ML22319A229: Difference between revisions

From kanterella
Jump to navigation Jump to search
(StriderTol Bot insert)
 
(StriderTol Bot change)
 
Line 19: Line 19:


=Text=
=Text=
{{#Wiki_filter:HalfPACT Safety Analysis Report Revision 9 August 2022
{{#Wiki_filter:}}
 
This page intentionally left blank.
HalfPACT Safety Analysis Report                                                                        Rev. 9, August 2022 TABLE OF CONTENTS 1.0 GENERAL INFORMATION ........................................................................................ 1.1-1 1.1 Introduction .............................................................................................................. 1.1-1 1.2 Package Description ................................................................................................. 1.2-1 1.2.1 Packaging ..................................................................................................... 1.2-1 1.2.1.1 Packaging Description ................................................................... 1.2-1 1.2.1.2 Gross Weight ................................................................................. 1.2-4 1.2.1.3 Neutron Moderation and Absorption ............................................ 1.2-5 1.2.1.4 Receptacles, Valves, Testing, and Sampling Ports ....................... 1.2-5 1.2.1.5 Heat Dissipation ............................................................................ 1.2-5 1.2.1.6 Coolants ......................................................................................... 1.2-6 1.2.1.7 Protrusions ..................................................................................... 1.2-6 1.2.1.8 Lifting and Tie-down Devices ....................................................... 1.2-6 1.2.1.9 Pressure Relief System .................................................................. 1.2-7 1.2.1.10 Shielding........................................................................................ 1.2-7 1.2.2 Operational Features..................................................................................... 1.2-7 1.2.3 Contents of Packaging .................................................................................. 1.2-7 1.3 Appendices ............................................................................................................... 1.3-1 1.3.1 Packaging General Arrangement Drawings .............................................. 1.3.1-1 1.3.2 Glossary of Terms and Acronyms ............................................................. 1.3.2-1 2.0 STRUCTURAL EVALUATION ................................................................................... 2.1-1 2.1 Structural Design ...................................................................................................... 2.1-1 2.1.1 Discussion .................................................................................................... 2.1-1 2.1.1.1 Containment Vessel Structure (ICV) ............................................ 2.1-2 2.1.1.2 Non-Containment Vessel Structures (OCV and OCA) ................. 2.1-3 2.1.2 Design Criteria ............................................................................................. 2.1-3 2.1.2.1 Analytic Design Criteria (Allowable Stresses) ............................. 2.1-3 2.1.2.2 Miscellaneous Structural Failure Modes ....................................... 2.1-4 2.2 Weights and Centers of Gravity ............................................................................... 2.2-1 2.2.1 Effect of a Radial Payload Imbalance .......................................................... 2.2-1 2.2.2 Effect of an Axial Payload Imbalance .......................................................... 2.2-5 2.3 Mechanical Properties of Materials .......................................................................... 2.3-1 2.3.1 Mechanical Properties Applied to Analytic Evaluations ............................. 2.3-1 2.3.2 Mechanical Properties Applied to Certification Testing .............................. 2.3-2 2.4 General Standards for All Packages ......................................................................... 2.4-1 2.4.1 Minimum Package Size ................................................................................ 2.4-1 2.4.2 Tamper-indicating Feature ........................................................................... 2.4-1 i
 
HalfPACT Safety Analysis Report                                                                      Rev. 9, August 2022 2.4.3 Positive Closure............................................................................................ 2.4-1 2.4.4 Chemical and Galvanic Reactions ................................................................ 2.4-1 2.4.4.1 Packaging Materials of Construction ............................................ 2.4-2 2.4.4.2 Payload Interaction with Packaging Materials of Construction .... 2.4-3 2.4.5 Valves ........................................................................................................... 2.4-3 2.4.6 Package Design ............................................................................................ 2.4-3 2.4.7 External Temperatures ................................................................................. 2.4-3 2.4.8 Venting ......................................................................................................... 2.4-4 2.5 Lifting and Tie-down Standards for All Packages ................................................... 2.5-1 2.5.1 Lifting Devices ............................................................................................. 2.5-1 2.5.2 Tie-down Devices......................................................................................... 2.5-2 2.5.2.1 Tie-down Forces ............................................................................ 2.5-2 2.5.2.2 Tie-down Stress Due to a Vertical Tensile Load .......................... 2.5-3 2.5.2.3 Tie-down Stress Due to a Vertical Compressive Load ................. 2.5-7 2.5.2.4 Tie-down Stresses Due to a Horizontal Compressive Load .......... 2.5-8 2.5.2.5 Response of the Package if Treated as a Fixed Cantilever Beam 2.5-10 2.5.2.6 Summary ..................................................................................... 2.5-11 2.6 Normal Conditions of Transport .............................................................................. 2.6-1 2.6.1 Heat .............................................................................................................. 2.6-2 2.6.1.1 Summary of Pressures and Temperatures ..................................... 2.6-2 2.6.1.2 Differential Thermal Expansion .................................................... 2.6-3 2.6.1.3 Stress Calculations ........................................................................ 2.6-3 2.6.1.4 Comparison with Allowable Stresses ............................................ 2.6-4 2.6.1.5 Range of Primary Plus Secondary Stress Intensities ..................... 2.6-5 2.6.2 Cold .............................................................................................................. 2.6-6 2.6.2.1 Stress Calculations ........................................................................ 2.6-6 2.6.2.2 Comparison with Allowable Stresses ............................................ 2.6-7 2.6.3 Reduced External Pressure ........................................................................... 2.6-7 2.6.4 Increased External Pressure.......................................................................... 2.6-7 2.6.4.1 Stress Calculations ........................................................................ 2.6-8 2.6.4.2 Comparison with Allowable Stresses ............................................ 2.6-8 2.6.4.3 Buckling Assessment of the Torispherical Heads ......................... 2.6-9 2.6.4.4 Buckling Assessment of the Cylindrical Shells ............................ 2.6-9 2.6.5 Vibration ..................................................................................................... 2.6-10 2.6.5.1 Vibratory Loads Determination................................................... 2.6-10 2.6.5.2 Calculation of Alternating Stresses ............................................. 2.6-11 2.6.5.3 Stress Limits and Results ............................................................ 2.6-12 2.6.6 Water Spray ................................................................................................ 2.6-12 2.6.7 Free Drop .................................................................................................... 2.6-12 2.6.8 Corner Drop ................................................................................................ 2.6-13 2.6.9 Compression ............................................................................................... 2.6-13 2.6.10 Penetration .................................................................................................. 2.6-13 ii
 
HalfPACT Safety Analysis Report                                                                          Rev. 9, August 2022 2.7  Hypothetical Accident Conditions ........................................................................... 2.7-1 2.7.1 Free Drop ...................................................................................................... 2.7-2 2.7.1.1 Technical Basis for the Free Drop Tests ....................................... 2.7-2 2.7.1.2 Test Sequence for the Selected Tests ............................................ 2.7-3 2.7.1.3 Summary of Results from the Free Drop Tests ............................. 2.7-3 2.7.2 Crush ............................................................................................................ 2.7-3 2.7.3 Puncture ........................................................................................................ 2.7-3 2.7.3.1 Technical Basis for the Puncture Drop Tests ................................ 2.7-4 2.7.3.2 Test Sequence for the Selected Tests ............................................ 2.7-5 2.7.3.3 Summary of Results from the Puncture Drop Tests ...................... 2.7-5 2.7.4 Thermal ........................................................................................................ 2.7-6 2.7.4.1 Summary of Pressures and Temperatures ..................................... 2.7-6 2.7.4.2 Differential Thermal Expansion .................................................... 2.7-8 2.7.4.3 Stress Calculations ........................................................................ 2.7-8 2.7.4.4 Comparison with Allowable Stresses ............................................ 2.7-8 2.7.5 Immersion - Fissile Material ........................................................................ 2.7-8 2.7.6 Immersion - All Packages ............................................................................ 2.7-8 2.7.6.1 Buckling Assessment of the Torispherical Heads ......................... 2.7-9 2.7.6.2 Buckling Assessment of the Cylindrical Shells ............................ 2.7-9 2.7.7 Deep Water Immersion Test....................................................................... 2.7-10 2.7.8 Summary of Damage .................................................................................. 2.7-10 2.8  Special Form............................................................................................................. 2.8-1 2.9  Fuel Rods .................................................................................................................. 2.9-1 2.10 Appendices ............................................................................................................. 2.10-1 2.10.1 Finite Element Analysis (FEA) Models .................................................. 2.10.1-1 2.10.1.1 Outer Confinement Assembly (OCA) Structural Analysis ...... 2.10.1-1 2.10.1.2 Inner Containment Vessel (ICV) Structural Analysis .............. 2.10.1-4 2.10.2 Elastomer O-ring Seal Performance Tests .............................................. 2.10.2-1 2.10.2.1 Introduction .............................................................................. 2.10.2-1 2.10.2.2 Limits of O-ring Seal Compression and Temperature ............. 2.10.2-1 2.10.2.3 Formulation Qualification Test Fixture and Procedure ............ 2.10.2-6 2.10.2.4 Rainier Rubber R0405-70 Formulation Qualification Test Results ...................................................................................... 2.10.2-8 2.10.2.5 ASTM D2000 Standardized Batch Material Tests ................... 2.10.2-8 2.10.3 Certification Tests ................................................................................... 2.10.3-1 2.10.3.1 Introduction .............................................................................. 2.10.3-1 2.10.3.2 Summary .................................................................................. 2.10.3-1 2.10.3.3 Test Facilities ........................................................................... 2.10.3-3 2.10.3.4 Test Unit Description ............................................................... 2.10.3-3 2.10.3.5 Technical Basis for Tests ......................................................... 2.10.3-9 2.10.3.6 Test Sequence for Selected Free Drop, Puncture Drop, and Fire Tests ................................................................................ 2.10.3-19 2.10.3.7 Test Results ............................................................................ 2.10.3-26 iii
 
HalfPACT Safety Analysis Report                                                                        Rev. 9, August 2022 3.0 THERMAL EVALUATION .......................................................................................... 3.1-1 3.1 Discussion ................................................................................................................ 3.1-1 3.1.1 Packaging ..................................................................................................... 3.1-1 3.1.2 Payload Configuration .................................................................................. 3.1-2 3.1.3 Boundary Conditions .................................................................................... 3.1-3 3.1.4 Analysis Summary ....................................................................................... 3.1-4 3.2 Summary of Thermal Properties of Materials .......................................................... 3.2-1 3.3 Technical Specifications of Components ................................................................. 3.3-1 3.4 Thermal Evaluation for Normal Conditions of Transport ........................................ 3.4-1 3.4.1 Thermal Model ............................................................................................. 3.4-1 3.4.1.1 Analytical Model ........................................................................... 3.4-1 3.4.1.2 Test Model ..................................................................................... 3.4-3 3.4.2 Maximum Temperatures .............................................................................. 3.4-3 3.4.3 Minimum Temperatures ............................................................................... 3.4-3 3.4.4 Maximum Internal Pressure ......................................................................... 3.4-3 3.4.4.1 Design Pressure ............................................................................. 3.4-3 3.4.4.2 Maximum Pressure for Normal Conditions of Transport ............. 3.4-3 3.4.4.3 Maximum Normal Operating Pressure........................................ 3.4-10 3.4.5 Maximum Thermal Stresses ....................................................................... 3.4-10 3.4.6 Evaluation of Package Performance for Normal Conditions of Transport 3.4-11 3.5 Thermal Evaluation for Hypothetical Accident Conditions ..................................... 3.5-1 3.5.1 Thermal Model ............................................................................................. 3.5-1 3.5.1.1 Analytical Model ........................................................................... 3.5-1 3.5.1.2 Test Model ..................................................................................... 3.5-1 3.5.2 Package Conditions and Environment ......................................................... 3.5-1 3.5.3 Package Temperatures .................................................................................. 3.5-2 3.5.4 Maximum Internal Pressure ......................................................................... 3.5-3 3.5.5 Maximum Thermal Stresses ......................................................................... 3.5-4 3.5.6 Evaluation of Package Performance for the Hypothetical Accident Thermal Conditions .................................................................................................... 3.5-4 3.6 Appendices ............................................................................................................... 3.6-1 3.6.1 Computer Analysis Results ....................................................................... 3.6.1-1 3.6.1.1 Seven 55-Gallon Drum Payload with 100 ºF Ambient and Full Solar Loading, Uniformly Distributed Decay Heat Load (Case 1) ..... 3.6.1-1 3.6.1.2 Seven 55-Gallon Drum Payload with 100 ºF Ambient and Full Solar Loading, All Decay Heat Load in Center Drum Only (Case 2) . 3.6.1-2 3.6.1.3 Seven 55-Gallon Drum Payload with 100 ºF Ambient and No Solar Loading, Uniformly Distributed Decay Heat Load (Case 1) ..... 3.6.1-3 3.6.1.4 Seven 55-Gallon Drum Payload with 100 ºF Ambient and No Solar Loading, All Decay Heat Load in Center Drum Only (Case 2) . 3.6.1-4 iv
 
HalfPACT Safety Analysis Report                                                                    Rev. 9, August 2022 3.6.2  Thermal Model Details .............................................................................. 3.6.2-1 3.6.2.1 Convection Coefficient Calculation ........................................... 3.6.2-1 3.6.2.2 Aluminum Honeycomb Conductivity Calculation ..................... 3.6.2-1 3.6.2.3 Polyethylene Plastic Wrap Transmittance Calculation .............. 3.6.2-3 4.0 CONTAINMENT ............................................................................................................ 4.1-1 4.1 Containment Boundary............................................................................................. 4.1-1 4.1.1 Containment Vessel ...................................................................................... 4.1-1 4.1.1.1 Outer Confinement Assembly (Secondary Confinement)............. 4.1-1 4.1.1.2 Inner Containment Vessel (Primary Containment) ....................... 4.1-1 4.1.2 Containment Penetrations............................................................................. 4.1-1 4.1.3 Seals and Welds............................................................................................ 4.1-2 4.1.3.1 Seals............................................................................................... 4.1-2 4.1.3.2 Welds ............................................................................................. 4.1-2 4.1.4 Closure.......................................................................................................... 4.1-3 4.1.4.1 Outer Confinement Assembly (OCA) Closure ............................. 4.1-3 4.1.4.2 Inner Containment Vessel (ICV) Closure ..................................... 4.1-3 4.2 Containment Requirements for Normal Conditions of Transport ............................ 4.2-1 4.2.1 Containment of Radioactive Material .......................................................... 4.2-1 4.2.2 Pressurization of Containment Vessel .......................................................... 4.2-1 4.2.3 Containment Criterion .................................................................................. 4.2-1 4.3 Containment Requirements for Hypothetical Accident Conditions ......................... 4.3-1 4.3.1 Fission Gas Products .................................................................................... 4.3-1 4.3.2 Containment of Radioactive Material .......................................................... 4.3-1 4.3.3 Containment Criterion .................................................................................. 4.3-1 4.4 Special Requirements ............................................................................................... 4.4-1 4.4.1 Plutonium Shipments ................................................................................... 4.4-1 4.4.2 Interchangeability ......................................................................................... 4.4-1 5.0 SHIELDING EVALUATION ........................................................................................... 5-1
 
==6.0 CRITICALITY EVALUATION==
.................................................................................... 6.1-1 6.1 Discussion and Results ............................................................................................. 6.1-2 6.2 Package Contents ..................................................................................................... 6.2-1 6.2.1 Applicability of Case A Limit ...................................................................... 6.2-2 6.2.2 Applicability of Case B Limit ...................................................................... 6.2-3 6.2.3 Applicability of Case C Limit ...................................................................... 6.2-3 6.2.4 Applicability of Case D Limit ...................................................................... 6.2-4 6.2.5 Applicability of Case E Limit ...................................................................... 6.2-5 6.2.6 Applicability of Case F Limit ....................................................................... 6.2-5 v
 
HalfPACT Safety Analysis Report                                                                    Rev. 9, August 2022 6.2.7  Applicability of Case G Limit ...................................................................... 6.2-5 6.2.8  Applicability of Case H Limit ...................................................................... 6.2-5 6.2.9  Applicability of Case I Limit........................................................................ 6.2-6 6.3 Model Specification ................................................................................................. 6.3-1 6.3.1 Contents Model ............................................................................................ 6.3-1 6.3.1.1 Case A Contents Model ................................................................. 6.3-1 6.3.1.2 Case B Contents Model ................................................................. 6.3-2 6.3.1.3 Case C Contents Model ................................................................. 6.3-2 6.3.1.4 Case D Contents Model ................................................................. 6.3-2 6.3.2 Packaging Model .......................................................................................... 6.3-3 6.3.3 Single-Unit Models ...................................................................................... 6.3-4 6.3.4 Array Models ................................................................................................ 6.3-5 6.3.5 Package Regional Densities ......................................................................... 6.3-5 6.4 Criticality Calculations ............................................................................................. 6.4-1 6.4.1 Calculational or Experimental Method ........................................................ 6.4-1 6.4.2 Fuel Loading or Other Contents Loading Optimization .............................. 6.4-1 6.4.3 Criticality Results ......................................................................................... 6.4-2 6.4.3.1 Criticality Results for a Single HalfPACT Package ...................... 6.4-3 6.4.3.2 Criticality Results for Infinite Arrays of HalfPACT Packages ..... 6.4-4 6.4.3.3 Special Reflectors in CH-TRU Waste ........................................... 6.4-7 6.4.3.4 Machine Compacted CH-TRU Waste ........................................... 6.4-8 6.4.3.5 Applicable Criticality Limits for CH-TRU Waste ........................ 6.4-9 6.5 Critical Benchmark Experiments ............................................................................. 6.5-1 6.5.1 Benchmark Experiments and Applicability ................................................. 6.5-1 6.5.2 Details of Benchmark Calculations .............................................................. 6.5-2 6.5.3 Results of Benchmark Calculations ............................................................. 6.5-2 7.0 OPERATING PROCEDURES ...................................................................................... 7.1-1 7.1 Procedures for Loading the Package ........................................................................ 7.1-1 7.1.1 Removal of the HalfPACT Package from the Transport Trailer/Railcar ..... 7.1-1 7.1.2 Outer Confinement Assembly (OCA) Lid Removal .................................... 7.1-1 7.1.3 Inner Containment Vessel (ICV) Lid Removal ............................................ 7.1-2 7.1.4 Loading the Payload into the HalfPACT Package ....................................... 7.1-2 7.1.5 Inner Containment Vessel (ICV) Lid Installation ........................................ 7.1-3 7.1.6 Outer Confinement Assembly (OCA) Lid Installation ................................ 7.1-4 7.1.7 Final Package Preparations for Transport (Loaded)..................................... 7.1-6 7.2 Procedures for Unloading the Package .................................................................... 7.2-1 7.2.1 Removal of the HalfPACT Package from the Transport Trailer/Railcar ..... 7.2-1 7.2.2 Outer Confinement Assembly (OCA) Lid Removal .................................... 7.2-1 vi
 
HalfPACT Safety Analysis Report                                                                      Rev. 9, August 2022 7.2.3  Inner Containment Vessel (ICV) Lid Removal ............................................ 7.2-2 7.2.4  Unloading the Payload from the HalfPACT Package .................................. 7.2-2 7.2.5  Inner Containment Vessel (ICV) Lid Installation ........................................ 7.2-2 7.2.6  Outer Confinement Assembly (OCA) Lid Installation ................................ 7.2-3 7.2.7  Final Package Preparations for Transport (Unloaded) ................................. 7.2-4 7.3 Preparation of an Empty Package for Transport ...................................................... 7.3-1 7.4 Preshipment Leakage Rate Test ............................................................................... 7.4-1 7.4.1 Gas Pressure Rise Leakage Rate Test Acceptance Criteria.......................... 7.4-1 7.4.2 Determining the Test Volume and Test Time .............................................. 7.4-1 7.4.3 Performing the Gas Pressure Rise Leakage Rate Test ................................. 7.4-2 7.4.4 Optional Preshipment Leakage Rate Test .................................................... 7.4-2 8.0 ACCEPTANCE TESTS AND MAINTENANCE PROGRAM .................................. 8.1-1 8.1 Acceptance Tests ...................................................................................................... 8.1-1 8.1.1 Visual Inspection .......................................................................................... 8.1-1 8.1.2 Structural and Pressure Tests ....................................................................... 8.1-1 8.1.2.1 Lifting Device Load Testing ......................................................... 8.1-1 8.1.2.2 Pressure Testing ............................................................................ 8.1-2 8.1.3 Fabrication Leakage Rate Tests ................................................................... 8.1-2 8.1.3.1 Fabrication Leakage Rate Test Acceptance Criteria ..................... 8.1-3 8.1.3.2 Helium Leakage Rate Testing the ICV Structure Integrity ........... 8.1-3 8.1.3.3 Helium Leakage Rate Testing the ICV Main O-ring Seal ............ 8.1-3 8.1.3.4 Helium Leakage Rate Testing the ICV Outer Vent Port Plug O-ring Seal .................................................................................... 8.1-4 8.1.3.5 Optional Helium Leakage Rate Testing the OCV Structure Integrity
                        ....................................................................................................... 8.1-4 8.1.3.6 Optional Helium Leakage Rate Testing the OCV Main O-ring Seal Integrity ......................................................................................... 8.1-5 8.1.3.7 Optional Helium Leakage Rate Testing the OCV Vent Port Plug O-ring Seal Integrity ...................................................................... 8.1-6 8.1.4 Component Tests .......................................................................................... 8.1-6 8.1.4.1 Polyurethane Foam ........................................................................ 8.1-6 8.1.5 Tests for Shielding Integrity ....................................................................... 8.1-18 8.1.6 Thermal Acceptance Test ........................................................................... 8.1-23 8.2 Maintenance Program............................................................................................... 8.2-1 8.2.1 Structural and Pressure Tests ....................................................................... 8.2-1 8.2.1.1 Pressure Testing ............................................................................ 8.2-1 8.2.1.2 ICV Interior Surfaces Inspection ................................................... 8.2-1 8.2.2 Maintenance/Periodic Leakage Rate Tests................................................... 8.2-1 8.2.2.1 Maintenance/Periodic Leakage Rate Test Acceptance Criteria .... 8.2-2 8.2.2.2 Helium Leakage Rate Testing the ICV Main O-ring Seal ............ 8.2-2 vii
 
HalfPACT Safety Analysis Report                                                                          Rev. 9, August 2022 8.2.2.3 Helium Leakage Rate Testing the ICV Outer Vent Port Plug O-ring Seal .................................................................................... 8.2-3 8.2.3  Subsystems Maintenance ............................................................................. 8.2-3 8.2.3.1 Fasteners ........................................................................................ 8.2-3 8.2.3.2 Locking Rings ............................................................................... 8.2-3 8.2.3.3 Seal Areas and Grooves ................................................................ 8.2-4 8.2.4  Valves, Rupture Discs, and Gaskets ............................................................. 8.2-6 8.2.4.1 Valves ............................................................................................ 8.2-6 8.2.4.2 Rupture Discs ................................................................................ 8.2-6 8.2.4.3 Gaskets .......................................................................................... 8.2-6 8.2.5  Shielding....................................................................................................... 8.2-7 8.2.6  Thermal ........................................................................................................ 8.2-7 9.0 QUALITY ASSURANCE ............................................................................................... 9.1-1 9.1  Introduction .............................................................................................................. 9.1-1 9.2  Quality Assurance Requirements ............................................................................. 9.2-1 9.2.1 U.S. Nuclear Regulatory Commission ......................................................... 9.2-1 9.2.2 U.S. Department of Energy .......................................................................... 9.2-1 9.2.3 Transportation to or from WIPP ................................................................... 9.2-1 9.3  Quality Assurance Program...................................................................................... 9.3-1 9.3.1 NRC Regulatory Guide 7.10 ........................................................................ 9.3-1 9.3.2 Design ........................................................................................................... 9.3-1 9.3.3 Fabrication, Assembly, Testing, and Modification ...................................... 9.3-1 9.3.4 Use ................................................................................................................ 9.3-1 9.3.4.1 DOE Shipments: To/From WIPP ................................................. 9.3-1 9.3.4.2 Other DOE Shipments: Non-WIPP .............................................. 9.3-1 9.3.4.3 Non-DOE Users of HalfPACT ...................................................... 9.3-2 9.3.5 Maintenance and Repair ............................................................................... 9.3-2 LIST OF TABLES Table 2.1 Containment Structure Allowable Stress Limits ................................................ 2.1-7 Table 2.1 Non-Containment Structure Allowable Stress Limits ........................................ 2.1-7 Table 2.2 HalfPACT Weight and Center of Gravity .......................................................... 2.2-7 Table 2.3 Mechanical Properties of Type 304 Stainless Steel Components (for Analysis)2.3-5 Table 2.3 Mechanical Properties of Polyurethane Foam (for Analysis) .............................. 2.3-7 Table 2.3 Mechanical Properties of Metallic Materials (for Testing) ................................ 2.3-7 Table 2.6 Summary of Stress Results for OCA Load Case 1 ........................................... 2.6-14 Table 2.6 Summary of Stress Results for OCA Load Case 2 ........................................... 2.6-15 viii
 
HalfPACT Safety Analysis Report                                                                              Rev. 9, August 2022 Table 2.6 Summary of Stress Results for OCA Load Case 3 ........................................... 2.6-16 Table 2.6 Summary of Stress Results for OCA Load Case 4 ........................................... 2.6-17 Table 2.6 Summary of Stress Results for ICV Load Case 1 ............................................ 2.6-18 Table 2.6 Summary of Stress Results for ICV Load Case 2 ............................................ 2.6-19 Table 2.6 Buckling Geometry Parameters per Code Case N-284-1 ................................. 2.6-20 Table 2.6 Stress Results for 14.7 psig External Pressure ................................................. 2.6-20 Table 2.6 Buckling Summary for 14.7 psig External Pressure ........................................ 2.6-21 Table 2.6 Tie-down Lug Weld Shear Stresses ............................................................... 2.6-22 Table 2.6 OCA Outer Shell Compressive Membrane Stresses ............................................ 2.6-22 Table 2.6 OCA Tie-down Weldment Compressive Membrane Stresses ......................... 2.6-22 Table 2.6 Maximum Unit Alternating Stress Intensities ................................................ 2.6-22 Table 2.7 Summary of HalfPACT Engineering Test Unit (ETU) Tests and Results ....... 2.7-11 Table 2.7 Summary of Selected Certification Test Unit (CTU) Tests ............................. 2.7-12 Table 2.7 Buckling Geometry Parameters per Code Case N-284-1 ................................. 2.7-13 Table 2.7 Stress Results for 21 psig External Pressure .................................................... 2.7-13 Table 2.7 Buckling Summary for 21 psig External Pressure ........................................... 2.7-14 Table 2.10.1 ANSYS Input Listing for OCA Load Case 1 ......................................... 2.10.1-7 Table 2.10.1 ANSYS Input Listing for OCA Load Case 2 ....................................... 2.10.1-12 Table 2.10.1 ANSYS Input Listing for OCA Load Case 3 ....................................... 2.10.1-17 Table 2.10.1 ANSYS Input Listing for OCA Load Case 4 ....................................... 2.10.1-22 Table 2.10.1 ANSYS Input Listing for ICV Load Case 1 ......................................... 2.10.1-27 Table 2.10.1 ANSYS Input Listing for ICV Load Case 2 ......................................... 2.10.1-30 Table 2.10.2 Formulation Qualification Test O-ring Seal Compression Parameters .... 2.10.2-6 Table 2.10.2 Rainier Rubber R0405-70 Formulation Qualification O-ring Seal Test Results ................................................................................................................ 2.10.2-11 Table 2.10.3 TRUPACT-II / HalfPACT Comparison Using NUREG/CR-3966 ........ 2.10.3-43 Table 2.10.3 Summary of HalfPACT ETU Test Results in Sequential Order .......... 2.10.3-44 Table 2.10.3 Summary of HalfPACT CTU Test Results in Sequential Order .......... 2.10.3-45 Table 2.10.3 Summary of HalfPACT CTU Temperature Indicating Label Readings 2.10.3-46 Table 3.1 NCT Steady-State Temperatures with 30 Watts Decay Heat Load and Insolation; Seven, 55-Gallon Drums................................................................................. 3.1-5 Table 3.2 Thermal Properties of Homogenous Materials................................................... 3.2-2 Table 3.2 Thermal Properties of Non-Homogenous Materials .......................................... 3.2-3 ix
 
HalfPACT Safety Analysis Report                                                                              Rev. 9, August 2022 Table 3.2 Thermal Properties of Air ................................................................................... 3.2-4 Table 3.2 Thermal Radiative Properties ............................................................................. 3.2-5 Table 3.4 NCT Steady-State Temperatures with 30 Watts Decay Heat Load and Insolation; Seven 55-Gallon Drums................................................................................ 3.4-12 Table 3.4 Summary of Temperatures for Determining MNOP for the ICV ...................... 3.4-13 Table 3.4 HalfPACT Pressure Increase with a 7-Drum Payload, 60-Day Duration* ...... 3.4-15 Table 3.4 HalfPACT Pressure Increase with a 1 SWB Payload, 60-Day Duration* .............. 3.4-15 Table 3.4 HalfPACT Pressure Increase with 4 Drums Overpacked in 1 SWB, 60-Day Duration* ......................................................................................................................... 3.4-15 Table 3.4 HalfPACT Pressure Increase with 4 85-Gallon Drums or 4 55-Gallon Drums Overpacked in 4 85-Gallon Drums, 60-Day Duration*....................................................... 3.4-16 Table 3.4 HalfPACT Pressure Increase with 3 100-Gallon Drums, 60-Day Duration* ......... 3.4-16 Table 3.4 HalfPACT Pressure Increase with 3 SC-30G1 Shielded Containers, 60-Day Duration* ......................................................................................................................... 3.4-16 Table 3.4 HalfPACT Pressure Increase with 7 CCOs, 60-Day Duration*............................. 3.4-17 Table 3.4 HalfPACT Pressure Increase with 2 SC-30G2 Shielded Containers, 60-Day Duration* ........................................................................................................................ 3.4-17 Table 3.4 HalfPACT Pressure Increase with 1 SC-30G3 Shielded Container, 60-Day Duration* ........................................................................................................................ 3.4-17 Table 3.4 HalfPACT Pressure Increase with 2 SC-55G1 Shielded Containers, 60-Day Duration* ........................................................................................................................ 3.4-18 Table 3.4 HalfPACT Pressure Increase with 1 SC-55G2 Shielded Container, 60-Day Duration* ........................................................................................................................ 3.4-18 Table 3.5 NCT Steady-State Temperatures with 30 Watts Decay Heat Load and Zero Insolation; Seven 55-Gallon Drums.................................................................................. 3.5-5 Table 3.5 HAC Thermal Event Temperature Readings ..................................................... 3.5-6 Table 3.6.2 Effective Thermal Conductivity of Aluminum Honeycomb ........................ 3.6.2-2 Table 6.1 Fissile Material Limit per Payload Container .................................................... 6.1-4 Table 6.1 Fissile Material Limit per HalfPACT Package .................................................. 6.1-4 Table 6.1 Summary of Criticality Analysis Results ........................................................... 6.1-5 Table 6.2 Special Reflector Material Parameters that Achieve the Reactivity of a 25%/75%
Polyethylene/Water Mixture Reflector ............................................................................. 6.2-6 Table 6.3 Description of Contents Displacement in Array Models ................................... 6.3-6 Table 6.3 Fissile Contents Model Properties for Various H/Pu Ratios .............................. 6.3-7 Table 6.3 Composition of Modeled Steels ......................................................................... 6.3-8 Table 6.3 Composition of the Polyethylene/Water/Beryllium Reflector ........................... 6.3-8 x
 
HalfPACT Safety Analysis Report                                                                                Rev. 9, August 2022 Table 6.4 Single-Unit, NCT, Case A, 325 FGE; ks vs. H/Pu Ratio with Different Moderator and Reflector Compositions ............................................................................................ 6.4-11 Table 6.4 Single Unit, NCT, Case A, 325 FGE; Variation of Reflector Volume Fraction (VF) at Near-Optimal H/Pu Ratio............................................................................................ 6.4-12 Table 6.4 Single-Unit, HAC, Case A, 325 FGE; ks vs. H/Pu at Maximum Reflection Conditions ....................................................................................................................... 6.4-12 Table 6.4 Infinite Array Variation 0, HAC, Case A, 325 FGE; ks vs. H/Pu at Extremes of Reflection Conditions ..................................................................................................... 6.4-13 Table 6.4 Infinite Array Variation 0, HAC, Case A, 325 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratios .............................................................. 6.4-14 Table 6.4 Infinite Array Variation 1, HAC, Case A, 325 FGE; Variation of H/Pu Ratio at Extremes of Reflection Conditions ................................................................................. 6.4-15 Table 6.4 Infinite Array Variation 0, HAC, Case A; Variation of H/Pu Ratio for Various Gram Quantities of Pu-240 at Maximum Reflection Conditions ................................... 6.4-16 Table 6.4 Infinite Array Variation 0, HAC, Case A, 5 g Pu-240, 340 FGE; ks vs. H/Pu for Various Combinations of U-235 and Pu-239 under Maximum Reflection Conditions.. 6.4-17 Table 6.4 Infinite Array Variation 0, HAC, Case B, 100 FGE; ks vs. H/Pu at Maximum Reflection Conditions ..................................................................................................... 6.4-18 Table 6.4 Infinite Array Variation 0, HAC, Case B, 100 FGE; ks vs. H/Pu for Various Moderator Volume Fractions of Beryllium under Maximum Reflection Conditions .... 6.4-19 Table 6.4 Infinite Array Variation 0, HAC, Case B, 100 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratio ............................................................... 6.4-20 Table 6.4 Infinite Array Variation 1, HAC, Case B, 100 FGE; Variation of H/Pu Ratio at Reflector Volume Fraction to Maximize Interaction while Maintaining Beryllium Reflection ........................................................................................................................ 6.4-20 Table 6.4 Infinite Array Variation 0, HAC, Case C, 250 FGE; ks vs. H/Pu at Maximum Reflection Conditions ..................................................................................................... 6.4-21 Table 6.4 Infinite Array Variation 0, HAC, Case C, 250 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratio ............................................................... 6.4-21 Table 6.4 Infinite Array Variation 1, HAC, Case C, 250 FGE; Variation of H/Pu Ratio at Reflector Volume Fraction to Maximize Interaction while Maintaining Reflection ...... 6.4-22 Table 6.4 Infinite Array Variation 0, HAC, Case D, 325 FGE; ks vs. H/Pu at Maximum Reflection Conditions ..................................................................................................... 6.4-23 Table 6.4 Infinite Array Variation 0, HAC, Case D, 325 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratio ............................................................... 6.4-24 Table 6.4 Infinite Array Variation 1, HAC, Case D, 325 FGE; Variation of H/Pu Ratio at Reflector Volume Fraction to Maximize Interaction while Maintaining Reflection ...... 6.4-24 Table 6.5 Benchmark Experiment Description with Experimental Uncertainties ............................. 6.5-4 xi
 
