======================================================

Task Title:

Verify a Group 3 Primary Containment Isolation (Alternate Path)

======================================================

4. Overrides Instrument Tag Trigge r TD Value Ramp Group 3 ISOL IND LIGHT zlopcisrelk26(1) 8 0 OFF 0 Group 3 ISOL IND LIGHT zlopcisrelk26(2) 8 0 OFF 0 Group 3 ISOL IND LIGHT zlopcisrelk27(1) 8 0 OFF 0 Group 3 ISOL IND LIGHT zlopcisrelk27(2) 8 0 OFF 0 5. Panel Set-up (suggested. Any setup that results in a Group 3 isolation signal.)

a. Place the Simulator in RUN.

Insert a scram.

c. Verify a Group 3 isolation signal is present (low reactor water level). i. Place the Simulator in FREEZE.

Note: If this JPM is to be performed more than once, snap the Simulator into an IC after the panel set-up is complete.

Nebraska Public Power District SKL034-21-60(8901) Cooper Nuclear Station Page 100 of 8 Job Performance Measure for Operations Revision: 1 ATTACHMENT 2 Directions to Trainee:

When I tell you to begin, you are to Verify a Group 3 Primary Containment Isolation per the hard card. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repositioning controls and observing instrumentation.

General Conditions:

b. The Reactor is shutdown following a transient and scram.

c. EOP 1A has been entered.

Initiating Cue(s):

The Control Room Supervisor directs you to verify a Group 3 Primary Containment Isolation. Inform the CRS when you have completed the verification.

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 101 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: CR / SIM

2. Appropriate Trainee level: RO / SRO

3. Evaluation Method:

Simulate Perform 4. Performance Time: 20 minutes

5. NRC K/A:262001 A4.04 (3.6/3.7)

Directions to Examiner:

22. This JPM evaluates the trainee's ability to perform transfer of 4160 bus 1G from DG2 to the Emergency Transformer. 23. If this JPM is performed on the Si mulator, only the cues preceded by A#@ should be given. 24. All blanks must be filled out with either initials or an A NP@ for A not performed

@; an explanation may also be written in the space, if desired, by the examiner. 25. Give the trainee his copy of the Directions to the Trainee (Attachment 2) when ready to start the JPM. 26. Brief the trainee, place the Simulato r in RUN, and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to perform the required actions to transfer 4160V bus 1G from DG2 to the Emergency Transformer.

Before you start, I will stat e the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 102 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer

==========================

===================

General Conditions:

1. DG2 is supplying 4160 VAC bus 1G.

2. The Emergency Transformer is available.

3. Breaker 1GB has failed.

General

References:

1. Procedure 2.2.18, 4160V Auxiliary Power Distribution System 2. Procedure 2.2.20.1, Diese l Generator Operations

General Tools and Equipment:

1. None

Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1. 2. Critical steps denoted by A*@. 3. Simulator cues denoted by A#@. Task Standards:

22. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The Control Room Supervisor dire cts you to perform transfer of 4160V bus 1G from DG2 to the Emergency Transformer. Inform Control Room Supervisor when 4160V bus 1G is being carried by the Emergency Transformer.

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 103 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer Performance Checklist Standards Initials 1. Obtain copy of 2.2.18 and 2.2.20.1.

Operator obtains a copy of procedure 2.2.18 and 2.2.20.1.

_________

2. Ensure risk has been assessed, per Procedure

0.49, for placing Breaker

1FS, EMERGENCY XFMR

BKR, for Bus 1F in PULL-TO-LOCK The operator determines that risk need not be assessed as breaker is already open due to a

failure.

CUE: IF asked as CRS, inform the operator that risk has been evaluated.

_________

3. Ensure the Emergency Transformer is energized The operator verifies voltage available from the Emergency Transformer.

CUE: Emergency Transformer secondary voltage is 4440VAC.

_________

4. Inform Shift Manager both off-site circuits are inoperable.

Inform Shift Manager to declare both off-site circuits inoperable and to enter the

appropriate Condition and Required Action of

LCO 3.8.1, AC Sour ces - Operating.

CUE: SM acknowledges the information.

_________

5. Verify 1GS racked in.

Ensure Breaker 1GS, EMERGENCY TRANSFORMER FEED TO 4160V BUS 1G, is racked in.

CUE: 1GS Breaker RED light OFF, GREEN light ON.

_________

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 104 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer Performance Checklist Standards Initials 6. Start signals clear Ensure DG2 auto start signals clear.

CUE: Drywell pressure is .5 pig and steady Reactor water level being controlled

15" to 40".

CUE: 4160V Bus 1F/1G are energized

_________

7. Depress local RESET button Direct SO to locally at DG2 Control Panel, press and release EMERGENCY to NORMAL

RESET button

CUE: Station Operator reports EMERGENCY to NORMAL RESET

button has been depressed and

released ________*

8. Place into Droop Parallel to Parallel.

Direct SO to locally at DG2 Control Panel, ensure DROOP PARALLEL switch is in PARALLEL.

CUE: Station Operator reports DROOP PARALLEL switch is in PARALLEL.

________*

9. Speed control check Adjust speed of DG2 by placing DIESEL GEN 2 GOVERNOR SWITCH to RAISE or LOWER to verify DG2 frequency control.

CUE: DG2 frequency is 59.6 Hz

CUE: DG2 frequency rises to 60.0 Hz

_________

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 105 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer Performance Checklist Standards Initials 10. Voltage control check Adjust voltage of DG2 by placing DIESEL GEN 2 VOLTAGE REGULATOR switch

RAISE or LOWER to main tain DG2 voltage at 4160 volts.

CUE: DG voltage is 4050 volts.

CUE: DG voltage rises to 4160 volts.

_________

11. Synch switch to 1GS Place SYNCH SWITCH 1GS to 1GS.

CUE: SYNCH SWITCH is in 1GS position

________ *

12. Adjust speed Using DIESEL GEN 2 GOVERNOR switch, adjust engine speed so SYNCHROSCOPE is rotating very slowly in counter-clockwise (slow) direction.

CUE: If the operator indicates that he is placing the governor switch to raise indicate that the SYNCHROSCOPE is

speeding up in the clockwise (fast) direction.

