|
|
| Line 17: |
Line 17: |
|
| |
|
| =Text= | | =Text= |
| {{#Wiki_filter:M-663-00017 A Revision W04 Pa e 82-41 of 82-95 Penetration Seal Data Appendix: | | {{#Wiki_filter:}} |
| 82 Photos: P14151014 Fire Area A-16 (Side 1) Fire A rea A-16 (S ide 1 ) Fire Area A-8 (S i de 2) F i re A rea A-8 (S ide 2)
| |
| M-663-00017 A , Revision W04 Pa e 82-42 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P141W2486 Penetrat i on Type: F B-1 Fire Area (Side 1): A-16 Fire Area (Side 2): A-26 Loc./Eiev.: 2042'-11 M-OX Dwg: M-1 X 1938 1. Barrier Thickness: 1 2" 10. Annular Gap (smallest)
| |
| : 2" 2. Opening Size: 18"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 12"P 12. Barrier Type: F 4. Sealant Type: Ce ramic F i be r 13. Ope ni ng Sleeved or Concrete: Steel 5. Damming Side1: Boot 14. Pipe Insulated: No 6. Damming Side 2: B oot Jeff S u t er 7. Damming Con ti nuity (Acc/Rej): N I A Prepared By: 8. Boot Condition (Acc/Rej): Accept Wayne Aregood 9. Sealant Depth: Assumed per de tail Reviewed By: Walkdown Comme n ts: Sketch: FA: A*16 Sde 1 ) FA: A*26 Sldo 2 M-663-00017 A, Revision W04 Pa e 82-43 of 82-95 Penetration Seal Data Appendix:
| |
| 82 Photos: P141W2486 Fire Area A-16 (Side 1) F i re A re a A-1 6 (S i de 1 ) Fire Area A-26 (Side 2) Fire Area A-26 (S i de 2)
| |
| M-663-00017 A , Revision W04 Pa e 82-44 of 82-95 Penetration Seal Data Appendix: B2 Penetration
| |
| #: P14251083 Penetration Type: M-1 Fire Area (Side 1): A-1 6 Fire Area (Side 2): A-3 Loc./Eiev.: 2026'-0" M-OX Dwg: M-1X1421 1. Barr i er Thickness:
| |
| : 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: 5. Damming Side1: 6. Damming S i de 2: 20" 30"0 (1)24" P Foam N/A Assumed per deta i l 7. Damming Cont i nuity {Acc/Rej): Accept 8. Boot Condition (Acc/Re j): N/A 9. Sea l ant Depth: Assumed per de t a il Walkdown Comments:
| |
| : 10. Annu l ar Gap (smallest)
| |
| : 2" 11. Gap between pen: N/A 12. Barrier Type: F 13. Opening Sleeved o r Concrete: 14. Pipe Insulated: No Je ff Suter Prepared By: Wayn e Aregood Reviewed By: Stee l Slab thickn es s based o n C-OC1411. Insulation abuts bottom side of penetrat ion. Top s i de i s not insulated. Or igina l inspection document i ndicates 6" f o am depth (w sa). Sketch: F
| |
| * A-18 Slda t Fo<>"'"' L
| |
| .... ....,. ** \ P142S1083 ) FA: A-8 Side 2 M-663-00017 A, Revision W04 Pa e 82-45 of 82-95 Penetration Seal Data Appendix:
| |
| 82 Photos: P14251083 Fire Area A-16 (Side 1} Fire Area A-16 (Side 1} Fire Area A-3 (S i de 2) Fire A rea A-3 (S ide 2)
| |
| M-663-00017 A, Revision W04 Penetration Seal Data Penetration#:
| |
| P142S1086 Penetration Type: Loc./Eiev.: 2026'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants:
| |
| FB-1 12" 30"0 (1) 24" P 4. Sealant Type: Ceram ic F i ber 5. Damm i ng Side1: Boot 6. Damming Side 2: Boot 7. Damming Continu i ty (Acc/Rej): N J A 8. Boot Condition (Acc/Rej): Accept Pa e 82-46 of 82-95 Appendix:
| |
| B2 Fi r e Area (Side 1 ): A-16 Fire Area (Side 2): A-3 M-OX Dwg: M-1X1421 10. Annu l ar Gap (smallest):
| |
| 2" 11. Gap be t ween pen: N/A 12. Barrier Type: F 13. Open i ng Sleeved o r Concrete: Steel 14. Pipe Insulated: No J e ff Suter Prepared By: Wayne Areg oo d 9. Sealant Depth: Assumed per deta il Reviewed By: Walkdown Comments:
| |
| S lab th i ckne ss ba s ed on C-OC 14 1 1. Sketch: FA: A*1 6 Sid 1 P 142S 108 6 FA; A..a S l de2 M-663-000 17 A , Rev i sion W04 Pa e 82-47 of 82-95 Penetration Seal Data Appe n dix: 82 Photos: P14251086 F i re A r ea A-16 (Side 1) Fire A r ea A-16 (S i de 1) F i re Area A-3 (S i de 2) F i re Area A-3 (S id e 2)
| |
| M-663-00017 A, Revision W04 Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2035'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: 5. Damming Side1: 6. Damming Side 2: P142W1933 RB-8 36" 24"0 (1) 1 8" P Foam/R adflex N/A N/A 7. Damming Continu i ty (Acc/Rej): N/A 8. Boot Condition (Acc/Rej): Accept 9. Sealant Depth: 36.5" Radflex Walkdown Comments: Pa e 82-48 of 82-95 Appendix:
| |
| 82 Fire Area (Side 1 ): A-1 6 Fire Area (Side 2): A-10 M-OX Dwg: M-1 X 1 9 1 9 10. Annular Gap (smallest)
| |
| : 1-1/2" 11. Gap between pen: N/ A 12. Barrier Type: F R 13. Open i ng Sleeved or Concrete: Steel 14. Pipe Insulated: Y es J ef f Sute r Prepared By: Wayne Aregood Reviewed By: Barr ier th i cknes s based on drawing C-1 C 1421. 1-1/2" foam damm i ng per original inspection record and 2" s le eve extens ion w i ll produce a 36-1/2" radflex seal (ws a). Sleeve extender per FCR 1-B B I-091. Sketch: FA: A*16 Skle 1 v ( d P142W1933 (1 ,) FA: A*10 Sld*2 M-663-00017 A , Revision W04 Pa e 82-49 of 82-95 Penetration Seal Data Append i x: 82 Photos: P142W1933 Fire Area A-16 (Side 1 ) F ire Area A-16 (S ide 1) F ir e Area A-1 0 (S ide 2) F i re A rea A-1 0 (S ide 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-50 of 82-95 Penetration Seal Data Appendix: B2 Penetration
| |
| #: P143W1488 Penetration Type: FB-1 Fire Area (Side 1 ): A-5 Fire Area (Side 2): F-4 Loc./Eiev.: 2043'-0" M-OX Dwg: M-OX1907 1. Barrier Thick n ess: 48"
| |
| * 10. Annu l ar Gap (smallest)
| |
| : 2-1/2" 2. Opening Size: 18"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 12" P 12. Barr i er Type: A F 4. Sealant Type: Ceram i c F iber 13. Open i ng S l eeved or Conc r ete: Steel 5. Damming Side 1: Boo t 14. Pipe Insulated: No 6. Damming Side 2: Boot Way n e Aregood 7. Damming Conti n uity (Acc/Rej): N/A Prepared B y: 8. Boot Condition (Acc/Rej): A cc ept Jeff Suter 9. Sealant Depth: Rev i ewed By: Walkdown Comments:
| |
| * T his wall i s l ocated on the East s i de of the Aux. Bldg and interfaces with the Fuel Bldg , indirectly. Each building is i ndependent w i th a seismic gap between them re s ulting in a 48" wall thickness. The corresponding Fuel Bldg Pen. No. is P621W0224. Quer i ed (L B) QC that was i nvolved with this sea l during construct i on. QC indicated this sea l is fu ll depth ceramic fiber a nd is a separate sea l from P621W0224. Sketch: FA: A.S Slda 1 P143W14811 1 I Sl*5t'111C..u* "T""---"1.,--
| |
| ---"T P" * 'I> *, * ** -I> * (.etlAtr'ht f: l 8tre 'TV,) FA: F-4 S ldo2 M-663-000 17 A , Revision W04 Pa e 82-51 of 82-95 Penetration Seal Data Appendix: 82 Photos: P143W1488 F ire Area A-5 (Side 1) F i re Area A-5 (S ide 1) Fi r e Area F-4 (Si de 2) Fire A rea F-4 (S ide 2)
| |
| M-663-000 17 A , Revision W04 Pa e 82-52 of 82-95 Penetration Seal Data Appendix: B2 Penetration
| |
| #: P143W1489 Penetration Type: FB-1 Fire Area (Side 1): A-5 Fire A r ea (Side 2): F-4 Loc./Eiev.: 20 4 3'-0" M-OX Dwg: M-OX1907 1. Barrier Thickness: 48"
| |
| * 10. Annu l ar Gap (smallest):
| |
| 2" 2. Opening Size: 18''0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 12"P 12. Barr i e r Type: A F 4. Sea l a n t Type: Ceramic Fiber 13. Open i ng Sleeved or Concrete: Steel 5. Damm i ng Side1: Boot 14. Pipe In sulated: No 6. Damm i ng S i de 2: Boot Wayne Aregood 7. Damming Con t inu i ty (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Re j): Accept Jetf Suter 9. Sealant Depth: 48". Reviewed B y: Wa l kdown Commen t s:
| |
| * This wall is located on the East side of the Aux. Bldg and in terfaces with the Fue l Bldg , i nd ir ectly. Each building i s independent with a se i sm ic gap between them , resulting in a 48" w a ll thick ne ss. T he correspon d i ng Fue l Bldg Pen. No. i s P 62 1 W0221. Queried (L B) QC tha t was in vo l ved with this seal dur i ng construction. QC indicated this seal is fu l l depth ceramic f i ber and i s a separate seal from P621W0221. Sketch: FA: A-15 SlcSe1 P621WQ221 AP Sld&2 M-663-000 17 A , Revision W04 Pa e 82-53 of 82-95 Penetration Seal Data Appendix: 82 Photos: P143W1489 F ir e Area A-5 (Side 1) F i re Ar e a A-5 (Side 1 ) F ir e Area F-4 (S i de 2) Fire A r ea F-4 (S ide 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-54 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P145S0943 Penetration Type: F 8-1 Fire Area (Side 1 ): A-23 Fire Area (Side 2): A-29 Loc./Eiev.: 2026'-0" M-OX Dwg: M-1X1352 1. Barrier Thickness: 24" 10. Annular Gap (smallest): 1-112" 2. Opening Size: 14"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 4"P 12. Barrier Type: A F w 4. Sealant Type: Ceram ic F i ber 13. Open i ng Sleeved or Concrete: Steel 5. Damming Side1: Boot 14. Pipe Insulated:
| |
| No 6. Damming S i de 2: Boot Jeff S uter 7. Damming Con t inu i ty (Ace/Rei): N I A Prepared By: 8. Boot Condition (Acc/Rej): Accept Wayne Aregood 9. Sealant Depth: Assumed per detail Reviewed By: Walkdown Comments: Slab thickness based on C-1C1352. FB-6 lap seal applied on top s i de. Insulation does not transition through sea l based on inspection f rom bottom s i de.
| |
| * Origina l in specti.on record s indicate the i nstallat i on of the Lap Sea l per FC R 1-8 81-305 (wsa). Sketch: FA: A-23 S i de 1 P145SQS43 FA: A-29 S l de2 M-663-00017 A , Revision W04 Pa e 82-55 of 82-95 Penetration Seal Data Append i x: B2 Photos: P145S0943 Fir e Area A-23 (Side 1) F ir e Area A-23 (S ide 1) Fire A rea A-29 (Side 2) Fire Area A-29 {Si de 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-56 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P145S0944 Penetration Type: FB-1 Fire Area (Side 1): A-23 Fire Area (Side 2): A-29 Loc./Eiev.:
| |
| 2026'-0" M-OX Dwg: M-1 X1352 1. Barrier Thickness: 24" 10. Annular Gap (smallest)
| |
| : 3/4" 2. Opening Size: 14"0 11. Gap between pen: N/A 3. Penetrants:
| |
| (1)4"P 12. Barrier Type: A F w 4. Sealant Type: Ceramic Fiber 13. Opening Sleeved or Concrete: Steel 5. Damming Side1: Bo ot 14. Pipe Insulated: No 6. Damming Side 2: Boo t Je ff Suter 7. Damming Con tinuity (A cc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej):
| |
| Accept Wayne Aregood 9. Sealant Depth: Assumed per deta i l Reviewed By: Walkdown Comments: Slab thickness based on C-1C1352.
| |
| Topside of penetration i s provided with an FB-6 1ap seal , though i t appears i nsu l ation does not transition thr oug h seal. Original inspection records ind i cate the i nstallation of the L ap Sea l per FCR 1-881-305 (wsa). Sketch: FA: A-23 1 P14SS0944 FA: A-29 Sde2 M-663-00017 A, Revision W04 Pa e 82-57 of 82-95 Penetration Seal Data Appe n d i x: 82 Photos: P14550944 F i re A r ea A-23 (S i de 1) F i re A rea A-23 (S ide 1) Fire A r ea A-29 (Side 2) F i re Area A-2 9 (S ide 2)
| |
| M-663-00017 A, Revision W04 Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Elev.: 2026'-0" 1. Barrier Thickness: 2. Open i ng Size: 3. Penetrants:
| |
| : 4. Sealant Type: 5. Damming S i de1: P14550946 FB-1 24" 14"0 (1)4" P Ceram i c Fiber Boot 6. Damming Side 2: Boot 7. Damming Continuity (Acc/Rej): N/A 8. Boot Conditio n (Acc/Rej): Accept Pa e 82-58 of 82-95 Appendix:
| |
| B2 Fire Area (S i de 1): A-23 Fire Area (Side 2): A-30 M-OX Dwg: M-1X1352 10. Annular Gap (sma ll est): 2' 11. Gap between pe n: N/A 12. Barr i e r Type: A F w 1 3. Open i ng Sleeved o r Co n crete: Steel 1 4. Pipe In s u lated: No Jeff Suter Prepared By: Wayne Aregood 9. Sealant Depth: Assumed per deta i l Rev i ewed By: Walkdown Comments: Slab thickness based on C-1 C1352. Lap sea l provided on top s id e. Insulat i on does not penetr ate seal based on bottom side configura ti on. Orig i na l i nspect i on records indi cate the insta l lation of the Lap Sea l per FCR 1-BBI-305 (wsa). Sketch: FA: A-23 Side1
| |
| .... rT""(I:T""'\T""r"r"T'\
| |
| V.----J 1'1 t , ,..., (Ti p) Goo c-., ) FA: A-30 Slde2 M-663-00017 A , Revision W04 Pa e 82-59 of 82-95 Penetration Seal Data Append i x: 82 Photos: P145S0946 Fire Area A-23 (Side 1 ) F ir e Ar ea A-23 (S id e 1) Fire Area A-30 (Si de 2) Fire Area A-30 (S ide 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-60 of 82-95 Penetration Seal Data Appendix: B2 Penetration
| |
| #: P145S0947 Penetration Type: FB-1 Fire Area (Side 1 ): A-23 Fire Area (S i de 2): A-30 Loc.JEiev.: 2026'-0" M-OX Dwg: M-1X1352 1. Barrier Th i ckness: 24" 10. Annular Gap (smallest)
| |
| : 1-1/2" 2. Opening Size: 14"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1)4"P 12. Barr i e r Type: A F w 4. Sealant Type: Ceram ic Fiber 13. Opening Sleeved or Concrete: Stee l 5. Damming S i de1: Boot 14. Pipe Insu l ated: No 6. Damming S i de 2: Boot Je ff Suter 7. Damming Con t inuity (Acc/Rej): N I A Prepared By: 8. Boot Condition (Acc/Rej): Accept Wayne Aregood 9. Sea l a n t Depth: Assumed per detail Reviewed By: Walkdown Comments: Slab thickness based on C-1 C1352. F B-6 1 ap seal applied on top s i de. Insu l at i on does not transit i on through seal based on i nspection from bottom side. Orig in al inspection records i ndicate the installation of the Lap Seal per FCR 1-8 81-305 (wsa). Sketch: FA: A-23 Side 1 P14SS0947 FA: A-30 Slda2 M-663-00017 A , Revision W04 Pa e 82-61 of 82-95 Penetration Seal Data Appendix: 82 Photos: P14550947 F i re Area A-23 (S i de 1) F i re Area A-2 3 (Side 1) F i re Area A-30 (S id e 2) F i re Area A-3 0 (Side 2)
| |
| M-663-00017 A , Revision W04 Pa e 82-62 of 82-95 Penetration Seal Data Appendix: B2 Penetration
| |
| #: P145S0952 Penetration Type: FB-1 Fire Area (Side 1): A-23 F i re Area (Side 2): A-15 loc./Eiev.:
| |
| 2026'-0" M-OX Dwg: M-1X1352 1. Barrier Thickness: 24" 10. Annul ar Gap (smallest):
| |
| * 1-11/16" 2. Opening Size: 14" D 11. Gap between pen: N/A 3. Pe n etrants: (1) 4''P 12. Barrier T ype: A F w 4. Sealant Type: Ceramic F i ber 13. Ope ni ng Sleeved o r Concrete: Steel 5. Damming Side 1: Boot 14. Pipe I nsu l ated: Yes 6. Da m ming Side 2: Boot Jef f Suter 7. Damming Contin u ity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej): Accept Wayne A regood 9. Sealant Depth: Assumed per deta i l Reviewed By: Walkdown Commen t s: Slab th i ckness based on C-1 C 1352. Top side of penetration i s not fully accessible for in spection due to a box enclosure above penetration.