HalfPACT Safety Analysis Report                                                                    Rev. 9, August 2022 Table 6.5 Benchmark Case Parameters and Computed Results ............................................... 6.5-5 Table 6.5 Calculation of USL ........................................................................................... 6.5-13 Table 8.1 Acceptable Compressive Stress Ranges for Foam (psi) ................................... 8.1-18 LIST OF FIGURES Figure 1.1 HalfPACT Package Assembly .......................................................................... 1.1-3 Figure 1.1 HalfPACT Packaging Closure/Seal Region Details ......................................... 1.1-4 Figure 1.2 ICV Closure Design (OCV closure is similar).................................................. 1.2-9 Figure 2.2 HalfPACT Package Components ...................................................................... 2.2-9 Figure 2.2 Radial Shift of CG for Seven 55-Gallon Drum Payload ................................. 2.2-10 Figure 2.2 Radial Shift of CG for One SWB Payload ...................................................... 2.2-11 Figure 2.2 Radial Shift of CG for Four 85-Gallon Drum Payload ................................... 2.2-12 Figure 2.2 Radial Shift of CG for Three 100-Gallon Drum Payload ............................... 2.2-13 Figure 2.2 Radial Shift of CG for Three SC-30G1 Shielded Container Payload ............. 2.2-14 Figure 2.2 Radial Shift of CG for Two SC-30G2 Shielded Container Payload ............... 2.2-15 Figure 2.2 Radial Shift of CG for One SC-30G3 Shielded Container Payload................ 2.2-16 Figure 2.2 Radial Shift of CG for Two SC-55G1 Shielded Container Payload ............... 2.2-17 Figure 2.2 Radial Shift of CG for One SC-55G2 Shielded Container Payload.............. 2.2-18 Figure 2.5 Tie-down Device Layout................................................................................. 2.5-12 Figure 2.5 Tie-down Device Detail .................................................................................. 2.5-13 Figure 2.5 Tie-down Plan View and Reaction Force Diagram ........................................ 2.5-14 Figure 2.5 Tie-down Tensile/Shear Failure Modes .......................................................... 2.5-15 Figure 2.5 Tie-down Lug Dimensions and Load Diagram ............................................... 2.5-16 Figure 2.5 Horizontal Doubler and Tripler Plate Details ................................................. 2.5-17 Figure 2.6 OCA Load Case 1, Overall Model .................................................................. 2.6-23 Figure 2.6 OCA Load Case 1, Seal Region Detail ........................................................... 2.6-24 Figure 2.6 OCA Load Case 2, Overall Model .................................................................. 2.6-25 Figure 2.6 OCA Load Case 2, Seal Region Detail ........................................................... 2.6-26 Figure 2.6 OCA Load Case 3, Overall Model .................................................................. 2.6-27 Figure 2.6 OCA Load Case 3, Seal Region Detail ........................................................... 2.6-28 Figure 2.6 OCA Load Case 4, Overall Model .................................................................. 2.6-29 Figure 2.6 OCA Load Case 4, Seal Region Detail ........................................................... 2.6-30 Figure 2.6 ICV Load Case 1, Overall Model ................................................................... 2.6-31 xii
 
HalfPACT Safety Analysis Report                                                                                Rev. 9, August 2022 Figure 2.6 ICV Load Case 1, Seal Region Detail ........................................................... 2.6-32 Figure 2.6 ICV Load Case 2, Overall Model ................................................................. 2.6-33 Figure 2.6 ICV Load Case 2, Seal Region Detail ........................................................... 2.6-34 Figure 2.10.1 OCA FEA Model Element Plot............................................................. 2.10.1-33 Figure 2.10.1 ICV FEA Model Element Plot .............................................................. 2.10.1-34 Figure 2.10.2 Configuration for Minimum ICV O-ring Seal Compression ................ 2.10.2-13 Figure 2.10.2 Test Fixture for O-ring Seal Performance Testing ................................ 2.10.2-14 Figure 2.10.3 Drop Pad at the Coyote Canyon Aerial Cable Facility ......................... 2.10.3-47 Figure 2.10.3 Design Comparison between a TRUPACT-II Packaging and a HalfPACT Packaging ................................................................................................................... 2.10.3-49 Figure 2.10.3 Design Comparison between 55-Gallon Drum Payload Assemblies .... 2.10.3-50 Figure 2.10.3 Making the HalfPACT ETU OCA from TRUPACT-II Unit 104 ................. 2.10.3-51 Figure 2.10.3 Making the HalfPACT ETU OCA from TRUPACT-II Unit 104 ................. 2.10.3-52 Figure 2.10.3 Making the HalfPACT CTU OCA from TRUPACT-II Unit 107 ................. 2.10.3-53 Figure 2.10.3 Making the HalfPACT CTU ICV from TRUPACT-II Unit 107................... 2.10.3-54 Figure 2.10.3 Dimensional Comparison of TRUPACT-II and HalfPACT for NUREG/CR-3966 (Lower Figures are Simplifying Representations Used in CASKDROP) ......... 2.10.3-55 Figure 2.10.3 Schematic of HalfPACT ETU Test Orientations .................................. 2.10.3-56 Figure 2.10.3 Schematic of HalfPACT CTU Test Orientations ................................ 2.10.3-57 Figure 2.10.3 Schematic of HalfPACT CTU Temperature Indicating Label Location ..................................................................................................................... 2.10.3-59 Figure 2.10.3 ETU Free Drop Test 1; Top-End Damage; ~16" Wide Flat ............... 2.10.3-61 Figure 2.10.3 ETU Free Drop Test 1; Bottom-End Damage; ~18" Wide Flat .......... 2.10.3-61 Figure 2.10.3 ETU Free Drop Test 2; Top-End Damage; ~36" Wide Flat ............... 2.10.3-62 Figure 2.10.3 ETU Free Drop Test 2; Bottom-End Damage; ~33" Wide Flat .......... 2.10.3-62 Figure 2.10.3 ETU Free Drop Test 3; View Just Prior to NCT Free Drop Test ....... 2.10.3-63 Figure 2.10.3 ETU Free Drop Test 3; Top-End Damage; ~18" Wide Flat ............... 2.10.3-63 Figure 2.10.3 ETU Free Drop Test 4; Top-End Damage; ~34" Wide Flat ............... 2.10.3-64 Figure 2.10.3 ETU Free Drop Test 4; Bottom-End Damage; ~34" Wide Flat .......... 2.10.3-64 Figure 2.10.3 ETU Free Drop Test 5; Bottom Corner Damage; ~26" Wide Flat ..... 2.10.3-65 Figure 2.10.3 ETU Free Drop Test 5; Bottom Corner Damage; ~51/2" Deep Flat ..... 2.10.3-65 Figure 2.10.3 ETU Free Drop Test 6; Bottom Corner Damage; ~40" Wide Flat ..... 2.10.3-66 Figure 2.10.3 ETU Free Drop Test 6; Bottom Corner Damage; ~12" Deep Flat ...... 2.10.3-66 xiii
 
HalfPACT Safety Analysis Report                                                                                  Rev. 9, August 2022 Figure 2.10.3 ETU Puncture Drop Test 7; ~101/2" High x ~111/2" Wide Hole .......... 2.10.3-67 Figure 2.10.3 ETU Puncture Drop Test 7; Radial Penetration ~8" Deep .................. 2.10.3-67 Figure 2.10.3 ETU Puncture Drop Test 8; View of Damage; ~21/2" Deep Dent ....... 2.10.3-68 Figure 2.10.3 ETU Puncture Drop Test 8; Close-up View of Damage; ~21/2" Deep Dent ............................................................................................................................ 2.10.3-68 Figure 2.10.3 ETU Puncture Drop Test 9; View of Impact on Puncture Bar ........... 2.10.3-69 Figure 2.10.3 ETU Puncture Drop Test 9; Bottom Corner Damage; ~3" Deep Dent ............................................................................................................................ 2.10.3-69 Figure 2.10.3 ETU Puncture Drop Test 10; 3/8-to-1/4 Transition; ~27" Long Tear ............................................................................................................................ 2.10.3-70 Figure 2.10.3 ETU Puncture Drop Test 10; 3/8-to-1/4 Transition; ~51/2" Deep Dent ............................................................................................................................ 2.10.3-70 Figure 2.10.3 ETU Fire Test 11; Side 1 View Showing Tests 1, 2, 7, & 10 Damage ...................................................................................................................... 2.10.3-71 Figure 2.10.3 ETU Fire Test 11; Side 2 View Showing Tests 3, 4, 5, 6, 8, & 9 Damage ...................................................................................................................... 2.10.3-71 Figure 2.10.3 ETU Fire Test 11; Overall View ~5 Minutes after Start of Fire ......... 2.10.3-72 Figure 2.10.3 ETU Fire Test 11; View ~12 Minutes after Start of Fire .................... 2.10.3-73 Figure 2.10.3 ETU Fire Test 11; View ~25 Minutes after Start of Fire .................... 2.10.3-73 Figure 2.10.3 ETU Fire Test 11; View ~32 Minutes after Start of Fire .................... 2.10.3-74 Figure 2.10.3 ETU Fire Test 11; View ~17 Minutes after End of Fire ..................... 2.10.3-74 Figure 2.10.3 ETU Fire Test 11; View ~37 Minutes after End of Fire ..................... 2.10.3-75 Figure 2.10.3 ETU; View Before Disassembly ......................................................... 2.10.3-75 Figure 2.10.3 ETU; Removal of the OCA Lid Outer Shell (Note Crumbling Foam Char) .......................................................................................................................... 2.10.3-76 Figure 2.10.3 ETU; Residual Foam in OCA Lid Side; Aligned with Test 1, 2, & 7 Damage....................................................................................................................... 2.10.3-76 Figure 2.10.3 ETU; Residual Foam in OCA Lid Side; Remote From Test Damage 2.10.3-77 Figure 2.10.3 ETU; Residual Foam in OCA Lid Top (~11") .................................... 2.10.3-77 Figure 2.10.3 ETU; View of OCV Seal Test Port Plug (As Removed; Not Cleaned) ..................................................................................................................... 2.10.3-78 Figure 2.10.3 ETU; View of OCV Vent Port Cover (As Removed; Not Cleaned)... 2.10.3-78 Figure 2.10.3 ETU; View of OCV Vent Port Plug (As Removed; Not Cleaned) ..... 2.10.3-79 Figure 2.10.3 ETU; View of 55-Gallon Payload Drums Following ICV Lid Removal ..................................................................................................................... 2.10.3-79 xiv
 
HalfPACT Safety Analysis Report                                                                                  Rev. 9, August 2022 Figure 2.10.3 ETU; View of ICV Body Cavity Following Payload Drum Removal ..................................................................................................................... 2.10.3-80 Figure 2.10.3 ETU; View of Debris Inside ICV Body Cavity After Payload Drum Removal...................................................................................................................... 2.10.3-80 Figure 2.10.3 CTU; 5-Inch Thick Payload Spacer (Wood Simulation) in Bottom of ICV ........................................................................................................................ 2.10.3-81 Figure 2.10.3 CTU; Aligning 55-Gallon Drum Payload Assembly for Installation into ICV ...................................................................................................................... 2.10.3-81 Figure 2.10.3 CTU; Final ICV Lid Alignment During ICV Lid Installation ............ 2.10.3-82 Figure 2.10.3 CTU; Final OCA Lid Alignment During OCA Lid Installation ......... 2.10.3-82 Figure 2.10.3 CTU; Certification Test Unit (TRUPACT-II Unit 107) After Final Assembly .................................................................................................................... 2.10.3-83 Figure 2.10.3 CTU Free Drop Test 1; Lid-End Damage; ~13" Wide Flat ................ 2.10.3-84 Figure 2.10.3 CTU Free Drop Test 1; Bottom-End Damage; ~13" Wide Flat.......... 2.10.3-85 Figure 2.10.3 CTU Free Drop Test 2; Lid-End Damage; ~37 Wide Flat ................ 2.10.3-86 Figure 2.10.3 CTU Free Drop Test 2; Bottom-End Damage; ~37" Wide Flat.......... 2.10.3-87 Figure 2.10.3 CTU Free Drop Test 3; Lid-End Damage; ~411/2" Wide Flat ............. 2.10.3-88 Figure 2.10.3 CTU Free Drop Test 3; Bottom-End Damage .................................... 2.10.3-89 Figure 2.10.3 CTU Puncture Drop Test 4; Mounting the Puncture Bar .................... 2.10.3-90 Figure 2.10.3 CTU Puncture Drop Test 4; Close-up View of Damage..................... 2.10.3-91 Figure 2.10.3 CTU Puncture Drop Test 4; Close-up Profile View of Damage;
    ~33/4" Deep.................................................................................................................. 2.10.3-92 Figure 2.10.3 CTU Puncture Drop Test 5; Close-up View of Damage..................... 2.10.3-93 Figure 2.10.3 CTU Puncture Drop Test 5; Profile Views of Damage; ~4" Deep ..... 2.10.3-94 Figure 2.10.3 CTU Puncture Drop Test 6; Overall View of Damage ....................... 2.10.3-95 Figure 2.10.3 CTU Puncture Drop Test 6; Close-up Views of Damage; ~31/2" Deep ........................................................................................................................... 2.10.3-96 Figure 2.10.3 CTU Fire Test 7; Side 1 View Before Fire Showing Tests 1, 2, & 4 Damage ....................................................................................................................... 2.10.3-97 Figure 2.10.3 CTU Fire Test 7; Side 2 View Before Fire Showing Test 5 Damage ...................................................................................................................... 2.10.3-98 Figure 2.10.3 CTU Fire Test 7; Overall View ~5 Minutes after Start....................... 2.10.3-99 Figure 2.10.3 CTU Fire Test 7; View ~10 Minutes after Start ............................... 2.10.3-100 Figure 2.10.3 CTU Fire Test 7; View ~15 Minutes after Start (Showing Wind Effects) ..................................................................................................................... 2.10.3-101 xv
 
HalfPACT Safety Analysis Report                                                                                    Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; View ~28 Minutes after Start (Note Flares at Vents) ....................................................................................................................... 2.10.3-102 Figure 2.10.3 CTU Fire Test 7; Side 1 View ~33 Minutes after Start (End of Fire) .......................................................................................................................... 2.10.3-103 Figure 2.10.3 CTU Fire Test 7; Side 2 View ~33 Minutes after Start (End of Fire) .......................................................................................................................... 2.10.3-104 Figure 2.10.3 CTU Fire Test 7; Side 1/2 Views ~10 Minutes after End of Fire ..... 2.10.3-105 Figure 2.10.3 CTU; View Before Disassembly (OCV Seal Test Port in Foreground).............................................................................................................. 2.10.3-106 Figure 2.10.3 CTU; Removal of the OCA Lid Outer Shell (Note Crumbling Foam Char) ........................................................................................................................ 2.10.3-107 Figure 2.10.3 CTU; Residual Foam in OCA Lid Side; Aligned with Test 1, 2, & 4 Damage..................................................................................................................... 2.10.3-108 Figure 2.10.3 CTU; Residual Foam in OCA Lid Knuckle; Aligned with Test 1, 2, & 4 Damage ..................................................................................................................... 2.10.3-108 Figure 2.10.3 CTU; Residual Foam in OCA Lid Top (~11") ................................. 2.10.3-109 Figure 2.10.3 CTU; Residual Foam in OCA Lid Side; Remote from Test Damage .................................................................................................................... 2.10.3-109 Figure 2.10.3 CTU; Close-up of OCV Seal Test Port Plug (As Removed/Not Cleaned) ................................................................................................................... 2.10.3-110 Figure 2.10.3 CTU; OCV Vent Port Region After Removing Excess Foam Char . 2.10.3-110 Figure 2.10.3 CTU; Close-up of OCV Vent Port Cover (As Removed/Not Cleaned) ................................................................................................................... 2.10.3-111 Figure 2.10.3 CTU; Close-up of OCV Vent Port Plug (As Removed/Not Cleaned) ................................................................................................................... 2.10.3-111 Figure 2.10.3 CTU; Close-up of Damage to ICV Locking Ring ............................ 2.10.3-112 Figure 2.10.3 CTU; End View of OCV Cavity Showing Deformed Lower Seal Flange ....................................................................................................................... 2.10.3-112 Figure 2.10.3 CTU; Residual Foam in OCA Lid Side; Aligned with Test 1, 2, & 4 Damage..................................................................................................................... 2.10.3-113 Figure 2.10.3 CTU; Residual Foam in OCA Body Side; Remote from Test Damage .................................................................................................................... 2.10.3-113 Figure 2.10.3 CTU; Helium Leakage Rate Testing the ICV Lid Structure ............. 2.10.3-114 Figure 2.10.3 CTU; Helium Leakage Rate Testing the OCV Body Structure ........ 2.10.3-114 Figure 2.10.3 CTU; Close-up View of Cracked OCV Vent Port Coupling Inner Weld ......................................................................................................................... 2.10.3-115 xvi
 
HalfPACT Safety Analysis Report                                                                                  Rev. 9, August 2022 Figure 2.10.3 CTU; Close-up View of Cracked OCV Vent Port Coupling Inner Weld ......................................................................................................................... 2.10.3-115 Figure 3.4 HalfPACT Packaging Thermal Model Node Layout ...................................... 3.4-19 Figure 3.4 Seven 55-Gallon Drum Payload Thermal Node Layout ................................. 3.4-20 Figure 3.5 HAC Thermal Event Temperature Indicating Label Locations ............................ 3.5-7 Figure 6.3 Case A Contents Model .................................................................................... 6.3-9 Figure 6.3 Case B Contents Model ................................................................................... 6.3-10 Figure 6.3 Case C Contents Model ................................................................................... 6.3-11 Figure 6.3 Case D Contents Model .................................................................................. 6.3-12 Figure 6.3 NCT, Single-Unit Model; R-Z Slice ............................................................... 6.3-13 Figure 6.3 HAC, Single-Unit Model; R-Z Slice............................................................... 6.3-14 Figure 6.3 Array Model Variation 0 (Reflective Boundary Conditions Imposed) ................... 6.3-15 Figure 6.3 Array Model Variation 1; X-Y Slice Through Top Axial Layer .................... 6.3-16 Figure 7.4 Pressure Rise Leakage Rate Test Schematic ..................................................... 7.4-2 Figure 8.1 SC-30G2 Gamma Scan Grid Layout Beyond the Payload Cavity.................. 8.1-20 Figure 8.1 SC-30G3 Gamma Scan Grid Layout Beyond the Payload Cavity.................. 8.1-21 Figure 8.1 SC-55G2 Gamma Scan Grid Layout Beyond the Payload Cavity.................. 8.1-22 Figure 8.2 Method of Measuring Upper Seal Flange Groove Widths................................ 8.2-8 Figure 8.2 Method of Measuring Lower Seal Flange Groove Widths ............................... 8.2-9 Figure 8.2 Method of Measuring Upper Seal Flange Tab Widths ................................... 8.2-10 Figure 8.2 Method of Measuring Lower Seal Flange Tab Widths ................................... 8.2-11 xvii
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
xviii
 
HalfPACT Safety Analysis Report                                                              Rev. 9, August 2022 1.0 GENERAL INFORMATION This chapter of the Safety Analysis Report (SAR) presents a general introduction and description of the HalfPACT contact-handled transuranic waste (CH-TRU) package. The major components comprising the HalfPACT package are presented as Figure 1.1-1 and Figure 1.1-2. Figure 1.1-1 presents an exploded view of all major HalfPACT packaging components. Figure 1.1-2 presents a detailed view of the closure and seal region. Detailed drawings presenting the HalfPACT packaging design are presented in Appendix 1.3.1, Packaging General Arrangement Drawings.
All details relating to payloads and payload preparation for shipment in a HalfPACT package are presented in the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) 1. Descriptions of the standard, S100, S200, and S300 pipe overpack payload configurations are provided in Appendices 4.1, 4.2, 4.3, and 4.4, respectively, of the CH-TRU Payload Appendices 2. Descriptions of the SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2 shielded container payload configurations are provided in Appendices 4.5, 4.7, 4.8, 4.9, and 4.10 of the CH-TRU Payload Appendices. A description of the criticality control overpack payload configuration is provided in Appendix 4.6 of the CH-TRU Payload Appendices. Terminology and acronyms used throughout this document are presented as Appendix 1.3.2, Glossary of Terms and Acronyms.
1.1 Introduction The model HalfPACT package has been developed for the United States Department of Energy (DOE) as a safe means for transportation of CH-TRU materials and other authorized payloads.
The packaging design is based very closely on the currently licensed TRUPACT-II package. The primary difference between the two packages is the body length. The TRUPACT-II packaging body length is shortened by 30 inches to create the HalfPACT packaging. Other minor differences are present, as described in subsequent sections.
The HalfPACT package is designed for truck transport. As many as three, loaded HalfPACT packages can be transported on a single semi-trailer. The rugged, lightweight design of the HalfPACT package allows the efficient transport of heavier-than-average payloads, thereby reducing the total number of radioactive shipments. The HalfPACT is also suitable for rail transport. As many as seven loaded HalfPACT packages can be transported per railcar.
The goals of maintaining public safety while achieving a lightweight design are satisfied by use of a deformable sealing region that can absorb both normal conditions of transport (NCT) and hypothetical accident condition (HAC) deformations without loss of leaktight capability 3. This same design was extensively tested on the TRUPACT-II package, and the HalfPACT packaging program utilized the knowledge of the TRUPACT-II packaging program as background information.
Nevertheless, both a full scale HalfPACT engineering test unit (ETU), and a certification test unit 1
U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
2 U.S. Department of Energy (DOE), CH-TRU Payload Appendices, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
3 Leaktight is defined as 1 x 10-7 standard cubic centimeters per second (scc/s), or less, air leakage per the definition in ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, (ANSI), Inc.
1.1-1
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 (CTU) were subjected to a series of free drops and puncture drops, and a fully engulfing pool fire test. These tests conclusively demonstrated containment integrity of the HalfPACT package.
The payload within each HalfPACT package will be within 55-gallon drums, 85-gallon drums, 100-gallon drums, standard waste boxes (SWBs), or shielded containers (SCs). Hereafter, the term 85-gallon drum is used to refer to 75- to 88-gallon drums that may, with the appropriate dimensions, overpack a single 55-gallon drum. Pipe overpacks and criticality control overpacks (CCO) utilize 55-gallon drums as overpacks. A single HalfPACT package can transport seven 55-gallon drums (with or without pipe components or criticality control containers), one SWB, four 85-gallon drums (with or without 55-gallon drums), three 100-gallon drums, or up to three SCs. Specifications for payload containers are provided in Section 2.0, Container and Physical Properties Requirements, of CH-TRAMPAC.
The HalfPACT packaging provides a single leakage rate testable level of containment for the payload during both normal conditions of transport (NCT) and hypothetical accident conditions (HAC). However, the HalfPACT package was originally designed, tested, and licensed prior to 2004 with two levels of containment. The 2004 NRC Rule change with regard to 10 CFR
§71.63 4, 5 eliminated the requirement for double containment in packages carrying in excess of 20 curies of plutonium in solid form. With only a single level of containment now required, the outer containment assembly (OCA) has been revised throughout this document to be the outer confinement assembly (still the OCA), and the outer containment vessel (OCV) has been revised throughout this document to be the outer confinement vessel (still the OCV). The use of O-ring seals (and corresponding pressure and leakage rate testing) is now optional for the OCV, and design and fabrication of the OCA (including the OCV) now falls under ASME Boiler and Pressure Vessel Code, Section III, Subsection NF 6. For conservatism, structural calculations for the OCV presented in Chapter 2.0, Structural Evaluation, continue to use the requirements from ASME Boiler and Pressure Vessel Code, Section III, Subsection NB 7.
Based on the shielding and criticality assessments provided in Chapter 5.0, Shielding Evaluation, and Chapter 6.0, Criticality Evaluation, the Criticality Safety Index (CSI) for the HalfPACT package is zero (0.0), and the shielding Transport Index (TI) is determined at the time of shipment.
Authorization is sought for shipment of the HalfPACT package by truck or railcar as a Type B(U)F-96 package per the definition delineated in 10 CFR §71.44.
4 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
5 Compatibility With IAEA Transportation Safety Standards (TS-R-1) and Other Transportation Safety Amendments, Federal Register, 69 FR 3698, effective date October 1, 2004.
6 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, Subsection NF, Supports, 1995 Edition, 1997 Addenda.
7 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, Subsection NB, Class 1 Components, 1995 Edition, 1997 Addenda.
1.1-2
 