CUE: If the operator indicates that he is placing the governor switch to lower indicate that the SYNCHROSCOPE

starting to rotate in the counter-clockwise (slow) direction.

_________

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 106 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer Performance Checklist Standards Initials 13. Adjust voltage Using DIESEL GEN 2 VOLTAGE REGULATOR switch, adjust Bus 1G voltage

to slightly lower than EMERGENCY XFMR

VOLTAGE CUE: (Before adjustment) DG2 Voltage reads 4160 volts.

CUE: XFMR Transformer voltage is 4449 volts.

CUE: (after adjustment) DG2 voltage reads 4430 volts.

________ *

14. Close 1GS When SYNCHROSCOPE is at 1 o

=clock, the operator closes Breaker 1GS and check switch spring returns to NORMAL AFTER

CLOSE (red flagged)

CUE: Switch returns to center position (red flagged). 1GS Breaker , GREEN light is

OFF, RED light is ON.

________*

15. Adjust kVARS The Operator adjust DG2 kVARS so that they are slightly positive (~200 kVARS) using DIESEL GEN 2 VOLTAGE REGULATOR

switch. (100 - 300 KVARs)

CUE: DG2 kVARS reads 40 kVARS

CUE: DG2 kVARS reads 200 kVARS

_________

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 107 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer Performance Checklist Standards Initials 16. Bkr 1FS Pull-To-Lock.

Verify switch for 1FS in PULL-TO-LOCK (PTL)

CUE: 1FS Breaker is still tagged

_________

17. Lower DG2 Load Reduce load on DG2 to 1000 KW using DIESEL GEN 2 GOVERNOR switch.

CUE: DG2 load is 2200 KW

CUE: DG2 load is 1000 KW

_________

18. Place SYNCH SWITCH to OFF Place SYNCH SWITCH 1GS to OFF

CUE: SYNCH SWITCH is in OFF

_________

19. DG2 Cooldown After engine has cooled and cylinder exhaust temperature have dropped (~5 minutes),

remove DG2 from services per 2.2.20.1.

CUE: Five minutes have elapsed.

CUE: Station Operator reports engine temperatures are cooling down.

_________

20. Lower DG2 load (2.2.20.1)

Lower DG2 load to 400 kW and 1000 kW CUE: DG2 load is 600 kW

CUE: 15 minutes have elapsed.

_________

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 108 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer Performance Checklist Standards Initials 21. Lower to 400 KW Lower DG2 load to 400 KW

CUE: DG2 load is 400 kW

_________

22. Lower kVARs Reduce DG2 kVARs as low as possible.

CUE: DG2 kVARs is 50 KVA

_________

23. Open EG2 Open DIESEL GEN 2 BKR EG2

CUE: BKR EG2 is NORMAL AFTER TRIP (green flagged). Green light is ON. Red

light is OFF.

________*

24. Inform CRS Inform CRS that the Emergency Transformer is carrying 4160 V Bus 1G.

CUE: CRS acknowledges. This JPM is complete. (Stop JPM at this point even

if candidate continues.)

_________

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 109 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer ATTACHMENT 1 SIMULATOR SET-UP A. Materials required None B. Initialize the Simulator in any at power IC (IC-18, 19 or 20 suggested)

Batch File name - none.

C. Change the Simulator conditions fr om those of the IC as follows:

1. Triggers Number File Name Description None 2. Malfunctions Number Title Trigger TD Severity Ramp Initial None

3. Remotes Number Title Trigger TD Value Ramp None 4. Overrides Instrument Tag Trigger TD Value Ramp None Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 110 of 149 Job Performance Measure for Operations Revision 05

Task Number: 245056G0101 Transfer of 4160V Bus 1G from DG2 to Emergency Transformer

5. Panel Set-up (suggested. Any setup is a llowed that supports performance of the bus transfer)

a. Place Bkr 1FS & 1GB in PTL and place Danger Tag on C/S

b. Place 2nd SW pump B in service

c. Place B RHR loop in Suppression Pool Cooling using Div 2 power sources

d. Place Bkr 1GS to NORMAL AFTER TRIP

e. At DG2 local panel, depress & re lease EMERGENCY to NORMAL RESET pushbutton.

f. At DG2 local panel, place DROOP PARALLEL switch in PARALLEL.

Note: If this JPM is to be performed more than once, snap the simu lator into an IC after the panel setup is complete.

Nebraska Public Power District SKL034-21-31 (2641) Cooper Nuclear Station Page 111 of 12 Job Performance Measure for Operations Revision 05 ATTACHMENT 2 Directions to Trainee:

When I tell you to begin, you are to perform the required actions to transfer 4160V bus 1G from DG2 to the Emergency Transformer.

Before you start, I will stat e the general plant conditions, the Initiating Cues, and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

General Conditions:

1. DG2 is supplying 4160 VAC bus 1G. 2. The Emergency Transformer is available. 3. Breaker 1GB has failed.

Initiating Cues:

The Control Room Supervisor dire cts you to perform transfer of 4160V bus 1G from DG2 to the Emergency Transformer. Inform Control Room Supervisor when 4160V bus 1G is being carried by the Emergency Transformer.

Nebraska Public Power District SKL034-30-51 (16531) Cooper Nuclear Station Page 112 of 5 Job Performance Measure for Operations Revision 01

Task Number: 200363G0501 Install EOP PTMs 57, 58, 59 and 60 Trainee: Examiner:

Pass: Fail:

Examiner Signature:

Date:

Additional Program Information:

1) Appropriate Performance Locations: Simulator

2) Appropriate Trainee Level: SO / RO / SRO

3. Evaluation Method:

Simulate Perform 4. Performance Time: 10 minutes

5. NRC K/A 295037 EA1.11 (3.5/3.6),

Directions to Examiner:

1. This JPM evaluates the trainee's ability to Install the EOP PTMs that bypass the low level group 1 isolation during an ATWAS. 2. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in the space, if desired, by the examiner. 3. Give the trainee his copy of the Directions to the Trainee (Attachment 1) when ready to start the JPM. 4. Brief the trainee and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to install EOP PTMs 57, 58, 59 and 60 to bypass the low level group 1 isolation. Before you start, I will state the general plant conditions, the Initiating Cues and answer any questions you may have.