| |
| * Or i ginal i nspection records indicate 1-11/1 6" annular gap and the i nsta ll a tion of the Lap Seal per FCR 1-BB I-3 05 (wsa). Sketch: FA: A-23 Skle1 ( .,p) c r FA: A-15 Side2 M-663-000 1 7 A , Revision W04 Pa e 82-63 o f 82-95 Penetration Seal Data Appendix: 82 Photos: P145S0952 F ir e Area A-23 (S id e 1) F ir e Area A-23 (Side 1) F ire Area A-1 5 (S i de 2) Fire Area A-15 (S ide 2)
| |
| M-663-000 17 A , Revision W04 Pa e 82-64 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P145S0954 Penetration Type: FB-1 Fir e Area (Side 1): A-2 3 Fire A rea (Side 2): A-15 Loc./Eiev.:
| |
| 2026'-0" M-OX Dwg: M-1X 1352 1. Barrier Thickness: 24" 10. Ann ular Gap (smallest):
| |
| 3/8" 2. Opening Size: 14"0 11. Gap be t ween pen: N/A 3. Penetrants
| |
| : (1) 4''P 12. Barrier Type: A F w 4. Sealant Type: Ceramic F i ber 13. Op en i ng Sleeved o r Concrete: Steel 5. Damming Side1: Boot 14. P ipe Insulated:
| |
| Yes 6. Damm in g S ide 2: Boot Jeff Suter 7. Damming Continu i ty (Acc/Rej): N I A Prepared By: 8. Boot Cond ition (Acc/Rej): Accept Wayne Aregood 9. S ealant Depth: Assumed per detail Reviewed By: Wa l kdown Comments:
| |
| Slab thickness based on C-1 C 1352. It appears that an F B-6 deta il was utilized on the topside of penetration f or fl o oding protection o f insulation penetrat i ng sea l. O r i g i nal i nspection r ecords indicate the i nstallation of the Lap Sea l per FCR 1-B B I-305 (wsa). Sketch: F
| |
| * A*23 S i de 1 P 1 45S0954 c f) FA: A*1S Side 2 M-663-00017 A, Revision W04 Pa e 82-65 of 82-95 Penetration Seal Data Appendix: 82 Photos: P145S0954 F ire Area A-23 (S i de 1) F i re Area A-23 (S ide 1) Fire Area A-15 (Side 2) Fire Area A-1 5 (Side 2)
| |
| M-663-00017 A, Revision W04 Penetration Seal Data Penetration#:
| |
| P145W2468 Penetration Type: Loc./Eiev.: 2038'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : F B-1 36" 1 4"0 (1) 4"P 4. Sealant T ype: Ceramic F i be r 5. Damming S i de1: Bo ot 6. Damming S i de 2: Boo t 7. Damming Con tin uity (Acc/Rej): N I A 8. Boot Condition (Acc/Re j): Accept Pa e 82-66 of 82-95 Appendix:
| |
| B2 Fire Area (Side 1): A-23 F i re Area (Side 2): T-2 M-OX Dwg: M-OX 1 933 10. Annula r Gap (smallest)
| |
| : 3/4" 11. Gap between pen: N/A 12. Barr i er Type: F 13. Open in g Sleeved or Concrete: Stee l 14. Pipe Insulated: Ye s Je ff Suter Prepared By: Wayne Aregood 9. Sealant Depth: Assumed per de tail Reviewed By: Walkdown Comments: Barr i er thic k nes s ba s ed on drawing M-OX1933. Pipe i s in su lat ed through sea l. Sketch: FA: A-.:1!3 Sid 1 1 P14.5W2468 FA: T-2 Side 2 M-663-00017 A, Revision W04 Pa e 82-67 of 82-95 Penetration Seal Data Appendix:
| |
| 82 Photos: P145W2468 F i re Area A-23 (S i de 1) F i re Area A-23 (Side 1) F i re A r ea T-2 (Side 2) Fire Area T-2 (S ide 2)
| |
| M-663-00017 A , Revision W04 Penetration Seal Data Penetration
| |
| #: P145W2469 Penetration Type: Loc./Eiev.: 2 028'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : F B-1 36" 1 4"0 (1)4"P 4. Sealant Type: Ceramic F iber 5. Damming Side1: Boot 6. Damming Side 2: Boot 7. Damming Continuity (Acc/Rej): N/A 8. Boot Condition (Acc/Rej):
| |
| Accept Pa e 82-68 of 82-95 Appendix: B2 Fire Area (Side 1): A-2 3 Fire Area (Side 2): T-2 M-OX Dwg: M-O X 1933 10. Annu l ar Gap (sma ll est): 3/4" 11. Gap between pen: N/A 12. Barrier Type: F 13. Opening Sleeved o r Concrete: Steel 14. Pipe Insulated: Yes Jeff Suter Prepared By: Wayne Aregood 9. Sealant Depth: Assumed p er detail Reviewed By: Wa l kdown Comments: Barrier th i ckness based on drawing M-OX1933. Pipe i s ins u lated through sea l. Sketch: F A: A-23 S kle1 J ., .. ( 1 ) P145W2A69
| |
| -) FA: T-2 Sde2 M-663-00017 A, Revision W04 Pa e 82-69 of 82-95 Penetration Seal Data Appendix:
| |
| 82 Photos: P145W2469 Fire Area A-23 (Side 1) Fire Area A-23 (S ide 1 ) F ir e Area T-2 (S ide 2) Fire A rea T-2 (S ide 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-70 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P145W2470 Penetration Type: FB-1 Fire Area (Side 1 ): A-23 Fire Area (Side 2): T-2 Loc./Eiev.: 2028'-0" M-OX Dwg: M-OX1933 1. Barrier Thick n ess: 36" 1 0. Annu l a r Gap (sma ll est): 1-1/2" 2. Opening Size: 14"0 11. Gap between pen: N l a 3. Penetrants
| |
| : (1) 4"P 12. Ba r r ier Type: F 4. Sealant Type: Ceramic F ib er 13. Open in g Sleeved o r Concrete: Stee l 5. Damming Side1: Boot 14. Pipe Insulated:
| |
| Yes 6. Damming S i de 2: Boot Je ff Suter 7. Damming Con t inuity (Acc/Rej): N/A Prepared By: 8. Boot Condit i o n (Acc/Rej): Accept Wayne Aregood 9. Sealant Depth: Assumed per deta i l Reviewed By: Walkdow n Comments: Barrier thi ck n ess based on drawing M-OX1933. P i pe is in su l ated through sea l. Sketch: FA. A-23 Slde1 P145W2470 FA: T-2 Slde2 M-663-00017 A , Revision W04 Pa e 82-71 of 82-95 Penetration Seal Data Appendix: 82 Photos: P145W2470 Fire Area A-23 (S id e 1) Fire Area A-23 (S ide 1) Fire Area T-2 (S i de 2) F ire Area T-2 (S i de 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-72 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration#:
| |
| P145W2471 Penetration Type: F B-1 Fire Area (S i de 1): A-23 Fire Area (Side 2): T-2 Loc./Eiev.: 2028'-0" M-OX Owg: M-OX193 3 1. Barrier Thick n ess: 36" 10. Annular Gap (smallest): 1" 2. Opening Size: 14"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 4" P 12. Barrier Type: F 4. Sea l ant Type: Ceram i c F iber 13. Opening Sleeved o r Concrete: Stee l 5. Damming Side1: Boot 14. Pipe In s ul ated: Yes 6. Damming Side 2: Boot Jeff Suter 7. Damming Con t inuity (Acc/Rej): N/A Prepared By: 8. Boot Condit i on (Acc/Rej): Accept Wayne Aregood 9. Sealant Depth: Assumed per detai l Reviewed By: Wa l kdown Comments: Barr i er th ickn ess based on drawing M-OX1933. Pipe is i nsulated through sea l. Sketch: FA.: A-23 Sld 1 P145W2471 FA* T*2 Sida2 M-663-00017 A Revision W04 Pa e B2-73 of B2-95 Penetration Seal Data Ap p end i x: 82 Photos: P145W2471 Fire Area A-23 (S i de 1) F i re Area A-23 (Side 1) Fire Area T-2 (Side 2) Fire Area T-2 (S id e 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-74 of 82-95 Penetration Seal Data Append i x: B2 Penetration#:
| |
| P152W2585 Pe netration Type: FB-1 Fire Area (Side 1): A-19 F ir e Area (Side 2): A-22 Loc.J Eiev.: 2064'-1 1 M-OX Dwg: M-OX1947 1. Barrier Thickness: 12" 10. Annular Gap (smallest):
| |
| 1" 2. Opening Size: 14"D 11. Gap betw een pen: N/A 3. Penetrants
| |
| : (1)10''P 12. Barrier Type: A F 4. Sealant Type: Ceramic F i ber 13. Ope ning Sleeved or Concrete: Steel 5. Damming Side1: Boo t 14. P ipe Insulated:
| |
| No 6. Damm ing Side 2: Boo t Wayne Aregood 7. Damming Con ti nuity (Ac c/Rej): N I A Prepared By: 8. Boot Condit i on (Acc/Rej):
| |
| Accept Jeff Suter 9. Sealant Depth: Assumed Per Deta i l Rev iewed By: Walkdown Comments: Wall thickness determined by Drawing C-1 C1521. Sketch: FA: A-19 Slde' P152W2S85 to **
| |
| M-663-00017 A , Revision W04 Pa e 82-75 of 82-95 Penetration Seal Data Ap p end i x: 82 Photos: P152W2585 F i re Area A-1 9 (S i de 1 ) F i re A r ea A-19 (S ide 1) Fire Area A-22 (Si de 2) F i re Area A-22 (S id e 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-76 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P311W0839 Penetration Type: FB-1 Fire Area (Side 1): C-1 Fire Area (Side 2): CC-1 Loc./Eiev.: 1976'-0" M-OX Dwg: M-1 X3901 1. Barrier Thickness: 36" 10. Annular Gap (smallest):
| |
| 2" 2. Opening Size: 36"D 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 30" P 12. Barr ier Type: A F w 4. Sealant Type: Ceram i c Fiber 13. Opening Sleeved o r Co n crete: Steel 5. Damming Side1: Boot 14. Pipe Insulat ed: No 6. Damming Side 2: Boot Wayne Aregood 7. Damm i ng Cont in uity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej): Accept Jeff Suter 9. Sealant Depth: Assumed Per Deta i l Reviewed By: Walkdown Comments: Barrier t h ickne ss determined by Drawing C-1 C3111. Sketch: P311W0839
| |
| * r:i * .... "' a --, . a-. -. .t> tJ -.. * -** ' i #I * ' &* -o. o , * -* t>. ,... , .. . ,._ o... .. . . IJ" * * ** '/:1 I -J r ' IJ : P .. ' FA: CC-1 Sid*2 M-663-00017 A , Rev i sion W04 Pa e 82-77 of 82-95 Penetration Seal Data Appendix: 82 Photos: P311W0839 Fire Area C-1 (S id e 1) Fire Area C-1 (Side 1 ) F i re Area CC-1 (Side 2) Fire Area CC-1 (Side 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-78 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P611W0197 Penetration Type: FB-1 Fire Area (S i de 1): F-2 Fire Area (S i de 2): F-3 Loc./Eiev.: 2019'-0" M-OX Dwg: M-1X6906 1. Barrier Thickness: 12" 2. Opening Size: 16" 0 3. Penetrants
| |
| : (1) 12"P 4. Sea l a n t Type: Ceram i c Fibe r 5. Damm i ng Side1: Boot 6. Damm i ng S i de 2: Boot 7. Damming Con t inu i ty (Acc/Rej): N/A 8. Boot Condition (Acc/Rej): Accept 9. Sealant Depth: Assumed Pe r Detail Walkdown Comments: Wall thic k ne ss de t ermined by Draw i ng C-1 C6111. Sketch: FA: F-2 S1de1 P611W0197
| |
| : 10. Annular Gap (smallest): 1-1/4" 11. Gap between pen: N/A 12. Barr i er Type: F 13. Openi n g Sleeved o r Concrete: 14. Pipe Insulated:
| |
| No Wayne Aregood Prepared By: Jeff Suter Reviewed By: u . A * * '* b t> I> /J'. ,p. f1 ** . . "b * . . FA: F-3 Sldt2 Stee l M-663-000 1 7 A , Rev i sion W04 Pa e B2-79 of B2-95 Penetration Seal Data A p pend i x: 82 Photos: P611W 0 197 Fire Area F-2 (Sid e 1) Fire Area F-2 (Side 1) Fire Area F-3 (Side 2) Fire Area F-3 (Side 2)
| |
| M-663-00017 A Revision W04 Penetration Seal Data Penetration#
| |
| : P621S0153 Penetration Type: F B-1 Loc./Eiev.: 2026'-0" 1. Barrier Thickness: 2. Opening S i ze: 3. Penetrants
| |
| : 4. Sealant T ype: 5. Damming S i de1: 10" 14"0 (1) 10" P Ce ram ic F i ber Boot 6. Damming S i de 2: Bo ot 7. Damming Continuity (Acc/Rej): N I A 8. Boot Condition (Acc/Rej): A ccep t Pa e 82-80 of 82-95 Appendix:
| |
| B2 Fire Area (Side 1 ): F-5 M-OX Dwg: M-OX 6 21 1 Fire Area (S i de 2): F-3 10. Annula r Gap (smallest)
| |
| : 1" 11. Gap between pen: N I A 12. Barr i er Type: F 13. Openi n g Sleeved o r Concrete: 14. Pipe In sulated: No Wayne Aregood Prepared By: Je ff Suter w Stee l 9. Sealant Depth: Assumed Per Detail Reviewed By: Walkdown Commen t s: Sketch: F-S Side t 5*.C.Tlolol A
| |
| FA: F-3 S lde2 M-663-00017 A, Revision W04 Pa e 82-81 of 82-95 Penetration Seal Data Append i x: 82 Photos: P621S0153 F ir e Area F-5 (S i de 1) F ir e Area F-5 (Si de 1) F ire Area F-3 (Side 2) Fire A r ea F-3 (S ide 2)
| |
| M-663-000 17 A, Revision W04 Pa e 82-82 of 82-95 Penetration Seal Data Appendix:
| |
| 82 Penetration#:
| |
| P621S0156 Penetration Type: F B-1 Fire Area (Side 1): F-4 Fire Area (Side 2): F-3 loc./Eiev.: 2026'-0" M-OX Dwg: M-OX6211 1. Barrier Thickness: 1 0" 10. Annular Gap (smallest)
| |
| : 1" 2. Opening Size: 16"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 12"P 12. Barrier Type: F w 4. Sealant Type: Ceram i c F iber 13. Opening Sleeved or Concrete: Steel 5. Damming Side1: Boo t 14. Pipe In s ul ated: No 6. Damming Side 2: Boot Wayne Aregood 7. Damming Con t inuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej): Accept Jeff Suter 9. Sealant Depth: Assumed Per Detail Reviewed By: Wa l kdown Comments: Sketch: FA; F-4 Slde1 1------I P$2150156 11 10" ll. _j FA._ F-3 Slde2 M-663-00017 A, Revision W04 Pa e 82-83 of 82-95 Penetration Seal Data Appendix: 82 Photos: P621S0156 Fi r e Area F-4 (Side 1) Fire Area F-4 (S ide 1) Fire Area F-3 (S i de 2) F i re Area F-3 (S ide 2)
| |
| M-663-00017 A, Revision W04 Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2026'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Seala nt Type: 5. Damm in g Side1: P621S0157 FB-1 1 0" 1 6"0 (1) 12 .. P Ceramic F iber Boot 6. Damm in g Side 2: Boot 7. Damming Con tinuit y (Acc/Rej): N/A 8. Boot Condition (Acc/Rej): Accept Pa e 82-84 of 82-95 Appendix:
| |
| B2 Fire Area (Side 1 ): F-4 Fire Area (Side 2): F-2 M-OX Dwg: M-OX6211 10. Annular Gap (sma ll est): 1/4" 11. Gap between pen: N/A 12. Barrier Type: F w 13. Opening Sleeved o r Concrete: Steel 14. Pipe Insulated:
| |
| No Wayne Aregood Prepared By: Je ff S ute r 9. Sealant Depth: Assumed Pe r Detai l Reviewed By: Wal kd own Comments: S lab thi ckness (12") deter m i ned by C-1 C621 1. Sketch: FA: F-4 Slcle 1 P621S0157 FA: F-3 S1de2 M-663-00017 A , Revision W04 Pa e 82-85 of 82-95 Penetration Seal Data Appendix:
| |
| 82 Photos: P62150157 F i re Area F-4 (S i de 1) F i re Ar e a F-4 (S ide 1) Fi r e A rea F-2 (Side 2) Fire Area F-2 (Side 2)
| |
| M-663-000 17 A , Revision W04 Pa e 82-86 of 82-95 Penetration Seal Data Appendix: B2 Penetration
| |
| #: P621S0162 Penetrat ion Type: FB-1 Fire Area (Side 1): F-4 Fire A rea (S ide 2): F-2 Loc./Eiev.: 2026'-0" M-OX Dwg: M-OX6211 1. Barrier Thickness: 1 0" 10. Annular Gap (smallest)
| |
| : 1-1/4" 2. Open ing Size: 16"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 12"P 12. Barrier Type: F w 4. Sealan t Type: Ceramic Fiber 13. Openi ng Sleeved or Concrete: Steel 5. Damming S i de1: Boo t 14. Pipe Insulated: No 6. Damming S i de 2: Boot Wayne Aregood 7. Damming Continuity (Acc/Rej):
| |
| N/A Prepared By: 8. Boot Condition (A cc/Rej): Accept Jeff Suter 9. Sealant Depth: Assumed Per Detail Reviewed By: Walkdown Comments: Sketc h: FA: F-4 Skle 1 P621S0182 FA: F*2 Side2 M-663-00017 A , Revision W04 Pa e 82-87 of 82-95 Penetration Seal Data Appendix: 82 Photos: P621S0162 Fire Area F-4 (Side 1) F i re Area F-4 (S i de 1) F i re Area F-2 (S i de 2) F i re Area F-2 (Side 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-88 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P621W0009 Penetration Type: FB-1 Fire Area (Side 1 ): F-4 Fire Area (Side 2): F-5 Loc./Eiev.: 2 04 1 '-6" M-OX Dwg: M-O X 6908 1. Barrier Thickness: 12" 2. Opening Size: 16"0 3. Penetrants
| |
| : (1)12" P 4. Sealant Type: Ceram ic F iber 5. Damm i ng S i de1: Boot 6. Damm i ng Side 2: Boot 7. Damming Con t inuity (Acc/Rej):
| |
| N I A 8. Boot Condit i on (Acc/Rej):
| |
| Accept 9. Sealant Depth: Assumed P er Deta i l Walkdown Comments: Wall thickness (1 2") determ i ned by C-1 C621 1. Sketch: FA: Side t P62fW0009
| |
| : 10. Annular Gap (smallest): 3/4" 11. Gap between pen: N/A 12. BarrierType
| |
| : F 13. Opening Sleeved or Co n crete: 1 4. Pipe In s ul ated: No Wayne Aregood Prepared By: Jef f Suter Reviewed By: ' p
| |
| * 0 ... b -' FA: F*5 Sid 2 Stee l M-663-00017 A Revision W04 Pa e 82-89 of 82-95 Penetration Seal Data Appe n dix: 82 Photos: P621W0009 Fire Area F-4 (Side 1 ) Fi re A r ea F-4 (S ide 1) Fire Area F-5 {S i de 2) Fire Area F-5 {S ide 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-90 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P621W0017 Penetration Type: FB-1 Fire Area (Side 1): F-5 F ir e Area (Side 2): F-4 Loc./Eiev.: 2041'-6" M-OX Dwg: M-OX6908 1. Barrier Thickness: 12" 10. Annula r Gap (smallest):
| |
| 1-1/2" 2. Open ing Size: 16"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 12"P 12. Barr ier Type: F 4. Sealant Type: Ceramic F iber 13. Ope ning Sleeved or Concrete: Steel 5. Damming Side1: Boo t 14. Pipe Insulated:
| |
| No 6. Damming S ide 2: Boot Wayne Aregood 7. Damming Con t inuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej):
| |
| Accept Jeff Sute r 9. Sealant Depth: Assumed per detail Reviewed By: Walkdown Comments: Wall thickness ( 12") determined by C-1 C62 11. Sketch: FA: Slde1 Pfl21W0017 o -* . a* . , . -. '-*** tl * *F : t>, -, . .. . . . . ' FA: F-4 Sk:td M-663-00017 A , Revision W04 Pa e 82-91 of 82-95 Penetration Seal Data Appendix: 82 Photos: P 621W0017 Fire Area F-5 (Si de 1) Fire Area F-5 (S ide 1) F ire Area F-4 (S ide 2) Fire Area F-4 (Si de 2)
| |
| M-663-00017 A, Revision W04 Pa e 82-92 of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P621W0221 Penetration Type: FB-1 Fire Area (Side 1 ): A-5 Fire Area (S i de 2): F-4 Loc./Eiev.
| |
| : 2043'-0" M-OX Dwg: M-OX6901 1. Barrier Thickness:
| |
| * 48" 10. A nnular Gap (smallest)
| |
| : 2" 2. Opening Size: 1 8"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 1 2" P 12. Barr ier Type: A F 4. Sealant Type: Ceram i c Fiber 13. Ope ning Sleeved or Concrete: St e e l 5. Damming S ide1: Boot 14. Pipe Insulated:
| |
| No 6. Damming S ide 2: Boot Wayne Aregood 7. Damming Con tinuity (Ac c/Rej): N I A Prepa red By: 8. Boot Condition (Acc/Rej): A cc ep t J eff Sut er 9. Sealant Depth: 48"* Reviewed By: Walkdown Comments:
| |
| * T h is wal l i s l ocated on t he west side of t h e Fue l Bldg and in terfaces w it h th e Aux B l dg. Eac h bui l d i n g is i ndependen t w i t h a seis mi c gap between t h em. resul ti ng in a 48" wa ll th ickness. T he correspond i ng Aux B l dg Pen. No. i s P 1 43W1489. Que ri ed (LB) QC t hat was i nvolved w ith th i s sea l dur i ng co n struc ti o n. QC i n d i ca t e1 t his sea l i s full depth ce r amic f i ber a n d i s a separa t e seal from P143W 1 489. Ske tch: FA: A*!i Sld411 P621 W 0221 I) ... Loo Slde2 M-663-00017 A , Revision W04 Pa e 82-93 of 82-95 Penetration Seal Data Append i x: 82 Photos: P621W0221 F i re Area A-5 (S i de 1 ) F i re Area A-5 (S i de 1) F i re Area F-4 (Side 2) F ire A r ea F-4 (S i de 2)
| |
| M-663-00017 A Revision W04 Pa e of 82-95 Penetration Seal Data Appendix:
| |
| B2 Penetration
| |
| #: P621W0224 Penetration Type: FB-1 Fire Area (Side 1): A-5 Fire Area (Side 2): F-4 Loc.IEJev.:
| |
| 2043'-0" M.OX Owg: M-OX6901 1. Barrier Thickness:
| |
| 48"" 10. Annular Gap {smallest):
| |
| 2-1/2" 2. Opening Size: 18"D 11. Gap between pen: N/A 3. Penetrants:
| |
| (1)12"P 12. BarrierType:
| |
| A F 4. Sealant Type: Ceramic Fiber 13. Opening Sleeved or Concrete:
| |
| Steel 5. Damming Side1: Boot 14. Pipe Insulated:
| |
| No 6. Damming Side 2: Boot Wayne Aregood 7. Damming Continuity (Acc!Rej):
| |
| NIA Prepared By: 8. Boot Condition (Acc!Rej}:
| |
| Accept Jeff Suter 9. Sealant Depth: 48". Reviewed By: Walkdown Comments:
| |
| * This wall is located on the west side of the Fuel Bldg and interfaces with the Aux Bldg. Each building is independent with a seismic gap between them, resulting in a 48" wall thickness.
| |
| The corresponding Aux Bldg Pen. No. is P143W1488.
| |
| Queried {LB) QC that was involved with this seal during construction.
| |
| QC indicated this seal is full deplh ceramic fiber and is a separate seal from P143W1488.
| |
| Sketch: 1 I
| |
| ...,...---:-'1.,...----t*
| |
| {e!ii'tltl'fl(. ,"'N,.) FA: f-4 Slde2 M-663-00017 A Revision W04 Pa e 82-95 of 82-95 Penetration Seal Data Appendix: 82 Photos: P621W0224 Fire Are a A-5 (Side 1) Fire Area A-5 (Si de 1) Fire Area F-4 (S ide 2) F ir e Area F-4 (S ide 2)
| |
| Page 1 CREEK r NUCLEAR OPERATING CORPORATION M-663-00017 A Attachment 83 Fire Protection Evaluation For Penetrations That Exceed Service Temperature Limitations Rev. No. Prepared By Date Reviewed By Date W01 08/19/05 08/19/05 Wayne S Aregood Jeff Suter W06 02/14/17 Dale T. Krisman M-663-000 17 A Attachment 83 Revision W01 Table of Contents Page 2 of 8 Revision Log ...................................................................................................................................
| |
| 3 1.0 Purpose ...............................................................................................................................
| |
| 4 2.0 Scope ..................................................................................................................................
| |
| 4 3. 0 References
| |
| ..........................................................................................................................
| |
| 4 4.0 Evaluation
| |
| ...........................................................................................................................
| |
| 5 5.0 Conclusions
| |
| .........................................................................................................................
| |
| 8 Appendix 83, Penetration Seal Data .....................................................
| |
| (42 Total Pages)
| |
| M-663-00017 A Attachment 83 Revision W01 Revision Reason for Revision W01 Original Issue Page 3 of 8 Revision Log M-663-00017 A Attachment B3 Revision W01 1.0 Purpose Page 4 of 8 1.1 The purpose of this document is to evaluate existing penetration seals that are not directly bounded to the typical detail limitations established in M-663-00017.
| |
| This evaluation was conducted in effort to satisfy regulatory expectation regarding qualification and documentation of fire barrier penetration seals, as discussed in NRC Information Notice 88-04. This evaluation was conducted in accordance with the guidance of NRC Generic Letter 86-10. 2.0 Scope 2.1 The Table I penetrations in relation to the design requirements discussed in Section 5.1. 2.2 Refer to Section 7.0 of M-663-00017A for a cross reference list of penetrations within Table I that are evaluated for additional seal parameters that do not satisfy the typical detail limitations of M663-00017.
| |
| In these instances, the potential cumulative affects of multiple unbounded attributes were considered for each penetration of concern. 3.0 References 3.1 NRC Generic Letter 86-10, Implementation of Fire Protection Requirements, dated April 24, 1986 3.2 NRC Information Notice 88-04, Inadequate Qualification and Documentation of Fire Barrier Penetration Seals 3.3 10 CFR 50 Appendix R, Fire Protection Program For Nuclear Power Facilities Operating Prior To January 1, 1979 3.4 LER 87-10, Technical Specification Violations-Inoperable Fire Barriers Caused By Personnel Errors 3.5 M-663-00017, Penetration Seal Typical Details, Rev. W20 3.6 STN FP-452, Fire Barrier Penetration Seal Inspection, Rev. 4 3.7 PIR 2005-2384, Penetrations Requiring Field Work 4.0 Assumptions 4.1 It is assumed that existing penetration real materials have been installed as required by applicable typical design details and procedures.