HalfPACT Safety Analysis Report          Rev. 9, August 2022 Figure 1.1 HalfPACT Package Assembly 1.1-3
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 1.1 HalfPACT Packaging Closure/Seal Region Details 1.1-4
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 1.2 Package Description This section presents a basic description of the HalfPACT package. General arrangement drawings of the HalfPACT packaging are presented in Appendix 1.3.1, Packaging General Arrangement Drawings. Drawings illustrating payload assembly details are presented in the CH-TRAMPAC 1.
1.2.1      Packaging 1.2.1.1      Packaging Description The HalfPACT packaging is comprised of an outer confinement assembly (OCA) that provides a secondary confinement boundary when its optional O-ring seals are utilized, and an inner containment vessel (ICV) that provides the primary containment boundary. Two aluminum honeycomb spacer assemblies are used within the ICV, one inside each ICV torispherical head.
A silicone wear pad is utilized at the interface between the bottom exterior of the ICV and the bottom interior of the OCA. An optional polyester foam annulus ring may be used in the annulus between the ICV and OCV, just below the OCV lower seal flange to prevent debris from becoming entrapped between the vessels.
Inside the ICV, the payload will be within 55-gallon drums, 85-gallon drums, 100-gallon drums, standard waste boxes (SWBs), or shielded containers (SCs). The OCA, ICV, and the aluminum honeycomb spacer assemblies are fully described in the following subsections. The design details and overall arrangement of the HalfPACT packaging are presented in the Appendix 1.3.1, Packaging General Arrangement Drawings. Drawings illustrating payload assembly details are presented in the CH-TRAMPAC.
1.2.1.1.1      Outer Confinement Assembly (OCA)
The OCA consists of an OCA lid and OCA body, each primarily comprised of an inner stainless steel shell structure, a relatively thick layer of rigid polyurethane foam, and an external stainless steel shell structure. The inner OCA shell structure comprises the outer confinement vessel (OCV).
Not considering the seal flange region, the OCA lid has a nominal external diameter of 94 inches and a nominal internal diameter of 76 inches. Likewise, not considering the seal flange region, the OCA body has a nominal external diameter of 94 inches and a nominal internal diameter of 73 inches, tapering outward to a nominal inside diameter of 76 inches at the OCV lower seal flange. The nominal external diameter of the OCV seal region is 95 inches, and the nominal internal diameter of the OCV seal region is 76 inches. With the OCA lid installed onto the OCA body, the OCA has a nominal external length of 91 inches, and a nominal internal height is 70 inches at the OCV cavity centerline.
The confinement boundary provided by the OCA consists of the inner stainless steel vessel formed by a mating lid and body, plus the uppermost of two optional main O-ring seals enclosed between an upper and lower seal flange. The main O-ring seals are polymer with a nominal 1
U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
1.2-1
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 3/8+/-1/8-inch diameter cross-section. The purpose of the lower main O-ring seal is for establishing a vacuum on the exterior side of the upper main O-ring seal for optional helium and/or pressure rise leakage rate testing.
A vent port feature in the OCV bodys lower seal flange is the only other confinement boundary penetration. A vent port coupling, a seal welded threaded fitting, and an OCV vent port plug with an optional O-ring seal defines the confinement boundary at the OCV vent port penetration.
Access to the OCV vent port is gained through an external penetration in the OCA outer shell once an outer 11/2 NPT plug and a foam or ceramic fiber material plug is removed. The connecting tube is fabricated of non-thermally conductive fiberglass.
Optional leakage rate testing of the OCVs optional upper main O-ring seal (confinement seal) is performed through an OCV seal test port that is located in the OCA lid. Similar in design to the OCV vent port, access to the OCV seal test port is gained through an external penetration in the OCA outer shell once an outer 11/2 NPT plug and a foam or ceramic fiber material plug is removed. The connecting tube is fabricated of thin-walled stainless steel.
The cylindrical portion of the OCV body is 3/16-inch nominal thickness, Type 304, stainless steel. All other shells comprising the OCV are 1/4-inch nominal thickness, Type 304, stainless steel, including the lower and upper torispherical heads. The OCA outer shell varies between 1/4- and 3/8-inch nominal thickness, Type 304, stainless steel. The 3/8-inch nominal thickness material is used adjacent to the closure interface to ensure protection from HAC puncture bar penetration near the sealing regions. All other shells comprising the OCA exterior are 1/4-inch nominal thickness, Type 304, stainless steel, including the lower flat head and upper torispherical head. As illustrated in Figure 1.1-2, the inner and outer shell structures for both the OCA lid and OCA body are connected together via 14-gauge (0.075-inch thick), Type 304, stainless steel Z-flanges. Secure attachment of the 14-gauge Z-flanges to the 3/8-inch thick OCA outer shell is assured by the use of rolled angle reinforcements (2 x 2 x 1/4 inches for the OCA body junction, and 1 x 1 x 1/8 inches for the OCA lid junction). A locking Z-flange between the upper and lower (i.e., OCA lid and OCA body) Z-flanges allows rotation of the OCV locking ring from the HalfPACT package exterior. The Z-flanges serve the purpose of precluding direct flame impingement on the OCV seal flanges during the hypothetical accident condition (HAC) thermal event (fire). To further preclude flame and hot gas entry into the Z-flange channel, inner and outer thermal shields are included as part of the locking Z-flange assembly.
The OCA lid is secured to the OCA body via the OCV locking ring located at the outer diameter of the OCV upper and lower seal flanges. Closure design and operation for the ICV is illustrated in Figure 1.2-1 (the OCV is similar). The lower end of the OCV locking ring has 18 tabs that mate with a corresponding set of 18 tabs on the OCV lower seal flange. To install the OCA lid, the OCV locking ring is rotated to the unlocked position, using alignment marks on the OCA exterior for reference. The unlocked position aligns the tabs on the OCV locking ring with the cutouts between the tabs on the OCV lower seal flange. Next, install the OCA lid onto the OCA body, optionally evacuating the OCV cavity through the OCV vent port sufficiently to allow free movement of the OCV locking ring. Positive closure is attained by rotating the OCV locking ring to the locked position, again using the alignment marks on the OCA exterior for reference.
In order to allow rotation of the OCV locking ring from the HalfPACT packaging exterior, a locking Z-flange extends radially outward to the OCA exterior. Six, 1/2-inch diameter, stainless steel socket head cap screws secure the locking Z-flange in the locked position. A single, localized cutout in the OCV locking ring is provided for access to the OCV seal test port feature.
1.2-2
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Within the annular void between the OCV and the OCA outer shell structure is a relatively thick layer of thermally insulating and energy absorbing, rigid, polyurethane foam. Surrounding the periphery of the polyurethane foam cavity is a layer of 1/4-inch nominal thickness, ceramic fiber paper capable of resisting temperatures in excess of 2,000 ºF. The combination of OCA exterior shell, fire resistant polyurethane foam, and insulating ceramic fiber paper is sufficient to protect the confinement boundary from the consequences of all regulatory defined tests.
Two fork lift pockets are incorporated into the base of the OCA body. These pockets provide the handling interface for lifting a HalfPACT package. Three sets of lifting straps are included in the OCA lid assembly for lifting of the OCA lid only, and are so appropriately identified. Four tie-down lugs with reinforcing doubler plates are also provided at the base of the OCA body.
Polymer materials used in the OCA include butyl, and ethylene propylene or neoprene, as applicable, for the main O-ring seals, silicone for the wear pad, and polyester foam for the optional annulus foam ring. Plastic is used for the polyurethane foam cavity, fire-consumable vent plugs, and optional guide plates. The OCA lid lift pockets, vent port access tube, and a portion of the seal test port access tube are made from fiberglass. Brass is used for the OCV vent and seal test port plugs. High alloy stainless steel is used for the OCV locking ring joint pins.
Insulating materials such as ceramic fiber paper along the periphery of the polyurethane foam cavity, and fiberglass-type insulation for the inner thermal shield are also used. Finally, a variety of stainless steel fasteners, greases and lubricants, and adhesives are also utilized, as specified in Appendix 1.3.1, Packaging General Arrangement Drawings.
1.2.1.1.2      Inner Containment Vessel (ICV) Assembly The inner containment vessel (ICV) assembly consists of an ICV lid and ICV body, each primarily comprised of a stainless steel shell structure. Not considering the seal flange region, the ICV lid has a nominal external diameter of 74 inches and a nominal internal diameter of 73 inches. Likewise, not considering the seal flange region, the ICV body has a nominal external diameter of 73 inches and a nominal internal diameter of 72 inches. The nominal external diameter of the ICV seal region is 76 inches, and the nominal internal diameter of the ICV seal region is 72 inches. With the ICV lid installed onto the ICV body, the ICV has a nominal external length of 69 inches, and a nominal internal height is 681/2 inches at the ICV cavity centerline.
The containment boundary provided by the ICV consists of a stainless steel vessel formed by a mating lid and body, plus the uppermost of two main O-ring seals enclosed between an upper and lower seal flange. The upper main O-ring seal (containment) is butyl rubber with a nominal 0.400-inch diameter cross-section. The lower main O-ring seal (test) may be neoprene or ethylene propylene with a nominal 0.375-inch diameter cross-section. The purpose of the lower main O-ring seal is for establishing a vacuum on the exterior side of the upper main O-ring seal for helium and pressure rise leakage rate testing. To protect the main O-ring seals from debris that may be associated with some payloads, a wiper O-ring seal is used between the ICV upper and lower seal flanges. In addition to the wiper O-ring seal, a silicone debris shield, located at the top of the ICV lower seal flange, provides a secondary debris barrier to the upper main O-ring seal. To ensure that helium tracer gas reaches the region directly above the upper main O-ring seal (containment) during helium leakage rate testing, a helium fill port is integral to the ICV vent port configuration (see Appendix 1.3.1, Packaging General Arrangement Drawings).
In addition, to allow for pressure equalization across the silicone debris shield during ICV lid 1.2-3
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 installation and removal, three, 1/8-inch nominal diameter holes are located in the top of the ICV lower seal flange.
A vent port feature in the ICV bodys lower seal flange is the only other containment boundary penetration. A vent port insert and an outer ICV vent port plug with an O-ring seal define the containment boundary at the ICV vent port penetration.
Leakage rate testing of the ICVs upper main O-ring seal (containment seal) is performed through an ICV seal test port that is located in the ICV lid.
All shells comprising the ICV are 1/4-inch nominal thickness, Type 304, stainless steel, including the lower and upper torispherical heads.
The ICV lid is secured to the ICV body via the ICV locking ring located at the outer diameter of the ICV upper and lower seal flanges. Closure design and operation is illustrated in Figure 1.2-1.
The lower end of the ICV locking ring has 18 tabs that mate with a corresponding set of 18 tabs on the ICV lower seal flange. To install the ICV lid, the ICV locking ring is rotated to the unlocked position, using alignment marks for reference. The unlocked position will align the tabs on the ICV locking ring with the cutouts between the tabs on the ICV lower seal flange.
Next, the ICV lid is installed onto the ICV body, optionally evacuating the ICV cavity through the ICV vent port sufficiently to allow free movement of the ICV locking ring. Positive closure is attained by rotating the ICV locking ring to the locked position, using the alignment marks for reference. Three, 1/2-inch diameter, stainless steel socket head cap screws secure the ICV locking ring in the locked position.
Three lift sockets, each containing a lift pin, are integrated into the ICV lid for lifting the ICV lid or an empty ICV assembly. Any lifting of the loaded ICV is performed using the OCA forklift pockets with the ICV located within the OCA.
Polymer materials used in the ICV include butyl, ethylene propylene, neoprene, buna-N, flourosilicone or flourocarbon, as applicable, for the main and wiper O-ring seals, and silicone for the debris shield. Brass is used for the ICV vent and seal test port plugs. High alloy stainless steel is used for the ICV locking ring joint pins. Finally, a variety of stainless steel fasteners, and greases and lubricants are also utilized, as specified in Appendix 1.3.1, Packaging General Arrangement Drawings.
1.2.1.1.3      Aluminum Honeycomb Spacer Assemblies Aluminum honeycomb spacer assemblies are designed to fit within the torispherical heads at each end of the ICV cavity. Each aluminum honeycomb spacer assembly includes an optional, 18-inch nominal diameter by 11/2-inch nominal depth pocket that may be used in the future to accommodate a catalyst assembly. The lower spacer assembly also includes a 3-inch nominal diameter hole at the center that serves as an inspection port to check for water accumulation in the ICV lower head.
With the spacer assemblies in place, the nominal ICV cavity height becomes 44 inches.
1.2.1.2    Gross Weight The gross shipping weight of a HalfPACT package is 18,100 pounds maximum. A summary of overall component weights is delineated in Table 2.2-1 of Section 2.2, Weights and Centers of Gravity.
1.2-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 1.2.1.3    Neutron Moderation and Absorption The HalfPACT package does not require specific design features to provide neutron moderation and absorption for criticality control. Fissile materials in the payload are limited to amounts that ensure safely subcritical packages for both NCT and HAC. The fissile material limits for a single HalfPACT package are based on optimally moderated and reflected fissile material. The structural materials in the HalfPACT packaging are sufficient to maintain reactivity between the fissile material in an infinite array of damaged HalfPACT packages at an acceptable level.
Further discussion of neutron moderation and absorption is provided in Chapter 6.0, Criticality Evaluation.
1.2.1.4    Receptacles, Valves, Testing, and Sampling Ports There are no receptacles or valves used on the HalfPACT packaging, however, the OCV and ICV each have a seal test port and a vent port (see Appendix 1.3.1, Packaging General Arrangement Drawings). For each containment/confinement vessel, a seal test port provides access to the region between the upper and lower (containment/confinement and test) main O-ring seals between the upper and lower (lid and body) seal flanges. The seal test ports are used to leakage rate test the upper main ICV seal and, if used, the optional upper main OCV seal to verify proper assembly of the HalfPACT package prior to shipment.
The vent port is used during loading and unloading to facilitate lid installation and removal, and to allow blowdown of internal vacuum or pressure prior to opening a loaded package. As an option, a low vacuum may be applied to the vent port to fully seat the lid and assure free rotation of the locking ring.
Two separate penetrations through the polyurethane foam within the OCA are provided to access the seal test port and vent port plugs. The access ports are capped at the OCA exterior surface with 11/2-inch pipe plugs (NPT) within 3-inch diameter couplings. Reinforcing doubler plates are also included on the inner surface of the OCA exterior shell, adjacent to the couplings. In addition, removable foam or ceramic fiber plugs fill the region within the access hole tubes to provide a level of thermal protection from the HAC thermal event. The vent port access tube is comprised of a non-metallic fiberglass, and a fiberglass link is included with the stainless steel, seal test port access tube as a lining to reduce radial thermal conductivity. When the OCA lid is removed, the ICV vent and seal test port plugs are readily accessible.
The OCV seal test port and both the ICV seal test and vent port plugs are accessed through localized cutouts in the corresponding vessel locking rings. An elongated cutout in the ICV locking ring is utilized at the ICV vent port location to allow locking ring rotation while an optional vacuum pump is installed. Smaller cutouts are provided in the ICV and OCV locking rings at the seal test port locations since these ports are only used with the locking rings in the locked position. The OCV vent port feature is located in the OCA body, therefore a cutout in the OCV locking ring is not necessary.
Detailed drawings of the test and vent port features and the associated local cutouts in the locking rings are provided in Appendix 1.3.1, Packaging General Arrangement Drawings.
1.2.1.5    Heat Dissipation The HalfPACT package design capacity is 30 thermal watts maximum. The HalfPACT package dissipates this relatively low internal heat load entirely by passive heat transfer for both NCT and 1.2-5
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 HAC. No special devices or features are needed or utilized to enhance the dissipation of heat.
Features are included in the design to enhance thermal performance in the HAC thermal event.
These include the use of a high temperature insulating material (ceramic fiber paper) at polyurethane foam-to-steel interfaces and the presence of an inner and outer thermal shield at the OCA lid-to-body interface. A more detailed discussion of the package thermal characteristics is provided in Chapter 3.0, Thermal Evaluation.
1.2.1.6      Coolants Due to the passive design of the HalfPACT package with regard to heat transfer, there are no coolants utilized within the HalfPACT package.
1.2.1.7      Protrusions The only significant protrusions on the HalfPACT package exterior are those associated with the lifting and tie-down features on the OCA exterior. The only significant external protrusions from the OCA lid are lift straps and corresponding guide pockets that extend from three equally spaced locations at the lid top. These lift features protrude above the OCA upper torispherical head, but are radially located such that they remain below torispherical heads crown and do not affect overall package height. The guide pockets are made of a fiberglass material that is designed to break away for lid-end impacts. The only significant external protrusions from the OCA body are the tie-down features at the bottom end of the package. Four tie-down lugs, with associated doubler plates, are used at locations corresponding with the main beams of the trailer. These tie-down protrusions extend a maximum of 2 inches radially from the OCA body exterior shell.
The only significant protrusion on the ICV exterior is the ICV locking ring. The ICV locking ring extends radially outward approximately one inch from the outside surface of the upper ICV torispherical head. With its 3-inch axial length directly backed and supported by the OCV (the nominal radial gap is 1/4 inch), this external protrusion is of little consequence for the package.
The only significant protrusions on the ICV interior are the three lift pockets that penetrate the upper ICV torispherical head. These lift pockets are equally spaced on a 56-inch diameter, extending into the ICV cavity a maximum of 41/2 inches from the inner surface of the upper ICV torispherical head. The ICV lift pockets are of little consequence as they are protected by the surrounding aluminum honeycomb spacer assembly. There are no significant internal or external protrusions associated with the ICV body.
1.2.1.8      Lifting and Tie-down Devices Three sets of lift pins, lift straps and associated doubler plates used in the OCA lid are designed to handle the OCA lid only (including overcoming any resistance to lid removal associated with the presence of the main O-ring seals). The OCA lid lifting devices are not designed to lift a loaded package or empty OCA. Under excessive load, failure occurs in the region of the OCA lift pin locations (at the pin-to-strap welds), away from the OCA torispherical head. A loaded HalfPACT package or any portion thereof can be lifted via the pair of fork lift pockets that are located at the base of the OCA body. These pockets are sized to accommodate forks up to 10 inches wide and up to 4 inches thick. An overhead crane can also be used to lift the loaded package, utilizing lifting straps, through the fork lift pockets.
Lifting of the ICV is via the three lift pockets inset into the upper ICV torispherical head. These lift pockets, with their associated lift pins and adjacent doubler plates, are sized to lift an empty 1.2-6
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 ICV or handle the ICV lid (including overcoming any resistance to lid removal associated with the presence of the main O-ring seals). A loaded ICV must be fully supported with the OCA body and lifted via the OCA fork lift pockets. Under excessive load, the ICV lift pins are designed to fail in shear prior to compromising the ICV containment boundary.
Both the OCA and ICV lifting points are appropriately labeled to limit their use to the intended manner.
Four tie-down lugs, with associated doubler plates, are used at locations corresponding with the main beams of the trailer. At each tie-down location, one doubler is used on the outside surface of the OCA side wall and one on the inside surface of the OCA lower flanged head. At each tie-down lug location, an internal gusset plate is also used between the inside of the OCA exterior shell and the doubler in the lower head to stiffen the tie-down regions. The doubler plates are sized to adequately distribute the regulatory-defined tie-down loads (10 gs longitudinal, 5 gs lateral, and 2 gs vertical, applied simultaneously) outwardly into the 1/4-inch thick OCA exterior shell. Each tie-down lug is welded directly to the adjacent side doubler plate. In an excessive load condition, these tie-down lug welds are sized to shear from the corresponding doubler plate.
A detailed discussion of lifting and tie-down designs, with corresponding structural analyses, is provided in Section 2.5, Lifting and Tie-down Standards for All Packages.
1.2.1.9    Pressure Relief System There are no pressure relief systems included in the HalfPACT package design to relieve pressure from within the ICV or OCV. Fire-consumable vents in the form of plastic pipe plugs are employed on the exterior surface of the OCA. These vents are included to release any gases generated by charring polyurethane foam in the HAC thermal event (fire). During the HAC fire, the plastic pipe plugs melt allowing the release of gasses generated by the foam as it flashes to a char. Three vents are used on the OCA lid and six on the OCA body, located at the center of foam mass in each component. For optimum performance, the vents are located uniformly around the circumference of the OCA lid and body.
1.2.1.10 Shielding Due to the nature of the contact-handled transuranic (CH-TRU) payload, no biological shielding is necessary or provided by the HalfPACT packaging.
1.2.2      Operational Features The HalfPACT package is not considered to be operationally complex. All operational features are readily apparent from an inspection of the drawings provided in Appendix 1.3.1, Packaging General Arrangement Drawings, and the previous discussions presented in Section 1.2.1, Packaging. Operational procedures and instructions for loading, unloading, and preparing an empty HalfPACT package for transport are provided in Chapter 7.0, Operating Procedures.
1.2.3      Contents of Packaging The HalfPACT packaging is designed to transport contact-handled transuranic (CH-TRU) and other authorized payloads such as tritium-contaminated materials that do not exceed 105 A2 quantities. The Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC)1 is the governing document for shipments of solid or solidified CH-TRU and tritium-contaminated 1.2-7
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 wastes in the HalfPACT package. All users of the HalfPACT package shall comply with all payload requirements outlined in the CH-TRAMPAC, using one or more of the methods described in that document.
1.2-8
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Figure 1.2 ICV Closure Design (OCV closure is similar) 1.2-9
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
1.2-10
 
HalfPACT Safety Analysis Report                Rev. 9, August 2022 1.3 Appendices 1.3.1 Packaging General Arrangement Drawings 1.3.2 Glossary of Terms and Acronyms 1.3-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
1.3-2
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 1.3.1      Packaging General Arrangement Drawings This section presents the HalfPACT packaging general arrangement drawing 1, consisting of 12 sheets entitled, HalfPACT Packaging SAR Drawing, Drawing Number 707-SAR. In addition, the standard pipe overpack general arrangement drawing, consisting of 3 sheets entitled, Standard Pipe Overpack, Drawing Number 163-001, is presented in this section. The S100 pipe overpack, the S200 pipe overpack, and the S300 pipe overpack are depicted in Drawing Numbers 163-002, 163-003, and 163-004, respectively. The 55-gallon, 85-gallon, and 100-gallon compacted puck drum spacers are depicted in Drawing Number 163-006. The SC-30G1 and associated dunnage assembly are depicted in Drawing Number 163-008. The criticality control overpack is depicted in Drawing Number 163-009. The SC-30G2 and associated dunnage assembly are depicted in Drawing Number 163-010. The SC-30G3 and associated dunnage assembly are depicted in Drawing Number 163-011. The SC-55G1 and associated dunnage assembly are depicted in Drawing Number 163-012. The SC-55G2 and associated dunnage assembly are depicted in Drawing Number 163-013.
Within the packaging general arrangement drawing, dimensions important to the packagings safety are dimensioned and toleranced (e.g., structural shell thicknesses, polyurethane foam thicknesses, and the sealing regions on the seal flanges). All other dimensions are provided as a reference dimension, and are toleranced in accordance with the general tolerance block.
1 The HalfPACT packaging, pipe overpack, compacted puck drum spacer, and shielded container general arrangement drawings utilize the uniform standard practices of ASME Y14.5M, Dimensioning and Tolerancing, American National Standards Institute, Inc. (ANSI).
1.3.1-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
1.3.1-2
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.        *-
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
f-Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
Official Use Only - Security-Related Information Figure Withheld Per 10 CFR 2.390.
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 This page intentionally left blank.
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 1.3.2      Glossary of Terms and Acronyms 55-Gallon Drum - A payload container yielding 55 gallons.
85-Gallon Drum - A payload container with a range of dimensions yielding 75 to 88 gallons.
85-Gallon Drum Overpacks - A payload container consisting of a 55-gallon drum overpacked within an 85-gallon drum of the appropriate dimensions.
100-Gallon Drum - A payload container yielding 100 gallons.
Aluminum Honeycomb Spacer Assembly - An assembly that is located within each end of the ICV. The aluminum honeycomb spacer assembly supplements the ICV void volume to accommodate gas generated by the payload material, and acts as an energy-absorbing barrier between the payload and the ICV torispherical heads for axial loads.
ASME - American Society of Mechanical Engineers.
ASME B&PVC - ASME Boiler and Pressure Vessel Code.
CCO - Criticality Control Overpack CCC - Criticality Control Container CTU - Certification Test Unit CH-TRAMPAC - Contact-Handled Transuranic Waste Authorized Methods for Payload Control.
CH-TRU Waste - Contact-Handled Transuranic Waste.
HalfPACT Package - The package consisting of a HalfPACT packaging and the Payload.
HalfPACT Packaging - The packaging consisting of an outer confinement assembly (OCA), an inner containment vessel (ICV), and two aluminum honeycomb spacer assemblies.
ETU - Engineering Test Unit.
ICV - Inner Containment Vessel.
ICV Body - The assembly consisting of the ICV lower seal flange, the cylindrical vessel, and the ICV lower torispherical head.
ICV Inner Vent Port Plug - The brass plug and accompanying O-ring seal that provides the pressure boundary in the ICV vent port penetration.
ICV Lid - The assembly consisting of the ICV upper seal flange, the ICV locking ring, a short section of cylindrical vessel, and the ICV upper torispherical head.
ICV Lock Bolts - The three, 1/2-inch, socket head cap screws used to secure the ICV locking ring in the locked position.
ICV Locking Ring - The component that connects and locks the ICV upper seal flange to the ICV lower seal flange; included as an ICV lid component.
ICV Lower Seal Flange - The ICV bodys sealing interface containing two O-ring grooves, the ICV vent port access, and the ICV test port.
1.3.2-1
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 ICV Main O-ring Seal - The upper elastomeric O-ring seal in the ICV lower seal flange; forms the containment boundary.
ICV Outer Vent Port Plug - The brass plug and accompanying O-ring seal that provides the containment boundary in the ICV vent port penetration.
ICV Seal Test Port - The radial penetration between the ICV main O-ring seal and ICV main test O-ring seal to allow leakage rate testing of the ICV main O-ring seal.
ICV Seal Test Port Plug - The brass plug and accompanying O-ring seal for the ICV seal test port.
ICV Seal Test Port Insert - A welded-in, replaceable component within the ICV lower seal flange that interfaces with the ICV seal test port plug.
ICV Main Test O-ring Seal - The lower elastomeric O-ring seal in the ICV lower seal flange; forms the test boundary for leakage rate testing.
ICV Upper Seal Flange - The ICV lids sealing interface containing a mating sealing surface for the ICV lower seal flange and location for a wiper O-ring seal.
ICV Vent Port - The radial penetration into the ICV cavity that is located in the ICV lower seal flange.
ICV Vent Port Cover - The outer brass cover that directly protects the ICV vent port plugs.
Inner Containment Vessel - The assembly (comprised of an ICV lid and ICV body) providing the primary level of containment for the payload. Within each end of the inner containment vessel (ICV) is an aluminum honeycomb spacer assembly.
Locking Z-Flange - The z-shaped shell situated between the upper and lower Z-flanges that connects to the OCV locking ring; allows external operation of the OCV locking ring.
Lower Z-Flange - The z-shaped shell in the OCA body, connecting the OCA outer shell to the OCV lower seal flange.
OCA - Outer Confinement Assembly.
OCA Body - The assembly consisting of the OCV lower seal flange, the OCV cylindrical and conical shells, the OCV lower torispherical head, the lower Z-flange, the OCA cylindrical shell, the OCA lower flat head, corner reinforcing angles, tie-down structures, ceramic fiber paper, and polyurethane foam.
OCA Inner Thermal Shield - The L-shaped, 16-gauge (0.060-inch thick), inner shield that holds fiberglass insulating material against the OCV locking ring thereby preventing hot gasses and flames from directly impinging on the OCV sealing region in the event of a HAC fire.
OCA Lid - The assembly consisting of the OCV upper seal flange, the OCV locking ring, a short section of cylindrical vessel, the OCV upper torispherical head, the upper and locking Z-flanges, the inner and outer thermal shields, a short section of cylindrical shell, the OCA upper torispherical head, corner reinforcing angles, ceramic fiber paper, and polyurethane foam.
OCA Lock Bolts - The six 1/2-inch, socket head cap screws used to secure the OCV locking ring in the locked position.
OCA Lower Head - The lower ASME flat head comprising the OCA outer shell.
1.3.2-2
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 OCA Outer Thermal Shield - The 14-gauge (0.075-inch thick) x 6-inch wide outer shield surrounding the OCA lid-to-body joint that prevents hot gasses and flames from entering the joint in the event of a HAC fire.
OCA Upper Head - The upper ASME torispherical head comprising the OCA outer shell.
OCV - Outer Confinement Vessel.
OCV Locking Ring - The component that connects and locks the OCV upper seal flange to the OCV lower seal flange; included as an OCA lid component.
OCV Lower Seal Flange - The OCA bodys sealing interface containing two O-ring grooves.
OCV Main O-ring Seal - The optional upper O-ring seal in the OCV lower seal flange; forms the confinement boundary.
OCV Main Test O-ring Seal - The optional lower O-ring seal in the OCV lower seal flange; forms the test boundary for optional leakage rate testing.
OCV Seal Test Port - The radial penetration between the OCV main O-ring seal and OCV main test O-ring seal to allow optional leakage rate testing of the OCV main O-ring seal.
OCV Seal Test Port Access Plug - The 11/2-inch NPT plug located at the outside end of the OCV seal test port access tube (i.e., at the outside surface of the OCA lid outer shell).
OCV Seal Test Port Insert - A welded-in, replaceable component within the OCV lower seal flange that interfaces with the OCV seal test port plug.
OCV Seal Test Port Plug - The brass plug and accompanying optional O-ring seal for the OCV seal test port.
OCV Seal Test Port Thermal Plug - The foam or ceramic fiber plug located within the OCV seal test port access tube that thermally protects the OCV seal test port region.
OCV Upper Seal Flange - The OCA lids sealing interface containing a mating sealing surface for the OCV lower seal flange.
OCV Vent Port - The radial penetration into the OCV cavity that is located in the OCV conical shell.
OCV Vent Port Access Plug - The 11/2-inch NPT plug located at the outside end of the OCV vent port access tube (i.e., at the outside surface of the OCA body outer shell).
OCV Vent Port Access Tube - The fiberglass tube allowing external access to the OCV vent port.
OCV Vent Port Cover - The outer brass cover that directly protects the OCV vent port plug.
OCV Vent Port Plug - The brass plug and accompanying optional O-ring seal that provides the confinement boundary in the OCV vent port penetration.
OCV Vent Port Thermal Plug - The foam or ceramic fiber plug located within the OCV vent port access tube that thermally protects the OCV vent port region.
Outer Confinement Assembly - The assembly (comprised of an OCA lid and OCA body) providing a secondary level of confinement for the payload when its optional O-ring seals are utilized. The Outer Confinement Assembly (OCA) completely surrounds the Inner Containment 1.3.2-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Vessel and consists of an exterior stainless steel shell, a relatively thick layer of polyurethane foam and an inner stainless steel boundary that forms the Outer Confinement Vessel (OCV).
Outer Confinement Vessel - The innermost boundary of the Outer Confinement Assembly.
Packaging - The assembly of components necessary to ensure compliance with packaging requirements as defined in 10 CFR §71.4. Within this SAR, the packaging is denoted as the HalfPACT packaging.
Package - The packaging with its radioactive contents, or payload, as presented for transportation as defined in 10 CFR §71.4. Within this SAR, the package is denoted as the HalfPACT contact-handled transuranic waste package, or equivalently, the HalfPACT package.
Payload - Contact-handled transuranic (CH-TRU) waste or other authorized contents such as tritium-contaminated materials contained within approved payload containers. In this SAR, the payload includes a payload pallet for handling when drums are used. Any additional dunnage used that is external to the payload containers is also considered to be part of the payload. Payload requirements are defined by the CH-TRAMPAC.
Payload Container - Payload containers may be 55-gallon drums, pipe overpacks, criticality control overpacks (CCOs), 85-gallon drums (including overpacks), 100-gallon drums, standard waste boxes (SWB), or shielded containers (SC).
Payload Pallet - A lightweight pallet used for handling drum-type payload containers.
Payload Spacer - A component of the same basic design as the payload pallet; used to control (reduce) vertical clearance within the ICV with 55-gallon drum, short 85-gallon drum, 100-gallon drum, and SWB payload containers.
Pipe Component - A stainless steel container used for packaging specific waste forms within a 55-gallon drum. The pipe component is exclusively used as part of the pipe overpack.
Pipe Overpack - A payload container consisting of a pipe component positioned by dunnage within a 55-gallon drum with a rigid, polyethylene liner and lid. Seven pipe overpack assemblies will fit within the HalfPACT packaging.
RTV - Room Temperature Vulcanizing.
SAR - Safety Analysis Report (this document).
Shielded Container - Specialized payload containers (i.e., SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2) for use within the HalfPACT packaging that provide gamma shielding.
Up to three shielded containers are surrounded by radial, axial, and/or lateral dunnage assemblies and loaded using a payload pallet within the HalfPACT packaging.
Standard Waste Box - A specialized payload container for use within the HalfPACT packaging. One standard waste box can fit within the HalfPACT packaging.
SWB - Standard Waste Box.
Upper Z-Flange - The z-shaped shell in the OCA lid, connecting the OCA outer shell to the OCV upper seal flange.
1.3.2-4
 