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

====================

=========================

Nebraska Public Power District SKL034-30-51 (16531) Cooper Nuclear Station Page 113 of 5 Job Performance Measure for Operations Revision 01

Task Number: 200363G0501 Install EOP PTMs 57, 58, 59 and 60 General Conditions:

23. An ATWAS has occurred.

2. The MSIVs are open.

General

References:

1. EMERGENCY OPERATING PROCEDURE 5.8.20.

General Tools and Equipment:

1. Safety Glasses

2. Electrical Safety Equipment

Special Conditions, References, Tools, Equipment:

1. Critical checks denoted by "*."

Task Standards:

4. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The CRS directs you to bypass the low level MSIV isolation per 5.8.20 and to inform him when it is complete.

Nebraska Public Power District SKL034-30-51 (16531) Cooper Nuclear Station Page 114 of 5 Job Performance Measure for Operations Revision 01

Task Number: 200363G0501 Install EOP PTMs 57, 58, 59 and 60 Performance Checklist Standards Initials 3. Obtain a copy of EOP 5.8.20.

Current revision of EOP 5.8.20 is obtained.

4. Verifies the MSIVs are OPEN. MSIV position is verified.

CUE: All MSIV red position indicating lights are lit and the green lights are extinguished.

5. Ensure following RR sample valves CLOSED.

Ensure following valves closed (PNL 9-4) :

RR-AO-740, OUTBD ISOL VLV and RR-AO-

741, IND ISOL VLV .

CUE:RR-AO-740, OUTBD ISOL VLV and RR-AO-741, IND ISOL VLV GREEN lights

ON RED lights OFF.

Caution: If the student fails to put on safety glasses prior to installing the PTMs the JPM cannot proceed. If the JPM is being used for e valuation purposes the JPM is concluded at that point and marked unsat.

6. Puts on required safety equipment.

As a minimum safety glass are worn during the performance of this task.

7. Install EOP PTM Number 57 by jumpering between

Terminals DD1 and DD2 (BAY-1, PNL 9-15).

EOP PTM Number 57 installed.

CUE: Jumper is installed.

8. Install EOP PTM Number 58 by jumpering between

Terminals BB1 and BB2 (BAY-3, PNL 9-15).

EOP PTM Number 58 installed.

CUE: Jumper is installed.

9. Install EOP PTM Number 59 by jumpering between

Terminals DD1 and DD2 (BAY-1, PNL 9-17).

EOP PTM Number 59 installed.

CUE: Jumper is installed.

10. Install EOP PTM Number 60 by jumpering between

Terminals BB1 and BB2 (BAY-3, PNL 9-17).

EOP PTM Number 60 installed.

CUE: Jumper is installed.

Nebraska Public Power District SKL034-30-51 (16531) Cooper Nuclear Station Page 115 of 5 Job Performance Measure for Operations Revision 01

Task Number: 200363G0501 Install EOP PTMs 57, 58, 59 and 60 Performance Checklist Standards Initials 11. Informs the CRS that the low level MSIV isolation is bypassed per 5.8.20.

CRS is informed.

CUE: As the Control Room Supervisor acknowledge the report.

Nebraska Public Power District SKL034-30-51 (16531) Cooper Nuclear Station Page 116 of 4 Job Performance Measure for Operations Revision 01 ATTACHMENT 1

When I tell you to begin, you are to install EOP PTMs 57, 58, 59 and 60 to bypass the low level group 1 isolation. Before you start, I will state the general plant conditions, the Initiating Cues and answer any questions you may have.

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

General Conditions:

1. An ATWAS has occurred.

2. The MSIVs are open.

Initiating Cues:

The CRS directs you to bypass the low level MSIV isolation per 5.8.20 and to inform him when it is complete.

Nebraska Public Power District SKL034-22-02 (36407) Cooper Nuclear Station Revision 00 Job Performance Measure Pa ge 117 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:208018C0101

==========================

================

=

Task Title: Align REC after REC isolation on Low Pressure

==========================

================

=

Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: CR/SIM

2. Appropriate Trainee Level: RO/SRO

3. Evaluation Method:

Simulate Perform 4. Performance Time: 10 minutes

5. NRC K/A 295018; AA1.03 (3.3/3.4)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to Restore REC after REC isolation on Low Pressure. 2. If this JPM is performed on the Simulator, only the cues preceded by "#" should be given. 3. All blanks must be filled out with either initials or an "NP" for "not performed", an explanation may also be written in the space, if desired, by the examiner.

Directions to Trainee:

When I tell you to begin, you are to restore REC flow for Drywell Cooling after REC isolation on Low Pressu re, per the Hardcard.

When simulating, physically point to any meters, gauges, recorders and controls you

would be using. State the position of controls as you would have manipulated them to restore REC flow for Drywell Cooling after REC isolation on Low Pressure.

==========================

================

=

General Conditions:

1. The Reactor was scrammed due to loss of REC per 5.2REC.

2. REC Isolation was due to REC A ugmented Radwaste Supply pipe break down stream of REC-MO-1329, AUGMENTED RADWASTE SUPPLY 3. The REC pipe break has been isolated.

Nebraska Public Power District SKL034-22-02 (36407) Cooper Nuclear Station Revision 00 Job Performance Measure Pa ge 118 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:208018C0101

==========================

================

=

Task Title: Align REC after REC isolation on Low Pressure

==========================

================

=

Nebraska Public Power District SKL034-22-02 (36407) Cooper Nuclear Station Revision 00 Job Performance Measure Pa ge 119 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:208018C0101

==========================

================

=

Task Title: Align REC after REC isolation on Low Pressure

==========================

================

=

General

References:

SOP 2.2.65.1

General Tools and Equipment:

None Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1.

2. Critical checks denoted by "*".

3. Simulator cues denoted by "#".

4. Faulted steps denoted by "". Task Standards:

5. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

You are the Balance of Plant Operator. The CRS has directed you restore REC after REC isolation on Low Pressure

Inform the CRS when REC is restored for Drywell Cooling

NOTE: Tell Trainee to begin. Place Simulator in RUN Nebraska Public Power District SKL034-22-02 (36407) Cooper Nuclear Station Revision 00 Job Performance Measure Pa ge 120 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:208018C0101

==========================

================

=

Task Title: Align REC after REC isolation on Low Pressure

==========================

================

=

Performance Checklist Standards Initials 1. Obtain copy of SOP 2.2.65.1 The operator obtains a c opy of SOP 2.2.65.1 or Hard Card.