| |
| This is an acceptable assumption based on a review of the Quality Control documentation maintained during initial penetration seal installation activities and the intrusive inspections conducted to address LER 87-10, regarding seal material depth.
| |
| M-663-00017 A Attachment B3 Revision W01 5.0 Evaluation 5.1 Assessment of Condition to Design Requirements Page 5 of 8 The Table I penetrations contain a penetrant that exceeds the service temperature of the assigned typical detail from The M-663-00017 typical detail service temperature restrictions are based on manufacturer identified seal material temperature exposure limitations.
| |
| TABLE I Penetration with Service Temperatures Exceeding Typical Detail Limitations Communicating Typical Calculated Sealant Penetration Fire Areas Service Condition Comments/Disposition:
| |
| Number Detail Temp Actual Side 1 Side 2 (oF) (Acc./Rej.)
| |
| P121S0264 A-1 A-4 RB-1 400 Ace See 5.2 for temperature limitation acceptability.
| |
| Insulation transitions through the seal protecting the Radflex from system temperatures (limitation of 206°F). P121S0265 A-1 A-4 RB-1 280 Ace See 5.2 for temperature limitation acceptability.
| |
| Topside inspection revealed that no degradation was evident. P121S0275 A-1 A-4 RB-5A 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| P121S0277 A-1 A-4 RB-1 350 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| Insulation transitions through the seal protecting the Radflex from system temperatures
| |
| *(limitation of 206°F). P122S0327 A-1 A-2 RB-5A 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| P122S0339 A-1 A-2 RB-5A 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| P131S0526 A-9 A-1 RB-5A 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| P131S0528 A-9 A-1 RM-1A 400 Ace. See 5.2 for temperature limitation acceptability.
| |
| Visual examination revealed no physical degradation.
| |
| P131S0530 A-9 A-1 RB-5A 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| P131S0531 A-9 A-1 RB-5A 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| P132S0693 A-10 A-1 RB-1 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| Topside inspection revealed that no degradation was evident.
| |
| M-663-00017 A Attachment B3 Revision WO 1 Communicating Penetration Fire Areas Number Side 1 Side 2 P133S0799 A-25 A-1 P133S0810 A-25 A-1 P134S0860 A-24 A-1 P135S0227 A-15 A-33 (2 penetrants)
| |
| P145S0952 A-23 A-15 P145S0954 A-23 A-15 P145W2468 A-23 T-2 P145W2469 A-23 T-2 P145W2470 A-23 T-2 P145W2471 A-23 T-2 Table Notes: Typical Detail R8-1 R8-5A R8-1 F8-1 F8-1 F8-1 F8-1 F8-1 F8-1 F8-1 Page 6 of 8 Calculated Sealant Service Condition Comments/Disposition:
| |
| Temp Actual _COF) (Acc./Rej.)
| |
| 350 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| Insulation transitions through the seal protecting the Radflex from system temperatures (limitation of 206°F). 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| 400 Ace 2 See 5.2 for temperature limitation acceptability.
| |
| Insulation transitions through the seal protecting the Radflex from system temperatures (limitation of 206°F). 575 Ace 1 See 5.2 for temperature limitation acceptability 575 Ace 1 &2 See 5.2 for temperature limitation acceptability Refer to Attachment 813 for as left configuration following field action necessary to address PIR 2005-2384.
| |
| 575 Ace 1 &2 See 5.2 for temperature limitation acceptability Refer to Attachment 813 for as left configuration following field action necessary to address PIR 2005-2384.
| |
| 600 Ace 1 &2 See 5.2 for temperature limitation acceptability 600 Ace 1 &2 See 5.2 for temperature limitation acceptability 600 Ace 1 &2 See 5.2 for temperature limitation acceptability 600 Ace 1 &2 See 5.2 for temperature limitation acceptability
| |
| : 1. Temperature limitations for this penetration seal applies only to the boot and silicone caulk adhesive.
| |
| Temperature limitations do not apply to the Ceramic Fiber sealant material.
| |
| : 2. Sealant condition could not be confirmed due to boot installation preventing visual inspections.
| |
| Although, topside boots are not required for R8-1 detail, topside boots have been installed in many instances.
| |
| F8-1 detail boot condition was acceptable with no evidence of degradation.
| |
| In some cases topside seal configuration was also enclosed within insulation that prevent sealant inspection, but was accessible on the bottom side to allow visual evaluation of boot. In these cases the boot did not exhibit degradation.
| |
| M-663-00017 A Attachment 83 Revision WO 1 5.2 Evaluation of Condition Page 7 of 8 Table I identifies penetration seals with temperature limitation issues where the service penetrant operates at a higher temperature than the seal design is qualified.
| |
| The majority of these penetration seals exceed temperature limitations by less than 10°F (392°F material limitation).
| |
| It is reasonable to conclude that this minor temperature variation will not affect, degrade or actually impact sealant materials.
| |
| Other penetration seals may be exposed to temperatures that appear to be significantly greater than that specified in the manufacturer's material specification data sheet and are further evaluated herein. Penetrant service temperatures are calculated during design phases of the plant and are typically determined based on operating temperatures of major system equipment.
| |
| In many instances, depending on the location of the affected penetration seal, the seal may not be exposed to the pre-determined design operating temperatures due to heat loss and actual cooler operating temperatures as distance from the major system equipment increases.
| |
| The actual system design operating temperatures may also be less than initially identified during the design phases of the plant. Another factor that could affect the penetration sealant material is whether the pipe is insulated through the enclosure.
| |
| Due to these many variables regarding system operating temperatures (service temperatures), seal configurations, and plant environments, the actual sealant conditions are best interpreted by in plant visual inspections to determine seal material acceptability.
| |
| The plant has been operating for more than 19 years and degradation caused by excessive system temperature exposures would generally be visually evident on seal materials and/or components.
| |
| If the penetration seal material (boot, damming or sealant) visually appears acceptable with no physical degradation such as discoloration, charring, excessive drying, loss of flexibility, or bond separation caused by environmental or system interactions, it can be concluded that the penetration seal is acceptable regardless of the calculated design service temperatures.
| |
| When HOSE/HOLE or Silicone Foam is used as the primary sealant, it is typically concealed by installed boots. These Elastomer based materials have relatively the same temperature limitation as the boot material.
| |
| Therefore, if no boot degradation is observed, it is reasonable to conclude that the condition of the concealed primary sealant material is acceptable.
| |
| When ceramic fiber is used as the primary sealant, only the boot material needs to be considered because ceramic fiber is not affected by temperature exposures.
| |
| When Radflex is used as the primary sealant, pipe insulation is generally provided to reduce temperature exposure, since Radflex has a very low temperature limitation (206°F). Typically, this insulation reduces contact temperature to that below the Radflex temperature limitation.
| |
| Where readily visible, Radflex was physically examined for seal degradation. Where Radflex was concealed by boots, the boot visual condition was the determining factor regarding overall seal acceptability.
| |
| M-663-00017 A Attachment B3 Revision WO 1 Page 8 of 8 All the penetration seals examined in Table I visually appeared acceptable with no apparent degradation and thus, are determined acceptable and will perform their intended function with no loss of fire resistance rating. Further engineering basis is provided in the Table I, "Comments/Disposition" column, where applicable.
| |
| Continued Quality Control inspections through implementation of STN FP-452 will ensure ongoing compliance with Regulatory and Fire Protection requirements regarding penetrant service temperature limitations and the potential impact to seal material condition.
| |
| Based on the above discussions and physical examinations, it is reasonable to conclude that penetration seals with temperature issues found visually acceptable (no degradation) will provide the necessary structural and thermal protection from the affects of fire commensurate with requirements of the corresponding M663-00017 typical detail. Therefore, the Table I penetrations are acceptable and will function as designed, concerning service temperature deviations.
| |
| 5.3 Post Fire Safe Shutdown Impact There is no impact to PFSSO systems or components as a result of this evaluation.
| |
| All penetrations have been found visually acceptable with no apparent visual degradation.
| |
| 6.0 Conclusions Table I penetrations with potential service temperature limitation issues have been identified through a comprehensive review of design documentation and were examined in the plant for potential degradation caused by penetrant service temperature exposure.
| |
| These penetration seals visually appeared acceptable with no apparent physical degradation caused by service temperature exposures.
| |
| Based on these examinations, it is concluded that the existing penetration seals are acceptable for their intended service and penetration seal performance is not affected.
| |
| M-663-00017A R ev ision WOI P age 8 3-1 of 8 3-42 Penetration Seal Data Appendix: B3 Penetration
| |
| #: P121S0264 Penetration Type: RB-1 Fire Area (Side 1 ): A-1 Fire Area (Side 2): A-4 Loc./Eiev.: 1988'-0" M-OX Dwg: M-OX1211 1. Barrier Thickness: 19" 10. Annular Gap (smallest)
| |
| : 1" 2. Opening Size: 16" D 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 8"'P 12. Barrier Type: F R W 4. Sea l ant Type: Radflex 13. Opening Sleeved or Concrete:
| |
| Stee l 5. Damming Side1: Unknown 14. Pipe I n sulated: Yes 6. Damming Side 2: Boot Wayne Aregood 7. Damming Cont i nuity (Acc/Rej):
| |
| N/A Prepared By: 8. Boot Condition (Acc/Rej): Accept Jeff Suter 9. Sealant Depth: Assumed Per D eta il Reviewed By: Walkdown Comments: Slab th i ckness determined by dra w ing C-OC 1211 Sketch: FA: A-1 SIDE1 FA: A-4 SIDE2 M-663-00017A Revision WOJ Pa ge 83-2 of B 3-42 Penetration Sea l Data Ap pend ix: 83 Photos: P 1 21S0264 Fire Area A-1 (S ide 1) Fire Area A-1 (Side 1 ) Fire Area A-4 (Side 2) Fire Area A-4 (Side 2)
| |
| M-663-00017A R ev i s ion WOI P age B3-3 of 83-42 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P121S0265 Penetration Type: RB-1 Fire Area (Side 1 ): A-1 Fire Area (Side 2): A-4 Loc./Eiev.: 1988'-0" M-OX Dwg: M-OX1211 1. Barr i er Thickness: 19" 10. Annular Gap (smallest): 1/2" 2. Opening Size: 4" D 11. Gap between pen: N/A 3. Penetra n ts: (1) 1"P 12. Barrie rT ype: F R W 4. Sealant Type: R adflex 13. Open i ng S l eeved o r Concrete: Steel 5. Damm i ng S i de1: Radflex1"recessed 1 4. Pipe I ns ulat ed: Yes 6. Damming Side 2: Boot Wayne Aregood 7. Damming Cont i nuity (Acc/Re j): N/A Prepared B y: 8. Boot Condition (Acc!Re j): Accept Je ff Suter 9. Sea l ant Depth: 31" Reviewed B y: Wa l kdown Comments: Slab th icknes s determined from drawing C-OC1211. I nsulation does not transition through seal zone. Heavy caulk at boot and Rad flex interface. Sketch:
| |
| M-663-000 1 7 A R evis i on W O I P age B 3-4 o f 8 3-4 2 Penetration Seal Data Append i x: 83 Photos: P121S0265 Fire Area A-1 (S i de 1) Fire Area A-1 (S i de 1) F ir e Area A-4 (S i de 2) F i re Area A-4 (S ide 2)
| |
| M-663-000 17 A Revision WO I Pag e B 3-* of B 3-42 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P121S0275 Penetration Type: RB-5A Fire Area (Side 1): A-1 Fire Area (Side 2): A-4 Loc./Eiev.
| |
| : 1988' -0" M-OX Owg: M-OX12 11 1. Barrier Thickness: 19" 24" 0 2. Opening Size: 3. Penetrants
| |
| : (1) 1 0" P 4. Sealant Type: HOSE/HOLE , Ce ram i c Fibe r 5. Damming Side1: Boo t 6. Damming Side 2: B oo t 7. Damming Continuity (Acc/Rej): N I A 8. Boot Condition (Acc/Rej): A c cept 9. Sealant Depth: Assumed Per De t a il Walkdown Comments: Slab th i ckness de t ermined from drawing C-OC1211. Ske t ch: FA: A*1 SlOE: 1 FA: A-4 SIDE! 2 10. Annular Gap (smallest)
| |
| : 1-1/2" 11. Gap between pen: N/A 12. Barrier Type: F R W 13. Opening Sleeved o r Concrete: Steel 14. Pipe Insulated:
| |
| Yes Wayne Aregood Prepared By: Jeff Suter Reviewed By: P121S0275 M-663-000 17A R vision WOl P age 8 3-6 of 8 3-42 Penetration Seal Data Append ix: 83 Photos: P121S0275 F i re A r ea A-1 (S id e 1) F i re Area A-1 (Sid e 1) Fire A re a A-4 (S ide 2) F i re Area A-4 (Si d e 2)
| |
| M-663-00017A , R ev ision WOI P a"'e 83-7 of 8 3-42 Penetration Seal Data Appendix: B3 Penetration
| |
| #: P121S0277 Penetration Type: RB-1 Fire Area (Side 1): A-1 Fire Area (Side 2): A-4 Loc./Eiev.:
| |
| 1988' -0" M-OX Dwg: M-OX1211 1. Barrier Thickness: 1 9" 10. Annular Gap (smallest)
| |
| : 6" 2. Opening Size: 30" D 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 14"P 12. Barrier Type: F R W 4. Sealant Type: Radflex 13. Opening Sleeved or Concrete:
| |
| Steel 5. Damming Side1: B oot 14. Pipe Insulated:
| |
| Yes 6. Damming Side 2: Boo t Wayne Aregood 7. Damming Continuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej): Accept Je ff Suter 9. Sealant Depth: Assumed Per De ta i l Reviewed By: Walkdown Comments: Slab th ickness de te rmined from d raw i ng C-OC121 1. I nsulation appears to transition through sea l area. Penetrant appea rs to be concentrically posi ti oned and annulus i s equal all the way around. Sketch:
| |
| M-663-0001 7A , Revision WOI P age B3-8 of B 3-42 Penetration Seal Data Appe n dix: 83 Photos: P121S0277 Fire Area A-1 (Side 1) Fire Area A-1 (S i de 1) y l 2tl
| |
| * F ir e Area A-4 (S i de 2) F i re Area A-4 (Side 2)
| |
| M-6 63-00017A , R e vi s io n WOJ Penetration Seal Data Penetration
| |
| #: Penetrat i on Type: Loc.!Eiev.: 1988'-0" 1. Barrier Th i ckness: 2. Opening Size: 3. Penetrants
| |
| : P122S0327 RB-SA 19" 24"D (1) 10" P Page 83-9 of 83-42 Appendix:
| |
| B3 F ir e Area (Side 1): A-1 Fire Area (S i de 2): A-2 M-OX Dwg: M-OX 1 221 1 0. Annular Gap (smallest): 6" 11. Gap b e twee n pen: N/A 12. Barrie r Type: F R W 4. Sea l a n t Type: HDSE/HDLE , Cera mi c F i ber 1 3. Ope ning S l eeve d o r Concrete: Stee l 5. Damm in g Side1: Boo t 1 4. Pipe Insulat ed: Y es 6. Damming Side 2: Boot Wayne Are go od 7. Damm i ng Co nti nuity (Acc/Rej):
| |
| N I A Prepared By: 8. Boot Condition (Acc/Re j): A cc ept Je ff S u ter 9. Sealant Depth: Assumed Per Detail Reviewed B y: Walkdown Com m ents: S l ab th i ck n ess determ i ned from draw i ng C-OC 1211. Insulat i on appears to t r ansit i on t hr o u gh seal material. Sketch:
| |
| M-663-000 17A Revis i on WOl P ag 8 3-10 of B 3-4 2 Penetration Seal Data Appendix: 83 Photos: P122S0327 F ire Area A-1 (S i de 1) Fi re A r ea A-1 (Sid e 1) F i re Area A-2 (S id e 2) F ir e Area A-2 (S ide 2)
| |
| M-663-00017A , R evi sion WO l Page B3-l 1 of 83-42 Penetration Seal Data Appendix: B3 Penetration
| |
| #: P122S0339 Pene t ration Type: RB-5A Fi r e Area (S i de 1): A-1 Fire Area (Side 2): A-2 Loc./Eiev.: 1988'-0" M-OX Dwg: M-OX1221 1. Barrier Thickness: 19" 10. Annu la r Gap (sma ll est): 5" 2. Opening S i ze: 30" D 11. Gap be t ween pen: N/A 3. Penetrants
| |
| : (1) 14" P 12. Barr i er Type: F R W 4. Se a lant Type: HDSE/HDLE. Ce ramic F ib er 13. Opening Sleeved o r Concrete: Steel 5. Dam mi ng Side1: Boot 14. Pipe In s ul a t ed: Yes 6. D a mming Side 2: Boot Wayne Aregood 7. Damm i ng Con t inuity (Acc/Rej): N I A Prepared By: 8. Boot Condit i on (Acc/Rej): Accept Jeff Suter 9. Sealant Depth: Assumed Per Detail Reviewed B y: Wa l kdown Com m ents: S lab thickness determined from draw i ng C-OC 1 211. Ske t c h:
| |
| M -663-0001 7 A, R evisi o n WO 1 Page 83-12 of B3-42 Penetration Seal Data Appe n dix: 83 Photos: P12250339 F i re Area A-1 (S id e 1) F ir e A rea A-1 (Side 1 ) Fire Area A-2 (Side 2) Fire Area A-2 (S i de 2)
| |
| M-663-00017A , R ev ision WOl Page 83-13 of 83-42 Penetration Seal Data Appendix: B3 Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2000'-0" 1. Barr i er Thickness: 2. Opening Size: 3. Pene t rants: P131S0526 R B-5A 20'' 1 8"0 (1) 10" P Fire Area (Side 1): A-9 Fire Area (Side 2): A-1 M-OX Dwg: M-1X1 3 11 10. Annul a r Gap (sma ll est): 1" 11. Gap between pe n: N/ A 12. Barr i e r Type: F 4. Sealant T ype: HOSE/HOLE , Ce rami c Fiber 1 3. Openi n g Sleeved o r Concrete: 5. Damm i ng S i de1: Boo t 14. Pipe In su l ated: Yes 6. Damming S i de 2: Boot Wayne Aregood 7. Damming Cont i nuity (Acc/Rej): N/A Prepared By: 8. Boot Co n d i t i o n (Acc/Rej): Accept Jeff S u ter 9. Seala n t Depth: Assumed Per Detail Reviewed B y: Walkdown Comments: R Steel Slab th i ckness based on C-1 C 1311. Ins ulati on appears to go through the sealan t from the bottom side. Howeve r , the top side i nsulation terminates just above the boot. T herefor e , the insulat i on w i ll be assume d not to go through the seal. Sketch: FA:A-9 Sldet P131SOS26 . , -I> () , . . . C>.* ., b
| |
| * F
| |
| * A-1 s do2 M-663-00017A, Revision WOl Pag e B3-l4 of B3-42 Penetration Seal Data Ap p e ndix: 83 Photos: P131S0526 Fire Area A-9 (S id e 1) Fire Area A-9 (Side 1) Fire Area A-1 (S ide 2) Fire Area A-1 (Side 2)
| |
| M-663-00017A , R e vi si on WO I Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2000'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: P131S0528 RM-1A 20" 8" 0 {1)2"P HOSE/HOLE Page 8 3-15 of 83-42 Appendix: B3 F ir e Area (Side 1): A-9 Fire Area (S i de 2): A-1 M-OX Dwg: M-1 X 1311 10. Annular Gap (smallest): 2" 11. Gap b etween pen: N/A 12. Barrier Type: F R 13. Ope nin g S l eeve d o r Concrete: Steel 5. Damming S i de 1: 1-1/2" recessed from top of sleeve 14. P i pe I n s ul ated: *Ye s 6. Damming Side 2: F lu sh Wayne Aregood 7. Damm i ng Continui t y (Acc/Rej): N I A Prepared By: 8. Boot Condition (Acc/Rej): N I A Jeff Suter 9. Sea l ant Depth: 23-1/2" Rev i ewed B y: Walkdown Comme n ts: Slab th i ckness based on C-1 C1311.
| |
| * Locally i nsulated on top s id e , considered i nsulated. Insulation appears to go through. According to inspection report , in sulation protrudes through sea l. Sketch: FA: A*9 Side 1 P131SOS28
| |
| '0 .,
| |
| * I 1 I * ' .
| |
| * P.
| |
| * FA: A*1 S lde2 M -663-000 17 A R evision WO I Pag e 83-1 6 of 83-42 Penetration Sea l Data Appendix: 83 Photos: P131S0528 Fire Area A-9 (Side 1) Fire Area A-9 (Side 1) F i re Area A-1 (S i de 2) F ir e Area A-1 (Si de 2)
| |
| M-663-000 1 7 A , Re v ision WO I Penetrat i on Seal Data Penetration#:
| |
| Penetration Type: Loc./Eiev.: 2000'-0" 1. Barrier Th i ckness: 2. Open i ng Size: 3. Penetra n ts: P131S0530 RB-5A 20" 24"0 {1) 10"P P ag e 83-17 of B3-42 Appendix: B3 Fire Area (Side 1): A-9 Fire Area (Side 2): A-1 M-OX Dwg: M-1X1311 10. Annular Gap (sma ll est): 6" 11. Gap between pen: N/ A 12. Barr i e r Type: F R 4. Sealant Type: HDSE/H DLE , Ceram i c Fiber 13. Open in g Sleeve d o r Concrete: St eel 5. Damming S i de1: Boot 14. Pipe I nsulated: *Yes 6. Damming S i de 2: Boo t Wayne A regood 7. Damming Continu i ty (Acc/Rej): N/A Prepared By: 8. Boot Cond it io n (Acc/Rej): Accept Je ff Suter 9. Sealant Depth: 23" ** Reviewed By: Walkdown Comments: S l ab thick ness based on C-1 C 1 311.