HalfPACT Safety Analysis Report                                                            Rev. 9, August 2022 2.0 STRUCTURAL EVALUATION This section presents evaluations demonstrating that the HalfPACT package meets all applicable structural criteria. The HalfPACT packaging, consisting of an outer confinement assembly (OCA), with an integral outer confinement vessel (OCV), and an inner containment vessel (ICV), with aluminum honeycomb spacer assemblies, is evaluated and shown to provide adequate protection for the payload. Normal conditions of transport (NCT) and hypothetical accident condition (HAC) evaluations, using analytic and empirical techniques, are performed to address 10 CFR 71 1 performance requirements. Analytic demonstration techniques comply with the methodology presented in NRC Regulatory Guides 7.6 2 and 7.8 3.
The HalfPACT package possesses strong similarities with the licensed TRUPACT-II package (NRC Certificate of Compliance No. 9218). All features of the HalfPACT package are essentially identical to those of the TRUPACT-II package. The only major exception is the removal of 30 inches of cylindrical sidewall length from the OCA and ICV bodies.
Numerous component and scale tests were successfully performed on the TRUPACT-II package during its development phase. Subsequent TRUPACT-II certification testing involved three, full scale certification test units (CTUs). The TRUPACT-II CTUs were subjected to a series of free drop and puncture drop tests, and two of the three TRUPACT-II CTUs were subjected to fire testing. Despite the great degree of similarity between the HalfPACT and TRUPACT-II packages, a full scale HalfPACT engineering test unit (ETU) and CTU were also subjected to a series of free drop, puncture drop, and fire tests. Both the HalfPACT ETU and CTU remained leaktight 4 throughout certification testing. Details of the certification test program are provided in Appendix 2.10.3, Certification Tests.
2.1 Structural Design 2.1.1        Discussion A comprehensive discussion on the HalfPACT package design and configuration is provided in Section 1.2, Package Description. Specific discussions relating to the aspects important to demonstrating the structural configuration and performance to design criteria for the HalfPACT package are provided in the following sections. Standard fabrication methods are utilized to fabricate the HalfPACT packaging.
1 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 U. S. Nuclear Regulatory Commission, Regulatory Guide 7.6, Design Criteria for the Structural Analysis of Shipping Cask Containment Vessels, Revision 1, March 1978.
3 U. S. Nuclear Regulatory Commission, Regulatory Guide 7.8, Load Combinations for the Structural Analysis of Shipping Casks for Radioactive Material, Revision 1, March 1989.
4 Leaktight is defined as leakage of 1 x 10-7 standard cubic centimeters per second (scc/s), air, or less per ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
2.1-1
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 2.1.1.1      Containment Vessel Structure (ICV)
The containment vessel cylindrical shell structure is fabricated in accordance with the tolerance requirements of the ASME Boiler and Pressure Vessel Code, Section III 5, Division 1, Subsection NE, Article NE-4220, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. The containment vessel shell-to-shell joints are fabricated in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-4230, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
All containment vessel heads are flanged torispherical heads, fabricated in accordance with the ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 6, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
All seal flange material is ultrasonically or radiographically test inspected in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-2500 and Section V 7, Article 5 (ultrasonic) or Article 2 (radiograph), as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
Circumferential and longitudinal welds for the containment vessel shells, seal flanges, and locking ring are full penetration welds, subjected to visual and liquid penetrant examinations, and radiographically test inspected, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. Visual weld examinations are performed in accordance with AWS D1.6 8. Liquid penetrant examinations are performed on the final pass in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-5000 and Section V, Article 6. Radiograph test inspections are performed in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-2500 and Section V, Article 2.
For the ICV vent port penetration, and lifting sockets, liquid penetrant examinations are performed on the final pass for single pass welds and on the root and final passes for multipass welds in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-5000 and Section V, Article 6, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
The maximum weld reinforcement for containment vessel welds shall be 3/32-inch in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-4426, Paragraph NB-4426.1, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
5 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, 1995 Edition, 1997 Addenda.
6 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section VIII, Division 1, Rules for Construction of Pressure Vessels, 1995 Edition, 1997 Addenda.
7 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section V, Nondestructive Examination, 1995 Edition, 1997 Addenda.
8 ANSI/AWS D1.6, Structural Welding Code - Stainless Steel, American Welding Society (AWS).
2.1-2
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 2.1.1.2      Non-Containment Vessel Structures (OCV and OCA)
All non-containment vessel shell-to-shell joints and transitions in thickness, such as from the 1/4-inch thick OCV lower head to the 3/16-inch thick OCV shell and the 3/8-to-1/4-inch thick OCA outer shell transition, are fabricated in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NF, Article NF-4230, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
The OCV has a top and bottom, flanged torispherical head, and the OCA outer shell has a top, flanged torispherical head and bottom, flanged flat head that are fabricated in accordance with the ASME Boiler and Pressure Vessel Code, Section VIII, Division 1, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
Circumferential and longitudinal welds for the non-containment vessel shells are full penetration welds, subjected to visual and liquid penetrant examinations, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. Visual weld examinations are performed in accordance with AWS D1.6. Liquid penetrant examinations are performed on the final pass in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NF, Article NF-5000.
The maximum weld reinforcement for non-containment vessel welds shall be 3/32 inch in accordance with the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NF, Article NF-4400, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
2.1.2      Design Criteria Proof of performance for the HalfPACT package is achieved by a combination of analytic and empirical evaluations. The acceptance criteria for analytic assessments are in accordance with Regulatory Guide 7.6 and Section III of the ASME Boiler and Pressure Vessel Code. The acceptance criterion for empirical assessments is a demonstration that the containment boundary remains leaktight throughout NCT and HAC certification testing. Additionally, package deformations obtained from certification testing must be such that deformed geometry assumptions used in subsequent thermal, shielding, and criticality evaluations are validated.
The remainder of this section presents the detailed acceptance criteria used for all analytic structural assessments of the HalfPACT package.
2.1.2.1      Analytic Design Criteria (Allowable Stresses)
This section defines the stress allowables for primary membrane, primary bending, secondary, shear, peak, and buckling stresses for containment and non-containment structures. These stress allowables are used for all analytic assessments of HalfPACT package structural performance. Regulatory Guide 7.6 is used in conjunction with Regulatory Guide 7.8 to evaluate the package integrity.
Material yield strengths used in the analytic acceptance criteria, Sy, ultimate strengths, Su, and design stress intensity values, Sm, are presented in Table 2.3-1 of Section 2.3, Mechanical Properties of Materials.
2.1-3
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 2.1.2.1.1      Containment Structure (ICV)
A summary of allowable stresses used for containment structures is presented in Table 2.1-1.
These data are consistent with Regulatory Guide 7.6, and the ASME Boiler and Pressure Vessel Code, Section III, Subsection NB-3000 and Appendix F.
2.1.2.1.2      Non-Containment Structures (OCV and OCA)
A summary of allowable stresses used for non-containment structures is presented in Table 2.1-2.
For conservatism, the allowable stresses applicable to containment structures presented in Table 2.1-1 are utilized for OCV evaluations.
For evaluation of lifting devices, the allowable stresses are limited to one-third of the material yield strength, consistent with the requirements of 10 CFR §71.45(a). For evaluation of tie-down devices, the allowable stresses are limited to the material yield strength, consistent with the requirements of 10 CFR §71.45(b).
For evaluations involving polyurethane foam, primary, load controlled compressive stresses are limited to two-thirds of the parallel-to-rise or perpendicular-to-rise compressive strength (as applicable) at 10% strain. Use of a two-thirds factor on compressive strength ensures elastic behavior of the polyurethane foam.
2.1.2.2      Miscellaneous Structural Failure Modes 2.1.2.2.1      Brittle Fracture By avoiding the use of ferritic steels in the HalfPACT packaging, brittle fracture concerns are precluded. Specifically, most primary structural components are fabricated of Type 304 austenitic stainless steel. Since this material does not undergo a ductile-to-brittle transition in the temperature range of interest (down to -40 ºF), it is safe from brittle fracture.
The lock bolts used to secure the ICV and OCV locking rings in the locked position are stainless steel, socket head cap screws ensuring that brittle fracture is not of concern. Other fasteners used in the HalfPACT packaging assembly, such as the 36, 1/4-inch screws attaching the locking Z-flange to the OCV locking ring, provide redundancy and are made from stainless steel, again eliminating brittle fracture concerns.
2.1.2.2.2      Fatigue Assessment 2.1.2.2.2.1      Normal Operating Cycles Normal operating cycles do not present a fatigue concern for the various HalfPACT packaging components. Most HalfPACT packaging components exhibit little-to-no stress concentrations, and by satisfying the allowable limit for range of primary-plus-secondary stress intensity for NCT (3.0Sm), the allowable fatigue stress limit for the expected number of operating cycles is satisfied. For HalfPACT packaging components that do exhibit stress concentrations, stresses are low enough that allowable fatigue stress limits are again satisfied.
The maximum number of operating cycles reasonably expected for the HalfPACT package is 3,640, and is based on two round trips per week for 35 years. Conservatively, 5,000 cycles (or in excess of 1 cycle every 3 days) is used in the following calculations. A cycle is defined as the process of the internal pressure within the ICV increasing gradually from zero psig at the time of 2.1-4
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 loading, to 50 psig (the maximum normal operating pressure, MNOP, per Section 3.4.4, Maximum Internal Pressure) during transport and then returning to 0 psig when the containment vessel is vented prior to unloading the payload. This scenario is conservative because most shipments will never generate pressure to the magnitude of the MNOP, and the system could never achieve MNOP in less than the assumed transportation cycle of three days.
From Figure I-9.2.1 and Table I-9.1 of the ASME Boiler and Pressure Vessel Code 9, the fatigue allowable alternating stress intensity amplitude, Sa, for 5,000 cycles is 76,000 psi. This value, when multiplied by the ratio of elastic hot NCT modulus at 160 ºF (the package wall temperature from Section 2.6.1, Heat) to a modulus at 70 ºF, 27.8(10)6/28.3(10)6, results in a fatigue allowable alternating stress intensity amplitude at 160 °F of 74,657 psi. The non-fatigue allowable stress intensity range, from the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB-3222.2, is 60,000 psi (3.0Sm, where Sm is 20,000 psi from Table 2.3-1 in Section 2.3, Mechanical Properties of Materials, at 160 ºF). The alternating stress intensity is one-half of this range, or 30,000 psi. Thus, in the absence of stress concentrations, the fatigue allowable alternating stress intensity will not govern the HalfPACT packaging design.
Regions of stress concentrations for the package occur in the ICV and OCV seal flanges and locking rings. The maximum range of primary-plus-secondary stress intensity occurs between the case of maximum internal pressure under NCT hot conditions (see Section 2.6.1.3, Stress Calculations) and the vacuum case. For the seal flanges or locking rings the maximum primary-plus-secondary stress intensity is 27,922 psi from Table 2.6-5 (ICV Load Case 1). The stress range is therefore 27,922 psi.
In accordance with Paragraph C.3 of Regulatory Guide 7.6, a stress concentration factor of four will conservatively be applied to the value of maximum stress intensity from above. The resultant range of peak stress intensity, correcting the modulus of elasticity for temperature, becomes:
28.3(10 )6 S range = (27,922)(4 )              = 113,697 psi 27.8(10 )
6 where the modulus of elasticity at 70 ºF is 28.3(10)6 psi, and the modulus of elasticity at 160 ºF is 27.8(10)6 psi, both from Table 2.3-1 in Section 2.3, Mechanical Properties of Materials. The alternating stress intensity is one-half of this range, or:
1 S alt =  113,697 = 56,849 psi 2
From Figure I-9.2.1 and Table I-9.1 of the ASME Boiler and Pressure Vessel Code, the allowable number of cycles for an alternating stress intensity amplitude of 56,849 psi is 16,627, or 233% more than the 5,000 cycles conservatively considered herein.
2.1.2.2.2.2      Normal Vibration Over the Road Fatigue associated with normal vibration over the road is addressed in Section 2.6.5, Vibration.
9 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, Appendix I, Design Stress Intensity Values, Allowable Stresses, Material Properties, and Design Fatigue Curves, 1995 Edition, 1997 Addenda.
2.1-5
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 2.1.2.2.2.3      Extreme Total Stress Intensity Range Per paragraph C.7 of Regulatory Guide 7.6:
The extreme total stress intensity range (including stress concentrations) between the initial state, the fabrication state, the normal operating conditions, and the accident conditions should be less than twice the adjusted value (adjusted to account for modulus of elasticity at the highest temperature) of Sa at 10 cycles given by the appropriate design fatigue curves.
Since the response of the HalfPACT package to accident conditions is typically evaluated empirically rather than analytically, the extreme total stress intensity range has not been quantified. However, the full scale certification test unit (see Appendix 2.10.3, Certification Tests) was tested at relatively low ambient temperatures during free drop and puncture testing, as well as exposure to a fully engulfing pool fire event. The CTU was also fabricated in accordance with the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings, thus incurring prototypic fabrication induced stresses, increased internal pressure equal to 150% of MNOP during fabrication pressure testing, and reduced internal pressure (i.e., a full vacuum during leak testing) conditions as part of initial acceptance. Exposure to these extreme conditions while demonstrating leaktight containment resulting from certification testing satisfies the intent of the previously defined extreme total stress intensity range requirement.
2.1.2.2.3      Buckling Assessment Buckling, per Regulatory Guide 7.6, is an unacceptable failure mode for the ICV. The intent of this provision is to preclude large deformations that would compromise the validity of linear analysis assumptions and quasi-linear stress allowables, as given in Paragraph C.6 of Regulatory Guide 7.6.
Buckling prevention criteria is applicable to the ICV containment boundary within the HalfPACT packaging. For conservatism, the criteria is also applied to the OCV confinement boundary. Shells for both vessels incorporate cylindrical mid-sections with torispherical heads at each end. The different geometric regions are considered separately to demonstrate that buckling will not occur for the two vessels. The methodology of ASME Boiler and Pressure Vessel Code Case N-284-1 10 is applied for the cylindrical regions of the containment and confinement vessels (buckling analysis details are provided in Section 2.7.6, Immersion - All Packages). The methodology of the ASME Boiler and Pressure Vessel Code, Section III, Subsection NE, is applied for the torispherical heads.
Consistent with Regulatory Guide 7.6 philosophy, factors of safety corresponding to ASME Boiler and Pressure Vessel Code, Level A and Level D service conditions are employed for NCT and HAC loadings, respectively, with factors of safety of 2.00 and 1.34, respectively.
It is also noted that 30-foot drop tests performed on full scale models with the package in various orientations produced no evidence of buckling of any of the ICV and OCV shells (see Appendix 2.10.3, Certification Tests). Certification testing does not provide a specific determination of the margin of safety against buckling, but is considered as evidence that buckling will not occur.
10 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, Division 1, Class MC, Code Case N-284-1, Metal Containment Shell Buckling Design Methods, 1995 Edition, 1997 Addenda.
2.1-6
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Table 2.1 Containment Structure Allowable Stress Limits Stress Category                  NCT                          HAC General Primary Membrane              Sm                  Lesser of:    2.4Sm Stress Intensity                                                  0.7Su Local Primary Membrane            1.5Sm                Lesser of:    3.6Sm Stress Intensity                                                      Su Primary Membrane + Bending            1.5Sm                Lesser of:    3.6Sm Stress Intensity                                                      Su Range of Primary + Secondary          3.0Sm                      Not Applicable Stress Intensity Pure Shear Stress              0.6Sm                          0.42Su Peak                  Per Section 2.1.2.2.2, Fatigue Assessment Buckling              Per Section 2.1.2.2.3, Buckling Assessment Table 2.1 Non-Containment Structure Allowable Stress Limits Stress Category                  NCT                          HAC General Primary Membrane    Greater of:      Sm                  0.7Su Stress Intensity                        Sy Local Primary Membrane    Greater of:  1.5Sm                      Su Stress Intensity                        Sy Primary Membrane + Bending    Greater of:  1.5Sm                      Su Stress Intensity                        Sy Range of Primary + Secondary  Greater of:  3.0Sm              Not Applicable Stress Intensity                        Sy Pure Shear Stress      Greater of:  0.6Sm                  0.42Su 0.6Sy Peak                  Per Section 2.1.2.2.2, Fatigue Assessment Buckling              Per Section 2.1.2.2.3, Buckling Assessment 2.1-7
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.1-8
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 2.2 Weights and Centers of Gravity The maximum gross weight of the HalfPACT package, including a maximum payload weight of 7,600 pounds, is 18,100 pounds. The vertical center of gravity (CG) is situated 43.5 inches above the bottom surface of the package. These values are used in the lifting and tie-down calculations presented in Section 2.5, Lifting and Tie-down Standards for All Packages. These results are based on an assumption of a payload configuration consisting of seven, 1,000 pound, 55-gallon drums having their individual CGs located at the drum mid-height. All other payload configurations result in a lower, package gross weight and CG than the 55-gallon drum payload configuration. With reference to Figure 2.2-1, a detailed breakdown of the HalfPACT package component weights and CG is summarized in Table 2.2-1. The five-inch thick payload spacer is used with the 55-gallon drum, short 85-gallon drum, 100-gallon drum, and standard waste box (SWB) payload configurations. The SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2 shielded containers utilize a specialized payload pallet and specific radial, lateral, and/or axial dunnage configurations in lieu of the payload pallet and payload spacer utilized for drums and the SWB. The SC-30G1 payload configuration utilizes a triangular payload pallet, an upper and lower axial dunnage assembly, and a radial dunnage assembly. The SC-30G2 payload configuration utilizes a heavy-duty payload pallet, radial dunnage assembly, and axial dunnage assembly. The SC-30G3 and SC-55G2 payload configurations utilize a heavy-duty payload pallet and a lateral dunnage assembly. The SC-55G1 payload configuration utilizes a heavy-duty payload pallet and radial dunnage assembly.
2.2.1      Effect of a Radial Payload Imbalance A radial offset of the CG could occur if the payload drums do not all have the same weight, or if the SWB is not uniformly loaded. The maximum offset of the radial CG is calculated in the following paragraphs.
Seven 55-Gallon Drum Payload Configuration:
Since the maximum weight of any one drum is 1,000 pounds, and since the arrangement of seven drums is symmetric, the maximum payload weight can be associated only with a payload CG located on the package centerline. Deviation from the package centerline can only occur with a less-than-maximum total payload weight. The worst case CG offset occurs for an arrangement of four minimum weight (empty) 55-gallon drums, each having a weight of approximately 60 pounds, together with three maximum weight (fully loaded) 55-gallon drums, each having a weight of 1,000 pounds, located in adjacent outside positions, as illustrated in Figure 2.2-2. A 55-gallon drum has a nominal outer diameter of 24 inches. For this case, the worst case radial location of the payload CG is:
(24.00)(1,000) + 2(12.00)(1,000) + (0)(60)  2(12.00)(60)  (24.00)(60) r    = 13.93 inches 3(1,000) + 4(60)
The pipe overpack and criticality control overpack payload configurations, since they are enclosed and centered by dunnage within a 55-gallon drum, are enveloped by the foregoing considerations. For an empty package weight of 10,500 pounds, a payload pallet weight of 350 pounds, and a payload spacer weight of 250 pounds, (see Table 2.2-1), the worst case radial offset of the CG of the entire HalfPACT package is:
2.2-1
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 (13.93)[3(1,000) + 4(60)]
R=                                            = 3.15 inches 10,500 + 350 + 250 + 3(1,000) + 4(60)
This radial offset equates to only 3.3% of the HalfPACT packages outer diameter of 94 inches. The effect of this relatively small radial offset may be neglected.
One Standard Waste Box Payload Configuration:
The maximum weight of a loaded SWB is 4,000 pounds; the weight of an empty SWB is approximately 640 pounds. The maximum contents therefore amount to approximately 4,000 - 640 = 3,360 pounds. The CG of the contents is conservatively assumed to be located at a distance of 17.75 inches from the geometric center (i.e., one-quarter the SWB length), as shown in Figure 2.2-3. For this case, the worst case radial location of the payload CG is:
(17.75)(3,360) r=                  = 14.9 inches 4,000 For an empty package weight of 10,500 pounds and a payload spacer weight of 250 pounds, (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(14.9)(4,000)
R=                          = 4.04 inches 10,500 + 250 + 4,000 This radial offset equates to only 4.3% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
Four 85-Gallon Drum Payload Configuration:
The term 85-gallon drum refers to drums of 75 to 88 gallons, as discussed in Section 1.1, Introduction. As for the 55-gallon drum payload configuration, the maximum weight of a loaded 85-gallon drum is 1,000 pounds. The worst case CG offset occurs for an arrangement of two minimum weight (empty), tall 85-gallon drums, each having a weight of approximately 81 pounds, together with two maximum weight (fully loaded), tall 85-gallon drums, each having a weight of 1,000 pounds, located adjacent, as illustrated in Figure 2.2-4. A tall 85-gallon drum has a nominal outer diameter of 28 inches. For this case, the worst case radial location of the payload CG is:
2(14.31)(1,000)  2(14.31)(81) r=                                    = 12.2 inches 2(1,000) + 2(81)
For an empty package weight of 10,500 pounds, a payload pallet weight of 350 pounds, and a payload spacer weight of 250 pounds, (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(12.2)[2(1,000) + 2(81)]
R=                                      = 2.03 inches 10,500 + 350 + 2(1,000) + 2(81)
This radial offset equates to only 2.1% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
2.2-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 Three 100-Gallon Drum Payload Configuration:
As for the 55-gallon drum payload configuration, the maximum weight of a loaded 100-gallon drum is 1,000 pounds. The worst case CG offset occurs for an arrangement of two minimum weight (empty), 100-gallon drums, each having a weight of approximately 95 pounds, together with one maximum weight (fully loaded), 100-gallon drum of 1,000 pounds, as illustrated in Figure 2.2-5. A 100-gallon drum has a nominal outer diameter of 32 inches. For this case, the worst case radial location of the payload CG is:
(18.48)(1,000)  2(9.24)(95) r=                                = 14.1 inches 1,000 + 2(95)
For an empty package weight of 10,500 pounds, a payload pallet weight of 350 pounds, and a payload spacer weight of 250 pounds, (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(14.1)[1,000 + 2(95)]
R=                                      = 1.37 inches 10,500 + 350 + 250 + 1,000 + 2(95)
This radial offset equates to only 1.5% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
Three SC-30G1 Shielded Container Payload Configuration:
The maximum weight of a loaded SC-30G1 is 2,260 pounds; the weight of an empty SC-30G1 is approximately 1,726 pounds. The worst case CG offset occurs for an arrangement of two minimum weight (empty), SC-30G1s, each having a weight of approximately 1,726 pounds, together with one maximum weight (fully loaded), SC-30G1 of 2,260 pounds, as illustrated in Figure 2.2-6. An SC-30G1 has a nominal outer diameter of 23 inches. For this case, the worst case radial location of the payload CG is:
(13.28)(2,260)  2(6.64)(1,726) r=                                    = 1.24 inches 2,260 + 2(1,726)
For an empty package weight of 10,500 pounds, a triangular payload pallet weight of 112 pounds, an upper and lower axial dunnage weight of 132 pounds each, and a radial dunnage weight of 444 pounds, (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(1.24)[2,260 + 2(1,726)]
R=                                                    = 0.42 inches 10,500 + 112 + 2(132) + 444 + 2,260 + 2(1,726)
This radial offset equates to only 0.4% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
Two SC-30G2 Shielded Container Payload Configuration:
The worst case CG offset occurs for an arrangement of one minimum weight (empty) SC-30G2 having a weight of approximately 2,610 pounds, together with one maximum weight (fully loaded) SC-30G2 having a weight of 3,160 pounds, located adjacent, as illustrated in Figure 2.2-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 2.2-7. An SC-30G2 has a nominal outer diameter of 24.5 inches. For this case, the worst case radial location of the payload CG is:
(12.25)(3,160)  (12.25)(2,610)
=r                            = 1.17 inches 3,160 + 2,610 For an empty package weight of 10,500 pounds, a heavy-duty payload pallet weight of 200 pounds, an axial dunnage weight of 336 pounds, and a radial dunnage weight of 744 pounds, (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(1.17)(3,160 + 2,610)
R    = 0.38 inches 10,500 + 200 + 336 + 744 + 3,160 + 2,610 This radial offset equates to only 0.4% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
One SC-30G3 Shielded Container Payload Configuration:
The maximum weight of a loaded SC-30G3 is 6,300 pounds; the weight of an empty SC-30G3 is approximately 5,750 pounds. The maximum contents therefore amount to 6,300 - 5,750 =
550 pounds, approximately. The CG of the contents is conservatively assumed to be located at a distance of 10.57 inches from the geometric center (i.e., one-quarter the SC-30G3 length), as shown in Figure 2.2-8. For this case, the worst case radial location of the payload CG is:
(10.57)(550)
                        =          r    = 0.92 inches 6,300 For an empty package weight of 10,500 pounds, a heavy-duty payload pallet weight of 200 pounds, and a lateral dunnage weight of 1,100 pounds (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(0.92)(6,300)
=                          R    = 0.32 inches 10,500 + 200 + 1,100 + 6,300 This radial offset equates to only 0.3% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
Two SC-55G1 Shielded Container Payload Configuration:
The worst case CG offset occurs for an arrangement of one minimum weight (empty) SC-55G1 having a weight of approximately 2,810 pounds, together with one maximum weight (fully loaded) SC-55G1 having a weight of 3,410 pounds, located adjacent, as illustrated in Figure 2.2-9. An SC-55G1 has a nominal outer diameter of 29.4 inches. For this case, the worst case radial location of the payload CG is:
(14.7)(3,410)  (14.7)(2,810)
=                          r    = 1.42 inches 3,410 + 2,810 2.2-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 For an empty package weight of 10,500 pounds, a heavy-duty payload pallet weight of 200 pounds, and a radial dunnage weight of 580 pounds, (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(1.42)(3,410 + 2,810)
=                        R    = 0.50 inches 10,500 + 200 + 580 + 3,410 + 2,810 This radial offset equates to only 0.5% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
One SC-55G2 Shielded Container Payload Configuration:
The maximum weight of a loaded SC-55G2 is 6,500 pounds; the weight of an empty SC-55G2 is approximately 5,900 pounds. The maximum contents therefore amount to 6,500 - 5,900
= 600 pounds, approximately. The CG of the contents is conservatively assumed to be located at a distance of 11.44 inches from the geometric center (i.e., one-quarter the SC-55G2 length), as shown in Figure 2.2-10. For this case, the worst case radial location of the payload CG is:
(11.44)(600)
                        =          r    = 1.06 inches 6,500 For an empty package weight of 10,500 pounds, a heavy-duty payload pallet weight of 200 pounds, and a lateral dunnage weight of 900 pounds (see Table 2.2-1), the maximum radial offset of the CG of the entire HalfPACT is:
(1.06)(6,500)
  =                        R    = 0.38 inches 10,500 + 200 + 900 + 6,500 This radial offset equates to only 0.4% of the HalfPACT packages outer diameter of 94 inches. As before, the effect of this relatively small radial offset may be neglected.
2.2.2      Effect of an Axial Payload Imbalance The maximum height of the package CG is associated with a uniformly loaded payload, where the CG of the payload containers is located at their mid-height. Due to a payload of non-uniform density or possible settling of the payload contents, the CG height of the payload containers may decrease somewhat. The seven 55-gallon drum payload configuration, since it is the heaviest payload, will result in greatest potential shift in axial CG. The greatest shift in location of the CG of an individual drum is bounded by one-quarter of the drum height, i.e., a shift from the drum mid-height to the quarter height. Thus, for a total 55-gallon drum height of 35 inches, the axial shift is 35/4 = 8.75 inches downward. Since the empty weight of a 55-gallon drum is approximately 60 pounds, the maximum weight of contents of one drum is approximately 1,000 - 60 = 940 pounds. The greatest downward shift in CG location of the HalfPACT packaging, assuming the CG location of all seven drums is at one quarter of the drum height instead of at mid-height, therefore is:
7(8.75)(940) h =                = 3.2 inches 18,100 2.2-5
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 The axial offset amounts to only 3.5% of the total HalfPACT package height of 911/2 inches. The effect of this relatively small axial offset may be neglected. As an example, in the case of a hypothetical accident condition (HAC) puncture event where the puncture bar axis passes through the CG of the HalfPACT package, the variation in CG location of 3.2 inches slightly exceeds half the puncture bar diameter resulting in a variation of the puncture bar orientation of less than 4 degrees. In addition, vertical reduction of the CG would have no effect on lifting forces, and would serve to reduce tie-down forces. Therefore, the lifting and tie-down calculations, and the HAC free drop and puncture tests, are performed using a value that bounds the maximum CG height presented in Table 2.2-1, and the downward axial offset is conservatively neglected.
2.2-6
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 2.2 HalfPACT Weight and Center of Gravity Weight, pounds    Height to CG, inches Item              Component  Assembly Component    Assembly Outer Confinement Assembly (OCA)                8,250                41.2
* Lid                              3,600                67.1
* Body                              4,650                21.2 Inner Containment Vessel (ICV)                  2,250                47.3
* Lid                                825                66.5
* Body                              1,225                34.9
* Aluminum Honeycomb Spacers          200                43.5 Total Empty Package                            10,500                42.5 Payload and Payload Components                  7,600                45.5
* Payload (Seven 55-Gallon Drums)  7,000                46.6
* Payload Pallet                      350                27.7
* Payload Spacer                      250                23.6 Total Loaded Package (Maximum)                  18,100                43.5 Payload and Payload Components                  7,600                44.2
* Payload (Three SC-30G1s)          6,780                44.5
* Triangular Payload Pallet          112                25.1
* Axial Dunnage Assemblies            264                43.0
* Radial Dunnage Assembly            444                44.5 Total Load Package (Maximum)                    18,100                43.2 Payload and Payload Components                  7,600                43.0
* Payload (Two SC-30G2s)            6,320                42.5
* Heavy-Duty Payload Pallet          200                22.9
* Axial Dunnage Assemblies            336                63.1
* Radial Dunnage Assembly            744                43.3 Total Load Package (Maximum)                    18,100                42.7 Payload and Payload Components                  7,600                44.0
* Payload (One SC-30G3)            6,300                44.6
* Heavy-Duty Payload Pallet          200                22.9
* Lateral Dunnage Assembly          1,100                44.6 Total Load Package (Maximum)                    18,100                43.1 2.2-7
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Weight, pounds    Height to CG, inches Item                    Component  Assembly Component    Assembly Payload and Payload Components                        7,600                44.2
* Payload (Two SC-55G1s)                6,820                44.5
* Heavy-Duty Payload Pallet                200                22.9
* Radial Dunnage Assembly                  580                48.4 Total Load Package (Maximum)                          18,100                43.2 Payload and Payload Components                        7,600                44.0
* Payload (One SC-55G2)                  6,500                44.6
* Heavy-Duty Payload Pallet                200                22.9
* Lateral Dunnage Assembly                900                44.6 Total Load Package (Maximum)                          18,100                43.1 Note:
The reference datum is the bottom of the HalfPACT package.
2.2-8
 
HalfPACT Safety Analysis Report            Rev. 9, August 2022 Figure 2.2 HalfPACT Package Components 2.2-9
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Figure 2.2 Radial Shift of CG for Seven 55-Gallon Drum Payload 2.2-10
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.2 Radial Shift of CG for One SWB Payload 2.2-11
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Figure 2.2 Radial Shift of CG for Four 85-Gallon Drum Payload 2.2-12
 
HalfPACT Safety Analysis Report                          Rev. 9, August 2022 Figure 2.2 Radial Shift of CG for Three 100-Gallon Drum Payload 2.2-13
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Figure 2.2 Radial Shift of CG for Three SC-30G1 Shielded Container Payload 2.2-14
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022
                                                +X 12.25 12.25 2,610 LB              3,160 LB 24.5 Figure 2.2 Radial Shift of CG for Two SC-30G2 Shielded Container Payload 2.2-15
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022
                                            +X 10.57
                                                        Ø 28 5,750 LB  550 LB 42.26 Figure 2.2 Radial Shift of CG for One SC-30G3 Shielded Container Payload 2.2-16
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022
                                              +X 14.7 14.7 2,810 LB              3,410 LB 29.4 Figure 2.2 Radial Shift of CG for Two SC-55G1 Shielded Container Payload 2.2-17
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022
                                          +X 11.44
                                                      Ø 31 5,900 LB  600 LB 45.75 Figure 2.2 Radial Shift of CG for One SC-55G2 Shielded Container Payload 2.2-18
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 2.3 Mechanical Properties of Materials The major structural components, i.e., the outer confinement assembly (OCA) outer shells, outer confinement vessel (OCV), and inner containment vessel (ICV), of the HalfPACT packaging are fabricated of Type 304, austenitic stainless steel and 8 lb/ft3 (nominal density) polyurethane foam. Other materials performing a structural function are ASTM B16 brass (for the ICV and OCV vent port and seal test port plugs and covers), aluminum honeycomb (for the ICV aluminum honeycomb spacer assemblies), 300 series stainless steel (for the ICV and OCV locking ring lock bolts, and for attaching the locking Z-flange to the OCV locking ring), and ASTM A564, Type 630, stainless steel (joint pins for the OCV and ICV locking rings). Several varieties of non-structural materials are also utilized. Representative non-structural materials include butyl rubber and other elastomeric O-ring seals, a silicone wear pad, aluminum guide tubes for the OCA lid lift operation, ceramic fiber paper, fiberglass insulation, and plastic fire consumable foam cavity vent plugs. The drawings presented in Appendix 1.3.1, Packaging General Arrangement Drawings, delineate the specific material(s) used for each HalfPACT packaging component.
The remainder of this section presents and discusses pertinent mechanical properties for the materials that perform a structural function. Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, presents all properties used in analytic structural evaluations of the HalfPACT package. Most normal conditions of transport (NCT) tests are demonstrated analytically. Section 2.3.2, Mechanical Properties Applied to Certification Testing, presents the mechanical properties associated with components whose performance is demonstrated via certification testing. With the exception of immersion, all hypothetical accident condition (HAC) tests are demonstrated via certification testing.
2.3.1      Mechanical Properties Applied to Analytic Evaluations Analytic evaluations are performed for the basic OCA, OCV, and ICV shells, seal flanges, and locking rings, comprised of Type 304 stainless steel. Table 2.3-1 presents the mechanical properties for the Type 304 stainless steel used in the HalfPACT packaging. Each of the mechanical properties of Type 304 stainless steel is taken from Section II, Parts A and D, of the ASME Boiler and Pressure Vessel Code. 1 All analyses of the basic OCA, OCV, and ICV shells, seal flanges and locking rings utilize the properties presented for ASTM A240, Type 304, stainless steel. With the exception of elongation, which is not specifically used in the linear elastic analytic assessments, all materials presented in Table 2.3-1 exhibit equivalent or better properties than the ASTM A240 material.
Minimum elongation values are important regarding testing and are therefore discussed in Section 2.3.2, Mechanical Properties Applied to Certification Testing. The density of stainless steel is taken as 0.29 lb/in3, and Poissons Ratio is 0.3.
Unlike the other ASTM materials specified in Table 2.3-1, ASTM A276 material does not have an identical ASME material specification. However, structural use of ASTM A276 is as an option for the OCA rolled angles used at the lid-to-body interface and the OCA lid lifting straps.
1 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section II, Materials, Part A - Ferrous Material Specifications, and Materials, Part D - Properties, 1995 Edition, 1997 Addenda.
2.3-1
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 As these components are not part of the containment boundary, the use of ASTM A276, whose chemical and mechanical properties are identical to ASTM A479, is justified. Thus, material properties of ASTM A276 versus temperature are taken to be the same as for ASTM A479.
The analytic assessments of the polyurethane foam used in the HalfPACT packaging are limited to the NCT internal pressure, differential thermal expansion, and lifting load cases. The data summarized in Table 2.3-2 are established according to the procedures outlined in Section 8.1.4.1, Polyurethane Foam. Detailed stress-strain relationships for the polyurethane foam are not required for analysis since analytic assessments for the NCT or HAC free drop or puncture events are not performed. However, as discussed in Section 2.3.2, Mechanical Properties Applied to Certification Testing, since HalfPACT package performance is demonstrated by certification testing, and performance is a function of foam properties, compressive stress-strain characteristics and installation techniques are carefully controlled.
Material properties are linearly interpolated between, or, if necessary, extrapolated beyond the temperature values shown. For example, when a temperature outside a tabulated range is of interest (e.g., low temperature properties to -40 °F), data are extrapolated. When a particular analysis requires data extrapolation, it is identified within the applicable section of this chapter.
2.3.2      Mechanical Properties Applied to Certification Testing The primary means of demonstrating the structural performance capabilities of the HalfPACT packaging under imposed NCT and HAC free drops, puncture, and thermal (fire) events is via certification testing. The overall response of the HalfPACT packaging to these events is dependent on the characteristics of several structural components. The characteristics of the polyurethane foam used in the OCA are of primary importance regarding HalfPACT package performance. For this reason, the method of installation of the foam material into the OCA, and the foams compressive stress-strain characteristics are carefully controlled and monitored.
Section 8.1.4.1, Polyurethane Foam, presents the details associated with foam installation and performance testing. Importantly, all HalfPACT packages will respond similarly to free drop, puncture, and thermal events. Thermal performance of the foam is discussed in Section 3.2, Summary of Thermal Properties of Materials.
At the time of polyurethane foam installation, test samples are retained from each foam pour, as discussed in Section 8.1.4.1, Polyurethane Foam. Using these samples, each foam pour is tested for compressive strength at strains of 10%, 40%, and 70%, both parallel and perpendicular to the direction of foam rise. To be acceptable, the average compressive strength of all tested samples from a single foamed component (i.e., the OCA lid or OCA body) for a particular rise direction is to fall within +/-15% of the corresponding nominal compressive stress. Additionally, the stress value of any single test specimen from a single pour is to fall within +/-20% of the corresponding nominal compressive stress.
In addition to controls on foam compressive stress, OCA foam thicknesses are controlled by the tolerances shown on the drawings provided in Appendix 1.3.1, Packaging General Arrangement Drawings. The foam thickness tolerance at the OCA top and sides is set at approximately +/-5% of the nominal thickness. In regions where foam strains are very small (e.g., bottom end), a slightly greater thickness tolerance (approximately +/-8%) is allowed. The thickness tolerance is set at approximately one-third the magnitude of the compressive stress tolerance to minimize the effect on package performance in the unlikely event that both tolerances are simultaneously at their 2.3-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 extreme values in a given HalfPACT packaging assembly. Importantly, in the unlikely event that compressive stress and thickness tolerances are simultaneously at their worst case extremes, the net effect of combining the two tolerances is nearly identical to the compressive stress tolerance acting alone. This is directly attributable to the fact that a long portion of the compressive stress-strain curve for foam (at strains of ~50% or less) exhibits a relatively shallow slope (i.e., plateau).
Consequently, although small changes in foam thickness directly affect foam strains, small changes in strain while on the plateau portion of the stress-strain curve do not significantly affect stress. As demonstrated by testing (documented in Appendix 2.10.3, Certification Tests), the HalfPACT packaging deformations due to 30-foot free drops were relatively small, demonstrating that resultant foam strains remained within the plateau portion of the compressive stress-strain curve.
In addition to the polyurethane foam, the performance of other primary HalfPACT packaging structural components is addressed by certification testing rather than by analysis. These components include the ASTM B16, Alloy 360, half-hard temper, brass vent port plugs, the ICV upper and lower aluminum honeycomb spacer assemblies, the 300 series stainless steel socket head cap screws used to secure the locking rings in the locked position, the ASTM A564, Type 630, Condition 1150, stainless steel pins used in the locking ring joints, and the 1/4-inch, 300 series stainless steel pan head screws used to attach the locking Z-flange to the OCV locking ring. As indicated above, and on the drawings provided in Appendix 1.3.1, Packaging General Arrangement Drawings, each of these components has a specific material callout thereby providing a specific control on its mechanical properties. The structurally significant mechanical properties for these materials are presented in Table 2.3-3.
With the exception of the aluminum honeycomb spacer assemblies, the 1/4-inch stainless steel pan head screws, and the OCV lock bolts, all of the above components remained intact during certification testing, and showed essentially no evidence of distress. By design, the aluminum honeycomb spacer assemblies were partially crushed as a result of the certification test program, but still provided adequate protection for the ICV torispherical heads from the simulated payload of seven, rigid, concrete-filled, 55-gallon drums.
The optional use of Type 304 stainless steel forgings or castings instead of ASTM A240 plate material for the OCV and ICV seal flanges and locking rings is stated on the drawings provided in Appendix 1.3.1, Packaging General Arrangement Drawings. As shown in Table 2.3-1, the ASTM A182 forging option and ASTM A351 casting option provide equivalent or improved strength, but a somewhat reduced elongation than does the ASTM A240. The reduced elongation values (30% for ASTM A182 and 35% for ASTM A351 versus 40% for ASTM A240 material) are acceptable based on the results of the certification testing program. Relatively little permanent deformation was observed for the OCV or ICV seal flanges and locking rings as a result of certification testing, indicating that strains were well below the 30% minimum elongation provided by any of the specified materials. Any of the three material options are therefore acceptable for fabricating HalfPACT packagings.
2.3-3
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.3-4
 