CUE: None.

_______ 2. Determine cause of REC isolation Ensure low pressure isolation not due to leakage or leak isolated.

CUE: REC piping break has been repaired.

_______* 3. Verify two REC pumps in Operation Ensure two REC pumps are running.

CUE: REC Pumps B and D are in service.

________*

4. Verify REC critical loop supplied.

Ensure one of following valves are OPEN:

REC-MO-711, NORTH CRITICAL LOOP

SUPPLY.

Or REC-MO-714, SOUTH CRITICAL LOOP

SUPPLY.

CUE: REC-MO-711, NORTH CRITICAL LOOP SUPPLY and REC-MO-714, SOUTH CRITICAL LOOP SUPPLY

are OPEN _______*

Nebraska Public Power District SKL034-22-02 (36407) Cooper Nuclear Station Revision 00 Job Performance Measure Pa ge 121 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:208018C0101

==========================

================

=

Task Title: Align REC after REC isolation on Low Pressure

==========================

================

=

Performance Checklist Standards Initials 5. Checking Drywell Temperature If drywell temperature 260°F on PC-TI-505A through PC-TI-505E, place DRYWELL REC ISOL

VALVE CONTROL switch to OPEN.

CUE: PC-TI-505A through PC-TI-505E reading 253°F.

_______* 6. Throttle open REC HX outlet valve Throttle open REC HX outlet valve for a HX that was in service, as necessary, while maintaining

REC CRIT LOOP SUPPLY PRESS in green

band.

REC-MO-712, HX A OUTLET VLV.

REC-MO-713, HX B OUTLET VLV.

CUE: REC-MO-712, HX A OUTLET VLV is open. _______ 7. Start third REC pump Start third REC pump.

CUE: REC Pump C is in service

_______* 8. Throttle open REC HX outlet

valve Throttle open REC HX outlet valve, as necessary, to obtain following conditions:

REC CRIT LOOP SUPPLY PRESS 62 psig.

REC HEADER PRESSURE in top of green band.

CUE: REC-MO-712, HX A OUTLET VLV is open. _______*

Nebraska Public Power District SKL034-22-02 (36407) Cooper Nuclear Station Revision 00 Job Performance Measure Pa ge 122 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:208018C0101

==========================

================

=

Task Title: Align REC after REC isolation on Low Pressure

==========================

================

=

Performance Checklist Standards Initials 9. Open REC-MO-700, NON-

CRITICAL HEADER SUPPLY. Perform following simultaneously:

Open REC-MO-700, NON-CRITICAL HEADER SUPPLY. Continue throttling open REC HX outlet valve, as necessary, to maintain REC HEADER

PRESSURE in green band.

CUE: REC-MO-700, NON-CRITICAL HEADER SUPPLY is open.

_______* 10. Ensure REC HX outlet valve

full open Ensure REC HX outlet valve full open.

CUE: REC-MO-712, HX A OUTLET VLV is open. _______* 11. Open REC-AO-710, RWCU NON-REGEN HX INLET If REC-AO-710, RWCU NO N-REGEN HX INLET, not closed for leak isolation, open REC-AO-710.

CUE: REC-MO-712, HX A OUTLET VLV is open. _______* 12. Verify REC-MO-1329, AUGMENTED RADWASTE SUPPLY is

closed. If REC-MO-1329, AUGMENTED RADWASTE SUPPLY, not closed for leak isolation and cooling

desired, open REC-MO-1329.

CUE: REC-MO-1329, AUGMENTED RADWASTE SUPPLY, is closed.

_______* 13. DRYWELL REC ISOL VALVE CONTROL switch to

AUTO Place DRYWELL REC ISOL VALVE CONTROL switch to AUTO.

CUE: REC-MO-712, HX A OUTLET VLV is open. _______*

Nebraska Public Power District SKL034-22-02 (36407) Cooper Nuclear Station Revision 00 Job Performance Measure Pa ge 123 of 149 JOB PERFORMANCE MEASURE FOR OPERATIONS Task No.:208018C0101

==========================

================

=

Task Title: Align REC after REC isolation on Low Pressure

==========================

================

=

Performance Checklist Standards Initials 14. Notify CRS.

Notify CRS that REC is restored for Drywell Cooling

CUE: Respond as the CRS and acknowledge the report.

SKL034-22-02 (36407) Page 124 of 149

Revision 00

ATTACHMENT 1 SIMULATOR SET-UP A. Materials Required

SOP 2.2.65.1

B. Initialize the Simulator in IC-20 or any IC that will support REC isolation.

C. Change the simulator conditions as follows:

1. Perform Mitigating Scram Actions.

2. Close the in service heat exchan ger outlet valve until the REC system isolates on low pressure.

Close REC-MO-1329, AUGMENTED RADWASTE SUPPLY

3. Place simulator in freeze.

Note: If this JPM is to be per formed more than once, snap the simulator into an available IC after the panel setup is complete.

SKL034-22-02 (36407) Page 125 of 149

Revision 00

ATTACHMENT 2 Directions to Trainee:

When I tell you to begin, you are to restore REC flow for Drywell Cooling after REC isolation on Low Pressu re, per the Hardcard.

When simulating, physically point to any meters, gauges, recorders and controls you

would be using. State the position of controls as you would have manipulated them to restore REC flow for Drywell Cooling after REC isolation on Low Pressure.

General Conditions:

1. The Reactor was scrammed due to loss of REC per 5.2REC.

2. REC Isolation was due to REC A ugmented Radwaste Supply pipe break down stream of REC-MO-1329, AUGMENTED RADWASTE SUPPLY 3. The REC pipe break has been isolated.

Initiating Cues:

You are the Balance of Plant Operator. The CRS has directed you restore REC after REC isolation on Low Pressure

Inform the CRS when REC is re stored for Drywell Cooling.