| |
| * From th e bottom s id e examination i t appears that the in su l atio n transitions through the sea l area. ** Sealant depth determined by in spec tion report. Sketch: FA: A-'9 Slde1 P131S0530
| |
| _,.--, '--S...PI'o'lr I I BooT (riP) FA: A.1 Slde2 M-663-00017A Revision W01 Page B3-J of B3-42 Penetration Seal Data A p pend i x: B3 Photos: P13 1 S0530 F ir e Area A-9 (Side 1) Fire Area A-9 (Side 1 ) F i re Area A-1 (S ide 2) Fire Area A-1 (Side 2)
| |
| M-663-00017A , Revision WOJ P age 83-J 9 of B3-42 Penetration Seal Data Appendix: B3 Penetration
| |
| #: P131S0531 Penetration Type: RB-5A Fire Area (Side 1): A-9 Fire Area (Side 2): A-1 Loc./Eiev.:
| |
| 2000'-0" M-OXDwg: M-1X1311 1. Barrier Thickness: 20" 10. Annular Gap (smallest)
| |
| : 1" estimated
| |
| : 2. Opening Size: 16"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) a**p 12. Barrier Type: F R 4. Sealant Type: HDSE/HD LE , Ceram ic F iber 13. Open i ng Sleeved or Concrete: Stee l 5. Damming Side1: Boot 14. Pipe Insulated:
| |
| * Yes 6. Damming Side 2: Boot Wayne Aregood 7. Damming Continuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Ace/Rei):
| |
| Accept Jeff Suter 9. Sealant Depth: 22-1/2" ** Reviewed By: Walkdown Comments:
| |
| Sla b thickness based on C-1 C 13 1 1.
| |
| * It appears that the i nsulation trans i t i ons t hrough the sea l area. Appears to have an FB-6 on top s ide. Ca n n ot absolutely veri fy due to contaminated area. ** Sea l a nt dep th determined by inspect i on report. Sketch: FA: A*9 S i de 1 P131S05 3 1 b ' .
| |
| * 4} "b 1 * 'D, , . . '" * &) I J> I . . , FA: A*1 Side2 M-663-00017A R ev ision WO l P ag 83-20 of B3-42 Penetration Seal Data Appendix:
| |
| 83 Photos: P131 50531 F i re Area A-9 (S ide 1) Fire Area A-9 (S i de 1) Fir e Ar ea A-1 (S ide 2) Fire Area A-1 (Sid e 2)
| |
| M-663-0001 7A , R ev ision WOI P age 83-21 of 8 3-42 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P13250693 Penetration Type: RB-1 Fire Area (Side 1): A-1 0 Fire Area (Side 2): A-1 Loc./Eiev.: 2000'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants:
| |
| : 4. Sealant Type: 20" 24"0 (1)10" P Rad fl ex M-OX Dwg: M-1X1321 10. Annular Gap (smallest):
| |
| 5" 11. Gap between pen: N/A 12. Barrier Type: F 13. Opening Sleeved or Concrete:
| |
| : 5. Damming Side1: Radflex flush w/top of s l eeve 14. Pipe Insulated:
| |
| Yes 6. Damming Side 2: Boot Wayne Areg oo d 7. Damming Continu i ty (Acc/Rej):
| |
| N/A Prepared By: 8. Boot Condition (Acc/Rej): Accept Jeff Suter 9. Sealant Depth: 27" Reviewed By: Walkdown Comments: R Stee l S lab thickness based on C-1 C1311. Insulat i on appear to transition through the sea l. FB-6 could not be confirmed. Sketch: FA: A-10 FB-<.
| |
| Side 1 (iYP) t> \ '-<Q . . .. ... .. l:> . ., . -. * * * * .!'" ,, ("'!"fi')
| |
| !NS!.IIJ/7/();..J (r r,.) FA: A-1 P132S0693 Side2 M-663-000 1 7 A , Revision WO 1 P age 83-22 of B 3-42 Penetration Seal Data Appendix: B3 Photos: P132S0693 Fire Area A-1 0 (Side 1) Fire Area A-1 0 (Side 1) Fire A r ea A-1 (S i de 2) F i re Are a A-1 (S i de 2)
| |
| M-663-000 17 A , R ev ision WO l Page 8 3-23 of 83-4 2 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P133S0799 Penetration Type: RB-1 Fire Area (Side 1 ): A-25 F i re Area (Side 2): A-1 Loc./Eiev.: 2000'-0" M-OX Dwg: M-OX1331 1. Barrier Thickness:
| |
| 1 2" 10. Annular Gap (smallest):
| |
| 4" 2. Opening Size: 24" D 11. Gap between pen: N/A 3. Penetrants:
| |
| (1) 12" P 12. Barrier Type: F R 4. Sealant Type: Ra d flex 13. Open in g Sleeved o r Concrete: S t eel 5. Damming Side1: Un k nown 14. Pipe Insulated:
| |
| Yes 6. Damming Side 2: Boo t Wa y ne Are good 7. Damming Continuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej): A c cept
| |
| * Je ff Suter 9. Sealant Depth: Assumed Per Deta il Reviewed By: Walkdown Comments: *Boot for bottom s i de only , t op side enclosed. Insulat i on appears to trans i tion through th e sea l ant zone. (WSA) (See Draw i ng M-13EJ02; Res i dual Heat Removal Tra in B [EJ] Line Number 009-EC B-1 2" , 350F Des i g n Temp , 2" t hi ck , C l ass i ficat i on "X" Ca l c iu m Si li cate Type Insulat i on) Sketch: FA: A*25 Si de 1 P 133S07Q9 M -663-000 17 A Revision WO I P age 83-24 of 83-42 Penetration Seal Data Appendix: 83 Photos: P133S0799 F ir e Area A-25 (Side 1) Fire Area A-2 5 (S ide 1 ) Fire Area A-1 (S ide 2) Fire Area A-1 (Side 2)
| |
| M-663-0001 7 A , Revision WOI P age B 3-25 of 83-42 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P13350810 Penetration Type: R B-5A Fire Area (Side 1): A-25 Fire Area (Side 2): A-1 Loc./Eiev.: 2000'-0" M-OX Dwg: M-OX1331 1. Barrier Thickness: 12" 10. Annular Gap (smallest)
| |
| : 5" 2. Opening Size: 24"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 10" P 12. Barrier Type: F 4. Sealant Type: HOSE/HOLE , Ceramic F iber 13. Opening Sleeved or Concrete:
| |
| : 5. Damming Side1: Boot 14. P i pe Ins ul ated: Yes 6. Damming Side 2: Boot Wayne Aregood 7. Damming Continuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej): Accept Jeff Suter 9. Sealant Depth: 13" ** Reviewed By: Walkdown Comments: S lab thickness d e t e rmined by Dra wi ng C-1 C 1311. ** Se alant depth determ i ned by inspection report. Sketch: FA: A*25 Slde1 er-n> i ( ('T'I'P')
| |
| P133S01110
| |
| * b ** .. . [>. * .. . *<J.o. -. . . , <J.: ' r} I * ,' .. /:) ... , * \ J * . ()
| |
| * fA: A-1 Slde2 R Stee l M-663-000 17 A Revision WO 1 Page B -26 ofB3-42 Penetration Seal Data Appendix: B3 Photos: P133S0810 Fire Area A-25 (S ide 1) Fire Area A-25 (Side 1) Fire Area A-1 (Si de 2) F ire Area A-1 (Side 2)
| |
| M-663-000 1 7 A , R ev ision WO I Page 83-27 of B3-42 Penetration Seal Data Appendix: 83 Penetration
| |
| #: P134S0860 Penetration Type: RB-1 Fire Area (Side 1): A-24 Fire Area (Side 2): A-1 Loc./Eiev.: 2000'-0" M-OX Dwg: M-1X134 1 1. Barrier Th i ckness: 12" 10. An n u l a r Gap (smallest): 4" 2. Opening S i ze: 24" D 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 12"P 12. Barrier T y pe: F R 4. Sealant Type: Radflex 13. Open in g Sleeved o r Conc r ete: Steel 5. Damming S i de 1:
| |
| * Unknown 14. P i pe I ns ul ated: Yes 6. Damming S i de 2: Boo t Wayne Ar egood 7. Dammi n g Continu i ty (Acc/Rej): N/A Prepared By: 8. Boot Cond i tion (Acc/Rej): ' Accept Jeff Sute r 9. Sealant Depth: Assumed Pe r Detail Reviewed By: Walkdown Comments: S lab thickness based on drawing C-1 C 131 1.
| |
| * Top side seal is covered with support in su l at i on and sh i eld i ng , obscuring inspection attributes.
| |
| I nsulation appears to trans i t i on through the sea l ant via bottom s i de examinat i on. Sketch: FA: A-24 Slde1 P13CSOaocJ
| |
| / --
| |
| uJS\IlltTI
| |
| _ _! _ _ _ __ /
| |
| 8o<IT , "! l** r I :01 I' Ill lbl I 'I>'
| |
| * t)* .... 0 ...* . * ** o> , .. . 0 : .... *: . -"* ' 6 .._ 4t *** p, ........ c .....
| |
| * br rP * *
| |
| * r .. , * ... 6 , ... (T'IP) FA: A-1 Sld112 M-663-000 17 A , Revision WO 1 P age B 3-2 of B J-4 2 Penetration Seal Data Append ix: 83 Photos: P134S0860 F i re Area A-24 (S i de 1) F i re Area A-24 (S i de 1) F ir e Area A-1 (S i de 2) F i re A r ea A-1 (S id e 2}
| |
| M-663-00017 A, Revision W06 Penetration Seal Data Penetration
| |
| #: P135S0227 Penetration Type: FB-1 Loc./Eiev.:
| |
| 2000'-0" 1. Barrier Thickness:
| |
| 16" 2. Opening Size: 10"0 3. Penetrants:
| |
| (1)1"P 4. Sealant Type: Ceramic Fiber 5. Damming Side1: Boot 6. Damming Side 2: Boot 7. Damming Continuity (Acc/Rej):
| |
| N/A 8. Boot Condition (Acc/Rej):
| |
| Accept ------
| |
| Page B3-29 of B3-42 Appendix:
| |
| B5 Fire Area (Side 1 ): A-15 M-OXDwg: M-1X1151 Fire Area (Side 2): A-33 10. Annular Gap (smallest):
| |
| 1 3/4" 11. Gap between pen: N/A 12. Barrier Type: A F w 13. Opening Sleeved or Concrete:
| |
| Steel 14. Pipe Insulated:
| |
| No Wayne Aregood Prepared By: Jeff Suter 9. Sealant Depth: Assumed Per Detail Reviewed By: Walkdown Comments:
| |
| Underside of slab has Q-Decking, effective barrier thickness is measured from corrugated valley. Sketch:
| |
| M-663-00017A , Revision W06 Page 83-30 of 83-42
| |
| * Penetration Seal Data Appendix:
| |
| 85 Photos: P135S0227 Fire Area A-15 (Side 1) Fire Area A-15 (Side 1)
| |
| * Fire Area A-33 (Side 2) Fire Area A-33 (Side 2)
| |
| * M -663-00017 A , R evis ion WO I Pa ge 83-3 1 of 83-42 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P14550952 Penetration Type: FB-1 Fire Area (Side 1): A-2 3 Fire Area (Side 2): A-15 Loc./Eiev.: 2026'-0" M-OX Dwg: M-1X1352 1. Barrier Thickness: 24" 10. Annular Gap (smallest)
| |
| :
| |
| * 1-11/16" 2. Opening Size: 14" D 11. Gapbetweenpen: N/A 3. Penetrants
| |
| : (1) 4"P 12. Barrier Type: A F w 4. Sealant Type: Ceramic Fiber 13. Opening Sleeved or Concrete: Steel 5. Damming S i de1: B oot 14. Pipe Insulated: Y es 6. Damming Side 2: Bo ot Je ff Suter 7. Damming Continuity (Acc/Rej):
| |
| N/A Prepared By: 8. Boot Condition (Acc/Rej): A ccept Wayne A regood 9. Sealant Depth: Assumed per detai l Reviewed By: Walkdown Comments: Slab thickne ss based on C-1 C1352. Top s i de o f penetration is not fully accessible for i nspect i on due to a box enclosure above penetrat i on.
| |
| * Or i g i na l i nspect i on rec o rds in dicate 1-11/1 6" annular gap and the i nstallation of th e Lap Sea l pe r FCR 1-BBI-305 (wsa). Sketch: FA: A-23 Side 1 P145S0952 FA: A*t5 Side 2 M-663-00017A, Revision WOJ Pa ge B3-32 of 83-42 Penetration Seal Data Appendix: 83 Photos: P145S0952 Fire Area A-23 (S id e 1) Fire Area A-23 (S ide 1) F i re Area A-15 (Side 2) Fire Area A-15 (S i de 2)
| |
| M -663-0001 7 A , R e vision WO l P age 3-.,3 of 83-42 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P145S0954 Penetration Type: FB-1 Fire Area (Side 1 ): A-23 Fire Area (Side 2): A-15 Loc./Eiev.:
| |
| 2026'-0" M-OX Dwg: M-1X1352 1. Barrier Thickness: 24" 10. Annular Gap (smallest): 3/8" 2. Opening Size: 14"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1)4"P 12. Barrier Type: A F w 4. Sealant Type: Ceramic F i ber 13. Opening S l eeved or Concrete:
| |
| Steel 5. Damming Side1: B oo t 14. P i pe Insulated:
| |
| Yes 6. Damming Side 2: Boo t Jeff Suter 7. Damming Continuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej):
| |
| Accept Wayne Aregood 9. Sealant Depth: Assumed per deta il Rev i ewed By: Walkdown Comments: Sl ab thickness bas e d on C-1 C 1352. I t appears that a n FB-6 detail was utilized on the tops i de of penetrati on for f looding protect i on o f i nsulation p e netrat in g seal. O rig i na l i nspection records in d i cate the i nstallat i on of t he Lap Seal per F CR 1-BB I-305 (w sa). Sketch: FA; A-23 S i de 1 P1(580954
| |
| : c. r FA: A*1S Side2 M-663-00 0 17 A , Revision WO I P age 83-34 of B3-42 Penetration Seal Data Appendix: 83 Photos: P145S0954 F ire Area A-23 (S id e 1) Fire Area A-23 (Side 1) Fire Area A-15 (Side 2) F ire Area A-15 (Si de 2)
| |
| M -663-000 17 A R evis ion WO 1 Penet r ation Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.:
| |
| 2038'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: 5. Damming Side1: P145W2468 FB-1 36" 14"0 (1) 4" P Ce r am ic F i ber Boot 6. Damming Side 2: Boo t 7. Damming Continuity (Acc/Rej): N/A 8. Boot Condition (Acc/Rej):
| |
| A c cept B3-35 of B3-42 Appendix:
| |
| B3 Fire Area (Side 1): A-23 Fire Area (Side 2): T-2 M-OX Dwg: M-OX1933 10. Annular Gap (smallest)
| |
| : 3/4" 11. Gap between pen: N/A 12. Barrier Type: F 13. Opening Sleeved or Concrete: Stee l 14. Pipe Insulated:
| |
| Y es J e ff Sute r Prepared By: Wayne Are good 9. Sealant Depth: Assumed per deta il Reviewed By: Walkdown Comments: Bar r ier th i ckness based o n draw i ng M-OX 1933. Pipe i s insu l ated through sea l. Sketch: FA: A*23 Slde1 P14SW2468 FA: T-2 Slde2 M-663-000 17A, R evision WOl P age 8" -36 of B3-42 Penetration Seal Data Appendix:
| |
| B3 Photos: P145W2468 F ire Area A-23 (S i de 1) Fire Area A-23 (Side 1) Fire Area T-2 (S ide 2) F ir e Area T-2 (S ide 2)
| |
| M-663-00017A Revision WOl Page 8 3-37 of 83-42 Penetration Seal Data Append ix: B3 Penetration
| |
| #: P145W2469 Penetrat ion Type: F B-1 Fire Area (Side 1): A-23 Fire Area (Side 2): T-2 Loc./Eiev.: 2028'-0" M-OX Dwg: M-OX 1 933 1. Barrier Thickness:
| |
| 36" 10. Annular Gap (smallest):
| |
| 3/4" 2. Opening Size: 1 4"0 11. Gap between pen: N/A 3. Penetrants:
| |
| (1) 4"P 12. Barrie r Type: F 4. Sealant Type: Ceramic Fiber 13. Opening Sleeved or Concrete: Steel 5. Damming Side1: Boot 14. Pipe Insulated: Yes 6. Damming Side 2: Boot Jeff Suter 7. Damming Continuity (Acc/Rej):
| |
| N/A Prepared By: 8. Boot Condition (Acc/Rej):
| |
| Accept Wayne Aregood 9. Sealant Depth: Assumed per deta il Reviewed By: Walkdown Comments:
| |
| Barr ier t h ic k n ess based on drawing M-OX1933. P ipe is ins ula t ed through seal. Sketch: F A: A-23 Skit I J, t 1 )
| |
| I ( FA" T-2 Side 2 M-663-00017A , Revision WOl Page 8 3-3 of 83-42 Penetration Seal Data Appendix: 83 Photos: P145W2469 F ire A r e a A-23 (S id e 1) F i re Area A-23 (S i de 1) F i re Area T-2 (S ide 2) Fire Area T-2 (S i de 2)
| |
| M-663-0001 7A , R e vision WOI Page 8 3-39 of 83-4 2 Penetration Seal Data Appendix: B3 Penetration
| |
| #: P145W2470 Penetration Type: FB-1 Fire Area (Side 1 ): A-23 Fire Area (Side 2): T-2 Loc./Eiev.: 20 28'-0" M-OX Dwg: M-OX19 3 3 1. Barrier Thickness: 36" 10. Annular Gap {smallest)
| |
| : 1-112'' 2. Opening Size: 14" 0 11. Gap between pen: N/a 3. Penetrants:
| |
| (1) 4" P 12. Barrier Type: F 4. Sealant Type: C eram ic F i ber 13. Open i ng Sleeved o r Concrete: Steel 5. Damming Side1: Boo t 14. Pipe Insulated:
| |
| Yes 6. Damming Side 2: Boot Jeff Suter 7. Damming Continuity (Acc/Rej): N I A Prepared By: 8. Boot Condition
| |
| {Acc/Rej): Accep t Wayne Aregood 9. Sealant Depth: Assumed pe r detail Reviewed By: Walkdown Comments: B arrier thicknes s based o n drawing M-OX1933. Pipe i s insu l ated through sea l. Sketch: FA: A*23 P1o45W24 70 '1 ) ) \ FA: T-2 S l de2 M-663-000 17 A , Revision WOl P age B3-4 0 of B 3-42 Penetration Seal Data Appendix: 83 Photos: P145W2470 F ir e Area A-23 (S ide 1) Fire Area A-23 (S id e 1) Fire Area T-2 (S ide 2) Fire Area T-2 (S i de 2)
| |
| M-663-000 17 A , Revi s ion WO l P age 83-41 o f 83-42 Penetration Seal Data Appendix:
| |
| B3 Penetration
| |
| #: P145W2471 Penetration Type: FB-1 F ir e Area (Side 1 ): A-23 F i re Area (Side 2): T-2 Loc./Eiev.: 2028'-0" M-OX Dwg: M-O X 1 933 1. Barrier Thickness: 3 6" 10. Annula r Gap (smallest)
| |
| : 1" 2. Opening Size: 14" 0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 4" P 12. Barrier Type: F 4. Sealant Type: Ce r a m ic F i ber 13. Open i ng S l eeved or Concrete:
| |
| St ee l 5. Damming S i de1: Bo ot 14. Pipe Insulated:
| |
| Yes 6. Damming Side 2: Bo ot Je ff Suter 7. Damming Continuity (Acc/Rej):
| |
| N/A Prepared By: 8. Boot Condition (Acc/Rej): A c c ep t Way ne A r e go od 9. Sealant Depth: Assumed per de t a il Reviewed By: Walkdown Comments: Ba r r i e r thi ck n ess b ased on d raw in g M-OX 1 933. P ipe i s in su l ated th roug h sea l. Sketch: FA.: A-23 Slde1 P145W2471 ) FA: T*2 Sid e 2 M-663-000 1 7 A , Revision WO I P ag 83-42 of 83-42 Penetration Seal Data Appe n d i x: 83 Photos: P145W2471 F ire Area A-23 (S id e 1) Fi r e Area A-23 (S ide 1) Fi re Area T-2 (S ide 2) Fire Area T-2 (S id e 2)
| |
| Rev. No. W01 _i\.._
| |
| CREEK !,r ./NUCLEAR OPERATING CORPORATION M-663-00017 A Attachment 84 Fire Protection Evaluation For Penetrations That Exceed Movement Limitations Prepared By Date Reviewed By ttkf-Wayne S Aregood Jeff Suter 08/19/05 Page 1 Date 08/19/05 M-663-00017A Attachment B4 Revision WO 1 Table of Contents Page 2 of 10 Revision Log ...................................................................................................................................
| |
| 3 1.0 Purpose ...............................................................................................................................
| |
| 4 2.0 Scope ..................................................................................................................................
| |
| 4 3.0 References
| |
| ..........................................................................................................................
| |
| 4 4.0 Assumptions
| |
| ........................................................................................................................
| |
| 5 5.0 Evaluation
| |
| ...........................................................................................................................
| |
| 5 6.0 Conclusions
| |
| .......................................................................................................................
| |
| 10 Appendix B4, Penetration Seal Data ....................................................
| |
| (22 Total Pages)
| |
| M-663-00017 A Attachment 84 Revision WO 1 Revision Reason for Revision W01 Original Issue Page 3 of 10 Revision Log M-663-000 17 A Attachment B4 Revision WO 1 1.0 Purpose Page 4 of 10 1.1 The purpose of this document is to evaluate existing penetration seals that are not directly bounded to the typical detail limitations established in M-663-00017.
| |
| This evaluation was conducted in effort to satisfy regulatory expectation regarding qualification and documentation of fire barrier penetration seals, as discussed in NRC Information Notice 88-04. This evaluation was conducted in accordance with the guidance of NRC Generic Letter 86-10. 2.0 Scope 2.1 The Table I penetrations in relation to the design requirements discussed in Section 5.1. 2.2 Refer to Section 7.0 of M-663-00017A for a cross-reference list of penetrations within Table I that are evaluated for additional seal parameters that do not satisfy the typical detail limitations of M663-00017.
| |
| In these instances, the potential cumulative affects of multiple unbounded attributes were considered for each penetration of concern. 3.0 References 3.1 NRC Generic Letter 86-10, Implementation of Fire Protection Requirements, dated April 24, 1986 3.2 NRC Information Notice 88-04, Inadequate Qualification and Documentation of Fire Barrier Penetration Seals 3.3 10 CFR 50 Appendix R, Fire Protection Program For Nuclear Power Facilities Operating Prior To January 1, 1979 3.4 LER 87-10, Technical Specification Violations-Inoperable Fire Barriers Caused By Personnel Errors 3.5 M-663-00017, Penetration Seal Typical Details, Rev. W20 3.6 STN FP-452, Fire Barrier Penetration Seal Inspection, Rev. 4 3.7 Test Report CTP-1004 (M-663-00084), Irradiation of Flexible Radiation Seals 3.8 Test Report CTP-1065 (M-663-00130), Radiation Exposure, Environmental Aging and Mechanical Cycle Testing, Radflex C Flexible Radiation Seal 3.9 Test Report CTP-1087 (M-663-00133), Radiation Exposure, Environmental Aging and Mechanical Cycle Testing Radflex B Flexible Radiation Seal M-663-00017 A Attachment B4 Revision W01 Page 5 of 10 4.0 Assumptions 4.1 It is assumed that existing penetration seal materials have been installed as required by applicable typical design details and procedures.