HalfPACT Safety Analysis Report                                                                          Rev. 9, August 2022 Table 2.3 Mechanical Properties of Type 304 Stainless Steel Components (for Analysis)
Thermal Minimum                          Yield        Ultimate    Allowable        Elastic        Expansion Material      Elongation      Temperature Strength, Sy Strength, Su Strength, Sm        Modulus, E Coefficient, Specification          (%)            (°F)        (x103 psi)    (x103 psi)  (x103 psi)      (x106 psi) (x10-6 in/in/°F)
ASTM A213              35            -20          30.0          75.0          20.0          28.8            8.21 ASTM A240              40              70          30.0          75.0          20.0            28.3            -----
ASTM A312              30            100            30.0          75.0          20.0            -----            8.55 ASTM A376              25            200            25.0          71.0          20.0            27.6            8.79 ASTM A479              30            300            22.5          66.0          20.0            27.0            9.00 Type 304                            400            20.7          64.4          18.7            26.5            9.19
                                        -20          30.0          75.0          20.0          28.8            8.21 70          30.0          75.0          20.0            28.3            -----
ASTM A182 100            30.0          75.0          20.0            -----            8.55 Type F304            30 200            25.0          71.0          20.0            27.6            8.79
(<5 inch thick) 300            22.5          66.0          20.0            27.0            9.00 400            20.7          64.4          18.7            26.5            9.19
                                        -20          35.0          77.0          23.3          28.8            8.21 70          35.0          77.0          23.3            28.3            -----
ASTM A351                            100            35.0          77.0          23.3            -----            8.55 35 Grade CF8A                            200            29.1          72.8          23.3            27.6            8.79 300            26.3          67.8          22.6            27.0            9.00 400            24.2          66.1          21.8            26.5            9.19 Notes:  ASME Code, Section II, Part A.                  ASME Code, Section II, Part D, Table 2A.
ASME Code, Section II, Part D, Table Y-1.      ASME Code, Section II, Part D, Table TM-1, Material Group G.
ASME Code, Section II, Part D, Table U.        ASME Code, Section II, Part D, Table TE-1, 18Cr-8Ni, Coefficient B.
Interpolated/extrapolated 2.3-5
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 This page intentionally left blank.
2.3-6
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Table 2.3 Mechanical Properties of Polyurethane Foam (for Analysis)
Nominal Room Property                          Direction              Temperature Value Compressive Strength, S            Axial (Parallel-to-Rise)              235 psi Radial (Perpendicular-to-Rise)            195 psi Compressive Modulus, E              Axial (Parallel-to-Rise)            6,810 psi Radial (Perpendicular-to-Rise)          4,773 psi Thermal Expansion Coefficient,                    -----                3.5 x 10-5 in/in/&#xba;F Poissons Ratio,                          -----                        0.33 Density,                              -----                      8.25 lb/ft3 Table 2.3 Mechanical Properties of Metallic Materials (for Testing)
Minimum Mechanical Properties Material                      (unless otherwise specified)                  Notes ASTM B16, Alloy 360 Brass,                          y = 25,000 psi Half-Hard Temper                                    u = 55,000 psi Hexcel ACG-3/8-.003-3.6P          bc = 340 psi +/-15% (Bare Compressive Strength)
Aluminum Honeycomb                        c = 120 psi +/-15% (Crush Strength) 300 Series Stainless Steel                          y = 40,000 psi Socket Head Cap Screws                              u = 80,000 psi ASTM A564, Type 630,                              y = 105,000 psi Condition 1150, Stainless Steel                    u = 135,000 psi 1/4-inch, 300 Series Stainless                      y = 30,000 psi Steel Pan Head Screws u = 75,000 psi Notes:
Mechanical Properties of Hexcel Honeycomb Materials, TSB-120 (Technical Service Bulletin 120), Hexcel, 1992. The term Bare Compressive Strength is defined as the maximum strength that is exhibited by the honeycomb material at the onset of crushing. The term Crush Strength is defined as the average compressive strength that is sustained as the honeycomb material undergoes crushing.
UNBRAKO Socket Screw Products Catalog, Copyright 1988, SPS Technologies.
ASME Code, Section II, Part D, Table 2A, 1995 Edition, 1997 Addenda.
Industrial Fasteners Institute, Fastener Standard, Fifth Edition.
2.3-7
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.3-8
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 2.4 General Standards for All Packages This section defines the general standards for all packages. The HalfPACT package, with an outer confinement vessel (OCV) that is integral to an outer confinement assembly (OCA), and an inner containment vessel (ICV) for primary containment, meets all requirements delineated for this section.
2.4.1        Minimum Package Size The minimum transverse dimension (i.e., the diameter) of the HalfPACT package is 94 inches, and the minimum longitudinal dimension (i.e., the height) is 911/2 inches. Thus, the requirement of 10 CFR &sect;71.43(a) 1 is satisfied.
2.4.2        Tamper-indicating Feature Tamper-indicating seals are installed at one OCA lock bolt location and at the OCV vent port access plug, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. A lock wire device is used between two tie-points. For the OCV lock bolt, the tie-points are the bolt head and the locking Z-flange. The two tie-points for the OCV vent port access plug are the plug itself and a bolt tapped and welded to the OCA body outer shell. Failure of either tamper-indicating device provides evidence of possible unauthorized access. Thus, the requirement of 10 CFR &sect;71.43(b) is satisfied.
2.4.3        Positive Closure The HalfPACT package cannot be opened unintentionally. Both the OCA and ICV lids are attached to their respective bodies with locking rings. The OCV locking ring is secured with six, 1/2-13UNC, OCA lock bolts through the attached locking Z-flange. Similarly, the ICV locking ring is secured in the locked position with three, 1/2-13UNC, ICV lock bolts. For either lid, the presence of a single, lock bolt will prevent lid removal.
The OCV vent port has three levels of protection against inadvertent opening: 1) the OCV vent port access plug, 2) the OCV vent port cover, and 3) the OCV vent port plug. Each of these components are secured via threaded fittings. The ICV vent port has two levels of protection against inadvertent opening: 1) the ICV vent port cover, and 2) the ICV vent port plug. Thus, the requirements of 10 CFR &sect;71.43(c) are satisfied.
2.4.4        Chemical and Galvanic Reactions The major materials of construction of the HalfPACT packaging (i.e., austenitic stainless steel, aluminum, brass, polyurethane foam, ceramic fiber paper, fiberglass insulation, butyl rubber O-ring seals and other elastomeric materials) will not have significant chemical, galvanic or other reactions in air, inert gas or water environments, thereby satisfying the requirements of 10 CFR &sect;71.43(d). These materials have been previously used, without incident, in radioactive material (RAM) packages for transport of similar payload materials. Specifically, these 1
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2.4-1
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 materials of construction have been used in the TRUPACT-II package 2 for many years without incident, utilizing the same materials of construction and carrying identical payloads as will be carried in the HalfPACT package. A successful RAM packaging history combined with successful use of these fabrication materials in similar industrial environments ensures that the integrity of the HalfPACT package will not be compromised by any chemical, galvanic or other reactions. The materials of construction and the payload are further evaluated below for potential reactions.
2.4.4.1        Packaging Materials of Construction The HalfPACT packaging is primarily constructed of Type 304 stainless steel. This material is highly corrosion resistant to most environments. The metallic structure of the HalfPACT packaging is composed entirely of this material and compatible 300 series weld material. The weld material and processes have been selected in accordance with the ASME Boiler and Pressure Vessel Code 3 to provide as good or better material properties, including corrosion resistance, as the base material.
Since both the base and weld materials are 300 series materials, they have nearly identical electrochemical potential thereby minimizing any galvanic corrosion that could occur.
The stainless steel within the OCA foam cavity is lined with a ceramic fiber paper, composed of alumina silica. This material is nonreactive with either the polyurethane foam or the stainless steel, both dry or in water. The ceramic fiber paper and the silicone adhesive are very low in free chlorides to minimize the potential for stress corrosion of the OCA structure.
The polyurethane foam that is used in the OCA is essentially identical to previously licensed transportation packagings, such as the TRUPACT-II (Docket 71-9218), NuPac 125B (Docket 71-9200), and NuPac PAS-1 (Docket 71-9184). All of these packagings have had a long and successful record of performance demonstrating that the polyurethane foam does not cause any adverse conditions with the packaging. The polyurethane foam in the OCA is a rigid, closed-cell (non-water absorbent) foam that is very low in free halogens and chlorides, as discussed in Section 8.1.4.1, Polyurethane Foam. The polyurethane foam material cavity is sealed with plastic pipe plugs to preclude the entrance of moisture.
Aluminum honeycomb is used in the HalfPACT packaging for the two, ICV aluminum honeycomb spacer assemblies in the upper and lower ICV torispherical heads. Aluminum honeycomb material is used for dunnage only, and is not used as any part of the HalfPACT packagings containment boundary. The aluminum honeycomb is maintained at relatively low temperatures ensuring that no adverse reaction could occur at aluminum/steel interfaces that would compromise the packagings containment integrity. Of final note, aluminum material is slightly anodic which serves to protect the stainless steel of the ICV.
The various brass fittings and plugs used in the HalfPACT packaging are very corrosion resistant. Like aluminum, brass material is slightly anodic to the stainless steel. Any damage that could occur to the brass is easily detectable since the fittings are all handled each time the HalfPACT package is loaded and unloaded.
2 U.S. Department of Energy (DOE), Safety Analysis Report for the TRUPACT-II Shipping Package, USNRC Certificate of Compliance 71-9218, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
3 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, 1995 Edition, 1997 Addenda.
2.4-2
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 The various elastomers (e.g., butyl rubber, polyester, silicone, etc.) that are used in the O-rings, annulus foam ring, debris shield, wear pad, etc., contain no corrosives that would react adversely affect the HalfPACT packaging. These materials are organic in nature and noncorrosive to the stainless steel containment boundary of the HalfPACT packaging.
2.4.4.2      Payload Interaction with Packaging Materials of Construction The materials of construction of the HalfPACT packaging are checked for compatibility with the various payload chemistries when the payloads are evaluated for chemical compatibility. All payload materials are in approved payload containers delineated in the CH-TRAMPAC 4.
The payload is typically further confined within multiple layers of plastic for radiological health purposes. This configuration ensures that the payload material has an insignificant level of contact with the HalfPACT packaging materials of construction. However, the evaluation of compatibility is based on complete interaction of payload materials with the packaging.
The design of the HalfPACT package is for transport of CH-TRU materials and other authorized payloads that are limited in form to solid or solidified material. Corrosive materials, pressurized containers, explosives, non-radioactive pyrophorics, and liquid volumes greater than 1% are prohibited. These restrictions ensure that the waste in the payload is in a non-reactive form for safe transport in the HalfPACT package. For a comprehensive discussion defining acceptable payload properties, see the CH-TRAMPAC.
2.4.5      Valves Neither the OCV nor the ICV have valves. However, beside their respective lids, the ICV and the OCV each have a vent port penetration into their containment and confinement cavities, respectively. These vent port penetrations are sealed using threaded vent port plugs comprised of brass material. Since the ICV is entirely contained within the OCV during transport, a tamper indicating device is not necessary. Access to the OCV vent port penetration is prevented by a lockwire that secures the OCV vent port access plug, as discussed in Section 2.4.2, Tamper-indicating Feature. Thus, the requirements of 10 CFR &sect;71.43(e) are satisfied.
2.4.6      Package Design As shown in Chapter 2.0, Structural Evaluation, Chapter 3.0, Thermal Evaluation, Chapter 5.0, Shielding Evaluation, and Chapter 6.0, Criticality Evaluation, the structural, thermal, shielding, and criticality requirements, respectively, of 10 CFR &sect;71.43(f) are satisfied for the HalfPACT package.
2.4.7      External Temperatures As shown in Table 3.5-1 from Section 3.5.3, Package Temperatures, the maximum accessible surface temperature with maximum internal decay heat load and no insolation is 102 &#xba;F. Since the maximum external temperature does not exceed 185 &#xba;F, the requirements of 10 CFR
&sect;71.43(g) are satisfied.
4 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
2.4-3
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 2.4.8    Venting The HalfPACT package does not include any features intended to allow continuous venting during transport. Thus, the requirements of 10 CFR &sect;71.43(h) are satisfied.
2.4-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 2.5 Lifting and Tie-down Standards for All Packages For analysis of the lifting and tie-down components of the HalfPACT packaging, material properties from Section 2.3, Mechanical Properties of Materials, are taken at a bounding temperature of 160 &deg;F per Section 2.6.1.1, Summary of Pressures and Temperatures. The primary structural materials are Type 304 stainless steel, and polyurethane foam that is used in the outer confinement assembly (OCA).
A loaded HalfPACT package is only lifted by fork lift pockets, located at the bottom of the OCA body. For this case, HalfPACT package lifting loads act parallel to the direction of foam rise.
The nominal compressive strength of the polyurethane foam, as delineated in Table 2.3-2 of Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, is reduced by 15% to account for manufacturing tolerance; polyurethane foam manufacturing tolerances are discussed in Section 8.1.4.1.2.3.2, Parallel-to-Rise Compressive Stress. The nominal compressive strength of the polyurethane foam is further reduced by 25% to account for elevated temperature effects, as discussed in Section 2.6.1.1, Summary of Pressures and Temperatures.
Properties of Type 304 stainless steel and polyurethane foam, parallel to the direction of foam rise accounting for manufacturing tolerances and elevated temperature, are summarized below.
Material Property                              Value                Reference Type 304 Stainless Steel at 160 &#xba;F Elastic Modulus, E                        27.8 x 106 psi Yield Strength, y                        27,000 psi              Table 2.3-1 Shear Stress, equal to (0.6)y                  16,200 psi Polyurethane Foam (parallel-to-rise) at 160 &#xba;F Minimum compressive strength, c                    150 psi Table 2.3-2 Bearing stress, assumed equal to (2/3)c                100 psi 2.5.1      Lifting Devices This section demonstrates that the fork lift pockets, the only attachments designed to lift the HalfPACT package, are designed with a minimum safety factor of three against yielding, per the requirements of 10 CFR &sect;71.45(a). The lifting devices in the OCA lid are restricted to only lifting the OCA lid, and the lifting devices in the ICV lid are restricted to only lifting an ICV lid or empty ICV. Although these lifting devices are designed with a minimum safety factor of three against yielding, detailed analyses are not specifically included herein since these lifting devices are not intended for lifting a HalfPACT package.
When lifting the entire package, the applied lift force without yielding is simply three times the total package weight of 18,100 pounds, as given in Section 2.2, Weights and Centers of Gravity.
FL = (3)(18,100) = 54,300 pounds 2.5-1
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 The entire package is lifted via two fork lift pockets located at the bottom of the OCA. Loads are considered to be concentrated at the fork lift pocket interfaces and act parallel to the direction of foam rise. For the purposes of this analysis, the minimum assumed fork width is 8 inches, and the minimum assumed engagement length is 60 inches. The total bearing area for two forks is:
A = (2)(8)(60) = 960 in2 Assuming the entire lifted load is carried directly into the polyurethane foam, thereby ignoring any beneficial load carrying associated with the presence of the relatively stiff stainless steel fork lift pocket and OCA outer shell, the compressive stress is:
F1 54,300 c =    =          = 57 psi A    960 The allowable compressive stress for the polyurethane foam is 100 psi. Therefore, the margin of safety is:
100 MS =        1 = +0.75 57 2.5.2      Tie-down Devices The HalfPACT package is secured to its dedicated semi-trailer at four points, two on each trailer main beam. For railcar shipments, the HalfPACT package is secured to an adapter that mimics the trailers four attachment points. Subsequent use of the term trailer or trailer main beam(s) encompass the railcar adapter and railcar frame. The attachment is made using trailer tie-down devices that pass over the tie-down lugs located at the bottom of the OCA body. The semi-trailer is also fitted with kick plates at the four tie-down points to provide horizontal restraint (blocking). The tie-down scheme utilized for the HalfPACT package is illustrated in Figure 2.5-1 and Figure 2.5-2.
Inertial loads of 10g longitudinally, 5g laterally, and 2g vertically, per 10 CFR &sect;71.45(b)(1), are applied through the HalfPACT package center of gravity, conservatively assumed to be 45 inches above the packages base. The horizontal loads of 10g longitudinally and 5g laterally are reacted in compression against the kick plates. The resultant overturning moment is reacted in compression on a trailer main beam and in tension by the four tie-down lugs. The vertical load applied to the center of gravity (2g) is evenly reacted at the four tie-down points, and is assumed to act in the direction (up or down) that maximizes the total tie-down load (i.e., down for the compressive reaction point and up for the tensile reaction points).
2.5.2.1      Tie-down Forces Tensile tie-down points are on a 48.4-inch radius circle (to the center of the tie-down lugs, in line with the tie-down fixture). The compressive reaction point is at the trailer main beam, occurring at the edge of the tie-down lugs doubler plate, a radius of 47.56 inches. A plan view of the tie-down geometry is depicted in Figure 2.5-3, including a corresponding free-body force diagram.
If the HalfPACT package is treated as a rigid body, the reaction forces may be determined from the following set of equations:
F1L1 + F2L2 + F3L3 + F4L4 = HFg 2.5-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 F1 F2        F    F
                                            =      = 3 = 4 =k L1 L 2 L 3 L 4 F1 + F2 + F3 + F4 = Fc where, the height of the package center of gravity above its base, H = 45 inches, the horizontal inertia force, Fg = 18,100 x (102 + 52)1/2 = 202,364 pounds, and the tie-down lug reaction lengths, L1 = 47.56 - 47.52 = 0.04 inches, L2 = 47.56 - 21.16 = 26.40 inches, L3 = 47.56 + 21.16 = 68.72 inches, and L4 = 47.56 + 47.52 = 95.08 inches. Solving for k:
HFg                            (45)(202,364) k=    2    2    2
                                    =                                            = 630 lb/in L +L +L +L 1    2    3 2
4  (0.04) + (26.40) 2 + (68.72) 2 + (95.08) 2 2
Therefore, F1 = k x L1 = 25 pounds, F2 = k x L2 = 16,632 pounds, F3 = k x L3 = 43,294 pounds, F4 = k x L4 = 59,900 pounds, and Fc = 119,851 pounds. The maximum vertical tensile force on any single tie-down lug, including the contribution of the vertical load of 2g, is then found as:
(2 g)(18,100)
Ft max = 59,900 +                = 68,950 pounds 4 lugs Similarly, the maximum compressive force is found as:
(2 g )(18,100)
Fc max = 119,851 +                = 128,901 pounds 4 lugs Since the line of action of the combined 10g longitudinal and the 5g lateral accelerations pass almost exactly over the centerline of the kickplate (27.6&#xba; for the kickplate centerline versus 26.6&#xba; for the line of action of the force), the total horizontal reaction force is conservatively assumed to be reacted against a single kickplate. This force is given by:
Fh = Fg = 202,364 pounds 2.5.2.2      Tie-down Stress Due to a Vertical Tensile Load Several failure modes are considered for the vertical tensile force on the tie-down lug. Shear failure of the tie-down lug itself is not an issue because the shear area of the lug is much greater than the lug attachment welds. The remaining failure modes, as illustrated in Figure 2.5-4, are:
(a) Shear and bending failure of the tie-down lug welds (shear + bending loads),
(b) Tearout of the tie-down lug doubler plate at the lug weld outline, (c) Shear failure of the welds attaching the lug doubler plate to the OCA outer shell, and (d) Tearout of the OCA outer shell at the doubler outline.
2.5.2.2.1      Failure of the Tie-down Lug Welds Due to Shear and Bending Loads Figure 2.5-5 presents dimensional details of the tie-down, including an appropriate free-body diagram. The length of the tie-down lug weld along the two sides is 5.49 inches. The arc length of the weld across the top of the lug is 3.38 inches. The groove weld at the bottom is 2.38 inches long. On three sides, the weld is a 3/8-inch fillet over a 3/8-inch groove. The minimum throat 2.5-3
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 length for this weld is 0.375/(sin 45&#xba;) = 0.53 inches. For the 3/8-inch groove weld at the bottom, the minimum throat length is 0.375 inches. Thus, the total shear area for the weld is:
As = [(2)(5.49) + 3.38](0.53) + (2.38) (0.375) = 8.50 in2 The maximum shearing force, V, is the maximum tensile force, Ftmax = 68,950 pounds from Section 2.5.2.1, Tie-down Forces, resulting in a corresponding shear stress of:
V 68,950 V =    =          = 8,112 psi As    8.50 The maximum weld shear stress due to bending is found using the standard beam bending formula, but by treating the weld as a line 1, or:
Mc B =
I where, M is the moment on weld group, c is the maximum weld distance from the weld group centroid, and  is the moment of inertia of weld group. The weld group centroid, relative to the bottom edge of the tie-down lug, is:
(0.53)(3.38)(6.00) + 2(0.53)(5.49)(5.49 2) y=                                                    = 3.143 inches (0.53)(3.38) + 2(0.53)(5.49) + (0.375)(2.38) where the centroid of the arc formed by the weld at the top of the tie-down lug is located 6.00 inches above the base of the lug. For the sides, the contribution to the moment of inertia is:
tL3              (0.53)(5.49) 3                          5.49 2
I s = 2    + Ad 2  = 2                + (0.53)(5.49) 3.143            = 15.54 in 4
12                    12                                  2 For the top (arc-shaped) weld, conservatively ignoring the moment of inertia about its own centroid, the contribution to the moment of inertia is:
t = Ad2 =(0.53)(3.38)(6.00 - 3.143)2 = 14.62 in4 For the bottom weld, the contribution to the moment of inertia is:
b = Ad2 = (0.375)(2.38)(3.143)2 = 8.82 in4 Summing the contributions from each part of the weld group, the total moment of inertia of the weld group, treated as a line, is:
                              = s + t + b = 15.54 + 14.62 + 8.82 = 38.98 in4 The distance from the centroid of the weld group to the extreme fiber is c = 3.143 inches. The line of action for the vertical force is 0.7 inches from the side of the tie-down doubler plate, as illustrated in Figure 2.5-5. Therefore, the shear stress on the weld group due to bending is:
1 Shigley, Mechanical Engineering Design, Third Edition, McGraw-Hill, Inc., 1977, Section 7-4, Bending in Welded Joints.
2.5-4
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 Mc (68,950)(0.7)(3.143)
B =      =                        = 3,892 psi I              38.98 The maximum shear stress in the tie-down lug weld due to the shear and bending loads is:
                            =  2V +  2B = (8,112) 2 + (3,892) 2 = 8,997 psi The allowable shear stress for the tie-down lug welds is 16,200 psi. Therefore, the margin of safety is:
16,200 MS =          1 =+ 0.80 8,997 2.5.2.2.2    Tearout of the Tie-down Doubler Plate at the Tie-Down Lug Weld Outline Assume that a rectangular region equal to 2.88 + 2 x 0.375 = 3.63 inches wide by (6.25 + 0.375)
= 6.63 inches high, tears out from the 3/8-inch thick doubler plate. Under the direct shear load of 68,520 pounds, the top edge will be in direct tension while the sides and bottom will be in direct shear. Conservatively assuming the top and sides are all in direct shear, the shear area in the 3/8-inch thick, tie-down doubler plate is:
Ap = [3.63 + 2(6.63)](0.375) = 6.33 in2 The shear area of the 1.0-inch groove weld attaching the bottom of the doubler plate to the OCA body flat head is:
Aw = (3.63)(1.0) = 3.63 in2 Thus, the total shear area is:
As = Ap + Aw = 6.33 + 3.63 = 9.96 in2 The maximum shearing force, V, is the maximum tensile force, Ftmax = 68,950 pounds from Section 2.5.2.1, Tie-down Forces, resulting in a corresponding shear stress of:
V 68,950 V =      =          = 6,923 psi As    9.96 The maximum weld shear stress due to bending is found using the standard beam bending formula, but by treating the weld as a line, or:
Mc B =
I where, M is the moment on weld group, c is the maximum weld distance from the weld group centroid, and  is the moment of inertia of weld group. The weld group centroid, relative to the bottom edge of the tie-down lug, is:
(0.375)(3.63)(6.63) + 2(0.375)(6.63)(6.63 2) + (1.0)(3.63)(1.0 2) y=                                                                      = 2.742 inches (0.375)(3.63) + 2(0.375)(6.63) + (1.0)(3.63) 2.5-5
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 For the sides of the rectangular region, the contribution to the moment of inertia is:
tL3        2 (0.375)(6.63) 3                              6.63 2
4 Is = 2      + Ad  = 2                        + (0.375)(6.63) 2.742              = 19.85 in 12                        12                                      2 For the top of the rectangular region, the contribution to the moment of inertia is:
Lt 3            (3.63)(0.375) 3 It =      + Ad 2 =                      + (0.375)(3.63)(6.63  2.742) 2 = 20.59 in 4 12                      12 For the bottom groove weld, the contribution to the moment of inertia is:
2 Lt 3            (3.63)(1.0) 3                        1.0              4 Ib =        + Ad 2 =                  + (1.0)(3.63) 2.742      = 18.55 in 12                    12                              2 Summing the contributions from each part of the rectangular region, the total moment of inertia of the weld group, treated as a line, is:
                              = s + t + b = 19.85 + 20.59 + 18.55 = 58.99 in4 The distance from the centroid of the rectangular region to the extreme fiber is c = 6.63 - 2.742
= 3.888 inches. The line of action for the vertical force is 0.7 + 0.375/2 = 0.89 inches from the center of the tie-down doubler plate. Therefore, the shear stress due to bending is:
Mc (68,950)(0.89)(3.888)
B =        =                            = 4,103 psi I              58.99 The maximum shear stress in the tie-down doubler plate due to the shear and bending loads is:
                                =  2V +  2B = (6,923) 2 + (4,103) 2 = 8,048 psi The allowable shear stress for the tie-down doubler plate is 16,200 psi. Therefore, the margin of safety is:
16,200 MS =            1 =+ 1.01 8,048 2.5.2.2.3      Shear Failure of the Tie-down Lug Doubler Plate to OCA Outer Shell Welds The tie-down lug doubler plate is 24 inches square, and welded to the OCA outer shell on its top and sides with 1/4-inch fillet welds. Although the bottom weld is a groove weld, conservatively assume it acts as a 1/4-inch fillet weld, resulting in a total weld length of 96 inches. In addition, 30, 11/2-inch diameter, 1/4-inch fillet welds supplement the peripheral fillet welds, providing an additional 30 x (1.5) = 141 inches of weld. Thus, the total weld length is 237 inches, resulting in a weld shear area of:
As = (0.25)(sin 45&#xba;)(237) = 41.9 in2 The weld shear area is much greater than determined in both previous cases (i.e., As = 8.50 in2 for Section 2.5.2.2.1, Failure of the Tie-down Lug Welds Due to Shear and Bending Loads, and As = 9.96 in2 for Section 2.5.2.2.2, Tearout of the Tie-down Doubler Plate at the Tie-Down Lug 2.5-6
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 Weld Outline). Thus, the weld shear stress for the same vertical load will be correspondingly less. Similarly, a much larger moment of inertia will be determined for a nearly identical bending moment, thereby resulting in a substantially reduced bending stress. In conclusion, by inspection the resulting margin of safety will correspondingly be much greater and does not need to be explicitly determined.
2.5.2.2.4    Tearout of the OCA Outer Shell at the Tie-Down Lug Doubler Plate Outline A potential failure mode for the tie-down hardware is tearout of the 1/4-inch thick OCA outer shell just outboard of the 24.0-inch square doubler plate. The downward acting force puts the OCA shell adjacent to the top edge of the doubler plate in direct tension. The OCA outer shell immediately adjacent to the sides and bottom edge of the doubler plate is in direct shear.
Assume that the 24- x 24-inch tie-down lug doubler plate tears out from 1/4-inch thick OCA outer shell. Under the direct shear load of 68,520 pounds, the top edge will be in direct tension while the sides and bottom will be in direct shear. Conservatively assuming that all sides are all in direct shear, the shear area in the 1/4-inch thick OCA outer shell is:
As = 4(24)(0.25) = 24.0 in2 Once again, the shell shear area is much greater than determined in both previous cases (i.e.,
As = 8.50 in2 for Section 2.5.2.2.1, Failure of the Tie-down Lug Welds Due to Shear and Bending Loads, and As = 9.96 in2 for Section 2.5.2.2.2, Tearout of the Tie-down Doubler Plate at the Tie-Down Lug Weld Outline). Thus, the weld shear stress for the same vertical load will be correspondingly less. As before, a much larger moment of inertia will be determined for a nearly identical bending moment, thereby resulting in a substantially reduced bending stress. In conclusion, by inspection the resulting margin of safety will correspondingly be much greater and does not need to be explicitly determined.
2.5.2.3      Tie-down Stress Due to a Vertical Compressive Load The stresses in the HalfPACT package due to a vertical compressive load may be analyzed by two bounding cases. First, the combination of overturning and vertical, 2g inertial compressive loads carried through the OCA outer shell and tie-down lug doubler plate, and second, the 2g inertial compressive load carried entirely by the polyurethane foam.
2.5.2.3.1    Bearing Stress in the OCA Outer Shell and Tie-down Lug Doubler Plate The vertical compressive tie-down load is carried in bearing against the semi-trailer main beams.
Conservatively assume that this load is carried only by the cylindrical portion of the OCA outer shell and doubler that is directly over the trailer main beams and tie-down support structure.
With reference to Figure 2.5-3, the arc length, s, of the OCA that spans the trailer main beams is:
1  32            1  18 s = R      (1  2 ) = (47.56)      sin          sin          = 16.64 inches 180                      180        47.56          47.56 For an OCA outer shell thickness of 1/4 inches, and a tie-down lug doubler plate thickness of 3/8 inches, the area is:
2.5-7
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 A = (16.64)(0.25 + 0.375) = 10.40 in2 Thus, from Section 2.5.2.1, Tie-down Forces, the maximum compressive force is Fcmax = 128,901 pounds, and the corresponding compressive stress is:
Fc max 128,901 c =      =          = 12,394 psi A      10.40 The allowable stress for the OCA outer shell and tie-down lug doubler plate is 27,000 psi.
Therefore, the margin of safety is:
27,000 MS =            1 = +1.18 12,394 2.5.2.3.2      Compressive Stress in the Polyurethane Foam The HalfPACT package is supported on the two main trailer beams during transport. With reference to Figure 2.5-3, the length, L, under the OCA that spans the trailer main beams is:
L = 2 (47.56) 2  (22) 2 = 84.3 inches For two, 8-inch wide trailer main beams, the total compressive area is:
A = 2(8)(84.3) = 1,349 in2 Conservatively ignoring the load carrying capacity of the OCA outer shell and fork lift pockets, the compressive stress in the polyurethane foam due to a 2g vertical (downward) inertial force is:
2(18,100) 36,200 c =            =          = 27 psi A        1,349 The allowable stress for the polyurethane foam is 100 psi. Therefore, the margin of safety is:
100 MS =        1 = +2.70 27 2.5.2.4      Tie-down Stresses Due to a Horizontal Compressive Load The horizontal load, Fh = 202,364 pounds, determined in Section 2.5.2.1, Tie-down Forces, is reacted by a single tie-down weldment. The following sections consider the bearing stress in the tie-down weldment, and the shear stresses in the welds holding the horizontal tripler plate to the doubler plate, and the doubler plate to the lower OCA flat head. Based on their relative thicknesses, assume that one-quarter the horizontal load is carried through the 1/4-inch thick OCA flat head, one-quarter is carried through the 1/4-inch thick doubler plate, and one-half is carried through the 1/2-inch thick tripler plate.
2.5.2.4.1      Bearing Stress in the Tie-down Weldment The horizontal load, Fh = 202,364 pounds, is carried from the 8.0 inch wide trailer kickplate through the horizontal doubler and tripler plates welded inside the lower OCA flat head, as illustrated in Figure 2.5-3. For a kickplate length, L = 8 inches, a bottom shell thickness, ts = 1/4 2.5-8
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 inch, a doubler plate thickness, td = 1/4 inch, and a tripler plate thickness, tt = 1/2 inch, the area available to carry the horizontal compressive load at the kickplate interface is:
A = L(ts + td + tt) = (8.0)(0.25 + 0.25 + 0.5) = 8.0 in2 The corresponding compressive (bearing) stress is:
Fh 202,364 c =      =          = 25,296 psi A      8.0 The allowable bearing stress for the OCA outer shell, including the horizontal doubler and tripler plates, is 27,000 psi. Therefore, the margin of safety is:
27,000 MS =            1 = +0.07 25,296 2.5.2.4.2      Shear Stress in the Tripler Plate Welds Based on the assumed load distribution in Section 2.5.2.4, Tie-down Stresses Due to a Horizontal Compressive Load, the force on the welds attaching the tripler plate to the doubler plate is then one-half of 202,364 pounds, or 101,182 pounds. The tripler plate is welded with 3/8-inch fillet welds along three of its edges, and a 1/2-inch groove weld along the outer edge. The two side welds are approximately 8 inches long, and the back weld is 7 inches long, for a total, 3/8-inch fillet weld length of 23 inches. Four, 11/2-inch diameter, 3/8-inch fillet welds supplement the peripheral 3/8-inch fillet welds, providing an additional 4 x (1.5) = 18.85 inches of 3/8-inch fillet weld. Thus, the total 3/8-inch fillet weld length is 41.85 inches. In addition, the 10-inch long outer edge is welded with a 1/2-inch groove weld. The resulting weld shear area is:
As = (0.375)(sin 45&#xba;)(41.85) + (0.5)(10) = 16.1 in2 Thus, the shear stress in the tripler plate fillet welds is:
101,182
                                          =            = 6,285 psi 16.1 The allowable shear stress for the tripler plate welds is 16,200 psi. Therefore, the margin of safety is:
16,200 MS =            1 = +1.58 6,285 As an option, the tripler plate may be one inch thick and welded into a cutout through the 1/4-inch thick lower OCA flat head and 1/4-inch thick doubler plate in the same orientation and location as shown in Figure 2.5-6. Full penetration groove welds are used around the periphery of the tripler plate (i.e., a one-inch groove weld along the outside, 10-inch long edge, and 1/2-inch groove welds along the remaining three edges). The two side welds are approximately 8 inches long, and the back weld is 7 inches long, for a total weld length of 23 inches. The resulting weld shear area is:
A = (0.5)(23) + (1.0)(10) = 21.5 in2 2.5-9
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Thus, the shear stress in the tripler plate groove welds is:
101,182
                                        =          = 4,706 psi 21.5 The allowable shear stress for the tripler plate welds is 16,200 psi. Therefore, the margin of safety is:
16,200 MS =          1 = +2.44 4,706 2.5.2.4.3      Shear Stress in the Doubler Plate Welds Based on the assumed load distribution in Section 2.5.2.4, Tie-down Stresses Due to a Horizontal Compressive Load, the force on the welds attaching the doubler plate to the OCA flat head is then one-half plus one-quarter of 202,364 pounds, or 151,773 pounds. The doubler plate is welded with 1/4-inch fillet welds along its four inner edges, for a total 1/4-inch fillet weld length of approximately 35 inches. Eighteen, 1-inch diameter, 1/4-inch fillet welds supplement the peripheral 1/4-inch fillet welds, providing an additional 18 x (1.0) = 56 inches of 1/4-inch fillet weld. Thus, the total 1/4-inch fillet weld length is 91 inches. In addition, the 20 inch long outer edge is welded with a 1/4-inch groove weld. The resulting weld shear area is:
As = (0.25)(sin 45&#xba;)(91) + (0.25)(20) = 21.1 in2 Thus, the shear stress in the doubler plate fillet welds is:
151,773
                                        =          = 7,193 psi 21.1 The allowable shear stress for the doubler plate welds is 16,200 psi. Therefore, the margin of safety is:
16,200 MS =          1 =+ 1.25 7,193 2.5.2.5    Response of the Package if Treated as a Fixed Cantilever Beam The preceding sections considered stresses in a localized region in and around the tie-down components. This section demonstrates that a more global response of the HalfPACT package to tie-down loads is also acceptable. For this assessment, the HalfPACT package is treated as a cantilever beam, fixed at its base. The 1/4-inch thick, OCA outer shell is conservatively assumed to be the only structural member resisting the applied 10g, 5g and 2g inertia loads. Stress intensity, SI, in the OCA outer shell is determined as follows:
2                    2      2 P Mc  2V SI = 2  +  2 =  +            +
2          A      I  A where, for 2g vertically, the axial force, P = (2)(18,100) = 36,200 pounds, the bending moment from Section 2.5.2.1, Tie-down Forces, M = HFg = (45)(202,364) = 9,106,380 in-lbs, the extreme fiber distance, c = 1/2(94) = 47.2 inches, the horizontal shear force, V = Fg = 202,364 inches, the OCA outer shell cross-sectional area, A = (/4)[(94.375)2 - (93.875)2] = 74 in2, and the OCA 2.5-10
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 outer shell moment of inertia, I = (/64)[(94.375)4 - (93.875)4] = 81,869 in4. The resulting stress intensity is:
2                2 36,200 (9,106,380)(47.2)  2(202,364)
SI =          +                      +              = 7,928 psi 74              81,869                74 The allowable stress intensity for the OCA outer shell is 27,000 psi. Therefore, the margin of safety is:
27,000 MS =            1 =+ 2.41 7,928 2.5.2.6      Summary All margins of safety for tie-down loads, per 10 CFR &sect;71.45(b)(1), are positive. The smallest tensile or shear margin of safety, MS = +0.80, is for failure of the welds attaching the tie-down lug to the doubler plate, indicating that this will be the mode of failure for the tie-downs under an excessive load condition. Note that compressive modes of failure are not considered relevant in the excessive load evaluation. In accordance with 10 CFR &sect;71.45(b)(3), this failure mode does not compromise the performance capabilities of the HalfPACT package since no main shell is breached. Finally, it is noted that the fork lift pockets and OCA lifting sockets are not intended to be used as tie-down devices, and are appropriately disabled to prevent inadvertent use. The fork lift pockets and OCA lifting sockets are disabled by affixing a plate over each pocket and a cover over the each socket respectively (see the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings).
2.5-11
 
HalfPACT Safety Analysis Report        Rev. 9, August 2022 Figure 2.5 Tie-down Device Layout 2.5-12
 
HalfPACT Safety Analysis Report        Rev. 9, August 2022 Figure 2.5 Tie-down Device Detail 2.5-13
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.5 Tie-down Plan View and Reaction Force Diagram 2.5-14
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 2.5 Tie-down Tensile/Shear Failure Modes 2.5-15
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.5 Tie-down Lug Dimensions and Load Diagram 2.5-16
 