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 126 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Time Started: ____________ Time Finished: _____________

THIS IS AN ALTERNATE PATH JPM Additional Program Information:

1. Appropriate Performance Locations: CR / SIM

2. Appropriate Trainee level: RO / SRO

3. Evaluation Method:

Simulate Perform 4. Performance Time: 15 minutes

5. NRC K/A 261000 A4.03 (3.0/3.0)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to manipulate the SGT contro ls in order to start SGT in support of HPCI operation. 2. If this JPM is performed on the Simulator, only the cues preceded by "#" should be given. 3. All blanks must be filled out with either initials or an "NP" for "not performed"; an explanation may also be written in t he space if desired by the examiner. 4. Give the trainee his copy of the Directions to the Trainee (Attachment 2) when ready to start the JPM. 5. Brief the trainee, place the simula tor in run, and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to start the SGT system to suppo rt HPCI operation. Before you start, I will state the general plant conditions, the Initiating Cues and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any meters, gauges, recorders and controls you would be using. State the position of controls as you w ould have manipulated them in order to complete the assigned task.

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 127 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

If being performed in the Simulator:

During task performance, state the actions you ar e taking, e.g.: repositioning controls and observing instrumentation.

General Conditions:

1. The Standby Gas Treatment System is required to support HPCI operation.

General

References:

1. Procedure 2.2.73.

General Tools and Equipment:

1. None Special Conditions, References, Tools, Equipment:

1. Simulator Setup: See Attachment 1.

2. Critical checks denoted by "*".

3. Simulator cues denoted by "#".

Task Standards:

1. 100% of critical elements su ccessfully completed without error. 2. 100% of safety and radi ological work practices.

Initiating Cue(s):

The Control Room Supervisor directs you to start SGT to support HPCI operation. Inform the CRS when SGT is running to support HPCI.

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 128 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

Performance Checklist Standards Initials 1. Obtains the current revision of Procedure

2.2.73. Current revision of 2.2.73 is obtained. _______ 2. Determine the preferred SGT train.

SGT train 1A is determined to be the preferred train. _______ 3. Start EF-R-1E, SGT A EXHAUST FAN.

EF-R-1E, SGT A EXHAUST FAN switch is placed to RUN.

CUE: SGT Fan Red running light is ON and the Green light is OFF

_______* 4. Verifies the inlet and discharge valves

OPEN. Position of SGT-AO-249, SGT A INLET and SGT-AO-251, SGT A DISCHARG E are checked.

CUE: SGT-AO-249, SGT A INLET RED light is On and the GREEN light is OFF.

SGT-AO-251, SGT A DI SCHARGE red light is ON and the GREEN light is OFF.

_______ 5. Verifies SGT-DPIC-546 is in Manual.

SGT-DPIC-546 is verified in Manual.

CUE: SGT-DPIC-546 is in Manual.

_______ 6. Toggles SGT-DPIC-546 until Parameter V

is displayed. D pushbutton is depressed until parameter V is displayed.

CUE: Parameter V is displayed.

_______*

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 129 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

Performance Checklist Standards Initials 7. Adjusts SGT-DPIC-546 to ensure 800 CFM SGT-DPIC-546 is adjusted to obtain 800 scfm on SGT-FI-545, SGT DISCHARGE HEADER FLOW.

CUE: SGT-FI-545 indicates 900 CFM.

_______* 8. Checks High Moisture is clear. Checks that Annunciator K-1/A-2 "SGT A HI Moisture".

CUE: Annunciator is in alarm.

_______ 9. Checks Annunciator K-1/A-2 "SGT A HI

Moisture" Checks Annunciator K-1/A-2 "SGT A HI Moisture" and informs CRS of Alarm

CUE: CRS acknowledges the report and directs A SBGT be secured and B SBGT train started to support HPCI operation, alarm card actions will not be

performed due to not emergency condition.

_______ 10. Determines Reactor Building HV System

Operation Ensure Reactor Building H&V System running and maintaining Reactor Building pressure at -0.25" wg.

CUE: Reactor Building pressure at -0.3" wg..

_______ 11. Verifies SGT-DPIC-546 is in Manual.

SGT-DPIC-546 is verified in Manual.

CUE: SGT-DPIC-546 is in Manual.

_______

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 130 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

Performance Checklist Standards Initials 12. Toggles SGT-DPIC-546 until Parameter V is displayed. D pushbutton is depressed until parameter V is displayed.

CUE: Parameter V is displayed.

_______ 13. Adjusts SGT-DPIC-546 to ensure ~ 100

CFM SGT-DPIC-546 is adjusted to obtain ~ 100 scfm on SGT-FI-545, SGT DISCHARGE HEADER FLOW.

CUE: SGT-FI-545 indicates 100 CFM.

_______* 14. Check SGT heaters Verifies SGT heaters are off.

CUE: SGT heaters GREEN lig hts ON, RED light OFF

_______ 15. Stop EF-R-1E, SGT A EXHAUST FAN.

EF-R-1E, SGT A EXHAUST FAN switch is placed to AUTO.

CUE: SGT Fan Red running light is OFF and the Green light is ON

_______* 16. Verifies the inlet and discharge valves

CLOSED. Position of SGT-AO-249, SGT A INLET and SGT-AO-251, SGT A DISCHARG E are checked.

CUE: SGT-AO-249, SGT A INLET RED light is OFF and the GREEN light is ON.

SGT-AO-251, SGT A DI SCHARGE red light is OFF and the GREEN light is ON.

_______

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 131 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

Performance Checklist Standards Initials 17. Verifies SGT-AO-271, SGT B DILUTION AIR, in AUTO Ensure SGT-AO-271, SGT B DILUTION AIR, in AUTO and valve closed.

CUE: SGT-AO-271, SGT B DILU TION AIR, in AUTO and valve RED light is OFF and the GREEN

light is ON.

_______ 18. Start EF-R-1F, SGT B EXHAUST FAN.

EF-R-1F, SGT B EXHAUST FAN switch is placed to RUN.

CUE: SGT Fan Red running light is ON and the Green light is OFF

_______* 19. Verifies the inlet and discharge valves

OPEN. Position of SGT-AO-250, SGT B INLET and SGT-AO-252, SGT B DISCHARG E are checked.

CUE: SGT-AO-250, SGT A INLET RED light is On and the GREEN light is OFF.

SGT-AO-252, SGT A DI SCHARGE red light is ON and the GREEN light is OFF.

_______ 20. Verifies SGT-DPIC-546 is in Manual.

SGT-DPIC-546 is verified in Manual.