| |
| This is an acceptable assumption based on a review of the Quality Control documentation maintained during initial penetration seal installation activities and the intrusive inspections conducted to address LER 87-10, regarding seal material depth. 5.0 Evaluation 5.1 Assessment of Condition to Design Requirements The Table I penetrations contain a penetrant that exceeds the movement limitations of the assigned typical detail from M663-00017.
| |
| The M663-00017 typical detail movement limitations are based on manufacturer identified seal material restrictions and fire tested configurations where the penetrant was subjected to pre-burn mechanical agitation.
| |
| As identified in M663-00017A, penetration scope was determined based on a review of penetration data from EIS in comparison to M663-00017 limitations.
| |
| EIS movement data was then applied to the actual location and orientation of the penetration to ascertain actual penetrant movement directions.
| |
| This was necessary, since application of the X, Y, Z movement directions vary depending on orientation of seal and wall direction.
| |
| TABLE I Penetrations with Penetrant Movements Exceeding Typical Detail Limitation Penetration Communicating Calculated 2 Sealant Number Fire Areas Typical Movement Condition Comments/ (Barrier Detail (inches) Actual Disposition:
| |
| Thickness)
| |
| Side 1 Side2 X y z (Acc./Rej.) (N/S) (Vert) (E/W) P113W0482 A-1 A-5 M-6A -0.077 0.0366 4 0.2828 4 Ace 1 See 5.2.1.3 regarding (12") movement acceptability.
| |
| Seal is acceptable based on visual examination.
| |
| P113W0483 A-1 A-5 M-6A -0.021 0.0266 4 0.0028 Ace 1 See 5.2.1.3 regarding (12") movement acceptability.
| |
| Seal is acceptable based on visual examination.
| |
| P121S0277 A-1 A-4 RB-1 -0.048 0.334 -1.166 4 Ace 1 &3 See 5.2.1.4 for movement (19") limitation acceptability.
| |
| Seal is acceptable based on visual examination and existing annulus. P122S0339 A-1 A-2 RB-5A 0.107 0.361 -1.255 4 Ace 1 &3 See 5.2.1.5 for movement (19") limitation acceptability.
| |
| Seal is acceptable based on the existence of ceramic fiber, boots and sealant depth of 19".
| |
| M-663-00017A Attachment B4 Revision WO 1 Penetration Communicating Number Fire Areas (Barrier Thickness)
| |
| Side 1 Side2 P122W1739 A-1 A-3 (24") P123W0418 A-1 A-5 (12") P145S1010 A-23 A-15 (24") P145W2468 A-23 T-2 (36") P145W2469 A-23 T-2 (36") P145W2470 A-23 T-2 (36") P145W2471 A-23 T-2 (36") Table Notes: Typical Detail X (N/S) RB-8 0.620 4 FB-1 0.388 FB-1 -0.72 FB-1 2.250 4 FB-1 2.250 4 FB-1 2.250 4 FB-1 2.666 4 Page 6 of 10 Calculated 2 Sealant Movement Condition Comments/ (inches) Actual Disposition:
| |
| y z (Acc./Rej.) (Vert) (E/W) -0.315 -0.636 4 Ace 1 See 5.2.1.2 for movement limitation acceptability.
| |
| Seal is acceptable based on visual examination.
| |
| -0.012 1.423 4 Ace See 5.2.1.1 for movement limitation acceptability.
| |
| Seal is acceptable based on direction of movement (axial). -0.238 1.045 4 Ace 1,2&3 See 5.2.1.6 for movement limitation acceptability.
| |
| Seal is acceptable based on visual examination.
| |
| 0.062 0.186 Ace See 5.2.1.1 for movement limitation acceptability.
| |
| Seal is acceptable based on direction of movement (axial). -0.062 0.186 Ace See 5.2.1.1 for movement limitation acceptability.
| |
| Seal is acceptable based on direction of movement (axial). 0.062 0.125 Ace See 5.2.1.1 for movement limitation acceptability.
| |
| Seal is acceptable based on direction of movement (axial). 0.003 -0.044 Ace See 5.2.1.1 for movement limitation acceptability.
| |
| Seal is acceptable based on direction of movement (axial). 1. Additional justification provided in "Comments/Disposition" column. Comment addresses in-plant configuration.
| |
| : 2. Pipe Movements X = (+)NORTH,(-)
| |
| SOUTH y = (+)VERT. UP,(-) VERT. DOWN z = (+)EAST,(-)
| |
| WEST 3. Sealant condition could not be confirmed due to boot installation preventing visual inspections.
| |
| Although, topside boots are not required for RB-1 detail, topside boots have been installed in many instances.
| |
| FB-1detail boot condition was acceptable with no evidence of degradation.
| |
| In some cases topside seal configuration was also enclosed within insulation that prevent sealant inspection, but was accessible on the bottom side to allow visual evaluation of boot. In these cases the boot did not exhibit degradation.
| |
| : 4. Penetrant movement that exceeds limitation of M-663-00017 typical detail.
| |
| M-663-00017 A Attachment 84 Revision W01 Page 7 of 10 5.2 Evaluation of Condition 5.2.1 Penetrant movements are calculated during design phases of the plant and are typically determined based on system operating temperatures and anticipated movement of piping systems. In many instances, depending on the location of the affected penetration seal, the seal may not be subjected to the pre-determined design movements due to heat loss within piping systems, distance from pipe restraints or actual system performance and movements experienced during operation.
| |
| Due to these many variables regarding system design movements, temperatures, seal configurations, and plant environments, the actual sealant conditions are best interpreted (where possible) by in plant visual inspections to determine seal material acceptability.
| |
| The plant has been operating for more than 19 years and degradation caused by excessive system movements would be visually evident for penetrations with sealants exposed, allowing direct visual examination.
| |
| Considering this, acceptability can be determined predominantly through in plant visual inspections.
| |
| The movement issues and penetration seal configurations are specifically discussed below. Table I penetration inspection results are document in Appendix A4-1. 1. FB-1 Penetrations with Large Axial Movement Application of the review methodology identified in Section 5.1 revealed that the movement direction prompting initial concern was in the axial direction for all of the FB-1 penetrations, with the exception of P145S1010.
| |
| M663-00017 typical detail FB-1 limits axial movement to that presented by the slack presented by the boot fold. Field inspection revealed no boot degradation and acceptable boot slack. Therefore, penetrations P123W0418, P145W2468, P145W2469, P145W2470, and P145W2471 are bounded by the typical detail FB-1 limitations regarding penetrant movement, penetration seal P145S1010 is further evaluated below. 2. Penetration P122W1739 The primary sealant for P122W1739 is Radflex, which is extremely durable and flexible.
| |
| One side is booted and the other side is sealed with Silicone Foam to a minimum depth of 1 W', sealing the opening where the system pipe support prevents the installation of a boot. Based on visual examination from the foam side, the seal has no apparent physical degradation caused by movement or environmental exposures.
| |
| Although the Radflex is obscured by the boot and foam installations, it is concluded the Radflex is acceptable because the foam dam side does not exhibit any degradation, and foam has less movement limitations than Radflex. Therefore, it can be concluded that the movements identified are conservative M-663-00017 A Attachment B4 Revision W01 Page 8 of 10 (overstated), and the seal is acceptable based on visual examination and the material limitations discussed.
| |
| : 3. Penetration Movement Slightly Exceeds Typical Detail Limitation Penetrations referenced to this paragraph have movements that are only slightly greater than the typical detail limitations.
| |
| Visual examination determined that damming was unaffected and therefore the underlying sealant can be assumed acceptable.
| |
| The lack of any physical degradation to the damming is basis for the sealant acceptance since the ceramic fiber damming has far less flexibility and elongation characteristics than the sealant material.
| |
| : 4. Penetration P121S0277 Penetration P121S0277 is sealed with Radflex and is booted on both barrier sides. The installed boots prevent physical access to the primary sealant material and visual examination cannot be performed without destructive disassembly.
| |
| The opening has a single penetrant with a lateral movement of 1.166" (worse case). The primary seal material, Radflex, is extremely durable and flexible.
| |
| Test Reports CTP-1087, CTP-1065 and CTP-1004 have successfully tested penetrant movements with simultaneously applied 2" strokes in all three directions (400/200 cycles, as applicable) with no negative consequences.
| |
| Based on this, it is concluded that movements less than 2" with sufficient annulus gaps (twice the specified design movement) are acceptable and will meet intended design function.
| |
| A minimum annulus equal to the movement is required to ensure sufficient Radflex material exists to accommodate system movement and still maintain continuous bond/adhesion to both penetrant and opening surfaces during system movement.
| |
| Because the penetrant is located within the center of the opening, the minimum annulus is approximately 6". This far exceeds the required annulus gap, ensuring the presence of sufficient material to accommodate piping movement and maintain bonding to both substrates.
| |
| Therefore, it is reasonable to concluded that the Radflex is unaffected by the design movements identified.
| |
| Additionally, the Radflex depth of at least 19" provides substantial seal material thickness to protect against a through opening resulting from penetrant movement.
| |
| : 5. Penetration P122S0339 Penetration P122S0339 is a RB-5A booted penetration seal configuration that relies on 3" ceramic fiber contained within the boots (both sides) to provide the fire resistance rating for the penetration seal enclosure.
| |
| The primary function of the boot is to satisfy pressure, water and air tightness requirements, as applicable.
| |
| M-663-000 17 A Attachment B4 Revision W01 Page 9 of 10 Detail RB-5A incorporates a secondary annulus (air gap) to accommodate piping or system movement.
| |
| As such, the booted ceramic fiber is the primary fire resistant material credited for fire rating that is not restricted when the pipe moves, allowing the ceramic fiber to move with the pipe during system cycles. Movement is only restricted by the size of the annulus within the primary sealant (HOLE/HOSE) along with sufficient boot material to accommodate system movement.
| |
| Annulus size was a limitation considered during initial installation and will have no bearing or impact to the seal during operational functions or conditions.
| |
| Visual inspection determined that penetration P122S0339 exhibited no signs of excessive movement or degradation and is therefore, deemed acceptable.
| |
| : 6. Penetration P145S1010 Penetration P145S1010 is a FB-1 detail with boots on both barrier sides. The installed boots prevents physical access to the primary sealant material (ceramic fiber) and internal visual examination cannot be performed without destructive disassembly.
| |
| The opening has two instrument tube penetrants with a lateral movement of 1.045" (worse case), with operating temperatures of 140°F. The internal sealant is 24" (depth) of compressed ceramic fiber, tightly installed throughout the barrier thickness, as required by the installation procedure.
| |
| Both hstrument lines extend out from the seal interface with significant linear length and no rigid support restricting flexural movement.
| |
| This length affords significant flexibility in both instrument lines, thus it is not credible that the postulated movement for these instrument lines could induce destructive compression to the internal sealant material (compressed ceramic fiber). Moreover, these instrument lines have small cross-sectional areas and temperatures that are slightly above ambient. Due to these moderate temperatures identified, the lateral movements originally specified can only be conservative (overstated).
| |
| Both sides of the penetration seal have been examined and found acceptable with no evidence of excessive movements or boot degradation.
| |
| Based on the above discussion, it is concluded that internal sealant compression is not credible.
| |
| Therefore P145S1010 is acceptable regarding penetrant movement.
| |
| Based on the above discussions, it is reasonable to conclude that penetrations with movement issues found visually acceptable (no degradation) will provide the necessary structural and thermal protection from the affects of fire commensurate with the boundary rating. Therefore, penetrations identified in Table I are acceptable and will function as designed, regarding the capability to accommodate penetrant movement while maintaining the required fire resistance rating.
| |
| M-663-00017 A Attachment B4 Revision W01 Page 10 of 10 Continued Quality Control inspections through implementation of STN FP-452 will ensure ongoing compliance with Regulatory and Fire Protection requirements for all Table I penetrations.
| |
| 5.3 Post Fire Safe Shutdown Impact There is no impact to PFSSD systems or components as a result of this evaluation.
| |
| All penetrations have been found visually acceptable with no apparent visual degradation.
| |
| 6.0 Conclusions Table I penetrations with potential penetration movement issues have been identified through a comprehensive review of design documentation and were examined in the plant for potential degradation caused by penetrant movement.
| |
| These penetration seals visually appeared acceptable with no apparent physical degradation caused by penetrant movement.
| |
| Based on these examinations, it is concluded that the existing penetration seals are acceptable for their intended service and penetration seal performance is not affected.
| |
| M-663-00017A R e visio n WOI Page 8 4-J of 84-22 Penetration Seal Data Appendix: B4 Penetration
| |
| #: P113W0482 Penetration Type: M-6A Fire Area (Side 1): A-1 Fire Area (Side 2): A-5 Loc./Eiev.: 1982'-10 M-OX Dwg: M-1X0360 1. Barrier Thickness: 12" Nominal 10. Annular Gap (smallest)
| |
| : 1/2" 2. Opening Size: 4"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1)1-1/2" P 12. Barr i er Type: F 4. Se a la n t Type: Foam 13. Opening Sleeved o r Co n c r ete: Concrete 5. Damm i ng S i de 1: F l ush 14. P i pe I ns u lated: No 6. Damm i ng Side 2: F lu sh Wayne Aregood 7. Damm i ng Continuity (Acc/Rej): Accept Prepared By: 8. Boot Cond i tion (Acc/Rej): N/A Jeff Suter 9. Sealant Depth: 10" Nominal Rev i ewed By: Walkdown Comments: Copper Pipe Sketch:
| |
| M-663-00017A , Revision WOJ Page 84-2 of B4-22 Penetration Seal Data Appendix: B4 Photos: P113W0482 F ire Area A-1 (Side 1) F ire Area A-1 (Side 1) Fire Area A-5 (Side 2) Fire A rea A-5 (S ide 2)
| |
| M-663-00017A , Revision WOI Penetration Seal Data Penetration
| |
| #: P113W0483 Penetration Type: M-6A Loc J Elev.: 1980'-11 1. Barrier Thickness:
| |
| 12" N ominal 2. Opening Size: 4"D 3. Penetrants
| |
| : (1)1-1/2"P 4. Sea l ant Type: F oam 5. Damming Side1: F lush 6. Damm i ng Side 2: F lush 7. Damming Con ti nuity (Acc/Rej): Accept 8. Boot Conditio n (Acc/Rej}: N/A 9. Sealant Depth: 10" Nominal Walkdown Comments: Copper P ipe Sketch: Page 8 4-3 o f 84-22 Appendix: B4 Fire Area (Side 1): A-1 M-OX Dwg: M-1 X03 60 Fire Area (Side 2): A-5 10. Annula r Gap (smallest)
| |
| : 1" 11. Gap between pen: N/A 12. Barr i er Type: F 13. Opening Sleeved or Concrete: 14. P i pe Insulated: No Wayne Aregood Prepared By: Jeff Suter Reviewed By: Concrete M-663-0 0 0 1 7A, Rev i sion W OJ P age 8 4-4 of 84-22 Penetration Seal Data Appendix: B4 Photos: P113W0483 F i r e Area A-1 (S id e 1) Fire Area A-1 (S ide 1 ) Fire Area A-5 (Side 2) Fire Area A-5 (Side 2)
| |
| M-663-00017A , Revision WOI Page B4-5 of B4-22 Penetration Seal Data Appendix:
| |
| B4 Penetration
| |
| #: P121S0277 Penetration Type: RB-1 Fire Area (Side 1): A-1 Fire Area (Side 2): A-4 Loc./Eiev.:
| |
| 1988'-0" M-OX Dwg: M-OX1211 1. Barrier Thickness: 19" 10. Annular Gap (smallest):
| |
| 6" 2. Opening Size: 30" D 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 14"P 12. Barrier Type: F R W 4. Sealant Type: Radfle x 13. Opening Sleeved or Concrete:
| |
| Steel 5. Damming Side1: Boot 14. Pipe Insu l ated: Yes 6. Damming S i de 2: Boot Wayne Aregood 7. Damming Continuity (Ace/Rei):
| |
| N I A Prepared By: 8. Boot Condition (Ace/Rei):
| |
| Accept Jeff Suter 9. Sealant Depth: Assumed Per Deta i l Reviewed By: Walkdown Comments:
| |
| Slab thickness determined from drawing C-O C 1211. Insulation appears to tra nsition th rough seal area. Pe ne tra nt appears to be conc ent rically posit i oned and annu l us is equa l all the way around. Sketch:
| |
| M-663-00017A, R evision WOI P ag e B4-6 o f 84-2 2 Penetration Seal Data Appendix: B4 Photos: P121S0277 Fire Area A-1 (S i de 1) Fire Area A-1 (S i de 1) Fire Area A-4 (S i de 2) Fire Area A-4 (Side 2)
| |
| M-663-00017 A , R e v i sion WOI P age B4-7 of 84-22 Penetration Seal Data Appendix:
| |
| B4 Penetration
| |
| #: P122S0339 Penetration Type: RB-5A F i re Area (Side 1 ): A-1 Fire Area (Side 2): A-2 Loc./Eiev.: 1988'-0" M-OX Dwg: M-OX1221 1. Barrier Thick n ess: 2. Opening S i ze: 3. Penetrants
| |
| : 4. Sealant Type: 5. Damming S i de1: 19" 30"0 (1) 14" P HDSE/HDLE , Ceram i c Fibe r Boot 6. Damming Side 2: Boot 7. Damming Continuity (Acc/Rej): N/A 8. Boot Condition (Acc/Rej): Accept 9. Sealant Depth: Assumed Per Detai l Walkdown Comments: Slab thickness determined from draw i ng C-OC 1 211. Sketch: 10. Annu l ar Gap (smallest): 5" 11. Gap between pen: N/A 12. Barr i er Type: F 13. Open i ng Sleeved o r Concrete: 14. Pipe Insulated: Yes Wayne Aregood Prepared By: Jeff Suter Reviewed By: R W Steel M-663-00017A , R evisi on WOI P age B4-of B4-22 Penetration Seal Data Appendix:
| |
| B4 Photos: P122S0339 Fire Area A-1 (Side 1 ) Fire Area A-1 (S ide 1 ) Fi re Area A-2 (S id e 2) Fire Area A-2 (Side 2)
| |
| M-663-00017A , Re v ision WOI P age 84-9 of B4-22 Penetration Seal Data Appendix:
| |
| B4 Penetration
| |
| #: P122W1739 Penetration Type: RB-8 Fire Area (Side 1): A-1 Fire Area (Side 2): A-3 Loc./Eiev.: 1991'-S" M-OX Dwg: M-OX1913 1. Barrier Thickness:
| |
| 24" 10. Annu l ar Gap (smallest)
| |
| : 2" 2. Opening Size: 10" D 11. Gap between pen: N/A 3. Penetrants:
| |
| (1)2" P 12. Barrier Type: F 4. Sealant Type: Ra dfi ex/Foa m 13. Opening Sleeved or Concrete: Steel 5. Damming Side1: N/A 14. Pipe Insulated:
| |
| No 6. Damming Side 2: Boot Wayne Aregood 7. Damming Continuity (Acc/Rej):
| |
| N/A Prepared By: 8. Boot Condition (Acc/Rej):
| |
| Accept Jeff Suter 9. Sealant Depth: 14-1/2". Reviewed By: Walkdown Comments:
| |
| A l though the movement e xceeds bo unding criter i a , no degradation has been noted in the plant. Des i gn momen t as indicated in E IS exceeds allowable 0.250" but n o degradat i on was obs erved in th e plan t After 18+ years (14 com p lete d refuel cycles) of operatio n , the p ipe moment could not be as re po rted in normal operating condition s.