HalfPACT Safety Analysis Report                          Rev. 9, August 2022 Figure 2.5 Horizontal Doubler and Tripler Plate Details 2.5-17
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.5-18
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 2.6 Normal Conditions of Transport The HalfPACT package, when subjected to the normal conditions of transport (NCT) specified in 10 CFR &sect;71.71 1, is shown to meet the performance requirements specified in Subpart E of 10 CFR 71.
As discussed in the introduction to this chapter, with the exception of the NCT free drop, the primary proof of NCT performance is via analytic methods. Regulatory Guide 7.6 2 criteria are demonstrated as acceptable for all NCT analytic evaluations presented in this section. Specific discussions regarding brittle fracture and fatigue are presented in Section 2.1.2.2, Miscellaneous Structural Failure Modes, and are shown not to be limiting cases for the HalfPACT package design. The ability of the butyl O-ring containment seals to remain leaktight is documented in Appendix 2.10.2, Elastomer O-ring Seal Performance Tests.
With the exception of the NCT free drop evaluation, analyses for heat, cold, reduced external pressure, increased external pressure, and vibration are performed in this section. Allowable stress limits are consistent with Table 2.1-1 and Table 2.1-2 in Section 2.1.2.1, Analytic Design Criteria (Allowable Stresses), using temperature-adjusted material properties taken from Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations.
For the analytic assessments performed within this section, properties for Type 304 stainless steel are based on data from Table 2.3-1 from Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations). Similarly, the bounding values for polyurethane foam compressive strength are based on data from Table 2.3-2 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations. Polyurethane foam compressive strength is further adjusted +/-15% to account for manufacturing tolerance. At elevated NCT temperatures (i.e., 160 &#xba;F), the nominal compressive strength is reduced 25% for elevated temperature effects and reduced 15% for manufacturing tolerance. At reduced NCT temperatures (i.e., -40 &#xba;F), the nominal compressive strength is increased 50% for reduced temperature effects and increased 15% for manufacturing tolerance.
Properties of Type 304 stainless steel and polyurethane foam are summarized below.
Material Property Value (psi)
Material Property                      -40 &deg;F          70 &deg;F          160 &deg;F        Reference Type 304 Stainless Steel Elastic Modulus, E                  28.8 x 106      28.3 x 106      27.8 x 106 Design Stress Intensity, Sm                20,000          20,000          20,000        Table 2.3-1 Yield Strength, Sm                    30,000          30,000          27,000 Polyurethane Foam Compressive Strength Parallel-to-Rise Direction, c                405            235              150 Table 2.3-2 Perpendicular-to-Rise Direction, c                336            195              124 1
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 U. S. Nuclear Regulatory Commission, Regulatory Guide 7.6, Design Criteria for the Structural Analysis of Shipping Cask Containment Vessels, Revision 1, March 1978.
2.6-1
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Finite element analysis methods are utilized to determine stresses in the HalfPACT packaging structure at various temperature extremes, including the effects of differential thermal expansion, when appropriate, and internal (I) and external (E) pressure combinations, as summarized below.
Load Case    Reference Differential      Pressure        Temperature        Table      Figure Number      Section Expansion?        Differential  Uniform Reference Number          Numbers OCA Case 1      &sect;2.6.1        No        61.2 psig (I)  160 &#xba;F    160 &#xba;F      2.6-1      2.6-1/-2 OCA Case 2      &sect;2.6.1      Yes        61.2 psig (I)  160 &#xba;F      70 &#xba;F      2.6-2      2.6-3/-4 OCA Case 3      &sect;2.6.2      Yes          0 psig        -40 &#xba;F    70 &#xba;F      2.6-3      2.6-5/-6 OCA Case 4      &sect;2.6.4        No        14.7 psig (E)    70 &#xba;F    70 &#xba;F      2.6-4      2.6-7/-8 ICV Case 1      &sect;2.6.1        No        61.2 psig (I)  160 &#xba;F    160 &#xba;F      2.6-5      2.6-9/-10 ICV Case 2      &sect;2.6.4        No        14.7 psig (E)    70 &#xba;F    70 &#xba;F      2.6-6    2.6-11/-12 For the NCT free drop evaluation, a certification test program was undertaken using a HalfPACT engineering and certification test unit (ETU and CTU, respectively). Results from certification testing demonstrated that under NCT free drop conditions, two leaktight levels of containment were maintained. NCT certification testing also demonstrated the HalfPACT packages ability to survive subsequent HAC 30-foot free drop, puncture, and fire tests was not compromised.
Analyses are performed, when appropriate, to supplement or expand on the available test results.
This combination of analytic and test, structural evaluations provides an initial configuration for NCT thermal, shielding and criticality performance. In accordance with 10 CFR &sect;71.43(f), the evaluations performed herein successfully demonstrate that under NCT tests the HalfPACT package experiences no substantial reduction in the effectiveness of the packaging.
Summaries of the more significant aspects of the full scale free drop testing are included in Section 2.6.7, Free Drop, with details presented in Appendix 2.10.3, Certification Tests.
2.6.1      Heat The NCT thermal analyses presented in Section 3.4, Thermal Evaluation for Normal Conditions of Transport, consists of exposing the HalfPACT package to direct sunlight and 100 &#xba;F still air per the requirements of 10 CFR &sect;71.71(b). Although the actual internal heat load is a function of the particular payload configuration being transported, this section utilizes the maximum internal heat allowed within a HalfPACT package, or 30 thermal watts. The 30 thermal watt case results in maximum temperature gradients throughout the HalfPACT package.
2.6.1.1    Summary of Pressures and Temperatures The maximum normal operating pressure (MNOP) is 50 psig, as determined in Section 3.4.4, Maximum Internal Pressure. The pressure stress analyses within this section combine the internal pressure of 50 psig due to MNOP with a reduced external pressure, per 10 CFR
&sect;71.71(c)(3), of 3.5 psia (11.2 psig). The net resulting internal pressure utilized in all NCT structural analyses considering internal pressure is therefore 61.2 psig.
The NCT heat input results in modest temperatures and temperature gradients throughout the HalfPACT package. Maximum temperatures for the major packaging components are summarized 2.6-2
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 in Table 3.4-1 from Section 3.4.2, Maximum Temperatures. As shown in Table 3.4-1, all packaging temperatures remain at or below 155 &#xba;F. For conservatism, structural analyses of the OCA and ICV utilize a uniform bounding temperature of 160 &#xba;F. Use of a uniform bounding temperature is also conservative since material strengths are lowest at the highest temperatures. In addition, in the case of the OCA, the main contributor to thermal stress is the result of differential expansion of the polyurethane foam and the surrounding stainless steel. Also shown by the temperatures presented in Table 3.4-1, temperature gradients are modest for the NCT heat condition. Thus, temperature gradients are reasonably ignored in the analyses herein.
2.6.1.2      Differential Thermal Expansion With NCT temperatures throughout the packaging being relatively uniform, (i.e., no significant temperature gradients), the concern with differential expansions is limited to regions of the HalfPACT packaging that employ adjacent materials with sufficiently different coefficients of thermal expansion. The OCA is a double-wall, composite construction of polyurethane foam between inner and outer shells of stainless steel. The polyurethane foam expands and contracts to a much greater degree than the surrounding stainless steel shells resulting in stresses due to differential thermal expansion. Finite element analyses presented in the following sections quantify these differential thermal expansion stresses. Differential thermal expansion stresses are negligible in the ICV for three reasons: 1) the temperature distribution throughout the entire ICV is relatively uniform, 2) the ICV is fabricated from only one type of structural material, and
: 3) the ICV is not radially or axially constrained within a tight-fitting structure (i.e., the OCV).
2.6.1.3      Stress Calculations A finite element model of the OCA is used to determine the stresses due to the combined effects of pressure loads, and temperature loads due to differential thermal expansion. The details of this model are presented in Appendix 2.10.1.1, Outer Confinement Assembly (OCA) Structural Analysis. The ICV is also analyzed for the combined effects of pressure and temperature using a finite element model that is described in Appendix 2.10.1.2, Inner Containment Vessel (ICV)
Structural Analysis. For the NCT heat condition, evaluations include two load cases for the OCA and one load case for the ICV.
Maximum stress intensities are determined for each component, and classified according to primary or secondary, membrane or bending. Classification of stress intensities is per Table NB-3217-1 of the ASME Boiler and Pressure Vessel Code 3. Maximum stress intensities are presented for the maximum general primary membrane stress intensity, Pm, the maximum local primary membrane stress intensity, PL, the maximum primary membrane (general or local) plus primary bending stress intensity, Pm + Pb or PL + Pb, and the maximum primary plus secondary stress intensity, Pm + Pb + Q or PL + Pb + Q.
OCA Load Case 1 (see Table 2.6-1 and Figure 2.6-1 and Figure 2.6-2): This analysis is performed at a uniform temperature of 160 &#xba;F, but with the reference temperature also set to 160 &#xba;F thereby eliminating any differential thermal expansion stresses. The internal pressure considers the effects of a maximum normal operating pressure (MNOP) of 50 psig, internal, 3
American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, 1995 Edition, 1997 Addenda.
2.6-3
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 coupled with a reduced external pressure of 3.5 psia (i.e., 11.2 psig, internal). The net result is an internal pressure of 50.0 + 11.2 = 61.2 psig.
Pm  = 19,061 psi, located in the OCV shell at the cylindrical/conical transition, PL  = 28,084 psi, located in the knuckle region of the upper OCV torispherical head, PL + Pb  = 20,256 psi, located in the OCV shell at the cylindrical/conical transition, and PL + Pb + Q    = 39,884 psi, located in the knuckle region of the lower OCV torispherical head.
OCA Load Case 2 (see Table 2.6-2 and Figure 2.6-3 and Figure 2.6-4): This analysis is performed at a uniform temperature of 160 &#xba;F, but with the reference temperature set to 70 &#xba;F thereby including any differential thermal expansion stresses. As with OCA Load Case 1, the MNOP is coupled with the reduced external pressure for a net internal pressure of 61.2 psig. The use of these two cases allows primary stress intensities (from pressure loads) to be considered independently of secondary stress intensities (from differential thermal expansion loads).
PL + Pb + Q = 40,200 psi, located in the knuckle region of the lower OCV torispherical head.
ICV Load Case 1 (see Table 2.6-5 and Figure 2.6-9 and Figure 2.6-10): This analysis is performed at a uniform temperature of 160 &#xba;F, but with the reference temperature also set to 160 &#xba;F thereby eliminating any differential thermal expansion stresses. As with OCA Load Cases 1 and 2, the MNOP is coupled with the reduced external pressure for a net internal pressure of 61.2 psig.
Pm  = 15,251 psi, located in the upper ICV seal flange/shell transition, PL  = 26,968 psi, located in the knuckle region of the upper ICV torispherical head, PL + Pb  = 22,336 psi, located in the upper ICV seal flange/shell transition, and PL + Pb + Q    = 38,304 psi, located in the knuckle region of the upper ICV torispherical head.
Polyurethane foam stress intensities are insignificant for OCA Load Case 1 (maximum stress intensity is 3 psi) and achieve a maximum value of 26 psi for OCA Load Case 2. Based on the perpendicular-to-rise direction at 160 &#xba;F, the minimum, polyurethane foam margin of safety is:
124 MS =        1 = +3.77 26 2.6.1.4      Comparison with Allowable Stresses Section 2.1.2, Design Criteria, presents the design criteria for structural evaluation of the HalfPACT packaging. The containment vessel design criteria for NCT analyses are in accordance with Regulatory Guide 7.6, which uses as a basis the criteria defined for Level A service limits in Section III of the ASME Boiler and Pressure Vessel Code 4. Load combinations follow the guidelines of Regulatory Guide 7.8 5.
From Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the design stress intensity for Type 304 stainless steel used in the ICV and OCV is Sm = 20,000 psi at 160 &#xba;F. From Table 2.1-1 in Section 2.1.2.1.1, Containment Structure (ICV), the allowable 4
American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, 1995 Edition, 1997 Addenda.
5 U. S. Nuclear Regulatory Commission, Regulatory Guide 7.8, Load Combinations for the Structural Analysis of Shipping Casks for Radioactive Material, Revision 1, March 1989.
2.6-4
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 stress intensities for the NCT hot condition is Sm for general primary membrane stress intensity (Pm), 1.5Sm for local primary membrane stress intensity (PL), 1.5Sm for primary membrane (general or local) plus primary bending stress intensity (Pm + Pb or PL + Pb ), and 3.0Sm for the range of primary plus secondary stress intensity (Pm + Pb + Q or PL + Pb + Q).
Maximum stress intensity, allowable stress intensity, and minimum margins of safety for each stress category and each load case are presented in Table 2.6-1, Table 2.6-2, and Table 2.6-5 for each of the cases discussed above. Since all margins of safety are positive, the design criteria are satisfied.
2.6.1.5      Range of Primary Plus Secondary Stress Intensities Per Paragraph C.4 of Regulatory Guide 7.6, the maximum range of primary plus secondary stress intensity for NCT must be less than 3.0Sm. This limitation on stress intensity range applies to the entire history of NCT loadings and not only to the stresses from each individual load transient.
2.6.1.5.1      Range of Primary Plus Secondary Stress Intensities for the OCA The extreme ends of the stress range are determined from OCA Load Case 2 (from Section 2.6.1, Heat) and OCA Load Case 4 (from Section 2.6.4, Increased External Pressure). One extreme, OCA Load Case 2 represents the case of maximum internal pressure coupled with reduced external pressure, plus the effect of differential thermal expansion associated with heat-up from 70 &#xba;F to 160 &#xba;F. The other extreme, OCA Load Case 4, considers the effect of a minimum internal pressure at 70 &#xba;F. Note that combinations of other OCA load cases such as increased external pressure (20 psia, 5.3 psig) plus cool-down from 70 &#xba;F to -20 &#xba;F were also considered and found not to be bounding for the stress intensity range calculation.
The maximum range of primary plus secondary stress intensity occurs in the knuckle region of the lower OCV torispherical head (element 320). The extreme values of stress intensity are 40,200 psi and 9,641 psi from Table 2.6-2 and Table 2.6-4 for OCA Load Cases 2 and 4, respectively. Since OCA Load Cases 2 and 4 have opposite loads, the maximum range of primary plus secondary stress intensity is simply 40,200 + 9,641 = 49,841 psi. The allowable stress intensity is 3.0Sm, where Sm =
20,000 psi for Type 304 stainless steel at 160 &#xba;F. The margin of safety is:
3(20,000 )
MS =              1 = +0.20 49,841 The positive margin of safety indicates that the design criterion is satisfied.
2.6.1.5.2      Range of Primary Plus Secondary Stress Intensities for the ICV The extreme ends of the stress range are determined from ICV Load Case 1 (from Section 2.6.1, Heat) and ICV Load Case 2 (from Section 2.6.4, Increased External Pressure). One extreme, ICV Load Case 1 represents the case of maximum internal pressure coupled with reduced external pressure, plus the effect of differential thermal expansion associated with heat-up from 70 &#xba;F to 160 &#xba;F. The other extreme, ICV Load Case 2, considers the effect of a minimum internal pressure at 70 &#xba;F.
The extreme values of stress intensity are 38,304 psi and 9,104 psi from Table 2.6-5 and Table 2.6-6 for ICV Load Cases 1 and 2, respectively, conservatively ignoring the fact that the extreme values occur at locations remote from each other. Since ICV Load Cases 1 and 2 have opposite loads, the maximum range of primary plus secondary stress intensity is simply 38,304 + 9,104 2.6-5
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
= 47,408 psi. The allowable stress intensity is 3.0Sm, where Sm = 20,000 psi for Type 304 stainless steel at 160 &#xba;F. The margin of safety is:
3(20,000 )
MS =            1 = +0.27 47,408 The positive margin of safety indicates that the design criterion is satisfied.
2.6.2      Cold The NCT cold condition consists of exposing the HalfPACT packaging to a steady-state ambient temperature of -40 &#xba;F. Insolation and payload internal decay heat are assumed to be zero. These conditions will result in a uniform temperature throughout the package of -40 &#xba;F. With no internal heat load (i.e., no contents to produce heat and, therefore, pressure), the net pressure differential is assumed to be zero (14.7 psia internal, 14.7 psia external).
For the OCA, the principal structural concern due to the NCT cold condition is the effect of the differential expansion of the polyurethane foam relative to the surrounding stainless steel shells.
During the cool-down from 70 &#xba;F to -40 &#xba;F, the foam material shrinks onto the OCV because thermal expansion coefficient for foam is greater than stainless steel. The resulting stresses are discussed in Section 2.6.2.1, Stress Calculations.
Differential thermal expansion stresses are negligible in the ICV for three reasons: 1) the temperature distribution throughout the entire ICV is relatively uniform, 2) the ICV is fabricated from only one type of structural material, and 3) the ICV is not radially or axially constrained within a tight-fitting structure (i.e., the OCV).
Brittle fracture at -40 &#xba;F is addressed in Section 2.1.2.2.1, Brittle Fracture. Performance of the O-ring seals at -40 &#xba;F is discussed in Appendix 2.10.2, Elastomer O-ring Seal Performance Tests.
2.6.2.1      Stress Calculations A finite element model of the OCA is used to determine the stresses due to the combined effects of pressure loads, and temperature loads due to differential thermal expansion. The details of this model are presented in Appendix 2.10.1.1, Outer Confinement Assembly (OCA) Structural Analysis. For the NCT cold condition, evaluations include one load case for the OCA.
Maximum stress intensities are determined for each component, and classified according to primary or secondary, membrane or bending. Classification of stress intensities is per Table NB-3217-1 of the ASME Boiler and Pressure Vessel Code. Membrane and membrane plus bending stresses due to differential thermal expansion are classified as secondary stresses (Q).
Since there are no pressure loads, primary stresses (Pm, PL, and Pm + Pb or PL + Pb) are equal to zero.
OCA Load Case 3 (see Table 2.6-3 and Figure 2.6-5 and Figure 2.6-6): This analysis is performed at a uniform temperature of -40 &#xba;F, but with the reference temperature set to 70 &#xba;F thereby including differential thermal expansion stresses. For a uniform temperature cold case at -40 &#xba;F, both payload decay heat and solar heat are assumed to be zero. These conditions result in an internal pressure of 14.7 psia balanced with an external pressure of 14.7 psia, for a net pressure differential of zero.
PL + Pb + Q = 5,772 psi, located in the lower OCV seal flange/Z-flange junction.
2.6-6
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 Polyurethane foam stress intensities are relatively small for OCA Load Case 3 (maximum stress intensity is 15 psi). Conservatively based on the perpendicular-to-rise direction at 160 &#xba;F, the minimum, polyurethane foam margin of safety is:
124 MS =        1 = +7.27 15 2.6.2.2      Comparison with Allowable Stresses Section 2.1.2, Design Criteria, presents the design criteria for structural evaluation of the HalfPACT packaging. The containment vessel design criteria for NCT analyses are in accordance with Regulatory Guide 7.6, which uses as a basis the criteria defined for Level A service limits in Section III of the ASME Boiler and Pressure Vessel Code. Load combinations follow the guidelines of Regulatory Guide 7.8.
From Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the design stress intensity for Type 304 stainless steel used in the ICV and OCV is Sm = 20,000 psi at -40 &#xba;F. From Table 2.1-1 in Section 2.1.2.1.1, Containment Structure (ICV), the allowable stress intensity for the NCT cold condition is 3.0Sm for the range of primary plus secondary stress intensity (Pm + Pb + Q or PL +
Pb + Q).
Maximum stress intensity, allowable stress intensity, and minimum margins of safety for each stress category and each load case are presented in Table 2.6-3 for OCA Load Case 3. Since all margins of safety are positive, the design criteria are satisfied.
Since the NCT cold condition results in shrinking of the polyurethane foam onto the OCV shell, compressive stresses develop in the OCV shell. The buckling evaluation within Section 2.6.4, Increased External Pressure, demonstrates that the compressive stresses due to increased external pressure do not exceed the NCT allowable stresses. The compressive stresses generated during the NCT cold condition are bounded by the NCT increased external pressure condition, therefore no explicit buckling evaluation is required for the NCT cold condition.
2.6.3      Reduced External Pressure The effect of a reduced external pressure of 3.5 psia (11.2 psig internal pressure), per 10 CFR
&sect;71.71(c)(3), is negligible for the HalfPACT packaging. This conclusion is based on the analyses presented in Section 2.6.1, Heat, addressing the ability of both the ICV and OCV to independently withstand a maximum normal operating pressure (MNOP) of 50 psig, combined with a reduced external pressure of 3.5 psia, for a net effective internal pressure of 61.2 psig.
2.6.4      Increased External Pressure The effect of an increased external pressure of 20 psia (5.3 psig external pressure), per 10 CFR
&sect;71.71(c)(4), is negligible for the HalfPACT packaging. Both the ICV and OCV are designed to withstand a full vacuum equivalent to 14.7 psi external pressure during acceptance leakage rate testing of the HalfPACT package, as described in Section 8.1.3, Fabrication Leakage Rate Tests.
Therefore, the worst case NCT external pressure loading is 14.7 psig.
The external pressure induces small compressive stresses in the ICV and OCV that are limited by stability (buckling) requirements. Buckling assessments are performed for the OCV and ICV in 2.6-7
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 Section 2.6.4.3, Buckling Assessment of the Torispherical Heads, and Section 2.6.4.4, Buckling Assessment of the Cylindrical Shells.
2.6.4.1      Stress Calculations A finite element model of the OCA is used to determine the stresses due to the effect of a pressure load. The details of this model are presented in Appendix 2.10.1.1, Outer Confinement Assembly (OCA) Structural Analysis. The ICV is also analyzed for the effects of a pressure using a finite element model that is described in Appendix 2.10.1.2, Inner Containment Vessel (ICV) Structural Analysis. For the NCT increased external pressure condition, evaluations include one load case for the OCA and one load case for the ICV.
Maximum stress intensities are determined for each component, and classified according to primary or secondary, membrane or bending. Classification of stress intensities is per Table NB-3217-1 of the ASME Boiler and Pressure Vessel Code. Maximum stress intensities are presented for the maximum general primary membrane stress intensity, Pm, the maximum local primary membrane stress intensity, PL, the maximum primary membrane (general or local) plus primary bending stress intensity, Pm + Pb or PL + Pb, and the maximum primary plus secondary stress intensity, Pm + Pb + Q or PL + Pb + Q.
OCA Load Case 4 (see Table 2.6-4 and Figure 2.6-7 and Figure 2.6-8): This analysis is performed at a uniform temperature of 70 &#xba;F, and the reference temperature also set to 70 &#xba;F thereby eliminating any differential thermal expansion stresses. The external pressure is 14.7 psig.
Pm  = 4,748 psi, located in the OCV shell at the cylindrical/conical transition, PL = 6,852 psi, located in the knuckle region of the upper OCV torispherical head, PL + Pb = 5,087 psi, located in the OCV shell at the cylindrical/conical transition, and PL + Pb + Q  = 9,641 psi, located in the knuckle region of the lower OCV torispherical head.
ICV Load Case 2 (see Table 2.6-6 and Figure 2.6-11 and Figure 2.6-12): This analysis is performed at a uniform temperature of 70 &#xba;F, but with the reference temperature also set to 70 &#xba;F thereby eliminating any differential thermal expansion stresses. As with OCA Load Case 4, the external pressure is 14.7 psig.
Pm  = 3,635 psi, located in the crown region of the upper ICV torispherical head, PL = 6,384 psi, located in the knuckle region of the upper ICV torispherical head, PL + Pb = 4,656 psi, located in the crown region of the upper ICV torispherical head, and PL + Pb + Q  = 9,104 psi, located in the knuckle region of the upper ICV torispherical head.
Polyurethane foam stress intensities are insignificant for OCA Load Case 4.
2.6.4.2      Comparison with Allowable Stresses Section 2.1.2, Design Criteria, presents the design criteria for structural evaluation of the HalfPACT packaging. The containment vessel design criteria for NCT analyses are in accordance with Regulatory Guide 7.6, which uses as a basis the criteria defined for Level A service limits in Section III of the ASME Boiler and Pressure Vessel Code. Load combinations follow the guidelines of Regulatory Guide 7.8.
From Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the design stress intensity for Type 304 stainless steel used in the ICV and OCV is Sm = 20,000 psi at 160 &#xba;F. From Table 2.1-1 in Section 2.1.2.1.1, Containment Structure (ICV), the allowable 2.6-8
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 stress intensities for the NCT increased external pressure condition is Sm for general primary membrane stress intensity (Pm), 1.5Sm for local primary membrane stress intensity (PL), 1.5Sm for primary membrane (general or local) plus primary bending stress intensity (Pm + Pb or PL + Pb ),
and 3.0Sm for the range of primary plus secondary stress intensity (Pm + Pb + Q or PL + Pb + Q).
Maximum stress intensity, allowable stress intensity, and minimum margins of safety for each stress category and each load case are presented in Table 2.6-4 and Table 2.6-6 for each of the cases discussed above. Since all margins of safety are positive, the design criteria are satisfied.
2.6.4.3        Buckling Assessment of the Torispherical Heads The buckling analysis of the torispherical heads is based on the methodology outlined in Paragraph NE-3133.4(e), Torispherical Heads, of the ASME Boiler and Pressure Vessel Code, Section III, Subsection NE. The results from following this methodology are summarized below.
OCV Torispherical Head                  ICV Torispherical Head Parameter                      Upper              Lower              Upper              Lower R                        77.3125            74.1250            74.3750            73.1250 T                          0.25                0.25              0.25                0.25 0.125 A=                            0.00040            0.00042            0.00042            0.00043 (R T )
B6                        5,000              5,000              5,000              5,000 B
Pa =                            16.2                16.9              16.8                17.1 (R T )
The smallest allowable pressure, Pa, is 16.2 psig for the OCV upper head. For an applied external pressure of 14.7 psig, the corresponding buckling margin of safety is:
16.2 MS =          1 = +0.10 14.7 Since the margin of safety in the worst case is positive, it is concluded that none of the OCV or ICV torispherical heads will buckle for an external pressure of 14.7 psig.
2.6.4.4        Buckling Assessment of the Cylindrical Shells The cylindrical portions of the OCV and ICV are evaluated using ASME Boiler and Pressure Vessel Code Case N-284-1 7. Consistent with Regulatory Guide 7.6 philosophy, a factor of 6
Factor B is found from American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section II, Materials, Part D, Properties, Subpart 3, Charts and Tables for Determining the Shell Thickness of Components Under External Pressure, Figure HA-1, Chart for Determining Shell Thickness of Components Under External Pressure When Constructed of Austenitic Steel (18Cr-8Ni, Type 304), 1995 Edition, 1997 Addenda.
Conservatively, the 400 &#xba;F temperature curve is used for each case.
2.6-9
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 safety of 2.0 is applied for NCT buckling evaluations per ASME Code Case N-284-1, corresponding to ASME Code, Service Level A conditions.
Buckling analysis geometry parameters are summarized in Table 2.6-7, and loading parameters are summarized in Table 2.6-8. The cylindrical shell buckling analysis conservatively utilizes an OCV and ICV temperature of 160 &#xba;F, consistent with Section 2.6.1, Heat. The stresses are determined using an external pressure of 14.7 psig. The hoop stress, , axial stress, , and in-plane shear stress, , are found from:
Pr            Pr              Pr
                                    =            =            =
t            2t              4t where P is the applied external pressure of 14.7 psi, r is the mean radius, and t is the cylindrical shell thickness. As shown in Table 2.6-9, since all interaction check parameters are less than 1.0, as required, the design criteria are satisfied.
2.6.5      Vibration By comparing the alternating stresses arising during NCT with the established endurance limits of the HalfPACT packaging materials of construction, the effects of vibration normally incident to transport are shown to be acceptable. These comparisons apply the methodology and limits of NRC Regulatory Guide 7.6. By conservatively comparing NCT stresses with endurance stress limits for an infinite service life, the development of accurate vibratory loading cycles is not required. The vibration evaluation is comprehensively addressed in the following sections.
2.6.5.1      Vibratory Loads Determination ANSI N14.23 8 provides a basis for estimating peak truck trailer vibration inputs. A summary of peak vibratory accelerations for a truck semi-trailer bed with light loads (less than 15 tons) is provided in Table 2 of ANSI N14.23. The component accelerations are given in Table 2 as 1.3g longitudinally, 0.5g laterally, and 2.0g vertically. Three fully loaded HalfPACT packages on a single trailer will exceed the light load limit, but acceleration magnitudes associated with light loads are conservative for heavy loads per Table 2 of ANSI N14.23. The commentary provided within Section 4.2, Package Response, of ANSI N14.23 states that recent tests conducted by Sandia National Laboratories have shown that the truck bed accelerations provide an upper bound on cask (response) accelerations. Based upon these data, conservatively assume the peak acceleration values from Table 2 are applied to the HalfPACT package in a continuously cycling fashion.
The compressive stress in the polyurethane foam for a 2g vertical acceleration is determined by conservatively ignoring the contributory effect of the OCA outer shell and dividing a maximum weight HalfPACT package (18,100 pounds) by the projected area of the packages bottom. The projected area of a HalfPACT package is simply (/4)(94.375)2 = 6,995 in2. Therefore, the compressive stress is (2)(18,100)/6,995 = 5 psi. This stress is negligible compared to the parallel-to-rise compressive strength of 150 psi for polyurethane foam at 160 &#xba;F, as discussed in 7
American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, Division 1, Class MC, Code Case N-284-1, Metal Containment Shell Buckling Design Methods, 1995 Edition, 1997 Addenda.
8 ANSI N14.23, Design Basis for Resistance to Shock and Vibration of Radioactive Material Packages Greater than One Ton in Truck Transport (Draft), 1980, American National Standards Institute, Inc, (ANSI).
2.6-10
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 Section 2.6.1, Heat. Therefore, the remainder of the NCT vibration evaluation addresses only the structural steel portions of the HalfPACT packaging.
2.6.5.2      Calculation of Alternating Stresses The HalfPACT package is a compact right circular cylinder. As such, the stresses developed as a result of transportation vibration become significant only where concentrated in the vicinity of the tie-downs and package interfaces with the transport vehicle. This fact allows the stress analyses of Section 2.5.2, Tie-down Devices, to serve as the basis for derivation of alternating stress estimates.
The analyses of Section 2.5.2, Tie-down Devices, identify three maximum stress locations of importance in the immediate vicinity of the tie-down lugs:
: 1. Tiedown lug weld shear stresses due to tensile tie-down forces. Under a combined set of tie-down forces (i.e., 10g longitudinally, 5g laterally, and 2g vertically), the tie-down lug vertical tensile force is Ftmax = 68,950 pounds. The corresponding tie-down lug weld shear stress is  = 8,997 psi, from Section 2.5.2.2.1, Failure of the Tie-down Lug Welds Due to Shear and Bending Loads. Weld shear stresses associated with unit accelerations (i.e., 1g) are derived from these values, as presented in Table 2.6-10. Under unit horizontal and vertical accelerations, the maximum weld shear stresses are 699 psi and 590 psi, respectively, as shown in Table 2.6-10.
: 2. OCA outer shell compressive membrane stresses due to vertical compressive loads. Under a combined set of tie-down forces (i.e., 10g longitudinally, 5g laterally, and 2g vertically), the OCA outer shell and tie-down lug doubler plate vertical compressive load is Fcmax = 128,901 pounds. The corresponding compressive membrane stress is c = 12,394 psi, from Section 2.5.2.3.1, Bearing Stress in the OCA Outer Shell and Tie-down Lug Doubler Plate. Compressive membrane stresses associated with unit accelerations (i.e., 1g) are derived from these values, as presented in Table 2.6-11. Under unit horizontal and vertical accelerations, the maximum membrane compression stresses are 1,031 psi and 435 psi, respectively, as shown in Table 2.6-11.
: 3. OCA tie-down weldment compressive membrane stresses due to horizontal compressive loads. Under a combined set of tie-down forces (i.e., 10g longitudinally, 5g laterally, and 2g vertically), the OCA tie-down weldment horizontal compressive load is Fh = 202,364 pounds. The corresponding compressive membrane stress is c = 25, 296 psi, from Section 2.5.2.4.1, Bearing Stress in the Tie-down Weldment. Compressive membrane stresses associated with unit accelerations (i.e., 1g) are derived from these values, as presented in Table 2.6-12. Under unit horizontal accelerations, the maximum membrane compression stress is 2,263 psi, as shown in Table 2.6-12.
Alternating stress intensities, Salt, due to 1g unit accelerations are calculated directly from the above values since there are no other measurable stresses acting on the package at the locations considered.
Unit alternating stress intensities at the three evaluated locations are found as shown in Table 2.6-13, making use of the definition of alternating stress intensity as one-half of the range of stress intensity at the location of interest, and the definition of stress intensity as twice the shear stress.
These maximum alternating stress intensity unit values correspond to stresses in the bevel-plus-fillet welds used to attach the tie-down lugs to the tie-down lug doubler plates. A stress concentration factor of four is conservatively applied in accordance with Paragraph C.3.d of 2.6-11
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 Regulatory Guide 7.6. Normalizing the unit values to the peak acceleration estimates given in Section 2.6.5.1, Vibratory Loads Determination, and including the stress concentration factor of four and assuming these worst cases occur at the same location, results in the following conservative estimates of alternating stress intensity associated with the vibratory environments.
For the maximum horizontal alternating stress intensity of 1,132 psi from Table 2.6-13:
Salt = 4(1,132) (1.3) 2 + (0.5) 2 = 6,307 psi and, for the maximum vertical alternating stress intensity of 590 psi from Table 2.6-13:
Salt = 4(590)( 2.0) = 4,720 psi Assuming a simultaneous application of the above alternating stress intensities associated with horizontal and vertical loads yields a maximum alternating stress of 6,307 + 4,720 = 11,027 psi.
2.6.5.3      Stress Limits and Results The permissible alternating stress intensity, Sa, is given by conservatively using the minimum asymptotic value from the design fatigue curves in Table I-9.2.2 of the ASME Boiler and Pressure Vessel Code 9. For design fatigue curve C at 1011 cycles, Sa = 13,600 psi, based on an elastic modulus of 28.3(10)6 psi. This value, when multiplied by the ratio of the elastic modulus at 160 &#xba;F of 27.8(10)6 psi to an elastic modulus at 70 &#xba;F of 28.3(10)6 psi results in an allowable alternating stress intensity amplitude at 160 &#xba;F of:
27.8 Sa = 13,600        = 13,360 psi 28.3 Finally, a conservative estimate of the margin of safety for vibratory effects becomes:
Sa      13,360 MS =        1 =          1 = +0.21 Salt      11,027 2.6.6      Water Spray The materials of construction utilized for the HalfPACT package are such that the water spray test identified in 10 CFR &sect;71.71(c)(6) will have a negligible effect on the package.
2.6.7      Free Drop Since the maximum gross weight of the HalfPACT package is 18,100 pounds, a 3-foot free drop is required per 10 CFR &sect;71.71(c)(7). As discussed in Appendix 2.10.3, Certification Tests, a NCT, 3-foot side drop, aligned over the OCV vent port, was performed on a HalfPACT package certification test unit (CTU) as an initial condition for subsequent hypothetical accident condition (HAC) tests. Leakage rate testing following certification testing demonstrated the ability of the 9
American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, Appendix I, Design Stress Intensity Values, Allowable Stresses, Material Properties, and Design Fatigue Curves, 1995 Edition, 1997 Addenda.
2.6-12
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 HalfPACT package to maintain leaktight (i.e., 1.0 x 10-7 standard cubic centimeters per second (scc/sec), air) sealing integrity. Therefore, the requirements of 10 CFR &sect;71.71(c)(7) are met.
2.6.8      Corner Drop This test does not apply, since the package weight is in excess of 100 kg (220 pounds), and the materials do not include wood or fiberboard, as delineated in 10 CFR &sect;71.71(c)(8).
2.6.9      Compression This test does not apply, since the package weight is in excess of 5,000 kg (11,000 pounds), as delineated in 10 CFR &sect;71.71(c)(9).
2.6.10 Penetration The one-meter (40-inch) drop of a 13-pound, hemispherically-headed, 1-inch diameter, steel cylinder, as delineated in 10 CFR &sect;71.71(c)(10), is of negligible consequence to the HalfPACT package. This is due to the fact that the HalfPACT package is designed to minimize the consequences associated with the much more limiting case of a 40 inch drop of the entire package onto a puncture bar as discussed in Section 2.7.3, Puncture. The 1/4-inch minimum thickness, OCA outer shell, the tie-down lugs and doubler plates, and the vent port and seal test port penetrations are not damaged by the penetration event.
2.6-13
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Table 2.6 Summary of Stress Results for OCA Load Case 1 Stress Intensity (psi)
General          Local      Primary        Primary Primary        Primary    Membrane          plus Membrane Membrane + Bending Secondary Component          Location            (Pm)            (PL)      (Pm/L + Pb) (Pm/L + Pb + Q)
Cylindrical and        19,061                      20,256 OCV Shells                                              -----                        -----
Conical Shells    (Element 329)                (Element 329)
OCV              Crown            13,366          -----      18,739          -----
Upper and Lower                      (Element 339)                (Element 340)
Torispherical                                          28,084                      39,884 Heads            Knuckle              -----                        -----
(Element 337)                (Element 320)
Shell side of the                                                32,358 OCV                                  -----          -----        -----
thickness transition                                              (Node 2010)
Upper and Lower Seal Flanges    Flange side of the                                                20,129 thickness transition                                              (Node 2016)
OCV Locking                                                                        24,493 Any location            -----          -----        -----
Ring                                                                          (Node 3050)
OCA Outer Shell                          9,114                      14,215 Any location                          -----                        -----
and Z-flanges                        (Element 414)                (Element 414)
Maximum Stress Intensity            19,061        28,084        20,256        39,884 20,000        30,000        30,000        60,000 Allowable Stress Intensity (Sm)        (1.5Sm)      (1.5Sm)        (3.0Sm)
Minimum Margin of Safety              +0.05          +0.07        +0.48          +0.50 2.6-14
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Table 2.6 Summary of Stress Results for OCA Load Case 2 Stress Intensity (psi)
General      Local      Primary        Primary Primary    Primary    Membrane          plus Membrane Membrane + Bending Secondary Component          Location            (Pm)        (PL)    (Pm/L + Pb) (Pm/L + Pb + Q)
Cylindrical and                                              20,144 OCV Shells                            -----        -----        -----
Conical Shells                                            (Element 329)
OCV              Crown            -----        -----        -----        18,831 Upper and Lower                                                              (Element 340)
Torispherical                                                                  40,200 Heads            Knuckle            -----        -----        -----
(Element 320)
Shell side of the                                            32,569 OCV                                -----        -----        -----
thickness transition                                        (Node 2010)
Upper and Lower Seal Flanges    Flange side of the                                            20,271 thickness transition                                        (Node 2016)
OCV Locking                                                                    24,503 Any location          -----        -----        -----
Ring                                                                    (Node 3050)
OCA Outer Shell                                                                12,385 Any location          -----        -----        -----
and Z-flanges                                                              (Element 399)
Maximum Stress Intensity            -----        -----        -----        40,200 20,000      30,000      30,000        60,000 Allowable Stress Intensity (Sm)      (1.5Sm)      (1.5Sm)        (3.0Sm)
Minimum Margin of Safety              -----        -----        -----        +0.49 2.6-15
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Table 2.6 Summary of Stress Results for OCA Load Case 3 Stress Intensity (psi)
General      Local      Primary        Primary Primary    Primary    Membrane          plus Membrane Membrane + Bending Secondary Component          Location            (Pm)        (PL)    (Pm/L + Pb) (Pm/L + Pb + Q)
Cylindrical and                                                854 OCV Shells                            -----        -----        -----
Conical Shells                                            (Element 327)
OCV              Crown            -----        -----        -----          538 Upper and Lower                                                              (Element 309)
Torispherical                                                                  1,040 Heads            Knuckle            -----        -----        -----
(Element 323)
Shell side of the                                              450 OCV                                -----        -----        -----
thickness transition                                        (Node 2001)
Upper and Lower Seal Flanges    Flange side of the                                              911 thickness transition                                        (Node 1040)
OCV Locking Any location          -----        -----        -----          0 Ring OCA Outer Shell                                                                  5,772 Any location          -----        -----        -----
and Z-flanges                                                              (Element 393)
Maximum Stress Intensity            -----        -----        -----        5,772 20,000      30,000      30,000        60,000 Allowable Stress Intensity (Sm)      (1.5Sm)      (1.5Sm)        (3.0Sm)
Minimum Margin of Safety              -----        -----        -----        +9.40 2.6-16
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Table 2.6 Summary of Stress Results for OCA Load Case 4 Stress Intensity (psi)
General          Local      Primary        Primary Primary        Primary    Membrane          plus Membrane Membrane + Bending Secondary Component          Location            (Pm)            (PL)      (Pm/L + Pb) (Pm/L + Pb + Q)
Cylindrical and        4,748                        5,087 OCV Shells                                              -----                        -----
Conical Shells    (Element 329)                (Element 329)
OCV              Crown              3,323          -----        4,569          -----
Upper and Lower                      (Element 339)                (Element 340)
Torispherical                                          6,852                        9,641 Heads            Knuckle              -----                        -----
(Element 337)                (Element 320)
Shell side of the                                                  3,507 OCV                                  -----          -----        -----
thickness transition                                              (Node 1016)
Upper and Lower Seal Flanges    Flange side of the                                                  3,741 thickness transition                                              (Node 1164)
OCV Locking                                                                            4 Any location            -----          -----        -----
Ring                                                                          (Node 3181)
OCA Outer Shell                            858                        1,135 Any location                          -----                        -----
and Z-flanges                        (Element 399)                (Element 399)
Maximum Stress Intensity              4,748          6,852        5,087          9,641 20,000        30,000        30,000        60,000 Allowable Stress Intensity (Sm)        (1.5Sm)      (1.5Sm)        (3.0Sm)
Minimum Margin of Safety              +3.21          +3.38        +4.90          +5.22 2.6-17
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Table 2.6 Summary of Stress Results for ICV Load Case 1 Stress Intensity (psi)
General          Local      Primary        Primary Primary        Primary    Membrane          plus Membrane Membrane + Bending Secondary Component          Location            (Pm)            (PL)      (Pm/L + Pb) (Pm/L + Pb + Q)
Cylindrical and        15,251                      22,336 ICV Shells                                            -----                        -----
Conical Shells    (Element 364)                (Element 365)
ICV              Crown            15,242          -----      19,519          -----
Upper and Lower                      (Element 376)                (Element 377)
Torispherical                                          26,968                      38,304 Heads            Knuckle              -----                        -----
(Element 373)                (Element 374)
Shell side of the                                                34,042 ICV                                  -----          -----        -----
thickness transition                                              (Node 2058)
Upper and Lower Seal Flanges    Flange side of the                                                27,922 thickness transition                                              (Node 2053)
ICV Locking                                                                        22,190 Any location            -----          -----        -----
Ring                                                                          (Node 3046)
Maximum Stress Intensity            15,251        26,968        22,336        38,304 20,000        30,000        30,000        60,000 Allowable Stress Intensity (Sm)        (1.5Sm)      (1.5Sm)        (3.0Sm)
Minimum Margin of Safety              +0.31          +0.11        +0.34          +0.57 2.6-18
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Table 2.6 Summary of Stress Results for ICV Load Case 2 Stress Intensity (psi)
General          Local      Primary        Primary Primary        Primary    Membrane          plus Membrane Membrane + Bending Secondary Component          Location            (Pm)            (PL)      (Pm/L + Pb) (Pm/L + Pb + Q)
Cylindrical and        2,363                        2,551 ICV Shells                                            -----                        -----
Conical Shells    (Element 361)                (Element 363)
ICV              Crown              3,635          -----        4,656          -----
Upper and Lower                      (Element 376)                (Element 377)
Torispherical                                          6,382                        9,104 Heads            Knuckle              -----                        -----
(Element 373)                (Element 374)
Shell side of the                                                  2,706 ICV                                  -----          -----        -----
thickness transition                                              (Node 2054)
Upper and Lower Seal Flanges    Flange side of the                                                  3,640 thickness transition                                              (Node 1129)
ICV Locking                                                                            56 Any location            -----          -----        -----
Ring                                                                          (Node 3046)
Maximum Stress Intensity              3,635          6,382        4,656          9,104 20,000        30,000        30,000        60,000 Allowable Stress Intensity (Sm)        (1.5Sm)      (1.5Sm)        (3.0Sm)
Minimum Margin of Safety              +4.50          +3.70        +5.44          +5.59 2.6-19
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 Table 2.6 Buckling Geometry Parameters per Code Case N-284-1 Geometry and Material Input ICV                          OCV Mean Radius, inch                      36.44                        36.91 Shell Thickness, inch                    0.25                          0.188 Length, inch                        36.0                        32.0 Geometry Output (nomenclature consistent with ASME Code Case N-284-1)
R=                              36.44                        36.91 t=                              0.25                          0.188 R/t =                            145.76                      196.85
                =                            36.0                        32.0
                =                            228.94                      231.89 M =                              11.93                        12.16 M =                              75.85                        88.15 M=                              11.93                        12.16 Notes:
The ICV length is conservatively measured from five inches below the top of the lower ICV seal flange (at the beginning of the 1/4-inch wall thickness) to an assumed support point located one-third of the depth of the lower ICV torispherical head below the head-to-shell interface.
The OCV length is conservatively measured from the top of the tapered wall portion (just below the lower OCV seal flange) to an assumed support point located one-third of the depth of the lower OCV torispherical head below the head-to-shell interface.
Table 2.6 Stress Results for 14.7 psig External Pressure ICV                                              OCV Axial Stress,              1,071              Axial Stress,              1,443 Hoop Stress,                2,143              Hoop Stress,              2,886 Shear Stress,                536              Shear Stress,              722 2.6-20
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 Table 2.6 Buckling Summary for 14.7 psig External Pressure Condition                        ICV              OCV            Remarks Capacity Reduction Factors (-1511)
L =        0.2575            0.2575 L =        0.8000            0.8000 L =        0.8000            0.8000 Plasticity Reduction Factors (-1611)
                                  =        0.5877            0.7307
                                  =        1.0000            1.0000
                                =        0.4474            0.5740 Theoretical Buckling Values (-1712.1.1)
C =        0.6050            0.6050 eL =    115,720 psi        85,697 psi Cr =        0.0855            0.0837 eL = reL =      16,354 psi        11,854 psi Ch =        0.0815            0.0798 eL = heL =      15,581 psi        11,302 psi C =        0.2184            0.2162 eL =      41,770 psi        30,615 psi Elastic Interaction Equations (-1713.1.1) xa =      22,237 psi        16,466 psi ha =      9,302 psi        6,748 psi ra =      9,764 psi        7,077 psi a =      24,937 psi        18,278 psi Axial + Hoop  Check (a):            N/A              N/A Axial + Hoop  Check (b):            N/A              N/A Axial + Shear  Check (c):        0.0697            0.1287      <1OK Hoop + Shear  Check (d):          0.3144            0.5873      <1OK Axial + Hoop + Shear  Check (e,a):          N/A              N/A Axial + Hoop + Shear  Check (e,b):          N/A              N/A Inelastic Interaction Equations (-1713.2.1) xc =      13,069 psi        12,032 psi rc =      9,764 psi        7,077 psi c =      11,157 psi        10,492 psi Axial + Hoop  Check (a):          0.3135            0.5841      <1OK Axial + Shear  Check (b):        0.1218            0.1750      <1OK Hoop + Shear  Check (c):          0.3182            0.5873      <1OK 2.6-21
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Table 2.6 Tie-down Lug Weld Shear Stresses Case and          Load Factors                      Load              Shear Stress Orientation              (gs)                    (pounds)                  (psi)
Combined          10(x), 5(y), 2(z)                68,950                  8,997
[102 + 52] = 11.18                59,900                  7,816 Horizontal (unit horizontal of 1g)            (5,358)                  (699) 2.00                        9,050                  1,181 Vertical        (unit vertical of 1g)              (4,025)                  (590)
Table 2.6 OCA Outer Shell Compressive Membrane Stresses Case and          Load Factors                      Load            Membrane Stress Orientation              (gs)                    (pounds)                  (psi)
Combined          10(x), 5(y), 2(z)              128,901                  12,394 2
[10 +  52]  = 11.18              119,851                  11,524 Horizontal (unit horizontal of 1g)            (10,720)                (1,031) 2.00                        9,050                    870 Vertical (unit vertical of 1g)              (4,025)                  (435)
Table 2.6 OCA Tie-down Weldment Compressive Membrane Stresses Case and          Load Factors                      Load            Membrane Stress Orientation              (gs)                    (pounds)                  (psi)
[102 + 52] = 11.18              202,364                  25,296 Horizontal (unit horizontal of 1g)            (18,100)                (2,263)
Table 2.6 Maximum Unit Alternating Stress Intensities Case and Orientation                          Alternating Stress Intensity 2 max  = 699 psi, Horizontal Lug Weld Shear                  Salt =
2      = 590 psi, Vertical max    = 516 psi, Horizontal OCA Shell Compression                Salt =
2      = 218 psi, Vertical max OCA Base Compression                Salt =          = 1,132 psi, Horizontal 2
                                                          = 1,132 psi, Horizontal Maximum Unit Values
                                                          = 590 psi, Vertical 2.6-22
 