CUE: SGT-DPIC-546 is in Manual.

_______ 21. Toggles SGT-DPIC-546 until Parameter V

is displayed. D pushbutton is depressed until parameter V is displayed.

CUE: Parameter V is displayed.

_______*

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 132 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

Performance Checklist Standards Initials 22. Adjusts SGT-DPIC-546 to ensure 800 CFM SGT-DPIC-546 is adjusted to obtain 800 scfm on SGT-FI-545, SGT DISCHARGE HEADER FLOW.

CUE: SGT-FI-545 indicates 900 CFM.

_______* 23. Ensures High Moisture is clear.

Ensures that Annunciator K-2/A-2 "SGT B HI Moisture" is clear.

CUE: Annunciator is clear.

_______ 24. Informs CRS that the task is complete. CRS is informed.

CUE: Acknowledge the report and inform the candidate that the JPM is complete.

_______

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 133 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

ATTACHMENT 1 SIMULATOR SET-UP A. Materials Required

None B. Initialize the Simulator to a full power IC.

Batch File Name - none.

C. Change the Simulator conditions fr om those of the IC as follows:

1. Triggers

Number Description 1 ZAOSGTFI545 >0.13 Ramps moisture reading when SBGT flow greater than 500 cfm 2. Malfunctions Number Title Trigger TD Severity Ramp Initial none

3. Remotes Number Title Trigger Value Ramp None 4. Overrides Instrument Tag Trigger TD Value Ramp 18A2M04 0 TO 100% SGT A

CARBON FILTER INLET RH 1 30 sec 53.335830 sec 18A2M05 0 TO 100% SGT A HI-EFF FILTER RH INDICATOR 1 30 sec 53.335830 sec

Nebraska Public Power Dis trict SKL034-22-01(36406) Cooper Nuclear Station Page 134 of 12 Job Performance Measure for Operations Revision 00 Task No.: 261003O0101 Task Title:

SGT SYSTEM SUPPORT FOR HPCI OPERATIONS (Alternate Path)

Instrument Tag Trigger TD Value Ramp K-1 A-02 SGT A MOISTURE HIGH 1 58 sec OFF

5. Panel Setup

a. Ensure that SGT train 1A is the preferred SGT train.

Setup for the Exam:

a) Initialize the simulator in any power IC.

Note: If this JPM is to be performed more than once, snap the simu lator into an IC after the panel setup is complete.

Nebraska Public Power District SKL034-22-01 (36406) Cooper Nuclear Station Page 12 of 12 Job Performance Measure for Operations Revision 00 ATTACHMENT 2 Directions to Trainee:

When I tell you to begin, you are to start the SGT system to support HCI operation.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation.

General Conditions:

1. The Standby Gas Treatment System is required to support HPCI operation.

Initiating Cues:

The Control Room Supervisor directs you to start SGT to support HPCI operation. Inform the CRS when SGT is running to support HPCI.

Nebraska Public Power District SKL034-10-95 Cooper Nuclear Station Course Type 7456 Job Performance Measure for Operations Revision 03 136 of 149

Task No.: 200134I0504

=============================================================== Task Title: Respond to No Break Power Panel Failure (Control Bldg. Actions) (Alternate Path) ==============================================================

= Trainee: Examiner:

Pass Fail Examiner Signature: Date: THIS IS AN ALTERNATE PATH JPM Additional Program Information:

27. Appropriate Performance Locations: Plant

28. Appropriate Trainee Level: SO / RO / SRO

29. Evaluation Method:

Simulate 30. Performance Time: 25 minutes

31. NRC K/A: 262002 K4.01(3.4/3.4)

Directions to Examiner:

NOTE: This is an Alternate Path JPM. The alternate source supplying load will not work and the manual bypass switch must be used.

24. This JPM evaluates the trainee's ability to respond to a no-break power panel failure 2. All blanks must be filled out with either initials or an A NP@ for A not performed

@; an explanation may also be written in the space, if desired, by the examiner. 3. Give the trainee his copy of the Directions to the Trainee (Attachment 1) when ready to start the JPM. 4. Brief the trainee and tell the trainee to begin.

Nebraska Public Power District SKL034-10-95 Cooper Nuclear Station Course Type 7456 Job Performance Measure for Operations Revision 03 137 of 149

Task No.: 200134I0504

=============================================================== Task Title: Respond to No Break Power Panel Failure (Control Bldg. Actions) (Alternate Path) ==============================================================

= Directions to Trainee:

When I tell you to begin you are to perform the assigned Control Building Operator

=s actions to respond to a no break power panel failure. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

=========================================================

General Conditions:

1. The plant has experienced a no break power panel failure. 2. The Rx has scrammed. 3. An attempt to transfer NBPP to MCC-R by placing NBPP PWR TRANSFER switch to MCC-R has failed. 4. The electricians have determined that the fault is not in the NBPP itself.

5. Both switches have been placed to ALT at the 120v AC supplies for the gaitronics.

6. Control Room Operators have performed actions 4.1 through 4.3.11 of 5.3NBPP.

General

References:

1. 5.3NBPP (NO BREAK POWER FAILURE)

General Tools and Equipment:

1) Key for access to Control Building 903' doors.

Special Conditions, References, Tools, Equipment:

1. Critical checks denoted by "*".

Task Standards:

Nebraska Public Power District SKL034-10-95 Cooper Nuclear Station Course Type 7456 Job Performance Measure for Operations Revision 03 138 of 149

Task No.: 200134I0504

=============================================================== Task Title: Respond to No Break Power Panel Failure (Control Bldg. Actions) (Alternate Path) ==============================================================

= 2. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and ra diological work practices.

Initiating Cue(s):

You have been assigned to carry out actions for a no break power panel failure in accordance with 5.3NBPP. The Control Room Supervisor (CRS) directs you to perform all the necessary Control Building Operator

=s actions for restoring power from the Alternate Supply (MCC-R). Notify the CRS when the NBPP is energized.