| |
| * Assumed Per Deta il. Sketch:
| |
| M-663-00017A , Revi ion WOI Page 84-10 of 84-22 Penetration Seal Data Appe nd i x: B4 Photos: P122W 1 739 Fire Area A-1 (S i de 1) Fire Area A-1 (S ide 1) Fire Area A-3 (Side 2) Fire Area A-3 (Side 2)
| |
| M-663-00017A , Revision WOI Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.:
| |
| 1996'-2-1. Barrier Thickness:
| |
| : 2. Opening Size: 3. Penetrants:
| |
| : 4. Sealant Type: 5. Damming Side1: P123W0418 FB-1 12" Nomina l 8"0 (1)2" P Ce r am i c Fiber Boot 6. Damming Side 2: Boot 7. Damming Con t inuity (Acc/Rej):
| |
| N/A 8. Boot Conditio n (Acc/Rej):
| |
| A c cept P age 84-11 of B4-22 Appendix:
| |
| B4 Fire Area (Side 1): A-1 Fire Area (Side 2): A-5 M-OX Dwg: M-1X0360 10. Annular Gap (smallest):
| |
| 1" 11. Gap between pen: N/A 12. Barrier Type: F 13. Opening Sleeved o r Concrete:
| |
| Stee l 14. Pipe Insulated:
| |
| Y es Way n e Ar e good Prepared By: Jeff S u ter 9. Sealant Depth: Assumed Per Deta i l Reviewed By: Walkdown Comments: Side 1: Ceram i c Fiber ve r ified in boot Sketch:
| |
| M-663-0 00 17A , R evi ion WOI P age 84-12 of 84-22 Penetration Seal Data Appendix: B4 Photos: P123W0418 F ir e Area A-1 (S i de 1 ) Fire Area A-1 (S i de 1) F ire Area A-5 (S i de 2) Fire A r ea A-5 (S ide 2)
| |
| M-663-000!7A Re v ision WO J P age B 4-13 o f B4-22 Penetration Seal Data Appendix: B4 Penetration
| |
| #: P145S1010 Penetration Type: F B-1 Fire Area (Side 1): A-2 3 Fire Area (Side 2): A-1 5 Loc./Eiev.: 2026'-0" M-OX Dwg: M-1 X 1352 1. Barrier Thickness: 24" 10. Annular Gap (smallest)
| |
| : 1/2" 2. Opening Size: 3" 0 11. Gap between pen: 1/2" 3. Penetrants
| |
| : (2)3/S"J 12. Barrier Type: A F w 4. Sealant Type: Ceramic Fiber 13. Opening Sleeved or Concrete: Steel 5. Damming Sid e1: Boot 14. Pipe Insulated: No 6. Damming Side 2: Boot Jeff Suter 7. Damming Con t inuity (Acc/Rej): N/A Prepared By: 8. Boot Condition (Acc/Rej): Reject Wayne Aregood 9. Se alant Depth: 24" .. Reviewed By: Walkdown Comments: Sl ab thicknes s based on C-1 C1352. Top side bo ot has a small 3/8" tear. WR i nitiated. ** Sealant depth determined by inspection report. Sketch: FA: A*23 Sid 1 P145S1010 FA: A-15 S l de2 M-663-0 0 017A , Revis i on WOI Pa ge B4-1 4 ofB4-22 Penetration Seal Data Append i x: 84 Photos: P145S1010 Fire Area A-23 (Side 1) F ir e Area A-23 (Side 1 ) Fire Area A-15 (Side 2} Fire Area A-15 (Side 2)
| |
| M-663-00017A , R ev ision WOI P age B4-1 5 of 84-22 Penetration Seal Data Appendix: B4 Penetration
| |
| #: P145W2468 Penetration Type: FB-1 Fire Area (Side 1 ): A-23 Fire Area (Side 2): T-2 Loc./Eiev.: 2038'-0" M-OX Dwg: M-OX 1 933 1. Barr i er Thickness: 36" 10. Annula r Gap (sma ll est): 3/4" 2. Opening Size: 14" D 11. Gap be t ween pen: N/A 3. Penetrants
| |
| : (1) 4"P 12. Barrier Type: F 4. Sea l ant Type: Ceram i c F ib er 13. Open i ng Sleeved or Concrete: Steel 5. Damming Side1: Boot 14. Pipe Insulated: Yes 6. Damming Side 2: Boot Je ff Suter 7. Damming Con t i nuity (Acc/Rej): N I A Prepared By: 8. Boot Condition (Ace/Rei): A cc ept Wayne Are go od 9. Sealant Depth: Assumed per deta il Reviewed By: Walkdown Comments: Barrier thickness based on draw in g M-OX1933. P ipe is in sulated through seal. Sketch: FA:. A*23 FA: T -2 Slde2 M-663-0001 7A , Revision WOJ Pag B4-16 ofB4-22 Penetration Seal Data Appendix: B4 Photos: P145W2468 Fire Area A-23 (S ide 1) Fir e Area A-23 (Side 1) F ir e Area T-2 (S ide 2) Fire Area T-2 (S ide 2)
| |
| M-663-00017A, Revision WOJ Penetration Seal Data Penetration
| |
| #: P145W2469 Penetration Type: Loc./Eiev.
| |
| : 2028'-0" 1. Barr i er Thickness: 2. Opening Size: 3. Penetrants
| |
| : FB-1 36" 14"0 (1) 4" P 4. Sea lant Type: Ceram i c Fiber 5. Damm in g Side1: Boot 6. Damming Side 2: Boot 7. Damming Continu it y (Acc/Rej): N/A 8. Boot Condition (Acc/Rej): Accept Pa ge 84-17 o f 84-22 Appendix:
| |
| B4 Fire Area (Side 1): A-23 Fire Area (S i de 2): T-2 M-OX Dwg: M-OX1933 10. Annular Gap (smallest)
| |
| : 3/4" 11. Gap between pen: N/A 12. Barr ie r Type: F 13. Opening Sleeved o r Concrete: Stee l 14. Pipe Insul ated: Yes Jeff Suter Prepared By: Wayne Aregood 9. Sealant Depth: Assumed per deta i l Reviewed By: Walkdown Comments: Ba rrier th i ckness b ased on draw i ng M-OX1933. P i pe is insulated through sea l. Ske tch: F A: A*23 S lde1 J '1' { l ) P145W2469 -I 1 )
| |
| M-663-00017A Revision WOI Pa ge 84-1 of 84-22 Penetration Seal Data Appendix:
| |
| B4 Photos: P145W2469 Fire Area A-23 (S i de 1) F ir e Area A-23 (S ide 1) F ire Area T-2 (Side 2) Fire Area T-2 (Side 2)
| |
| M -663-00017 A , Revision WO I Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2028'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: 5. Damm ing Side1: P145W2470 FB-1 36" 14"0 (1) 4"P Ceram ic F iber Boot 6. Damm in g Side 2: Boot 7. Damming Continuity (Acc/Rej): N/A 8. Boot Condition (Acc/Rej):
| |
| Accept P age B4-19 o f 84-22 Appendix:
| |
| B4 Fire Area (Side 1): A-23 Fire Area (Side 2): T-2 M-OX Dwg: M-OX 1933 10. Annular Gap (smallest)
| |
| : 1-1/2" 11. Gap between pen: N/a 12. Barrier Type: F 13. Opening Sleeved or Concrete: Stee l 14. Pipe Insulated:
| |
| Ye s Jeff Su ter Prepared By: Wayne Aregood 9. Sealant Depth: Assumed per deta il Reviewed By: Walkdown Comments:
| |
| Bar rier th i ckness based on drawing M-OX1933. P i pe i s in su lated through sea l. Sketch: FA. A-23 Side 1 P145W2,70 . ) \ FA: T-2 Slde2 M-663-000I?A, Revision WOI Page 84-20 of 84-22 Penetration Seal Data Appendix: B4 Photos: P145W2470 Fire Area A-23 (Side 1) Fire Area A-23 (Side 1) Fire Area T-2 (Side 2) Fire Area T-2 (S ide 2)
| |
| M-663-00017A , R ev ision WOI Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2028'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Seal a nt Type: 5. Damming Side1: P145W2471 FB-1 36" 14" D (1) 4" P Ceramic F i ber Boot 6. Damming Side 2: Boo t 7. Damming Continuity (Acc/Rej): N/A 8. Boot Condition (Ace/Rei): A ccept Page B4-2 l of 84-22 Appendix:
| |
| 84 Fire Area (Side 1 ): A-23 Fire Area (Side 2): T-2 M-OX Dwg: M-O X 1933 10. Annular Gap (sma ll est): 1" 11. Gap between pen: N/A 12. Barrier Type: F 13. Open i ng Sleeved or Concrete: Stee l 14. Pipe Insulated: Y es Je ff Suter Prepared By: Wayne Aregood 9. Sealant Depth: Assumed per deta il Reviewed By: Walkdown Comments: Ba r r ie r thickness based on drawing M-OX1933. P ipe is in sulated th roug h sea l. Sketch: FA: A-23 Side 1 P145W2471 FA; T-2 Sida2 M-663-0 0 0 1 7 A Revision W Ol Pa ge 84-22 o f 84-22 Penetration Seal Data Append i x: B4 Photos: P145W2471 Fire Area A-23 (Side 1) F ir e Area A-23 (S ide 1) Fire Area T-2 (Side 2) F i re Area T-2 (S i de 2)
| |
| Page 1 CREEK lr '/NUCLEAR OPERATING CORPORATION M-663-00017 A Attachment 85 Fire Protection Evaluation For Penetrant Size Exceeding Typical Detail M -1 Limitation Rev. No. Prepared By Date Reviewed By Date W01 08/19/05 08/19/05 Jeff Suter Wayne S Aregood M-663-00017 A Attachment 85 Revision WO 1 Table of Contents Page 2 of? Revision Log ...................................................................................................................................
| |
| 3 1.0 Purpose ...............................................................................................................................
| |
| 4 2.0 Scope ..................................................................................................................................
| |
| 4 3.0 References
| |
| ..........................................................................................................................
| |
| 4 4.0 Evaluation
| |
| ...........................................................................................................................
| |
| 5 5.0 Conclusions
| |
| .........................................................................................................................
| |
| 7 Appendix 85, Penetration Seal Data ....................................................
| |
| (48 Total Pages)
| |
| M-663-00017A Attachment 85 Revision W01 Revision Reason for Revision W01 Original Issue Page 3 of? Revision Log M-663-00017 A Attachment BS Revision W01 1.0 Purpose Page 4 of? 1.1 The purpose of this document is to evaluate existing penetration seals that are not directly bounded to the typical detail limitations established in M-663-00017.
| |
| This evaluation was conducted in effort to satisfy regulatory expectation regarding qualification and documentation of fire barrier penetration seals, as discussed in NRC Information Notice 88-04. This evaluation was conducted in accordance with the guidance of NRC Generic Letter 86-10. 2.0 Scope 2.1 The Table I penetrations in relation to the design requirements discussed in Section 5.1. 2.2 Refer to Section 7.0 of M-663-00017 A for a cross-reference list of penetrations within Table I that are evaluated for additional seal parameters that do not satisfy the typical detail limitations of M-663-00017.
| |
| In these instances, the potential cumulative affects of multiple unbounded attributes were considered for each penetration of concern. 3.0 References 3.1 NRC Generic Letter 86-10, Implementation of Fire Protection Requirements, dated April 24, 1986 3.2 NRC Information Notice 88-04, Inadequate Qualification and Documentation of Fire Barrier Penetration Seals 3.3 10 c*FR 50 Appendix R, Fire Protection Program For Nuclear Power Facilities Operating Prior To January 1, 1979 3.4 LER 87-10, Technical Specification Violations -Inoperable Fire Barriers Caused By Personnel Errors 3.5 M-663-00017, Penetration Seal Typical Details, Rev. W20 3.6 Fire Test CTP-1001 (M-663-00082), Fire Qualification Test on Silicone Foam Floor Penetration Seals 3.7 Fire Test CTP-1009 (M-663-00148), 9" Depth 3-6548 Silicone RTV Foam w/Site Specific SNUPPS Cable and Repair 3.8 Fire Test IC01 091035 (M-663-00156), 3 Hour Fire Resistance Evaluation of Ten Different Penetration Seal Designs 3.9 Fire Test 03-5656-001 Slab 5 (M-663-00157), Fire Qualification Test on Silicone Foam Floor Penetration Seals, Slab 5 M-663-000 17 A Attachment 85 Revision WO 1 4.0 Assumptions Page 5 of 7 4.1 It is assumed that existing penetration seal materials have been installed as required by applicable typical design details and procedures.
| |
| This is an acceptable assumption based on a review of the Quality Control documentation maintained during initial penetration seal installation activities and the intrusive inspections conducted to address LER 87-10, regarding seal material depth. 5.0 Evaluation 5.1 Assessment of Condition to Design Requirements The penetration openings identified in Table I contain a pipe penetrant that exceeds the size limitation directly bounded by typical detail M-1 from M663-00017. The M-1 typical detail, which is comprised of a 6" Silicone Foam and ceramic fiber damming, directly qualifies a seal with up to a 4" diameter penetrant as 3-hour fire (F) and temperature (T) rated. TABLE I M-1 Penetrations with Penetrant Size Exceeding Typical Detail Limitations
| |
| -Penetration Communicating Penetration Pipe Silicone Comments/
| |
| Number Fire Areas Orientation Penetrant Foam Disposition Side 1 Side 2 Diameter Depth P113W0420 A-1 A-5 Wall 8" 8-1/4" See 5.2.2 P132S0680 A-8 A-1 Floor/Ceiling 6" 7" See 5.2.1 P132W1440 A-8 CC-1 Wall 6" 7" See 5.2.1 P132W1441 A-8 CC-1 Wall 6" 6-1/2" See 5.2.1 P133W2039 A-8 A-25 Wall 6" 8.5 See 5.2.1 P135W2208 A-13 A-29 Wall 6" 7" See 5.2.1 P135W2449 A-29 A-30 Wall 6" Assumed See 5.2.1 Per Detail P154S1267 A-19 A-16 Floor/Ceiling 6" Assumed See 5.2.1 per detail P321S0081 C-5 C-1 Floor/Ceiling 5" 7" See 5.2.1 P331W0162 C-9 C-1 0 Wall 6" 7-1/2" See 5.2.1 P341W0209 C-35 C-13 Wall 6" 6" Nominal See 5.2.1 P341W0216 C-35 C-14 Wall 6" 6" Nominal See 5.2.1 P341W0227 C-35 C-16 Wall 6" 6 3/8" See 5.2.1 P341W0250 C-35 C-15 Wall 6" 6 1/4" See 5.2.1 Nominal P351S0371 C-21 C-16 Floor/Ceiling 6" 8" See 5.2.1 P611W0083 F-2 F-3 Wall 6" 7" See 5.2.1 M-663-00017 A Attachment 85 Revision WO 1 Page 6 of 7 5.2 Evaluation of Condition 5.2.1 Penetrations with a Maximum 6" Diameter Penetrant The Table I penetrations with up to a 6' diameter pipe penetrant are determined to be 3-hour F rated based on comparison to blackout 6 from fire test report CTP-1001.
| |
| The 12" x 54'' blackout, sealed with a 6" depth of Silicone Foam over 1" ceramic fiber damming, contained multiple penetrants including a 6' spare conduit and a 6" conduit with 1 00% visual cable fill. The blackout successfully prevented the passage of flame and hot gases to the unexposed side for a 3-hour fire exposure duration.
| |
| It also successfully passed the required post burn hose stream test. However, the unexposed seal surface temperatures for the spare 6' conduit exceeded the Wolf Creek 3-hour T rating unexposed side seal surface temperature limitation of 325°F plus ambient necessary to achieve a 3-hour T rating. The maximum seal surface temperature exhibited by the test assembly was 446°F. M-663-00017 identifies that where piping penetrations exist that do not satisfy T rating requirements, a seal assembly with an F rating corresponding to the hourly rating of the associated barrier is acceptable, provided evaluation demonstrates that exposed insitu combustibles and redundant post fire safe shutdown (PFSSD) equipment/circuits on the unexposed barrier side will not be detrimentally affected by the increased penetrant temperatures.
| |
| In effort to evaluate fire area impact, field walk-downs and comprehensive assessment reviews, documented in Appendix 85, were conducted for each penetration of concern. This review was completed in accordance with the criteria and review methodology established in M-663-00017A Section 7.2.3 for non-T rated penetrations.
| |
| The review identified that no exposed insitu combustibles or PFSSD circuits are located within the heat affected zone. Each of the penetrations satisfies the review criteria of M-663-00017 where T rating requirements are not met. Therefore, the penetrations are acceptable, as this evaluation demonstrates reasonable assurance that the penetration seals do not present a negative impact to PFSSD capability.
| |
| 5.2.2 Penetration P113W0420 Penetration P113W0420 is sealed with an 8-1/4" depth of Silicone Foam between 1" ceramic fiber damming. The 8" diameter penetrant size exceeds the 4" penetrant limitation of typical detail M-1. Although the penetration does not contain the 9" Silicone Foam depth required by typical detail M-6A, it is considered 3-hour F and T rated when compared to the fire tested configurations and associated evaluations defining the limitations of detail M-6A.
| |
| M-663-00017 A Attachment 85 Revision W01 Page 7 of? Fire test CTP-1 009 contained a penetration sealed with 9" of Silicone Foam over 1" ceramic fiber damming, resulting in a 10" total seal depth. The penetration was fire tested in a slab orientation.
| |
| This fire test in comparison with the performance of IC01 091035, Penetration 3 and 03-5656-001 Slab 5 Penetration 148 (12" Silicone Foam seals), was also utilized as the basis for allowing up to a 10" diameter pipe penetrant for M-6A Additionally, as established in M663-00017, a floor/ceiling tested assembly presents a more severe fire exposure, thus bounding a wall seal configuration provided seal symmetry is addressed.
| |
| P113W0420 is a wall penetration.
| |
| It is provided ceramic fiber damming on both barrier sides, resulting in a symmetrical seal with a total depth of 10-1/4". Industry testing has repeatedly demonstrated that the fire resistive performance of ceramic fiber is superior to Silicone Foam, predominantly because ceramic fiber does not char (unlike Silicone Foam), when directly subjected to flame exposure.
| |
| Since P113W0420 contains a greater btal seal depth than when M-6A is applied in the worse case floor/ceiling configuration, it reasonable to conclude that the penetration will perform at least as well M-6A Therefore, penetration P113W0420 is considered 3-hour F and T rated. Conservatively, the heat affected zone for this penetration was also reviewed in accordance with the criteria and methodology of established in M-663-00017A Section 7.2.3 for non-T rated penetrations.
| |
| The review identified that no exposed insitu combustibles or PFSSD circuits are located within the heat affected zone for penetration P113W0420.
| |
| 5.3 Post Fire Safe Shutdown Impact There is no impact to PFSSD systems or components as a result of this evaluation.
| |
| Penetration P113W0420 provides en equivalent 3-hour F and T rated seal. The remaining Table I penetrations are 3-hour F rated. The comprehensive walkdown review for each of these penetrations revealed that no exposed insitu combustibles or PFSSD circuits are negatively affected by the non T rated penetrations.
| |
| 6.0 Conclusions Penetration P113W0420 was determined to provide an equivalent 3-hour F and T rated seal. Based on the above discussions, it is reasonable to conclude that the remaining Table I penetration seals are acceptable as 3-hour F rated and will perform their intended function, regardless of not achieving a T rating. The penetration seals satisfy regulatory requirements and commitments as well as WCNOC Fire Protection Program requirements, to prevent spread of fire from one fire area to another. It has also been determined through this evaluation that the lack of a T rating will not affect the plant's ability to achieve and maintain PFSSD.
| |
| M-663-00017A , R ev ision WOJ Penetration Seal Data Penetration#:
| |
| Penetration Type: Loc./Eiev.:
| |
| 1984'-8" 1. Barrier Thickness:
| |
| : 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: 5. Damming Side1: 6. Damming Side 2: P113W0420 M-1 12" Nominal 12"0 (1) S"P Foam Flush w/sleeve 2-3/4" Recess 7. Damming Cont i nuity (Acc/Rej):
| |
| Accept 8. Boot Condition (Acc/Rej):
| |
| N/A 9. Sealant Depth: 8-1/4" Walkdown Comments: Sketch: Appendix:
| |
| B5 Fire Area (Side 1): A-1 M-OX Dwg: M-1X0360 Fire Area (Side 2): A-5 10. Annular Gap (smallest):
| |
| 1-3/8" 11. Gap between pen: N/A 12. Barrier Type: F 13. Opening Sleeved or Concrete: 14. Pipe Insu lat ed: No Wayne Aregood Prepared By: Jeff Suter Reviewed By: Steel M-663-00 017 A , R ev i sion W O J P age 8 5-2 of B--4 Penetration Seal Data Ap p end i x: 85 Photos: P113W0420 F i re Area A-1 (Side 1) F i re Area A-1 (S i de 1 ) F i re A r ea A-5 (S i de 2) F ir e Area A-5 (Side 2}
| |
| M-6 6 3-00017A R ev ision WOJ P age 85-3 of 85-4 Penetration Seal Data Appendix: 65 Heat Affected Zone Review: P113W0420 Fire Area (Side 1) A-1 Review Distances (ReferenceM-663-00017A.
| |
| Ftgure 7.2.:>-1) No i ssues within Heat Affected Zone 8" Pipe L1 & L2 Temp. R1 Radius R2 Radius D i st. (ft) (O F) .(in) (i n) 0.5 1677 4.4 5.8 1 1463 3.4 4.8 Fire Area (Side 2) A-5 1.5 1277 2.6 3.9 No is sues w i thin Heat Affected Z one 2 1116 1.9 3.2 2.5 976 1.2 2.6 3 855 0.7 2 3.5 750 0.2 1.6 4 659 Contact 1.2 4.5 58 1 0.8 5 512 0.5 Side 1 Photo Side 2 P h oto 5.5 453 0.2 6 402 0 6.5 358 Conta ct No photo required.
| |
| No photo required.
| |
| Sketc h No sketch required.
| |
| M-663-000I?A , R evis ion WOJ Page B5-4 of 8 5-48 Penetration Seal Data Appendix: BS Penetration
| |
| #: P132S0680 Penetration Type: M-1 F i re Area (S i de 1 ): A-8 Fire Area (S i de 2): A-1 Loc./Eiev.: 2000'-0" M-OX Dwg: M-1X1321 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Sea l a n t Type: 5. Damm in g Side1: 6. Damm i ng Side 2: 12" 10"D (1) 6''P Foam Foam flush w/top of sleeve Recessed 4" from bar r i er plane 7. Damm i ng Continu i ty (Acc/Rej): Accept 8. Boot Condition (Acc/Rej): N/A 9. Sealant Depth: 7" Walkdown Comments:
| |
| S lab thickness de t erm i ned by Drawing C-1C1311 (wsa) Sketc h: FA: A-1 S i de 1 P132S0680
| |
| : 10. Annular Gap (sma ll est): 1" 11. Gap between pe n: N/A 12. Barr i er Type: F 13. Opening Sleeved o r Conc r ete: 14. P i pe In s ul a t ed: No Jeff Suter Prepared By: Wayne Aregood Reviewed By: FA: A-1 Slde2 Steel M-663-00017A , R e vision WOI P age B S-5 of B S-4 8 Penetration Seal Data Appe nd ix: BS Photos: P132S0680 Fire Area A-8 (S i de 1) Fi re Area A-8 (S i de 1) F ir e Area A-1 (S id e 2) Fi re Area A-1 (S ide 2)
| |
| M-663-00017A , Revision WOJ P age B -6 of B S-4 8 Penetration Seal Data Appendix: 85 Heat Affected Zone Review: P132S0680 Fire Area (Side 1) A-8 Review Distances (Reference M-663-{)0017 A. Fogute 7 2.3-1 ) No issues within Heat Affected Zone 6" Pipe L1 & L2 Temp. R1 Radius R2 Radius Dist. (ft) (o F) (in) (in) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 Fire Area (Side 2) A-1 1.5 1236 2.4 3.8 No i ssues within Heat A ff ected Zone 2 1069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 Contad 1.3 4 608 0.9 4.5 53 1 0.6 5 464 0.3 Side 1 Photo Side 2 Photo 5.5 408 0 6 3 5 9 C ontact No photo requ i red. No photo required.
| |
| Sketch No sketch required.