HalfPACT Safety Analysis Report              Rev. 9, August 2022 Figure 2.6 OCA Load Case 1, Overall Model 2.6-23
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 2.6 OCA Load Case 1, Seal Region Detail 2.6-24
 
HalfPACT Safety Analysis Report              Rev. 9, August 2022 Figure 2.6 OCA Load Case 2, Overall Model 2.6-25
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 2.6 OCA Load Case 2, Seal Region Detail 2.6-26
 
HalfPACT Safety Analysis Report              Rev. 9, August 2022 Figure 2.6 OCA Load Case 3, Overall Model 2.6-27
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 2.6 OCA Load Case 3, Seal Region Detail 2.6-28
 
HalfPACT Safety Analysis Report              Rev. 9, August 2022 Figure 2.6 OCA Load Case 4, Overall Model 2.6-29
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 2.6 OCA Load Case 4, Seal Region Detail 2.6-30
 
HalfPACT Safety Analysis Report              Rev. 9, August 2022 Figure 2.6 ICV Load Case 1, Overall Model 2.6-31
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 2.6 ICV Load Case 1, Seal Region Detail 2.6-32
 
HalfPACT Safety Analysis Report                Rev. 9, August 2022 Figure 2.6 ICV Load Case 2, Overall Model 2.6-33
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 2.6 ICV Load Case 2, Seal Region Detail 2.6-34
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 2.7 Hypothetical Accident Conditions The HalfPACT package, when subjected to the sequence of hypothetical accident condition (HAC) tests specified in 10 CFR &sect;71.73 1, subsequent to the sequence of normal conditions of transport (NCT) tests specified in 10 CFR &sect;71.71, is shown to meet the performance requirements specified in Subpart E of 10 CFR 71. As indicated in the introduction to Chapter 2.0, Structural Evaluation, with the exception of the immersion test, the primary proof of performance for the HAC tests is via the use of full scale testing. In particular, free drop, puncture, and fire testing of both a HalfPACT engineering test unit (ETU), and a HalfPACT certification test unit (CTU) confirms that both the inner containment vessel (ICV) and outer containment (now confinement) vessel (OCV) boundaries remained leaktight after a worst case HAC sequence. Observations from testing of the ETU and CTU also confirm the conservative nature of deformed geometry assumptions used in the criticality assessment provided Chapter 6.0, Criticality Evaluation, respectively.
Test results are summarized in Section 2.7.8, Summary of Damage, with details provided in Appendix 2.10.3, Certification Tests. Immersion is addressed by analysis, employing acceptance criteria consistent with NRC Regulatory Guide 7.6 2.
For the analytic assessments performed within this section, properties for Type 304 stainless steel are based on data from Table 2.3-1 from Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations). Similarly, the bounding values for the compressive strength of polyurethane foam are based on data from Table 2.3-2 from Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations. Polyurethane foam compressive strength is further adjusted +/-15% to account for manufacturing tolerance. At elevated HAC temperatures (i.e., 160 &#xba;F), the nominal compressive strength is reduced 25% for elevated temperature effects and reduced 15% for manufacturing tolerance. At reduced HAC temperatures (i.e., -20 &#xba;F), the nominal compressive strength is increased 40% for reduced temperature effects and increased 15% for manufacturing tolerance.
Properties of Type 304 stainless steel and polyurethane foam, as applied to analytic assessments within this section, are summarized below.
Material Property Value (psi)
Material Property                      -20 &#xba;F          70 &#xba;F          160 &#xba;F        Reference Type 304 Stainless Steel Elastic Modulus, E                  28.8 x 106      28.3 x 106      27.8 x 106 Design Stress Intensity, Sm                20,000          20,000          20,000        Table 2.3-1 Yield Strength, Sm                    30,000          30,000          27,000 Polyurethane Foam Compressive Strength Parallel-to-Rise Direction, c                378            235              150 Table 2.3-2 Perpendicular-to-Rise Direction, c              314            195              124 1
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 U. S. Nuclear Regulatory Commission, Regulatory Guide 7.6, Design Criteria for the Structural Analysis of Shipping Cask Containment Vessels, Revision 1, March 1978.
2.7-1
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 2.7.1      Free Drop Subpart F of 10 CFR 71 requires performing a free drop test in accordance with the requirements of 10 CFR &sect;71.73(c)(1). The free drop test involves performing a 30-foot, HAC free drop onto a flat, essentially unyielding, horizontal surface, with the package striking the surface in a position (orientation) for which maximum damage is expected. The ability of the HalfPACT package to adequately withstand this specified free drop condition is demonstrated via testing of two full scale, HalfPACT test packages.
2.7.1.1      Technical Basis for the Free Drop Tests To properly select a worst case package orientation for the 30-foot free drop event, items that could potentially compromise containment integrity, shielding integrity, and/or criticality safety of the HalfPACT package must be clearly identified. For the HalfPACT package design, the foremost item to be addressed is the ability of the containment seals to remain leaktight.
Shielding integrity is not a controlling case for the reasons described in Chapter 5.0, Shielding Evaluation. Criticality safety is conservatively evaluated based on measured physical damage to the outer containment (now confinement) assembly (OCA) shells and polyurethane foam from certification testing, as described in Chapter 6.0, Criticality Evaluation.
The leaktight capability of the containment seals may be compromised by two methods: 1) as a result of excessive sealing surface deformation leading to reduced seal compression, and/or 2) as a result of thermal degradation of the seal material itself in a subsequent fire event. Importantly, these methods require significant impact damage to the surrounding polyurethane foam. In other words, a significant reduction in polyurethane foam thickness or a gross exposure of the foam through splits or punctures in the OCA outer shell would have to occur near the main O-ring seal or vent port seal region.
Additional items for consideration include the possibility of separating the OCA lid from the OCA body (or significantly opening up the nominal 1/2-inch gap which exists between the upper and lower Z-flanges at the lid to body interface), and buckling of the OCV or ICV from a bottom end drop.
For the above reasons, testing must include impact orientations that affect the upper end of the HalfPACT package, with particularly emphasis in the closure region. Loads and resultant deformations occurring over the lower half of the package does not present a worst case regarding the leaktight capability of the seals or the separation of the OCA lid from the OCA body. However, as discussed above, a bottom end drop is of interest regarding the possibility of shell buckling because of the high axial acceleration forces imparted to the package.
In addition to package orientation, initial test conditions such as temperatures and pressures must be selected to complete the definition of the conditions existing at the time of a HAC free drop.
In general, higher temperatures at the time of a drop test result in greater deformations and lesser acceleration loads than do lower temperatures. This is due primarily to the modest temperature sensitivity of the energy absorbing polyurethane foam used within the HalfPACT OCA.
Appendix 2.10.3, Certification Tests, provides a comprehensive report of the certification test process and results. Discussions specific to the configuration of the test units are provided in Appendix 2.10.3.4, Test Unit Description. Discussions specific to orientations of the test units for free drop, puncture, and fire tests, including initial test conditions, are provided in Appendix 2.7-2
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 2.10.3.5, Technical Basis for Tests. Discussions specific to test sequences for selected tests for the test units is provided in Appendix 2.10.3.6, Test Sequence for Selected Free Drop, Puncture Drop, and Fire Tests.
2.7.1.2        Test Sequence for the Selected Tests Based on the above general discussions, the ETU was tested for three specific, HAC 30-foot free drop conditions for inclusion in the engineering test program. Similarly, based on results from ETU testing, the CTU was tested for two specific, HAC 30-foot free drop conditions for inclusion in the certification test program. Although only a single worst case 30-foot drop is required by 10 CFR &sect;71.73(c)(1), multiple tests were performed to ensure that the most vulnerable package features were subjected to worst case loads and deformations. The specific conditions selected for ETU and CTU free drop testing are summarized in Table 2.7-1 and Table 2.7-2, respectively.
2.7.1.3        Summary of Results from the Free Drop Tests Successful HAC free drop testing of the ETU and CTU indicates that the various HalfPACT packaging design features are adequately designed to withstand the HAC 30-foot free drop event.
The most important result of the testing program was the demonstrated ability of the OCV and ICV to remain leaktight 3. Significant results of free drop testing common to both test units are as follows:
* There was no evidence of buckling of either the ICV or OCV shells. Modest damage to the containment vessel shells did occur, an amount somewhat in excess of what was reported in the TRUPACT-II package SAR 4. However, it is clear that the damage noted for the HalfPACT package corresponds to the much heavier payload drums interaction with the packaging wall.
* No excessive distortion of the seal flange regions occurred for either the ICV or OCV, although some permanent deformation was noted.
* There was no rupture of the 3/8-inch thick, OCA outer shell.
* Observed permanent deformations of the HalfPACT packaging were less than those assumed for the criticality evaluation.
A comprehensive summary of free drop test results is provided in Appendix 2.10.3.7, Test Results.
2.7.2        Crush Subpart F of 10 CFR 71 requires performing a dynamic crush test in accordance with the requirements of 10 CFR &sect;71.73(c)(2). Since the HalfPACT package weight exceeds 1,100 pounds, the dynamic crush test is not required.
2.7.3        Puncture Subpart F of 10 CFR 71 requires performing a puncture test in accordance with the requirements of 10 CFR &sect;71.73(c)(3). The puncture test involves a 40-inch free drop of a package onto the 3
Leaktight is a leakage rate not exceeding 1 x 10-7 standard cubic centimeters per second (scc/sec), air, as defined in ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
4 U.S. Department of Energy (DOE), Safety Analysis Report for the TRUPACT-II Shipping Package, USNRC Certificate of Compliance 71-9218, U.S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico.
2.7-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 upper end of a solid, vertical, cylindrical, mild steel bar mounted on an essentially unyielding, horizontal surface. The bar must be six inches in diameter, with the top surface horizontal and its edge rounded to a radius of not more than 1/4 inch. The package is to be oriented in a position for which maximum damage will occur. The minimum length of the bar is to be eight inches. The ability of the HalfPACT package to adequately withstand this specified puncture drop condition is demonstrated via testing of two full scale, HalfPACT test packages.
2.7.3.1      Technical Basis for the Puncture Drop Tests To properly select a worst case package orientation for the puncture drop event, items that could potentially compromise containment integrity, shielding integrity, and/or criticality safety of the HalfPACT package must be clearly identified. For the HalfPACT package design, the foremost item to be addressed is the ability of the containment seals to remain leaktight. Shielding integrity is not a controlling case for the reasons described in Chapter 5.0, Shielding Evaluation.
Criticality safety is conservatively evaluated based on measured physical damage to the OCA shells and polyurethane foam from certification testing, as described in Chapter 6.0, Criticality Evaluation.
For the HalfPACT design, the primary item to be addressed for the puncture drop is the ability of the containment seals to remain leaktight. The leaktight capability of the O-ring seals would be most easily compromised by imposing gross deformations in the sealing region. These types of deformations are of concern from a mechanical viewpoint (i.e., leakage caused by excessive relative movement of the sealing surfaces). In addition, such deformations are of concern from a thermal viewpoint (i.e., leakage caused by thermal degradation of the butyl O-ring seals in a subsequent fire). Importantly, for mechanical damage to occur in the seal regions, the puncture event would have to result in a gross rupturing of the OCA outer shell near the O-ring seals. This could allow the puncture bar to reach and directly impact the OCA seal flanges or locking ring.
Similarly, for thermal degradation of the butyl O-ring seals to occur in a subsequent fire, damage to the OCA outer shell near the O-ring seals would again have to occur as a result of the puncture event. Another item associated with the puncture event is the possibility of the puncture bar penetrating the OCA outer shell and rupturing the OCV. Puncture is most likely to occur if the center of gravity of the package is directly in-line with the puncture bar, and the surface of the package is oriented at an angle to the bar axis. If the center of gravity of the package is not in-line with the puncture bar, puncture is less likely since package potential energy is transformed into rotational kinetic energy. Puncture is also more likely if the puncture bar impacts the package surface adjacent to a package shell weld seam. Observations from prior testing indicate that impacts with the package surface, normal to the axis of the puncture bar, will not lead to penetration of the OCA exterior shell. This is the primary reason for utilizing a torispherical head for the OCA lid. The torispherical head results in the puncture bar being oriented normal to the package surface when the center of gravity of the package is directly over the puncture bar.
Further, a 3/8-inch thick OCA outer shell is used near the closure region to ensure that no puncture will occur in this region, regardless of impact angle.
In addition to package orientation, initial test conditions such as temperatures and pressures must be selected to complete the definition of the conditions existing at the time of a HAC puncture drop. In general, higher temperatures at the time of a puncture test result in greater deformations and lesser acceleration loads than do lower temperatures. This is due primarily to the modest temperature sensitivity of the polyurethane foam used within the HalfPACT OCA.
2.7-4
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 Appendix 2.10.3, Certification Tests, provides a comprehensive report of the certification test process and results. Discussions specific to the configuration of the test units are provided in Appendix 2.10.3.4, Test Unit Description. Discussions specific to orientations of the test units for free drop, puncture, and fire tests, including initial test conditions, are provided in Appendix 2.10.3.5, Technical Basis for Tests. Discussions specific to test sequences for selected tests for the test units is provided in Appendix 2.10.3.6, Test Sequence for Selected Free Drop, Puncture Drop, and Fire Tests.
2.7.3.2      Test Sequence for the Selected Tests Based on the above general discussions, the ETU was specifically tested for four HAC puncture drop conditions as part of the engineering test program. Similarly, based on results from ETU testing, the CTU was specifically tested for three HAC puncture drop conditions as part of the certification test program. Although only a single worst case puncture drop is required by 10 CFR &sect;71.73(c)(3),
multiple tests were performed to ensure that the most vulnerable package features were subjected to worst case loads and deformations. The specific conditions selected for ETU and CTU puncture drop testing are summarized in Table 2.7-1 and Table 2.7-2, respectively.
2.7.3.3      Summary of Results from the Puncture Drop Tests Successful HAC puncture drop testing of the ETU and CTU indicates that the various HalfPACT packaging design features are adequately designed to withstand the HAC puncture drop event.
As with the free drop test, the most important result of the testing program was the demonstrated ability of the OCV and ICV to remain leaktight. Significant results of puncture drop testing common to both test units are as follows:
* Besides the obvious permanent damage to the OCA outer shell at the location of the various puncture bar impacts, there was evidence of some permanent deformation of the OCV shell.
The most significant damage occurred at the OCV vent port fitting during testing of the CTU.
The cumulative effects of the NCT and HAC free drops, and the subsequent puncture drop caused successively greater permanent deformation to the region adjacent to the vent port fitting. A crack was noted in the inner weld of the CTUs OCV vent port fitting, but not in the outer weld of the OCV vent port fitting. Subsequent helium leak testing determined that OCV containment integrity was maintained. Although essentially identical in configuration, the ETU did not have a similarly cracked weld. See Appendix 2.10.3.7.2.8, CTU Post-Test Disassembly, for additional discussion regarding this result.
* Penetration of the OCA outer shell occurred below the 3/8-to-1/4-inch thick, OCA outer shell weld during testing of the ETU. The same test, repeated for certification testing, did not reproduce the hole. This result was due to lengthening the 3/8-inch thick, OCA outer shell from 12 to 18 inches, correspondingly changing the impact angle sufficiently to prevent penetration through the adjacent 1/4-inch thick shell.
* There was no rupture of the 3/8-inch thick, OCA outer shell. However, for both test units (ETU and CTU) a linear tear occurred along the weld at the 3/8-to-1/4-inch shell transition in the OCA body outer shell.
A comprehensive summary of test results is provided in Appendix 2.10.3.7, Test Results.
2.7-5
 