Nebraska Public Power District SKL034-10-95 Cooper Nuclear Station Course Type 7456 Job Performance Measure for Operations Revision 03 139 of 149

Task No.: 200134I0504

=============================================================== Task Title: Respond to No Break Power Panel Failure (Control Bldg. Actions) (Alternate Path) ==============================================================

= Performance Checklist Standard Initials 3. Obtain a copy of 5.3NBPP Obtain a copy of 5.3NBPP, NO BREAK POWER FAILURE

__________ d. Ensure MCC-R FEED TO NBPP is in ON.

Ensure EE-DSC-NBPP(AC), MCC-R FEED TO NBPP TRANSFMR (Cable Spreading near NBPP), is in ON.

CUE: Indicate the handle is in the UP position.

__________* e. Contact the Rx Building Operator.

Contacts the Reactor Building Operator to ensure that MCC-R, Breaker 2B, NO BREAK AC POWER SUPPLY, is closed and reset.

CUE: Respond as the Rx Bldg Operator, that MCC-R, Breaker 2B, NO BREAK AC POWER SUPPLY, is closed and reset.

_________

_* f. Open breaker At Inverter A, open INVERTER OUTPUT breaker. CUE: Indicate the handle is in the DOWN position.

__________* 1. Ensure breaker is closed. At Inverter A, ensure SUPPLY TO NBPP breaker is closed.

CUE: Indicate the handle is in the UP position.

__________

Nebraska Public Power District SKL034-10-95 Cooper Nuclear Station Course Type 7456 Job Performance Measure for Operations Revision 03 140 of 149

Task No.: 200134I0504

=============================================================== Task Title: Respond to No Break Power Panel Failure (Control Bldg. Actions) (Alternate Path) ==============================================================

= Performance Checklist Standard Initials 2. Ensure breaker is closed. At Inverter A, ensure ALTERNATE AC INPUT TO STATIC SWITCH breaker is closed. CUE: Indicate the handle is in the UP position.

__________ 3. Depress button.

At Inverter A, depress ALTERNATE SOURCE SUPPLYING LOAD button.

CUE: The red ALT SOURCE SUPPLYING LOAD light is off. (NBPP is still de-energized)

_________

_ g. Place MAN BP SW to ALT SOURCE TO LOAD. Place MANUAL BYPASS SWITCH to ALTERNATE SOURCE TO LOAD.

CUE: Point to ALTERNATE SOURCE TO LOAD position.

__________* h. Depress ALT SOURCE SUPPLYING LOAD button.

Depress ALTERNATE SOURCE SUPPLYING LOAD button.

CUE: The red ALT SOURCE SUPPLYING LOAD light is on. (NBPP is energized)

__________* NOTE: The Gaitronics do not need to be transferred

i. Notifies CRS.

Notifies CRS that NBPP is

Nebraska Public Power District SKL034-10-95 Cooper Nuclear Station Course Type 7456 Job Performance Measure for Operations Revision 03 141 of 149

Task No.: 200134I0504

=============================================================== Task Title: Respond to No Break Power Panel Failure (Control Bldg. Actions) (Alternate Path) ==============================================================

= Performance Checklist Standard Initials energized.

CUE: As the CRS respond to the report. __________

Nebraska Public Power District SKL034-10-95 (7456) Cooper Nuclear Station Page 142 of 6 Job Performance Measure for Operations Revision 03 142 of 149 ATTACHMENT 1 Directions to Trainee:

When I tell you to begin you are to perform the assigned Control Building Operator

=s actions to respond to a no break power panel failure. Before you start, I will state the general plant conditions, the Initiating Cues, and answer any questions you may have.

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

General Conditions:

1. The plant has experienced a no break power panel failure. 2. The Rx has scrammed. 3. An attempt to transfer NBPP to MCC-R by placing NBPP PWR TRANSFER switch to MCC-R has failed. 4. The electricians have determined that the fault is not in the NBPP itself. 5. Both switches have been placed to ALT at the 120v AC supplies for the gaitronics.

6. Control Room Operators have performed ac tions 4.1 through 4.3.11 of 5.3NBPP.

Initiating Cues:

You have been assigned to carry out actions for a no break power panel

failure in accordance with 5.3NBPP. The Control Room Supervisor (CRS) directs you to perform all the necessary Control Building Operator

=s actions for restoring power from the Alternate Supply (MCC-R). Notify the CRS when the NBPP is energized.

Nebraska Public Power District SKL034-40-84 (18851) Cooper Nuclear Station Page 143 of 149 Job Performance Measure for Operations Revision 03

Task Number: 200390A0501 5.3ALT-STRATEGY, Inject Fire Protection Water to RHR Trainee: Examiner:

Pass Fail Examiner Signature: Date:

Additional Program Information:

1. Appropriate Performance Locations: In Plant

2. Appropriate Trainee Levels: RO / SRO

3. Evaluation Method: Simulate

4. Performance Time: 15 minutes

5. NRC K/A 295003.AA1.03 (4.4 / 4.4)

Directions to Examiner:

1. This JPM evaluates the trainee's ability to inject fire protection water into the RHR System during a complete loss of AC and DC power. 2. If this JPM is to be performed on the Simulator, only the cues preceded by "#" should be given. 3. All blanks must be filled out with either initials or an "NP" for "not performed," and an explanation may also be written in t he space if desired by the examiner. 4. Give the trainee his copy of the Directions to the Trainee (Attachment 1) when ready to start the JPM. 5. Brief the trainee and tell the trainee to begin.

Directions to Trainee:

When I tell you to begin, you are to perform the actions to align Fire Protection to RHR Subsystem "A", using SWBP "A" in accordance with Procedure 5.3ALT-STRATEGY. Before you start, I will state the general plant conditions, the Init iating Cues and answer any questions you may have.

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation. ALL PLANT ANNOUNCEMENTS WILL BE SIMULATED!

Nebraska Public Power District SKL034-40-84 (18851) Cooper Nuclear Station Page 144 of 149 Job Performance Measure for Operations Revision 03

Task Number: 200390A0501 5.3ALT-STRATEGY, Inject Fire Protection Water to RHR General Conditions:

1. The Plant has experience a to tal loss of A/C and D/C power. 2. Reactor Pressure is 600 psig.

3. Procedure 5.3ALT-STRATEGY, Alternate Core Cooling Mitigating Strategies, has been entered. 4. Another SO has completed the breaker ali gnments per step 1.1 Atta chment 1 of 5.3ALT-STRATEGY. 5. Fire Protection header is intact.