| |
| M-663-00017A
| |
| , R ev is i o n WOJ Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2014'-2" 1. Barrier Thickness: 2. Opening Size: 3. Penet r ants: 4. Sealant T ype: 5. Dam min g S i de1: 6. Dammi n g Side 2: P132W1440 M-1 24" 14"0 (1) 6'"P F o a m F l u sh 15" re cess e d 7. Dam m ing Continuity (Acc/Rej): Acc e pt 8. Boot Condition (Acc/Rej): N/A 9. Sea l ant Depth: 7" Walkdown Comments:
| |
| P a ge BS-7 o f 85-4 8 Appendix: BS F ir e Area (S i de 1 ): A-8 F i re Area (S i de 2): CC-1 M-OX Dwg: M-1 X 1 904 10. Ann ul a r Gap (sma lle st): 1/2" 1 1. Gap be t ween pen: N/A 12. Barr i er T ype: A F 1 3. Open i ng S l eeved o r Concrete:
| |
| Steel 1 4. Pipe I ns ul ated: Y es Wayne Aregood Prepared B y: Je ff S ut e r Reviewed B y: Insu l a tion d oes n o t go t h rou gh the p rima r y se al an t or d a mm in g. Sketch: F A: A-8 S i de f P132W 1 44 0 F A: CC-I S i de2 M-663-000 1 7 A , R evision WO I Pa ge 85-Penetration Seal Data Append i x: 85 Photos: P132W1440 Fi re Area A-8 (S id e 1) Fire Area A-8 (Side 1) F ire Area CC-1 (S id e 2) Fire Area CC-1 (S i de 2)
| |
| M-663-00017 A , R e v isi on WOl P a ge 8 5-9 of B--4 8 Penetration Seal Data Appendix:
| |
| 85 Heat Affected Zone Review: P132W1440 Fire Area (Side 1) A-8 Rev i ew Dista n ces (ReferenceM-063-00017A , F 1gure 72.3-1) No i ssues wi t hin Heat A f fected Zone 6" Pipe L1 & L2 Temp. R1 Radius R2 Radius D i st. (ft) (*F) (in) (i n) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 Fire Area (Side 2) C C-1 1.5 1236 2.4 3.8 2 No i ssues w i th in H e a t A ff ec t ed Zone 1 069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 C ontact 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 S i de 1 Photo S i de 2 Photo 5.5 408 0 6 359 C ontact No photo requ i red. No photo required.
| |
| Sketch No sket ch r equ ir ed.
| |
| M -66 3-000 I 7 A , R ev i s ion WO 1 P age B--1 0 of BS-48 Penetration Seal Data Appendix: BS Penetration#:
| |
| P132W1441 Penetration Type: M-1 Fire Area (Side 1): A-8 Fire Area (Side 2): CC-1 Loc./Eiev.: 2014'-2" M-OX Dwg: M-1X1904 1. Barrier Th i ckness: 24" 10. Annular Gap (smallest): 2" 2. Opening Size: 14"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 6" P 12. Barrier Type: A F 4. Sealant Type: Foam 13. Open i ng S l eeved o r Concrete: Steel 5. Damm in g Side1: F lu sh 14. P i pe In s ul ated: Yes 6. Damming S i de 2: 1 5-1/2" Wayne Aregood 7. Damm i ng Continu i ty {Acc/Rej): Accept Prepared By: 8. Boot Condition (Acc/Rej): N/A Jeff Suter 9. Sealant Dept h: 6-1/2" Reviewed By: Walkdown Comments:
| |
| Insulation does not go thr ough the pr i mary sea l an t or damming. Sketch: FA: A*8 Side 1 P132W1441
| |
| * * ,, * .* .<J.* ' P .* . . ...... b.. . . FA: CC*I Side 2 M -6 63-00017 A R evisi on WO l Penetration Seal Data Appendix: B5 Photos: P132W1441 Fire Area A-8 (S id e 1) Fire A rea A-8 (Side 1 ) Fire Area CC-1 (S ide 2) Fire Area CC-1 (S i de 2}
| |
| M-663-000J7A R e vision WOJ P age 8 5-1 2 of B--48 Penetration Seal Data Appendix: 85 Heat Affected Zone Review: P132W1441 Fire Area (Side 1) A-8 Review Distances (Rererenca Mo663-00017A.
| |
| F 1gure 7.2.3-1 ) No i ssue s wi t hin Hea t A ff e c ted Z on e 6" Pipe L1 & l2 Temp. R1 Radius R2 Radius Dist. (ft) (o F) (in) (in) 0.5 1659 4.3 5.7 1 14 3 1 3.3 4.6 Fire Area (Side 2) CC-1 1.5 12 3 6 2.4 3.8 No i ssues w it h in Heat A ff ecte d Zon e 2 1069 1.7 3 2.5 925 1 2.4 3 80 3 0.5 1.8 3.5 698 C ontact 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 Side 1 Photo Side 2 Photo 5.5 408 0 6 359 C on t act No photo requ i red. No photo required.
| |
| Sketch No sketch required.
| |
| M-6 63-00017A , R evi sion WO J Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 20 1 7'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: P133W2039 M-1 36" 12"0 (1) 6"P Foam P age 85-13 of 85-4 Appendix:
| |
| 85 Fire Area (Side 1 ): A-8 F i re Area (S i de 2): A-25 M-OX Dwg: M-1 X 1 921 10. Annular Gap (sma ll est): 3/4" 11. Gap between pen: N/A 12. Barrier Type: F w 1 3. Opening S l eeved or Concrete:
| |
| Steel 5. Damm i ng S i de1: Flush w it h barr ier p l ane 1 4. Pipe I n s ul ated: No 6. Damming Side 2: Recessed 25-1/2" 7. Damming Cont i nuity (Ace/Rei): Accept 8. Boot Condition (Acc/Rej): N/A 9. Sealant Depth: 8.5 Walkdown Comments: Barr i er thickness determined by Draw in g C-1 C 1 33 1 (w sa) Sketch: FA: A-8 S i de 1 P133W2039
| |
| ). a. Jeff Suter Prepared By: Wayne A regood Reviewed B y: FA: A*25 S i de 2 M-663-0 00 I?A , R evisi o n W O I P age 8 5-14 of 8 5-48 Penetration Seal Data Ap p e n d i x: 85 Photos: P133W2039 Fire Area A-8 (S i de 1 ) Fire Area A-8 (S i d e 1) Fire A r ea A-25 (Side 2) Fire Area A-25 (S i de 2)
| |
| M-663-0001 7 A , R evision WOI Page BS-1 -of 85-4 Penetration Seal Data Appendix:
| |
| 85 Heat Affected Zone Review: P133W2039 Fire Area (S id e 1) A-8 Review Distances (Reference Fogure 7.2.3-1) No issues with Heat A ff ected Zo ne 6" Pipe L1 & L2 Temp. R1 Radius R2 Radius D i st. (ft) (O F) (in) (in) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 Fire Area (Side 2) A-25 1.5 1236 2.4 3.8 No issues w i t hin Heat Affected Zone 2 1069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 Con t a ct 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 S i de 1 Photo S ide 2 Photo 5.5 408 0 6 359 Contact No photo required.
| |
| No photo required.
| |
| Sketch No sketch required.
| |
| M-663-000I?A , R ev ision WOJ Page BS-16 of 85-4 Penetration Seal Data Appendix:
| |
| B5 Penetration
| |
| #: P135W2208 Penetration Type: M-1 Fire Area (Side 1): A-13 Fire Area (Side 2): A-29 Loc./Eiev.: 2009 '-1" M-OX Dwg: M-1X1924 1. Barrier Thickness:
| |
| 12" 10. Annular Gap (smallest):
| |
| 3/4" 2. Opening Size: 10"D 11. Gap between pen: N/A 3. Penetrants:
| |
| (1) 6" P 12. Barrier Type: F 4. Sealant Type: Foam 13. Open i ng Sleeved o r Concrete: 5. Damm in g Side1: 3"recessed
| |
| : 14. Pipe Insulated:
| |
| No 6. Damming Side 2: F lu sh Wayne Aregood 7. Damming Continuity (Acc/Rej):
| |
| Accept Prepared By: 8. Boot Condition (Ace/Rei):
| |
| N/A Jeff Suter 9. Sealant Depth: 7" Reviewed By: Walkdown Comments:
| |
| Barrier thickness determined by Drawing M-1 X1151 Sketch: FA: A*,3 SICS. 1 . " -* .* . c. '!>''---li-t. ,. * * . . 0. 'b . . . FoA d"l -..,------1----.J (""'"'*) ' . . _L._;..* .....:.*--J
| |
| '\.1, __ _._ FA: Slde2 w Steel M -663-0001 7 A, R evis i on WO 1 Penetration Seal Data Appendix: B5 Photos: P135W2208 Fire Area A-13 (S i de 1 ) F ire A r ea A-1 3 (Side 1) Fi re Area A-29 (Side 2) F ire Area A-2 9 (S i de 2)
| |
| M-663-00017A , R ev is i on WOI Penetration Seal Data Heat Affected Zone Review: P135W2208 F i re Area (Side 1) A-13 1. 4" Pipe with Armaflex insula t ion , Not W/in Heat Affected Zone Fire Area (Side 2) A-29 2. 1-1/2" Condu it within Heat Affected Zone. Conduit i s fo r Gai-tronics , not an issue. S i de 1 Photo Side 2 Photo No photo required.
| |
| No photo required.
| |
| S k etc h FA: A-13 Side 1 Appendix: 85 Rev i ew Distances
| |
| !Reference M-063-<XXll 7A. Figure 7 2.3-1 ) L1 & L2 Dist. (ft) 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6" Pipe Temp. R1 Radius (o f) (in) 1659 4.3 1431 3.3 1236 2.4 1069 1.7 925 1 803 0.5 698 Contact 608 531 464 408 359 FA: A-29 5 de2 R2 Radius (in) 5.7 4.6 3.8 3 2.4 1.8 1.3 0.9 0.6 0.3 0 Contact M-663-00017A
| |
| , R ev isioo WOJ P ag e 8 5-1 9 of 8--4 Penetration Seal Data Appendix: B5 Penetration
| |
| #: P135W2449 Penetration Type: M-1 Fire Area (Side 1): A-29 F ir e Area (Side 2): A-30 Loc./Eiev.: 2009'-9" M-OX Dwg: M-1X1932 1. Barrier Thickness:
| |
| * 24" 10. Annul a r G a p (sm a ll e s t): 1/2" 2. Open i ng Size: 10"D 11. Gap between pe n: N/A 3. Pene t rants: (1) 6"P 1 2. Barrier Type: A F w 4. Seal a nt Type: Foam 13. Open ing Sleeve d or Concrete: Ste el 5. Damm i ng Side1: 1/4" recessed 14. Pipe I n s ul ated: No 6. Damming S i de 2: ** Unknown Wayne Arego od 7. Damming Cont i nu i ty (Acc/Rej): ** Accept Prepared B y: 8. Boot Condition (Acc/Re j): N/A Je ff S ute r 9. Sealant Depth: Assumed Per Detail Reviewe d By: Walkdown Comments:
| |
| * Ba r r ie r thickness determ i ned by D rawing C-1 C1151 ... Th i s ba rri er is u nique i n that incorp orates a 1 0" continuous sleeve too the 2nd compartment w i thin thi s fire a re a. S ide 2 can not be measured. Also see Deta i l on draw i ng M-1X1932. Sketc h: FA: A-29 S l de1 P135W1449 10 9
| |
| ?t'Pe Sc..etil/6 (
| |
| FA: A-30 Slde2 M-663-00017A , R evisi on WOJ Penetration Seal Data Appendix: B5 Photos: P135W2449 Fire Area A-29 (S id e 1) Rre Area A-29 (Sid e 1) F ire Area A-30 (Side 2) Fire Area A-30 (S ide 2)
| |
| M-663-00017A R evis ion WOJ Penetration Seal Data Heat Affected Zone Review: P135W2449 Fire Area (Side 1) A-29 1 No circuit or combustibles i ssues with i n Heat Af f ected Zone 2. 1" copper pipe. not an i ssue Fire Area (Side 2) A-30 3. 1" copper pipe , not an issue , no other i ssues withi n Heat Affected Zone Side 1 Photo Sketch FA: A-29 Side 1 Side 2 P h oto "'l> .. , ** P' ', * * * .t> *
| |
| * v ... -. 1* t>. r7 , ... ' . ._ Appendix: BS Review Distances (Reference M-663-000HA.
| |
| 7.2.3-1 ) 6" Pipe L1 & L2 Temp. R1 Radius R2 Rad iu s D i st. (ft) c*F l (in) (in) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 1.5 1236 2.4 3.8 2 1069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 Contact 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 5.5 408 0 6 359 Contact A*A Side 2 M-663-0001 7A Revision WOJ Penetration Seal Data Appendix: B5 Penetration
| |
| #: P154S1267 Penetration Type: M-1 F ir e Area (Side 1): A-1 9 Fire Area (Side 2): A-16 Loc./Eiev.:
| |
| 204 7'-6" M-OX Dwg: M-1 X 1541 1. Barrier Thickness: 12" 10. Annular Gap (smallest)
| |
| :
| |
| * 3/8" 2. Opening Size: 1 4"D 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 6"P 12. Barrier Type: F 4. Seala nt Type: Foam 13. Opening Sleeved or Concrete: Steel 5. Damm in g Side1: Assumed per de tail 14. Pipe Insulated:
| |
| Yes 6. Damming Side 2: Assumed per detai l Jeff Suter 7. Damming Continu it y (Acc/Rej): Assumed per deta i l Prepared By: 8. Boot Condition (Acc/Rej): NJA Wayne Aregood 9. Sealant Depth: Assumed per detai l Reviewed By: Walkdown Comments: Slab t h ickness i s based on drawing C-1 C 1511. In su l ation covers penetration opening on both barrier sides.
| |
| * Original inspection records i ndicated X dimens ion as 3/8". Sketch: FA: A-19 Slde1 P154S1267 FA: A*16 Side 2 Penetration Seal Data Append i x: 85 Photos: P154S1267 Fire Area A-1 9 (S ide 1 ) Fire Area A-1 9 (S ide 1 ) F ire Area A-16 (Side 2) Fire Area A-16 (Side 2)
| |
| M-663-0 00 17A , R evisio n WO J Pa ge 8--24 of 8 -48 Penetration Seal Data Appendix: B5 Heat Affected Zone Review: P154S1267 Fire Ar ea (S i de 1) A-19 R e view Dist a nces (Reference 723-1) No i ssues w i th i n Heat Affected Zone 6" P i pe L1 & L2 T emp. R1 Rad i us R2 R a d ius D i st. (ft) (" F) (i n) (i n) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 F ire A rea (S i de 2) A-16 1.5 1236 2.4 3.8 No i ssues w i th i n Heat Affected Z o ne 2 1069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 C ontact 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 S i d e 1 Ph o t o S i d e 2 P h o t o 5.5 408 0 6 359 C ontact No photo required.
| |
| No photo required.
| |
| S ketch No sketch required.
| |
| M-663-000 17 A R ev ision WO I P age 85-25 of BS-4 Penetration Seal Data Appendix: B5 Penetration
| |
| #: P321S0081 Penetration Type: M-1 Fire Area (S i de 1 ): C-5 Fire Area (S i de 2): C-1 Loc./Eiev.: 1984'-0" M-OXDwg: M-1X3211 1. Barrier Thickness: 8" 10. Annu l ar Gap (smallest): 1-1/4" 2. Opening Size: 8"0 11. Gap between pen: N/A 3. Pe n etrants: (1) 5"P 12. Barrier Type: F 4. Sealant Type: Foam 13. Opening Sleeved or Concrete: Concrete 5. Damm i ng Side1: N/A 14. Pipe I n su l ated: No 6. Damming Side 2: F l ush w/Q-Deck Va ll ey Wayne Aregood 7. Damming Continu i ty (Acc/Rej): Accept Prepared By: 8. Boot Condition (Acc i Rej): N/A Jeff Suter 9. Sealant Depth: 7" Reviewed By: Walkdown Comments:
| |
| Slab thickness based on drawing C-1 C3211. Top s i de or pe n etration is w i t hin a small CMU wa ll (embedded) p i pe chase. Top side with i n small p i pe chase ha s approx. 10" of ti ghtly packed concrete rubb l e and t he sea l int erface can not be i nspected. Sketch: FA:. C*5 Sldo t P321S0081
| |
| ** .6 E-. ,o.l>' &1-'
| |
| * J I ---.-..:.-
| |
| .. r 0 *
| |
| * 2" FA: C-1 Si<M2 10''
| |
| M-663-00017A , Revision WOJ Penetration Seal Data Appendix:
| |
| 85 Photos: P321S0081 F i re Area C-5 (S i de 1) F i re Area G-5 (Side 1) F i re Area C-1 (S i de 2) F i re Area C-1 (Side 2)
| |
| M-663-0001 7 A R ev i s ion WOJ Pag 85-27 of B--4 Penetration Seal Data Appendix: 85 Heat Affected Zone Review: P321S0081 Fire Area (Side 1) C-5 Rev i ew Distances (Rererence M-663-00017A.
| |
| Ftgu"' 7.23-1 ) No issues within Heat Affected Zone 5" Pipe L1 & L2 Temp. R1 Rad iu s R2 Radius D i st. (ft) (" F) (in) (in) 0.5 1641 4.2 5.6 1 1400 3.2 4.5 F i re Area (S i de 2) C-1 1.5 1196 2.2 3.6 No issues within Heat Affected Zone 2 1024 1.5 2.8 2.5 877 0.8 2.2 3 754 0.2 1.6 3.5 649 Contac t 1.1 4 560 0.7 4.5 485 0.4 5 421 0.1 Side 1 Photo S i de 2 Photo 5.5 368 Conta c t No photo required.
| |
| No photo required.
| |
| Sketch No sketch required.
| |
| M-663-00017A , R ev ision WOI Penetration Seal Data Appendix: BS Penetration
| |
| #: P331W0162 Penetration Type: M-1 Fire Area (Side 1): C-9 Fire Area (Side 2): C-1 0 Loc./Eiev.: 2008"-7 M-OX Dwg: M-1 X0339 1. Barrier Thickness: 1 2" 10. Annular Gap (smallest):
| |
| 3/4" 2. Opening Size: 10"0 11. Gap between pen: N/A 3. Penetrants:
| |
| (1) 6" P 12. Barrier Type: F 4. Sealant Type: Foam 13. Opening Sleeved or Concrete: Stee l 5. Damming Side1: Flush 14. Pipe Insulat ed: No 6. Damming Side 2: 2-1/2" recessed Wayne Aregood 7. Damming Continuity (Acc/Rej):
| |
| Accept Prepared By: 8. Boot Condition (Acc/Rej):
| |
| N/A Jeff Suter 9. Sealant Depth: 7-1/2" Reviewed By: Walkdown Comments:
| |
| Barr ier thicknes s determined by Draw in g 1 0466-A-1325 and by field measurement.
| |
| Sketch: FA: C-.9 S de1 P331W0 162 .... -... * .*. ,/ *: *-: ... I .. t, , : * " ..: , .. FA: C-10 Slde2 M-663-00017A R evision WOI Pa ge B--29 of 85-48 Penetration Seal Data Appendix: 85 Photos: P331W0162 Fi r e Area C-9 (Side 1) Fire Area C-9 (S i de 1) Fire Area C-1 0 (S ide 2) Fire Area C-10 (Side 2)
| |
| M-663-00017A R e vision WOJ P age 85-3 0 of 85-4 Penetration Sea l Data Appendix:
| |
| 85 Heat Affected Zone Review: P331W0162 Fire Area (Side 1) C-9 Review Distances (Referen ce M-663-00017 A, Fog ur e 7.2 3-1 ) N o i ssues w i th in Hea t A ff ected Zo n e 6" Pipe L1 & L2 Temp. R1 Radius R2 Radius D i s!. (ft) (*F) (in) (in) 0.5 1 659 4.3 5.7 1 1 4 31 3.3 4.6 Fire Area (Side 2) C-10 1.5 123 6 2.4 3.8 2 No i ssues w i thi n Heat A f fected Zo n e 1 06 9 1.7 3 2.5 9 25 1 2.4 3 803 0.5 1.8 3.5 698 C o nt ac t 1.3 4 608 0.9 4.5 53 1 0.6 5 46 4 0.3 Side 1 Photo S i de 2 P h oto 5.5 4 08 0 6 359 Con tac t N o photo required.
| |
| No photo required.
| |
| Sketc h No sk etch r e q uired a M-663-00017A Revision WOI Penetration Seal Data Penetration
| |
| #: Penetration Type: Loc./Eiev.: 2 0 2 5'-2 1 1. Barrier Thickness: 2. Opening Size: 3. Penetrants
| |
| : 4. Sealant Type: 5. Damming Side1: P341W0209 M-1 8" Nominal 10"0 (1) 6" P Foam Flush 6. Damming Side 2: Flush 7. Damming Continuity (Acc/Rej):
| |
| Accept 8. Boot Condition (Acc/Rej): N/A 9. Sealant Depth: 6" Nomi n a l Walkdown Comments:
| |
| Sketch: Appendix: BS Fire Area (Side 1 ): C-35 M-OX Dwg: M-1 X 03 4 0 F i re Area (Side 2): C-13 10. Annular Gap (smallest)
| |
| : 1-1/4" 11. Gap between pen: N/A 12. Barrier Type: F 13. Opening Sleeved or Concrete: 14. Pipe Insulated: No Wayne Aregood Prepared By: Jeff Suter Reviewed By: Steel M-663-00017A , R evisi on WOJ P age 85-32 of BS-4 Penetration Seal Data Appendix: 85 Photos: P341W0209 Fire Area C-35 (S ide 1) F ire Area C-35 (S ide 1) y 11 F ire Area C-1 3 (Side 2) F ire Are a C-13 (S id e 2)
| |
| M-663-0001 7 A , R ev i s i o n WO J P age BS-33 o f 8 5-4 Penetration Seal Data Appendix: 85 Heat Affected Zone Review: P341W0209 F i re Area (Side 1) C-35 Review Distances (Referen<:e M-663-00017A ,
| |
| 72.3-1) No issues within Hea t A ff e c ted Zo n e 6" Pipe L1 & L2 Temp. R1 Radius R2 Radius Dist. (ft) (" F) (in) (in) 0.5 16 59 4.3 5.7 1 1 4 31 3.3 4.6 Fire Area (Side 2) C-13 1.5 1 2 36 2.4 3.8 2 No I ssues with i n Heat A ff ected Zone 1069 1.7 3 2.5 92 5 1 2.4 3 803 0.5 1.8 3.5 698 C onta ct 1.3 4 608 0.9 4.5 5 31 0.6 5 4 64 0.3 Side 1 Photo Side 2 Photo 5.5 4 08 0 6 359 C on tact No photo required.
| |
| No photo required.
| |
| S k etc h No sketch require d.