General

References:

1. Procedure 5.3ALT-STRATEGY

General Tools and Equipment:

1. 3" Fire Hose

2. Fire hose Wrench

Special Conditions, References, Tools, Equipment:

1. Critical checks denoted by "*."

2. Simulator cues denoted by "#." Task Standards:

1. 100% of critical elements succe ssfully completed without error. 2. 100% of safety and radiological work practices.

Initiating Cue(s):

The CRS has directed you to align Fire Prot ection Water to RHR Subsystem "A" using SWBP "A" in accordance with 5.3ALT-STRATEGY, Attach ment 1. You are to inform the CRS when Fire Protection Water is aligned to RHR.

Nebraska Public Power District SKL034-40-84 (18851) Cooper Nuclear Station Page 145 of 149 Job Performance Measure for Operations Revision 03

Task Number: 200390A0501 5.3ALT-STRATEGY, Inject Fire Protection Water to RHR Performance Checklist Standards Initials 32. Obtain procedure The Operator obtains a copy of the current revision of procedure 5.3ALT-STRATEGY

_______ NOTE - Equipment is stored C-882-N by MCC-T.

NOTE - The Operator must show that they are capable of obtaining the required equipment, but does not have to take them to the specifi ed locations, to get cr edit for the task element.

25. C-882 N, gets hose.

The Operator obtains the 3" hose.

CUE: Hose is obtained.

3. Remove existing 21/2" hose at Hose Station No.

16 The Operator removes the 21/2" hose

CUE: The hose is removed.

j. 4. C-882 N, attaches hose. The Operator attaches the 3" hose to FP-315, Hose Station No. 16.

CUE: The hose is attached.

k. 5. C-882 N, removes pipe cap.

The Operator removes the pipe cap from SW-641, GW System Supply from SWB Pump "A". (Outlet

of SWBP "A" Pump Inlet Strainer)

CUE: The pipe cap is removed.

l. 6. C-882 N, attaches hose. The Operator attaches the 3" hose to SW-641 connection.

CUE: The hose is attached.

Nebraska Public Power District SKL034-40-84 (18851) Cooper Nuclear Station Page 146 of 149 Job Performance Measure for Operations Revision 03

Task Number: 200390A0501 5.3ALT-STRATEGY, Inject Fire Protection Water to RHR Performance Checklist Standards Initials m. 7. C-882 N, ensures SW-84 is CLOSED. The Operator ensures that the SW-77, SWBP "A" Suction valve is closed.

CUE: The hand wheel has stopped moving in the clockwise direction.

_______

n. 8. C-882 N, ensures the SW-121 is CLOSED.

The Operator ensures that the SW-121, Emergency Core Flooding Tell-Tale Drain valve is

CLOSED. (SW-121 is in a contaminated area.

He can call for RP support or obtain PCs, or since

this is an Emergency Procedure, he can complete

the task and then ask for RP support.)

CUE: The hand wheel has stopped moving in the clockwise direction.

_______

o. 9. C-882 N, ensures valve is OPEN.

The Operator ensures that the SW-119 Emergency Core Flooding Supply Root valve is

OPEN. CUE: The hand wheel has stopped moving in the counter-clockwise direction.

_______* p. 10. C-882 N, ensures valve is OPEN.

The Operator ensures that the SW-120, Emergency Core Flooding Supply Shutoff valve is OPEN. CUE: The hand wheel has stopped moving in the counter-clockwise direction.

_______*

q. 11. C-882 N, ensures valve is OPEN.

The Operator ensures that the SW-641, GW System Supply from SWBP "A" is OPEN.

CUE: The valve Operator has been turned Counter Clockwise now is pointing straight up.

_______*

Nebraska Public Power District SKL034-40-84 (18851) Cooper Nuclear Station Page 147 of 149 Job Performance Measure for Operations Revision 03

Task Number: 200390A0501 5.3ALT-STRATEGY, Inject Fire Protection Water to RHR Performance Checklist Standards Initials r. 12. Slowly opens FP-315. The Operator slowly opens FP-315.

CUE: The hand wheel has stopped moving in the counter-clockwise direction and the hose is

charged. _______*

s. 13. Notifies CRS that task is completed.

The operator informs the CRS that Fire Water is aligned to the RHR System via SWBP "A".

CUE: The CRS acknowledges the report.

_______

Nebraska Public Power District SKL034-40-84 (18851) Cooper Nuclear Station Page 148 of 149 Job Performance Measure for Operations Revision 03

Task Number: None ATTACHMENT 1 Directions to Trainee:

When I tell you to begin, you are to perform the actions to align Fire Protection to RHR Subsystem "A", using SWBP "A" in accordance with Procedure 5.3ALT-STRATEGY. Before you start, I will state the general plant conditions, the Initiating Cues and answer any questions you may have.

If being simulated In-Plant or Control Room:

When simulating, physically point to any mete rs, gauges, recorders and controls you would be using. State the position of controls as you would have manipulated them in order to complete the assigned task.

If being performed in the Simulator:

During task performance, state the actions you are taking, e.g.: repos itioning controls and observing instrumentation. ALL PLANT ANNOUNCEMENTS WILL BE SIMULATED!

General Conditions:

1. The Plant has experience a to tal loss of A/C and D/C power. 2. Reactor Pressure is 600 psig.

3. Procedure 5.3ALT-STRATEGY, Alternate Core Cooling Mitigating Strategies, has been entered 4. Another SO has completed the breaker ali gnments per step 1.1 Atta chment 1 of 5.3ALT-STRATEGY. 5. Fire Protection header is intact.

Initiating Cues:

The CRS has directed you to align Fire Prot ection Water to RHR Subsystem "A" using SWBP "A" in accordance with 5.3ALT-STRATEGY, Attach ment 1. You are to inform the CRS when Fire Protection Water is aligned to RHR.

Nebraska Public Power District SKL034-40-84 (18851) Cooper Nuclear Station Page 149 of 149 Job Performance Measure for Operations Revision 03

Task Number: None

ML100880141

Text

References:

References:

References:

References:

References:

References:

References:

====================

========================

References:

References:

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

====================

========================

References:

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

==================

References:

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

====================

========================

References:

==========================

=====================

==========================

======================

==========================

=====================

==========================

======================

==========================

=====================