| |
| M-66 3-000 17 A , R e vi s ion WO I P age 85-34 of 8--48 Penetration Seal Data Appendix:
| |
| B5 Penetration
| |
| #: P341W0216 Penetration Type: M-1 Fire Area (Side 1): C-35 Fire Area (S i de 2): C-14 Loc./Eiev.: 2024'-9 1 M-OX Dwg: M-1X0340 1. Barrier Thickness:
| |
| 8" Nominal 10. Annular Gap (smallest)
| |
| : 1" 2. Opening Size: 1 0"0 11. Gap between pen: N/A 3. Penetrants:
| |
| (1) 6"P 12. Barrier Type: F 4. Sealant Type: Foam 13. Opening Sleeved or Co n crete: Steel 5. Damm i ng Side1: F l ush w/ s l eeve (+3/8") 14. P i pe In s ul a t ed: No 6. Damm i ng Side 2: Flush Wayne Aregood 7. Damming Continu i ty (Acc/Rej): Accept Prepared By: 8. Boot Condition (Acc/Rej):
| |
| N/A Jeff Suter 9. Sealant Depth: 6" Nom i nal Reviewed By: Walkdow n Comments: Sketch: FA: C-35 Side 1 M-663-00017A , R evision WOJ P age s--35 ofBS-4 8 Penetration Seal Data Appendix: 85 Photos: P341W0216 Fi re Area C-35 (Side 1) F i re Area C-35 (Side 1 ) F ir e Area C-14 (Side 2) Fire Area C-1 4 (Si de 2)
| |
| M-663-00017A R e vision WOI Penetration Seal Data Heat Affected Zone Review: P341W0216 Fire Area (Side 1) C-35 1. 5U3027 , 2" Cond: Within Heat Affected Zone. Further review determined tha t this Condu i t it is not ded i cated PFSSD. Set-route control necessary. Fire Area (Side 2) C-14 No issues within Hea t Affected Zone S i de 1 Photo S i de 2 Photo No photo requ i red. No photo required.
| |
| Sketch F A: c-36 S i d e 1 " _, Appendix:
| |
| 85 Review Distances (Refe<eoce M-663-00017A.
| |
| FJQ ure 7 .2.:>-1 ) L 1 & L2 D i s t. (ft) 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6" P i p e T e mp. R 1 Ra di us (" F) (in) 1659 4.3 1431 3.3 123 6 2.4 1069 1.7 9 2 5 1 803 0.5 698 C ontact 608 531 464 408 359 FA: C.14 Slde2 R2 Rad iu s (in) 5.7 4.6 3.8 3 2.4 1.8 1.3 0.9 0.6 0.3 0 Con t a ct M-663-000 17 A Re vis ion WO I Penetration Seal Data Appendix:
| |
| B5 Penetration
| |
| #: P341W0227 Penetration Type: M-1 Fire Area (Side 1): C-35 Fire Area (Side 2): C-16 Loc./Eiev.: 2024'-7 1 M-OX Dwg: M-1 X0340 1. Barrier Thickness: 8" Nominal 10. Annular Gap (smallest):
| |
| 1 1/4" 2. Opening Size: 10" 0 11. Gap between pen: N/ A 3. Penetrants
| |
| : (1) 6"P 12. Barrier Type: F 4. Sealant Type: Foam 13. Opening Sleeved or Concrete:
| |
| Stee l 5. Damming Side1: F l ush w/sleeve (+318") 14. Pipe Insulated: No 6. Damming Side 2: Flush 7. Damming Continuity (Acc/Rej): Accept 8. Boot Condition (Acc/Rej):
| |
| N/A 9. Sealant Depth: Walkdown Comments: Sketch: FA: C-35 Side 1 6 3/8" t Wayne Aregood Prepared By: Jeff Suter Reviewed By:
| |
| M-663-0001 7 A R ev i sio n W OI P age 85-38 of B--4 Penetration Seal Data Appendix: BS Photos: P341W0227 F i re Are a C-35 (Side 1) F i re Area C-35 (Side 1) Fi re A rea C-16 (S ide 2) Fire Area C-16 (S i de 2)
| |
| M-663-00017A
| |
| , R evisi on WOJ Pa ge B--39 of 85-4 Penetration Seal Data Appendix:
| |
| 85 Heat Affected Zone Review: P341W0227 Fire Area (Side 1) C-35 Review Distances (Reference 1 7 A. F tgure 7 .2.3-1 ) No issues w i t hin Heat Affected Zone 6" P i pe L 1 & L2 Temp. R1 Ra di us R2 Radius D i s t. (ft) (" F) (in) (in) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 Fire Area (Side 2) C-16 1.5 1 236 2.4 3.8 No iss u es w ithi n Heat Affected Zone 2 1069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 Contact 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 Side 1 Photo Side 2 Photo 5.5 408 0 6 359 Con tact No photo required.
| |
| No photo required.
| |
| Sketch No sketch required.
| |
| M-663-00017 A , R evisi on WOJ P age 8 5-40 of 85-4 Penetration Seal Data Appendix:
| |
| BS Penetration#:
| |
| P341W0250 Penetration Type: M-1 Fire Area (Side 1 ): C-3 5 Fire Area (S i de 2): C-15 Loc./Eiev.:
| |
| 2025'-1 5 M-OX Dwg: M-1X0340 1. Barrier Thickness: 8" Nomina l 10. Annular Gap (smallest)
| |
| : 3/4" 2. Opening Size: 10"D 11. Gap between pen: N/A 3. Penetrants:
| |
| (1) 6" P 12. Barrie r Type: F 4. Sealant Type: Foam 13. Openi ng Sleeved or Concrete: Stee l 5. Damming Side1: F l ush w/sleeve (+1/4") 14. Pipe Insulated:
| |
| No 6. Damming Side 2: Flush 7. Damming Cont inuit y (Acc/Rej): Accept 8. Boot Condition (Ace/Rei): N/A 9. Sealant Depth: 6 1/4" Nom inal Walkdown Comments: Sketch: FA; C-35 Side 1 Wayne Are go od Prepared By: Jeff Suter Reviewed By:
| |
| M-663-0001 7 A , R ev i s i o n W OJ Penetration Seal Data Appendix: 85 Photos: P341W0250 F i re Area C-35 (Side 1} F ir e Area C-35 (S i de 1} Fi re A r ea C-15 (S i de 2} F ire A r ea C-1 5 (S id e 2}
| |
| M-663-000 17 A , R ev i s ion WO I Penetration Seal Data Heat Affected Zone Review: P341W0250 Fire Area (Side 1) C-35 1. 6C3073 , 1/2" EMT (FP), No i ssue 2. 6C3054 , 1/2" EMT (FP). No i ssue 3. 6 C 3050. 1/2" EMT (FP), No issue 4. 6C3049 , 1/2" EMT (FP). No i ssue 5. 6C3051 , 1/2" EMT (FP), No iss ue Fi r e Area (Side 2) C-1 5 No issues within Heat Affected Zone S i de 1 Photo Side 2 Photo No photo required.
| |
| No photo required.
| |
| Sketch FA: C-35 Slda1 Page 85-42 of 85-48 Appendix:
| |
| BS Review Distances (Reference M-663-00017 A. Fogure 7.2.3-1 ) 6" Pipe L1 & L2 Temp. R1 Radius R2 Radius D i st. (ft) (o F) (in) (in) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 1.5 1236 2.4 3.8 2 1069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 Contact 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 5.5 408 0 6 359 Contact F=:=:::::=:=t,....,..:
| |
| :.__c ""u W4 L L F A: C-1 5 S lde 2 M-663-00017A R e vi s ion WOI Page 8--43 of BS-48 Penetration Seal Data Appendix: 85 Penetration
| |
| #: P351S0371 Penetration Type: M-1 Fire Area (Side 1 ): C-21 Fire Area (Side 2): C-16 Loc./Eiev.: 203 2'-0" M-OXDwg: M-1 X35 11 1. Barrier Thickness: 8" 10. Annular Gap (sma ll es t): 1-1/4" 2. Opening Size: 10"0 11. Gap between pen: N/A 3. Penetrants:
| |
| (1) 6" P 12. Barrier Type: F w 4. Sea l a n t Type: F oam 13. Open in g Sleeved o r Conc r ete: Steel 5. Damm i ng Side1: Foa m 1" above S lab 14. Pipe In s ul ated: No 6. Damm i ng Side 2: Flush 7. Damming Cont i nu i ty (Acc/Rej): Accept 8. Boot Condit i on (Acc/Rej): N/A 9. Sealant Depth: 8" Walkdown Comments: B arr i er th i ckness dete r m in ed by Draw in g C-O C35 1 1. Sketch: FA: C-21 Sldo 1 P351S0371 Wayne Aregood Prepared By: Jeff Suter Reviewed By: FA: C*16 Slde2 M-663-00017A , R evision WOJ Pag e B--44 of BS-48 Penetration Seal Data Appendix: 85 Photos: P351S0371 Fire Area C-2 1 (S ide 1) F i re Area C-21 (S ide 1) Fire Area C-16 (S ide 2) F ir e Area C-16 (Side 2}
| |
| M-663-000 I?A R e vision WO J P age 8 5-45 of 85-48 Penetration Seal Data Append i x: BS Heat Affected Zone Review: P351S0371 F ire Area (S ide 1) C-21 Review Dist anc es (Reference M-66:;.oo()17A, Fogure 7.2.3-1) No 1ss u es w1 t hin Heat Affe ct e d Zon e 6" Pipe l1 & l2 Temp. R1 Radius R2 Radius Dist. (ft) (*F) (in) (in) 0.5 1659 4.3 5.7 1 1431 3.3 4.6 F i re Area (Side 2) C-16 1.5 1236 2.4 3.8 No i ssu e s w ith in Hea t Affe c te d Z on e 2 1069 1.7 3 2.5 925 1 2.4 3 803 0.5 1.8 3.5 698 C ontact 1.3 4 608 0.9 4.5 531 0.6 5 464 0.3 Side 1 Photo S ide 2 Photo 5.5 408 0 6 359 Contact No pho to r equ ir ed. No photo required.
| |
| Sketch No sketch required.
| |
| M-663-00017A, Revision WOl Page 85-46 of 85-48 Penetration Seal Data Appendix:
| |
| B5 Penetration
| |
| #: P611W0083 Penetration Type: M-1 Fire Area (Side 1): F-2 Fire Area (S i de 2): F-3 Loc./Eiev.:
| |
| 2020'-1 1 M-OX Dwg: M-1X6906 1. Barrier Thickness:
| |
| 12" 10. Annular Gap (smallest):
| |
| 1-1/4" 2. Opening Size: 10"0 11. Gap between pen: N/A 3. Penetrants
| |
| : (1) 6" P 12. Barrier Type: F 4. Sealant Type: Foam 13. Openi ng Sleeved or Concrete:
| |
| S t ee l 5. Damming Side 1: 3" recessed 14. Pipe Insulated: No 6. Damming Side 2: F lu sh Wa y ne A regood 7. Damming Cont inuit y (Acc/Rej):
| |
| A cc e pt Prepared By: 8. Boot Cond it ion (Acc/Rej): N/A Je ff Sut e r 9. Sealant Depth: 7" Reviewed By: Walkdown Comments: Wall th i ckness de t ermi n ed b y Draw i ng C-1 C61 11. Sketch: FA.: F-.2 Side 1 P611W0083
| |
| * .j I> .. i
| |
| * FA: F-3 Slde2 M-663-00017 A, R evis i on W O J Page 8--4 7 of BS-48 Penetration Seal Data Appendix: 85 Photos: P61 1 W0083 F i re Area F-2 (Side 1) Fire Area F-2 (Side 1) Fire Area F-3 (Side 2) F ire Area F-3 (Side 2)
| |
| M-663-00017A , R e vision WOI P age 85-48 of B--4 8 Penetration Seal Data Appendix:
| |
| BS Heat Affected Zone Review: P611W0083 Fire Area (Side 1) F-2 Review Distances (Refe r ence Ftgure 72.3-1) No iss u es wit h in Heat Affe c te d Z on e 6" Pipe L1 & L2 Temp. R1 Radius R2 Radius D i st. (ft) (" F) (in) (in) 0.5 1 659 4.3 5.7 1 14 3 1 3.3 4.6 Fire Area (Side 2) F-3 1.5 1 2 3 6 2.4 3.8 No is s ues withi n Hea t Affe c te d Zone 2 1 069 1.7 3 2.5 92 5 1 2.4 3 803 0.5 1.8 3.5 698 C ontact 1.3 4 608 0.9 4.5 531 0.6 5 4 64 0.3 Side 1 Photo Side 2 Photo 5.5 4 08 0 6 359 C o nta ct No photo r equired. No p hoto required.
| |
| Sketch No ske ch required.
| |
| i CREEK OPERATING CORPORATION M-663-00017 A Attachment 86 Fire Protection Evaluation For Penetrant Size Exceeding Typical Detail M -6A Limitation Rev. No. Prepared By Date Reviewed By W01 Jeff Suter Wayne S Aregood 08/19/05 Page 1 Date 08/19/05 M-663-000 17 A Attachment 86 Revision WO 1 Table of Contents Page 2 of7 Revision Log ...................................................................................................................................
| |
| 3 1.0 Purpose ...............................................................................................................................
| |
| 4 2.0 Scope ..................................................................................................................................
| |
| 4 3. 0 References
| |
| ..........................................................................................................................
| |
| 4 4.0 Evaluation
| |
| ...........................................................................................................................
| |
| 5 5.0 Conclusions
| |
| .........................................................................................................................
| |
| 7 Appendix 86, Penetration Seal Data .......................
| |
| ,, ............................
| |
| (24 Total Pages)
| |
| M-663-00017 A Attachment 86 Revision W01 Revision Reason for Revision W01 Original Issue Page 3 of 7 Revision Log M-663-00017 A Attachment B6 Revision W01 1.0 Purpose Page 4 of? 1.1 The purpose of this document is to evaluate existing penetration seals that are not directly bounded to the typical detail limitations established in M-663-00017.
| |
| This evaluation was conducted in effort to satisfy regulatory expectation regarding qualification and documentation of fire barrier penetration seals, as discussed in NRC Information Notice 88-04. This evaluation was conducted in accordance with the guidance of NRC Generic Letter 86-10. 2.0 Scope 2.1 The Table I penetrations in relation to the design requirements discussed in Section 5.1. 2.2 Refer to Section 7.0 of M-663-00017 A for a cross-reference list of penetrations within Table I that are evaluated for additional seal parameters that do not satisfy the typical detail limitations of M-663-00017.
| |
| In these instances, the potential cumulative affects of multiple unbounded attributes were considered for each penetration of concern. 3.0 References 3.1 NRC Generic Letter 86-10, Implementation of Fire Protection Requirements, dated April24, 1986 3.2 NRC Information Notice 88-04, Inadequate Qualification and Documentation of Fire Barrier Penetration Seals 3.3 10 CFR 50 Appendix R, Fire Protection Program For Nuclear Power Facilities Operating Prior To January 1, 1979 3.4 LER 87-10, Technical Specification
| |
| \Aolations
| |
| -Inoperable Fire Barriers Caused By Personnel Errors 3.5 M-663-00017, Penetration Seal Typical Details 3.6 Fire Test CTP-1009 (M-663-00148), 9" Depth 3-6548 Silicone RTV Foam w/Site Specific SNUPPS Cable and Repair 3.7 Fire Test IC01091035 (M-663-00156), 3 Hour Fire Resistance Evaluation of Ten Different Penetration Seal Designs 3.8 Fire Test M-663-00161, 3-Hour Fire Resistance Evaluation Of Twelve Different Fire Penetration Seal Designs Contained Within Two Different Test Slabs M-663-00017 A Attachment 86 Revision W01 Page 5 of 7 4.0 Assumptions 4.1 It is assumed that existing penetration seal materials have been installed as required by applicable typical design details and procedures.
| |
| This is an acceptable assumption based on a review of the Quality Control documentation maintained during initial penetration seal installation activities and the intrusive inspections conducted to address LER 87-10, regarding seal material depth. 5.0 Evaluation 5.1 Assessment of Condition to Design Requirements The penetration openings identified in Table I contain a pipe penetrant that exceeds the size limitation directly bounded by typical detail M-6A. The M-6A typical detail, which is comprised of a 9" (min.) Silicone Foam and ceramic fiber damming, directly qualifies a seal with up to a 1 0" diameter penetrant as 3-hour fire (F) and temperature (T) rated. TABLE I M-6A Penetrations with Penetrant Size Exceeding Typical Detail Limitations
| |
| *-. -* .. Penetration Communicating Penetration Pipe Silicone Comments/
| |
| Number Fire Areas Orientation Penetrant Foam Disposition Side 1 Side 2 Diameter Depth P131S0491 A-8 A-1 Floor/Ceiling 12" 9" See 5.2 P133S0780 A-8 A-1 Floor/Ceiling 12" 9" See 5.2 P133S0781 A-8 A-1 Floor/Ceiling 12" 12-1/2" See 5.2 P141W2487 A-16 A-26 Wall 12" 10" See 5.2 P142S1079 A-16 A-8 Floor/Ceiling 12" 15-1/2" See 5.2 P151S1196 A-20 A-26 Floor/Ceiling 12" 12" See 5.2 P153W2557 A-19 A-20 Wall 12" 9-1/2" See 5.2 P621S0161 F-4 F-2 Floor/Ceiling 12" 11" See 5.2 5.2 Evaluation of Condition The Table I penetrations are determined to be 3-hour F rated based on comparison to Penetration 11 from fire test report M-663-00161 and a review of the M-663-00017 penetrant size evaluation for detail M-6A. Penetration 11 was a 20" diameter opening sealed with a 12" depth of Silicone Foam and no damming. It contained a 16" diameter pipe penetrant.
| |
| The tested configuration successful prevented the passage of flame and hot gases to the unexposed side for a 3-hour fire exposure duration.
| |
| However, it did not pass the required post burn hose stream test. The primary reason for the unsuccessful hose stream test was that the seal configuration did not incorporate friction fitted damming, and a significant quantity of Silicone Foam was consumed during the fire exposure.
| |
| M-663-00017 A Attachment 86 Revision W01 Page 6 of 7 A review of the M-663-00017 penetrant size evaluation for detail M-6A identifies that fire tested parameters, such as penetrant size, for 12" Silicone Foam seals were determined to be acceptable for bounding detail M-6A limitations based on the similar unexposed side free area thermal performance of the following fire tested configurations:
| |
| * Blackout from CTP-1009, sealed with 9" of Silicone Foam over 1" ceramic fiber damming.
| |
| * Penetration 3 from IC01091035, sealed with 12" of Silicone Foam. The comparable free area thermal performance of these two tested configurations substantiates that the fire resistive capability of ceramic fiber is superior to Silicone Foam, predominantly because ceramic fiber does not char (unlike Silicone Foam), when directly subjected to flame exposure.
| |
| Considering the presence of ceramic fiber damming on the bottom side for floor/ceiling applications and both barrier sides for wall applications, it is reasonable to conclude that the Table I penetrations will prevent both the passage of flame and hose stream to the unexposed side of the seal, thus satisfying a 3-hour F rating. The Table I penetrations are not considered T rated, as the unexposed side seal surface temperatures for Penetration 11 from M-663-00017 exceeded the Wolf Creek 3-hour T rating unexposed side seal surface temperature limitation of 325°F plus ambient. The maximum seal surface temperature exhibited by the test assembly was 647°F. M-663-00017 identifies that where piping penetrations exist that do not satisfy T rating requirements, a seal assembly with an F rating corresponding to the hourly rating of the associated barrier is acceptable, provided evaluation demonstrates that exposed insitu combustibles and redundant post fire safe shutdown (PFSSD) equipment/circuits on the unexposed barrier side will not be detrimentally affected by the increased penetrant temperatures.
| |
| In effort to evaluate fire area impact, field walkdowns and comprehensive assessment reviews, documented in Appendix ro-1, were conducted for each penetration of concern. This review was completed in accordance with the criteria and review methodology established in M663-00017A Section 7.2.3 for non-T rated penetrations.
| |
| The review identified that no exposed insitu combustibles or PFSSD circuits are located within the heat affected zone. Each of the penetrations satisfies the review criteria of M-663-00017 where T rating requirements are not met. Therefore, the penetrations are acceptable, as this evaluation demonstrates reasonable assurance that the penetration seals do not present a negative impact to PFSSD capability.
| |
| M-663-00017 A Attachment 86 Revision WO 1 5.3 Post Fire Safe Shutdown Impact Page 7 of? There is no impact to PFSSD systems or components as a result of this evaluation.
| |
| The Table I penetrations are 3-hour F rated. The comprehensive walkdown review for each of these penetrations revealed that no exposed insitu combustibles or PFSSD circuits are regatively affected by the non T rated penetrations.
| |
| 6.0 Conclusions Based on the above discussions, it is reasonable to conclude that the Table I penetration seals are acceptable as 3-hour F rated and will perform their intended function, regardless of not achieving a T rating. The penetration seals satisfy regulatory requirements and commitments as well as WCNOC Fire Protection Program requirements, to prevent spread of fire from one fire area to another. It has also been determined through this evaluation that the lack of a T rating will not affect the plant's ability to achieve and maintain PFSSD.
| |
| M-66 3-00017A R ev ision WOJ Penetration Seal Data Penetration#:
| |
| Penetration Type: Loc./Eiev.: 2000'-0" 1. Barrier Thickness: 2. Opening Size: 3. Penetrants:
| |
| : 4. Seala n t Type: P131S0491 M-6A 1 0" 16"0 (1) 12"P Foam P age 8 6-J of 86-24 Appendix:
| |
| B6 F i re Area (Side 1 ): A-8 F i re Area (Side 2): A-1 M-OXDwg: M-1X1311 10. Annular Gap (smallest): 3/4" 11. Gap between pen: N/A 12. Barr i e r Type: F 13. Opening Sleeved or Co n crete: Steel 5. Damm i ng Side1: Foam even with slab 14. Pipe In s ul ated: No 6. Damm i ng Side 2: F l ush w/c e i ling 7. Damm i ng Continu i ty (Ace/Rei): Accept 8. Boot Condition (Ace/Rei): N/A 9. Sealant Depth: 9" Walkdown Comments: Slab thickness based on C-1C1311.
| |
| Changed Detail M-1 to M-6A Sketch: FA: A.-8 Side 1 P131S0491 Wayne Aregood Prepared By: Jeff Suter Reviewed By: FA: A*1 Slde2 M-6 6 3-00017A , R evision WOl P age 8 6-2 of B 6-2 4 Penetration Seal Data Append i x: 86 Photos: P131S0491 F ire A r ea A-8 (S i de 1) F i re Area A-8 (Side 1) F i re Area A-1 (Side 2) F ir e Area A-1 (Side 2)}}
| |