HalfPACT Safety Analysis Report                                                            Rev. 9, August 2022 2.7.4      Thermal Subpart F of 10 CFR 71 requires performing a thermal test in accordance with the requirements of 10 CFR &sect;71.73(c)(4). To demonstrate the performance capabilities of the HalfPACT package when subjected to the HAC thermal test specified in 10 CFR &sect;71.73(c)(4), two full scale prototype test units were burned in two, separate, fully engulfing pool fires. Each test unit was subjected to a variety of HAC, 30-foot free drop and puncture tests prior to being burned, as discussed in Section 2.7.1, Free Drop, and Section 2.7.3, Puncture. Testing of the engineering test unit (ETU) preceded testing of the certification test unit (CTU), and was used for the purpose of accessing the effect of the various HAC tests. Planning to determine a worst case certification test scenario for the CTU was based ETU responses to a comprehensive set of HAC tests. Further, while the CTU had passive, temperature indicating labels to report post-test temperatures, the ETU did not. Thus, information reported herein considers only test results of the CTU.
As discussed further in Appendix 2.10.3, Certification Tests, the CTU was oriented horizontally in a stand a distance one meter above the fuel per the requirements of 10 CFR &sect;71.73(c)(4). The CTU was oriented circumferentially at an angle of 305&#xba; to position the damage from Drops 1, 2, and 4 (0&#xba;; aligned with the vent ports) and the damage from Drop 5 (250&#xba;) a distance 1/2 meter above the lowest part of the package while on the stand (i.e., 11/2 meters above the fuel 5). This particular arrangement put the maximum drop damage in the hottest part of the fire.
During the HAC fire test, the average wind speed was determined to be approximately 4 miles per hour. As discussed in Appendix 2.10.3, Certification Tests, the duration of the fully engulfing, HAC fire test was approximately 33 minutes, and the ambient air temperature was 51 &#xba;F.
2.7.4.1      Summary of Pressures and Temperatures Package pressures and temperatures due to the HAC fire test are presented in Appendix 2.10.3, Certification Tests. Detailed discussions regarding measured temperatures are provided in Section 3.5.3, Package Temperatures. Detailed discussions regarding calculated pressures are provided in Section 3.5.4, Maximum Internal Pressure.
2.7.4.1.1      Summary of Temperatures No active temperature measuring devices were employed prior to, during, or following the HAC fire test. Further, measurement of the OCA outer shell temperature does not represent the OCV or ICV temperatures due to the large internal mass and thick, thermally insulating foam used within the OCA. As discussed in Section 3.1.1, Packaging, the temperatures of the OCV, ICV, and payload are effectively decoupled from the OCA outer shell and polyurethane foam for short term thermal transients. Instead, the initial temperature of CTU No. 1 may be estimated based on the ambient temperature of the Sandia National Laboratory testing facilities in the six weeks prior to 5
M. E. Schneider and L. A. Kent, Measurements of Gas Velocities and Temperatures in a Large Open Pool Fire, Sandia National Laboratories (reprinted from Heat and Mass Transfer in Fire, A. K. Kulkarni and Y. Jaluria, Editors, HTD-Vol. 73 (Book No. H00392), American Society of Mechanical Engineers). Figure 3 shows that maximum temperatures occur at an elevation approximately 2.3 meters above the pool floor. The pool was initially filled with water and fuel to a level of 0.814 meters. The maximum temperatures therefore occur approximately 11/2 meters above the level of the fuel, i.e., 1/2 meter above the lowest part of the package when set one meter above the fuel source per the requirements of 10 CFR &sect;71.73(c)(4).
2.7-6
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 the HAC fire test 6. Climatological data for Albuquerque, New Mexico, during the month of March and first two weeks of April 1998 shows an average temperature of 48 &#xba;F for those six weeks. Thus, when adjusting for the elevation difference between the testing facilities and Albuquerque, the initial temperature for HAC fire testing is taken as 43 &#xba;F.
Following completion of fire testing, the maximum measured OCV seal region temperature was 200 &#xba;F. Upwardly adjusting for the lower, pre-fire starting temperature by 90 &#xba;F results in a projected maximum OCV seal region temperature of 290 &#xba;F. The maximum measured ICV seal region temperature was 110 &#xba;F. Also, upwardly adjusting for the lower, pre-fire starting temperature by 90 &#xba;F results in a projected maximum ICV seal region temperature of 200 &#xba;F.
2.7.4.1.2      Summary of Pressures The maximum internal pressure for the ICV is conservatively determined by assuming the air temperature within the ICV is at the maximum seal temperature of 200 &#xba;F. The ICV pressure increase, PICV, using an initial maximum ICV wall temperature of 154 &#xba;F (from Table 3.4-1) at an initial pressure equal to the MNOP of 50 psig (64.7 psia), is determined using ideal gas relationships:
P1 P2              P154  F  P200  F                          T200  F
                        =                      =              P200  F = P154  F T1 T2              T154  F  T200  F                          T 154 F 200 + 460 P200  F = 64.7                = 69.5 psia (54.8 psig) 154 + 460 PICV = 54.8  50.0 = 4.8 psig Thus, the maximum internal pressure for the ICV for HAC is 54.8 psig, resulting in a net pressure increase of 4.8 psig.
The maximum internal pressure for the OCV is conservatively determined by assuming the air temperature within the OCV, 245 &#xba;F, is the average of the maximum ICV and OCV seal temperatures of 200 &#xba;F and 290 &#xba;F, respectively. The initial air temperature within the OCV, 152 &#xba;F, is the average of the maximum OCV and ICV wall temperatures of 150 &#xba;F and 154 &#xba;F, respectively (from Table 3.4-1). The OCV pressure increase, POCV, using at an initial pressure equal to the MNOP of 50 psig (64.7 psia), is determined using ideal gas relationships:
P1 P2              P152  F  P245  F                          T245  F
                        =                      =              P245  F = P152  F T1 T2              T152  F  T245  F                          T 152 F 245 + 460 P245  F = 64.7                = 74.5 psia (59.8 psig) 152 + 460 P = 59.8  50.0 = 9.8 psig 6
CTU No. 1 was located at Sandia National Laboratories Coyote Canyon drop test facility for the month of March, 1998, and the Lurance Canyon burn facility for the first two weeks of April, 1998. CTU No. 1 was burned on April 14, 1998. The elevation difference between the two test facilities and the city of Albuquerque results in an average ambient temperature approximately 5 &#xba;F cooler than Albuquerque.
2.7-7
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 Thus, the maximum internal pressure for the OCV for HAC is 59.8 psig, resulting in a net pressure increase of 9.8 psig.
2.7.4.2    Differential Thermal Expansion Fire testing of two, full scale HalfPACT prototypes indicate that the effects associated with differential thermal expansion of the various packaging components are negligible. Subsequent to all NCT and HAC free drop, puncture drop, and fire tests, comprehensive helium leak testing of both the ICV and OCV demonstrated that differential thermal expansion does not affect the capability to remain leaktight.
2.7.4.3      Stress Calculations As shown in Section 2.7.4.1.2, Summary of Pressures, the internal pressure within the ICV increases 4.8 psig (+10%), and within the OCV increases 9.8 psig (+20%) due to the HAC fire test. Pressure stresses due to the HAC fire test corresponding increase a maximum of 20%.
With reference to Table 2.1-1 in Section 2.1.2.1.1, Containment Structure (ICV), the HAC allowable stress intensity for general primary membrane stresses (applicable to pressure loads) is 240% of the NCT allowable stress intensity. Therefore, a HAC pressure stress increase of 20%
will not exceed the HAC allowable stresses. Further, the pressure stresses in conjunction with stresses associated with differential thermal expansion are limited to an acceptable level since both the ICV and OCV were shown to be leaktight after all NCT and HAC free drop, puncture drop, and fire tests (see Appendix 2.10.3.7, Test Results).
2.7.4.4    Comparison with Allowable Stresses As discussed in Section 2.7.4.3, Stress Calculations, further quantification of stresses in the various HalfPACT package components is not required.
2.7.5      Immersion - Fissile Material Subpart F of 10 CFR 71 requires performing an immersion test for fissile material packages in accordance with the requirements of 10 CFR &sect;71.73(c)(5). The criticality evaluation presented in Chapter 6.0, Criticality Evaluation, assumes optimum hydrogeneous moderation of the contents, thereby conservatively addressing the effects and consequences of water in-leakage.
2.7.6      Immersion - All Packages Subpart F of 10 CFR 71 requires performing an immersion test for all packages in accordance with the requirements of 10 CFR &sect;71.73(c)(6). For the HalfPACT package design, the effect of a 21 psig external pressure due to immersion in 50 feet of water is applied to the ICV and OCV.
The external pressure induces small compressive stresses in the ICV and OCV that are limited by stability (buckling) requirements. Buckling assessments are performed for the OCV and ICV in Section 2.7.6.1, Buckling Assessment of the Torispherical Heads, and Section 2.7.6.2, Buckling Assessment of the Cylindrical Shells.
2.7-8
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 2.7.6.1        Buckling Assessment of the Torispherical Heads The buckling analysis of the torispherical heads is based on the methodology outlined in Paragraph NE-3133.4(e), Torispherical Heads, of the ASME Boiler and Pressure Vessel Code, Section III 7, Subsection NE. Since the external pressure loading due to immersion may be classified as Level D, the allowable buckling stress and, therefore, the allowable pressure, can be increased by 150%
per paragraph NE-3222.2. The results from following this methodology are summarized below.
OCV Torispherical Head                  ICV Torispherical Head Parameter                      Upper              Lower              Upper              Lower R                        77.3125            74.1250            74.3750            73.1250 T                          0.25                0.25              0.25                0.25 0.125 A=                            0.00040            0.00042            0.00042            0.00043 (R T )
B8                        5,000              5,000              5,000              5,000 (1.5)B Pa =                            24.3                25.3              25.2                25.6 (R T )
The smallest allowable pressure, Pa, is 24.3 psig for the OCV upper head. For an applied external pressure of 21 psig, the corresponding buckling margin of safety is:
24.3 MS =          1 = +0.16 21 Since the margin of safety in the worst case is positive, it is concluded that none of the OCV or ICV torispherical heads will buckle for an external pressure of 21 psig.
2.7.6.2        Buckling Assessment of the Cylindrical Shells The cylindrical portions of the OCV and ICV are evaluated using ASME Boiler and Pressure Vessel Code Case N-284-1 9. Consistent with Regulatory Guide 7.6 philosophy, a factor of safety of 1.34 is applied for HAC buckling evaluations per ASME Code Case N-284-1, corresponding to ASME Code, Service Level D conditions.
7 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, 1995 Edition, 1997 Addenda.
8 Factor B is found from American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section II, Materials, Part D, Properties, Subpart 3, Charts and Tables for Determining the Shell Thickness of Components Under External Pressure, Figure HA-1, Chart for Determining Shell Thickness of Components Under External Pressure When Constructed of Austenitic Steel (18Cr-8Ni, Type 304), 1995 Edition, 1997 Addenda.
Conservatively, the 400 &#xba;F temperature curve is used for each case.
9 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, Division 1, Class MC, Code Case N-284-1, Metal Containment Shell Buckling Design Methods, 1995 Edition, 1997 Addenda.
2.7-9
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Buckling analysis geometry parameters are summarized in Table 2.7-3, and loading parameters are summarized in Table 2.7-4. The cylindrical shell buckling analysis conservatively utilizes an OCV and ICV temperature of 160 &#xba;F, consistent with Section 2.6.1, Heat. The stresses are determined using an external pressure of 21 psig. The hoop stress, , axial stress, , and in-plane shear stress, , are found from:
Pr              Pr              Pr
                              =              =            =
t              2t              4t where P is the applied external pressure of 21 psi, r is the mean radius, and t is the cylindrical shell thickness. As shown in Table 2.7-5, since all interaction check parameters are less than 1.0, as required, the design criteria are satisfied.
2.7.7      Deep Water Immersion Test Subpart E of 10 CFR 71 requires performing a deep water immersion test in accordance with 10 CFR &sect;71.61. Since the HalfPACT does not transport payloads with an activity of greater than 105 A2, this requirement does not apply.
2.7.8      Summary of Damage As discussed in the previous sections, the cumulative damaging effects of free drop, puncture drop, and fire tests were satisfactorily withstood by the HalfPACT packaging during both engineering and certification testing. Subsequent helium leak testing confirmed that containment integrity was maintained throughout the test series. Therefore, the requirements of 10 CFR
&sect;71.73 have been adequately met.
2.7-10
 
HalfPACT Safety Analysis Report                                                                          Rev. 9, August 2022 Table 2.7 Summary of HalfPACT Engineering Test Unit (ETU) Tests and Results Test Unit Angular Orientation Test                                                  Axial      Circumferential No.              Test Description              (0&#xba; = horizontal) (0&#xba; = vent ports)                Remarks NCT, 3-foot side drop opposite the OCV                                        NCT impact in region expected to produce 1                                                    0&#xba;              200&#xba; vent and seal test ports                                                      worst case cumulative damage to package.
HAC, 30-foot side drop opposite the OCV                                        HAC impact in region expected to produce 2                                                    0&#xba;              200&#xba; vent and seal test ports                                                      worst case cumulative damage to package.
3  NCT, 3-foot side drop on the OCV vent port        0&#xba;                0&#xba;        NCT impact in OCV vent port region.
HAC, 30-foot side drop on the OCV vent 4                                                    0&#xba;                0&#xba;        HAC impact in OCV vent port region.
port NCT, 3-foot center-of-gravity-over-corner                                      NCT impact at location not tested during 5                                                    43&#xba;              110&#xba; drop between tie-down doubler plates                                          previous TRUPACT-II certification tests.
HAC, 30-foot center-of-gravity-over-corner                                    HAC impact at location not tested during 6                                                    43&#xba;              110&#xba; drop between tie-down doubler plates                                          previous TRUPACT-II certification tests.
HAC, puncture drop at the 1/4-to-3/8,                                          Attempt to cause hole in shell below 1/4-7                                                    20&#xba;              200&#xba; OCA body shell weld (below weld)                                              to-3/8, OCA body shell weld.
Puncture in region expected to produce 8  HAC, puncture drop on OCV vent port                1&#xba;                0&#xba; worst case cumulative damage to package.
9  HAC, puncture drop at Test 6 damage              43&#xba;              110&#xba;        Attempt to cause hole in existing damage.
HAC, puncture drop at the 1/4-to-3/8,                                          Attempt to cause linear tear in 1/4-to-3/8, 10                                                    9&#xba;              290&#xba; OCA body shell weld (above weld)                                              OCA body shell weld.
Circumferential orientation places damage 11  HAC, fire test                                    0&#xba;              145&#xba; from Tests 4 and 8 in hottest part of fire.
2.7-11
 
HalfPACT Safety Analysis Report                                                                              Rev. 9, August 2022 Table 2.7 Summary of Selected Certification Test Unit (CTU) Tests Test Unit Angular Orientation Test                                                    Axial      Circumferential No.              Test Description                (0&#xba; = horizontal) (0&#xba; = vent ports)                  Remarks NCT impact in region expected to produce 1    NCT, 3-foot side drop on the OCV vent port          0&#xba;                0&#xba; worst case cumulative damage to package.
HAC, 30-foot side drop on the OCV vent                                          HAC impact in region expected to produce 2                                                        0&#xba;                0&#xba; port                                                                            worst case cumulative damage to package.
HAC, 30-foot, 5&#xba; corner drop on the OCA                                          Drop orientation producing maximum load 3                                                        5&#xba;            1471/2&#xba; top knuckle, slapdown on the tiedown lug                                        on closure region.
Puncture in region expected to produce 4    HAC, puncture drop on the OCV vent port            11/2&#xba;                0&#xba; worst case cumulative damage to package.
HAC, puncture drop at the 1/4-to-3/8,                                            Attempt to cause hole in shell below 1/4-5                                                        16&#xba;              110&#xba; OCA body shell weld (below weld)                                                to-3/8, OCA body shell weld.
HAC, puncture drop at the 1/4-to-3/8,                                            Attempt to cause linear tear in 1/4-to-3/8, 6                                                        23&#xba;              250&#xba; OCA body shell weld (above weld)                                                OCA body shell weld.
55&#xba; or 305&#xba;    Circumferential orientation based on results 7    HAC, fire test                                      0&#xba; (max damage)    of Tests 5 and 6.
Notes:
The 55&#xba; or 305&#xba; circumferential orientation is downward; package bottom is one meter above the fuel surface.
2.7-12
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 Table 2.7 Buckling Geometry Parameters per Code Case N-284-1 Geometry and Material Input ICV                          OCV Mean Radius, inch                      36.44                        36.91 Shell Thickness, inch                    0.25                          0.188 Length, inch                        36.0                        32.0 Geometry Output (nomenclature consistent with ASME Code Case N-284-1)
R=                              36.44                        36.91 t=                              0.25                          0.188 R/t =                            145.76                      196.85
                =                            36.0                        32.0
                =                            228.94                      231.89 M =                              11.93                        12.16 M =                              75.85                        88.15 M=                              11.93                        12.16 Notes:
The ICV length is conservatively measured from five inches below the top of the lower ICV seal flange (at the beginning of the 1/4-inch wall thickness) to an assumed support point located one-third of the depth of the lower ICV torispherical head below the head-to-shell interface.
The OCV length is conservatively measured from the top of the tapered wall portion (just below the lower OCV seal flange) to an assumed support point located one-third of the depth of the lower OCV torispherical head below the head-to-shell interface.
Table 2.7 Stress Results for 21 psig External Pressure ICV                                              OCV Axial Stress,              1,530              Axial Stress,              2,067 Hoop Stress,                3,061              Hoop Stress,              4,133 Shear Stress,                765              Shear Stress,              1,031 2.7-13
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 Table 2.7 Buckling Summary for 21 psig External Pressure Condition                        ICV              OCV            Remarks Capacity Reduction Factors (-1511)
L =        0.2575            0.2575 L =        0.8000            0.8000 L =        0.8000            0.8000 Plasticity Reduction Factors (-1611)
                                  =        0.5877            0.7307
                                  =        1.0000            1.0000
                                =        0.4474            0.5740 Theoretical Buckling Values (-1712.1.1)
C =        0.6050            0.6050 eL =    115,720 psi        85,687 psi Cr =        0.0855            0.0837 eL = reL =      16,354 psi        11,854 psi Ch =        0.0815            0.0798 eL = heL =      15,581 psi        11,302 psi C =        0.2184            0.2162 eL =      41,770 psi        30,611 psi Elastic Interaction Equations (-1713.1.1) xa =      14,899 psi        11,032 psi ha =      6,232 psi        4,521 psi ra =      6,542 psi        4,742 psi a =      16,708 psi        12,246 psi Axial + Hoop  Check (a):            N/A              N/A Axial + Hoop  Check (b):            N/A              N/A Axial + Shear  Check (c):        0.0730            0.1343      <1OK Hoop + Shear  Check (d):          0.3290            0.6121      <1OK Axial + Hoop + Shear  Check (e,a):          N/A              N/A Axial + Hoop + Shear  Check (e,b):          N/A              N/A Inelastic Interaction Equations (-1713.2.1) xc =      8,756 psi        8,061 psi rc =      6,542 psi        4,742 psi c =      7,475 psi        7,029 psi Axial + Hoop  Check (a):          0.3276            0.6086      <1OK Axial + Shear  Check (b):        0.1282            0.1896      <1OK Hoop + Shear  Check (c):          0.3322            0.6192      <1OK 2.7-14
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 2.8 Special Form This section does not apply for the HalfPACT package, since special form is not claimed.
2.8-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.8-2
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 2.9 Fuel Rods This section does not apply for the HalfPACT package, since fuel rods are not included as an approved payload configuration.
2.9-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.9-2
 
HalfPACT Safety Analysis Report                  Rev. 9, August 2022 2.10 Appendices 2.10.1 Finite Element Analysis (FEA) Models 2.10.2 Elastomer O-ring Seal Performance Tests 2.10.3 Certification Tests 2.10-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.10-2
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 2.10.1 Finite Element Analysis (FEA) Models 2.10.1.1 Outer Confinement Assembly (OCA) Structural Analysis Finite element analyses (FEA) are performed on the OCA structure to determine the stress states of the various components under normal conditions of transport (NCT) loads. The FEA analyses are performed using ANSYS 5.3 1. The OCA FEA model is comprised of six separate major structural components, modeled as shown in Figure 2.10.1-1:
* upper OCV seal flange
* OCV shells
* lower OCV seal flange
* OCA shells and Z-flanges
* OCV locking ring
* polyurethane foam The lower and upper seal flanges, locking ring and polyurethane foam are modeled using 2-D, isoparametric solid elements (PLANE42). The quadrilateral elements are defined by four nodal points (a triangular element may be formed by defining duplicate the 3rd and 4th node numbers),
each having two degrees of freedom: translations in the nodal x-direction (radial) and y-direction (axial).
The upper and lower OCA shells (OCA lid and body shells, respectively) are modeled using 2-D, axisymmetric conical shell elements (SHELL51). The lineal elements are defined by two nodal points, each having three degrees of freedom: translations in the nodal x-direction (radial) and y-direction (axial), and rotation about the nodal z-axis (hoop). In addition, the axisymmetric conical shell element is biaxial, with membrane and bending capabilities. The OCA inner shell defines the outer confinement vessel (OCV).
Relatively stiff, 2-D elastic beams (BEAM3) are utilized to maintain bending continuity between the three degree of freedom conical shell elements and two degree of freedom, isoparametric solid elements. Specifically, for both the lower and upper OCV seal flanges, four stiff beams are placed at each junction between the shell elements and the solid elements of the seal flanges.
These elements are included to transmit the moment (i.e., to maintain slope continuity) between the shell and flange portions of the model, and have a negligible effect on the stress results.
Three sets of 2-D interface elements (CONTAC12) are utilized to connect the lower and upper OCV seal flanges to each other and to the OCV locking ring. The interface element is capable of supporting a load only in the direction normal to the surfaces, and is frictionless in the tangential direction. The interface element has two degrees of freedom at each node: translations in the nodal x-direction (radial) and y-direction (axial). A contact stiffness of 1 x 109 lb/in is chosen to reflect the relatively high interface stiffness when closed. Three sets of interface elements are used in these analyses: 1) between the lower OCV seal flange and the OCV locking ring, 2) between the upper OCV seal flange and the OCV locking ring, and 3) between the lower OCV seal flange and the upper OCV seal flange. Relatively flexible spring elements (COMBIN14) having a spring stiffness of 1 x 102 lb/in are also used at these same locations to improve model stability and to reduce interface element convergence time. The resulting forces in these springs are small, having a negligible effect on the stress results.
1 ANSYS, Inc., ANSYS Engineering Analysis System Users Manual for ANSYS Revision 5.3, Houston, PA.
2.10.1-1
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 Interface elements are also located along the entire shell-to-foam periphery to allow relative motion between the steel shells and the polyurethane foam. This approach effectively models the ceramic fiber paper by allowing compression-only forces, and assumes no shear continuity or tension effects. A contact stiffness of 1 x 105 lb/in is chosen to reflect the interface stiffness between the shells, ceramic fiber paper, and polyurethane foam. Stress results in the package shells and OCV seal flanges exhibit a negligible dependence on the actual magnitude of the gap contact stiffness.
To account for the tangential (hoop) direction slotting for the lower OCV seal flange and OCV locking ring in the axisymmetric model, the material properties in the directly affected regions are modified. Specifically, material properties for the shaded elements in the lower OCV seal flange and OCV locking ring, illustrated on Figure 2.10.1-1, are modified to reflect only one-half the stainless steel being present for strength purposes. Specifically, the elastic modulus in the x-and y-directions is reduced to one-half their normal value (since only approximately one-half the material remains in the slotted regions), and the elastic modulus in the z-direction is set to set to a very low value to eliminate virtually all tangential (hoop) stiffness in the slotted regions. In addition, Poissons ratio is set at the normal value of 0.3 for the x-y plane, but is set to zero in the y-z and x-z planes. In these ways, the analyses accurately depict the stress levels in all regions.
The global origin of the nodal coordinate system is located at the bottom center of the OCA body, as shown in Figure 2.10.1-1. As such, the nodal x-axis corresponds to the radial direction, the nodal y-axis corresponds to the axial direction, and the nodal z-axis corresponds to the tangential (or hoop) direction. The model is constrained from translating in the radial direction and rotating about the hoop axis at the y-z symmetry plane at x equal zero. The model is also constrained from translating in the axial direction at a single node on the OCV locking ring.
2.10.1.1.1 OCA Structural Analysis - Load Case 1 For OCA Load Case 1, the OCA structural analysis uses a 50 psig (64.7 psia) internal pressure, corresponding to the maximum normal operating pressure (MNOP) from Section 3.4.4, Maximum Internal Pressure, coupled with a reduced external pressure of 3.5 psia (equivalently an 11.2 psig internal pressure), per Section 2.6.3, Reduced External Pressure, and 10 CFR &sect;71.51(c)(3) 2. The net internal pressure for this case is 61.2 psig, applied throughout the inner periphery of the model.
Relative to the upper and lower OCV seal flanges, the internal pressure does not extend beyond (below) the top of the upper main O-ring seal groove.
A uniform temperature of 160 &#xba;F, per Section 2.6.1.1, Summary of Pressures and Temperatures, is utilized to determine the temperature-dependent, material property values. The only material properties affected by a temperature of 160 &#xba;F are the elastic modulus and the thermal expansion coefficient for the stainless steel. Consistent with Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the elastic modulus and thermal expansion coefficient for Type 304 stainless steel are 27.8(10)6 psi and 8.694(10)-6 inches/inch/&#xba;F, respectively, at a temperature of 160 &#xba;F.
The material properties for the polyurethane foam are consistent with those specified in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations. The elastic modulus in the x-2 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2.10.1-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 (radial) and z- (hoop) directions is based on the perpendicular-to-rise value of 4,773 psi.
Youngs modulus in the y- (axial) direction is based on the parallel-to-rise value of 6,810 psi. In addition, Poissons ratio is 0.33, and the thermal expansion coefficient is 3.5(10)-5 inches/inch/&#xba;F for the polyurethane foam. Due to the relatively low stiffness of the polyurethane foam compared with the surrounding stainless steel structures, temperature adjusting the foams elastic modulus and thermal expansion coefficient will have a negligible effect on component stresses.
Both the reference and uniform temperature are set to 160 &#xba;F, thereby excluding the effects of differential thermal expansion for this case. The effects of differential thermal expansion are considered in Section 2.10.1.1.2, OCA Structural Analysis - Load Case 2.
For analysis model review, the ANSYS input file is listed in Table 2.10.1-1.
2.10.1.1.2 OCA Structural Analysis - Load Case 2 For OCA Load Case 2, the OCA structural analysis uses a 50 psig (64.7 psia) internal pressure, corresponding to the maximum normal operating pressure (MNOP) from Section 3.4.4, Maximum Internal Pressure, coupled with a reduced external pressure of 3.5 psia (equivalently an 11.2 psig internal pressure), per Section 2.6.3, Reduced External Pressure, and 10 CFR &sect;71.51(c)(3). The net internal pressure for this case is 61.2 psig, applied throughout the inner periphery of the model.
Relative to the upper and lower OCV seal flanges, the internal pressure does not extend beyond (below) the top of the upper main O-ring seal groove.
A uniform temperature of 160 &#xba;F, per Section 2.6.1.1, Summary of Pressures and Temperatures, is utilized to determine the temperature-dependent, material property values. The only material properties affected by a temperature of 160 &#xba;F are the elastic modulus and the thermal expansion coefficient for the stainless steel. Consistent with Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the elastic modulus and thermal expansion coefficient for Type 304 stainless steel are 27.8(10)6 psi and 8.694(10)-6 inches/inch/&#xba;F, respectively, at a temperature of 160 &#xba;F.
The material properties for the polyurethane foam are consistent with those specified in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations. The elastic modulus in the x-(radial) and z- (hoop) directions is based on the perpendicular-to-rise value of 4,773 psi.
Youngs modulus in the y- (axial) direction is based on the parallel-to-rise value of 6,810 psi. In addition, Poissons ratio is 0.33, and the thermal expansion coefficient is 3.5(10)-5 inches/inch/&#xba;F for the polyurethane foam. Due to the relatively low stiffness of the polyurethane foam compared with the surrounding stainless steel structures, temperature adjusting the foams elastic modulus and thermal expansion coefficient will have a negligible effect on component stresses.
The reference temperature is set to 70 &#xba;F, and the uniform temperature is set to 160 &#xba;F, thereby including the effects of differential thermal expansion for this case.
For analysis model review, the ANSYS input file is listed in Table 2.10.1-2.
2.10.1.1.3 OCA Structural Analysis - Load Case 3 For OCA Load Case 3, the OCA structural analysis uses a 0.0 psig (14.7 psia) internal pressure coupled with an external pressure of 0.0 psig (14.7 psia) for a net pressure differential of 0.0 psig.
A uniform temperature of -40 &#xba;F, per Section 2.6.2, Cold, is utilized to determine the temperature-dependent, material property values. The only material properties affected by a temperature of 2.10.1-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
-40 &#xba;F are the elastic modulus and the thermal expansion coefficient for the stainless steel.
Consistent with Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the elastic modulus and thermal expansion coefficient for Type 304 stainless steel are 28.8(10)6 psi and 8.21(10)-6 inches/inch/&#xba;F, respectively, at a temperature of -40 &#xba;F.
The material properties for the polyurethane foam are consistent with those specified in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations. The elastic modulus in the x-(radial) and z- (hoop) directions is based on the perpendicular-to-rise value of 4,773 psi.
Youngs modulus in the y- (axial) direction is based on the parallel-to-rise value of 6,810 psi. In addition, Poissons ratio is 0.33, and the thermal expansion coefficient is 3.5(10)-5 inches/inch/&#xba;F for the polyurethane foam. Due to the relatively low stiffness of the polyurethane foam compared with the surrounding stainless steel structures, temperature adjusting the foams elastic modulus and thermal expansion coefficient will have a negligible effect on component stresses.
The reference temperature is set to 70 &#xba;F, and the uniform temperature is set to -40 &#xba;F, thereby including the effects of differential thermal expansion for this case.
For analysis model review, the ANSYS input file is listed in Table 2.10.1-3.
2.10.1.1.4 OCA Structural Analysis - Load Case 4 For OCA Load Case 4, the OCA structural analysis uses a -14.7 psig (0.0 psia) internal pressure (i.e., full vacuum) coupled with a increased external pressure of 0.0 psig (14.7 psia), per Section 2.6.4, Increased External Pressure. The net external pressure for this case is 14.7 psig, applied throughout the inner periphery of the model. Relative to the upper and lower OCV seal flanges, the internal pressure does not extend beyond (below) the top of the upper main O-ring seal groove.
A uniform temperature of 70 &#xba;F is utilized to determine the temperature-dependent, material property values. The only material properties affected by a temperature of 70 &#xba;F are the elastic modulus and the thermal expansion coefficient for the stainless steel. Consistent with Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the elastic modulus and thermal expansion coefficient for Type 304 stainless steel are 28.3(10)6 psi and 8.46(10)-6 inches/inch/&#xba;F, respectively, at a temperature of 70 &#xba;F.
The material properties for the polyurethane foam are consistent with those specified in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations. The elastic modulus in the x-(radial) and z- (hoop) directions is based on the perpendicular-to-rise value of 4,773 psi.
Youngs modulus in the y- (axial) direction is based on the parallel-to-rise value of 6,810 psi. In addition, Poissons ratio is 0.33, and the thermal expansion coefficient is 3.5(10)-5 inches/inch/&#xba;F for the polyurethane foam. Due to the relatively low stiffness of the polyurethane foam compared with the surrounding stainless steel structures, temperature adjusting the foams elastic modulus and thermal expansion coefficient will have a negligible effect on component stresses.
Both the reference and uniform temperature are set to 70 &#xba;F, thereby excluding the effects of differential thermal expansion for this case.
For analysis model review, the ANSYS input file is listed in Table 2.10.1-4.
2.10.1.2 Inner Containment Vessel (ICV) Structural Analysis Finite element analyses (FEA) are performed on the ICV structure to determine the stress states of the various components under normal conditions of transport (NCT) loads. The FEA analyses 2.10.1-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 are performed using ANSYS 5.3. The ICV FEA model is comprised of four separate major structural components, modeled as shown in Figure 2.10.1-2:
* upper ICV seal flange
* ICV locking ring
* lower ICV seal flange
* ICV shells The lower and upper seal flanges, and locking ring are modeled using 2-D, isoparametric solid elements (PLANE42). The quadrilateral elements are defined by four nodal points (a triangular element may be formed by defining duplicate the 3rd and 4th node numbers), each having two degrees of freedom: translations in the nodal x-direction (radial) and y-direction (axial).
The upper and lower ICV shells (ICV lid and body shells, respectively) are modeled using 2-D, axisymmetric conical shell elements (SHELL51). The lineal elements are defined by two nodal points, each having three degrees of freedom: translations in the nodal x-direction (radial) and y-direction (axial), and rotation about the nodal z-axis (hoop). In addition, the axisymmetric conical shell element is biaxial, with membrane and bending capabilities.
Relatively stiff, 2-D elastic beams (BEAM3) are utilized to maintain bending continuity between the three degree of freedom conical shell elements and two degree of freedom, isoparametric solid elements. Specifically, for both the lower and upper ICV seal flanges, four stiff beams are placed at each junction between the shell elements and the solid elements of the seal flanges.
These elements are included to transmit the moment (i.e., to maintain slope continuity) between the shell and flange portions of the model, and have a negligible effect on the stress results.
Three sets of 2-D interface elements (CONTAC12) are utilized to connect the lower and upper ICV seal flanges to each other and to the ICV locking ring. The interface element is capable of supporting a load only in the direction normal to the surfaces, and is frictionless in the tangential direction. The interface element has two degrees of freedom at each node: translations in the nodal x-direction (radial) and y-direction (axial). A contact stiffness of 1 x 109 lb/in is chosen to reflect the relatively high interface stiffness when closed. Three sets of interface elements are used in these analyses: 1) between the lower ICV seal flange and the ICV locking ring,
: 2) between the upper ICV seal flange and the ICV locking ring, and 3) between the lower ICV seal flange and the upper ICV seal flange.
To account for the tangential (hoop) direction slotting for the lower ICV seal flange and ICV locking ring in the axisymmetric model, the material properties in the directly affected regions are modified. Specifically, material properties for the shaded elements in the lower ICV seal flange and ICV locking ring, illustrated on Figure 2.10.1-2, are modified to reflect only one-half the stainless steel being present for strength purposes. Specifically, the elastic modulus in the x-and y-directions is reduced to one-half their normal value (since only approximately one-half the material remains in the slotted regions), and the elastic modulus in the z-direction is set to set to a very low value to eliminate virtually all tangential (hoop) stiffness in the slotted regions. In addition, Poissons ratio is set at the normal value of 0.3 for the x-y plane, but is set to zero in the y-z and x-z planes. In these ways, the analyses accurately depict the stress levels in all regions.
The global origin of the nodal coordinate system is located at the bottom center of the ICV body, as shown in Figure 2.10.1-2. As such, the nodal x-axis corresponds to the radial direction, the nodal y-axis corresponds to the axial direction, and the nodal z-axis corresponds to the tangential (or hoop) direction. The model is constrained from translating in the radial direction and rotating 2.10.1-5
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 about the hoop axis at the y-z symmetry plane at x equal zero. The model is also constrained from translating in the axial direction at a single node on the ICV locking ring.
2.10.1.2.1 ICV Structural Analysis - Load Case 1 For ICV Load Case 1, the ICV structural analysis uses a 50 psig (64.7 psia) internal pressure, corresponding to the maximum normal operating pressure (MNOP) from Section 3.4.4, Maximum Internal Pressure, coupled with a reduced external pressure of 3.5 psia (equivalently an 11.2 psig internal pressure), per Section 2.6.3, Reduced External Pressure, and 10 CFR &sect;71.51(c)(3). The net internal pressure for this case is 61.2 psig, applied throughout the inner periphery of the model.
Relative to the upper and lower ICV seal flanges, the internal pressure does not extend beyond (below) the top of the upper main O-ring seal groove.
A uniform temperature of 160 &#xba;F, per Section 2.6.1.1, Summary of Pressures and Temperatures, is utilized to determine the temperature-dependent, material property values. The only material properties affected by a temperature of 160 &#xba;F are the elastic modulus and the thermal expansion coefficient for the stainless steel. Consistent with Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the elastic modulus and thermal expansion coefficient for Type 304 stainless steel are 27.8(10)6 psi and 8.694(10)-6 inches/inch/&#xba;F, respectively, at a temperature of 160 &#xba;F.
Both the reference and uniform temperature are set to 160 &#xba;F, thereby excluding the effects of differential thermal expansion for this case.
For analysis model review, the ANSYS input file is listed in Table 2.10.1-5.
2.10.1.2.2 ICV Structural Analysis - Load Case 2 For ICV Load Case 4, the OCA structural analysis uses a -14.7 psig (0.0 psia) internal pressure (i.e., full vacuum) coupled with a increased external pressure of 0.0 psig (14.7 psia), per Section 2.6.4, Increased External Pressure. The net external pressure for this case is 14.7 psig, applied throughout the inner periphery of the model. Relative to the upper and lower ICV seal flanges, the internal pressure does not extend beyond (below) the top of the upper main O-ring seal groove.
A uniform temperature of 70 &#xba;F is utilized to determine the temperature-dependent, material property values. The only material properties affected by a temperature of 70 &#xba;F are the elastic modulus and the thermal expansion coefficient for the stainless steel. Consistent with Table 2.3-1 in Section 2.3.1, Mechanical Properties Applied to Analytic Evaluations, the elastic modulus and thermal expansion coefficient for Type 304 stainless steel are 28.3(10)6 psi and 8.46(10)-6 inches/inch/&#xba;F, respectively, at a temperature of 70 &#xba;F.
Both the reference and uniform temperature are set to 70 &#xba;F, thereby excluding the effects of differential thermal expansion for this case.
For analysis model review, the ANSYS input file is listed in Table 2.10.1-6.
2.10.1-6
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 Table 2.10.1 ANSYS Input Listing for OCA Load Case 1
! initialize ANSYS                                        r,137,-64.3041,1e5,,1 fini                                                      r,138,-51.4561,1e5,,1
/cle                                                      r,139,-38.6081,1e5,,1
/filename,oca_lc1,inp                                    r,140,-25.7602,1e5,,1
/out,,txt                                                r,141,-23.1841,1e5,,1 r,142,-20.6081,1e5,,1
! start preprocessing the model                          r,143,-18.0321,1e5,,1
/prep7                                                    r,144,-15.4561,1e5,,1
/title, OCA Load Case 1: P=64.7/3.5 psia, T=160/160 F    r,145,-12.8801,1e5,,1 r,146,-10.3041,1e5,,1
! element types                                          r,147,-7.72805,1e5,,1 et,1,42,,,1                                              r,148,-5.15203,1e5,,1 et,2,51                                                  r,149,-2.57602,1e5,,1 et,3,42,,,1                                              r,150,,1e5,,1 et,4,12,,,,,,,1                                          r,639,-58.7238,1e5,,1 et,5,12,,,,,,,1                                          r,640,-27.4476,1e5,,1 et,6,3                                                    r,641,-24.7029,1e5,,1 et,7,14,,,2                                              r,642,-21.9581,1e5,,1 r,643,-19.2133,1e5,,1
! reference and uniform temperatures                      r,644,-16.4686,1e5,,1 tref,160                                                  r,645,-13.7238,1e5,,1 tunif,160                                                r,646,-10.9790,1e5,,1 r,647,-8.23429,1e5,,1
! material properties for non-slotted steel regions      r,648,-5.48952,1e5,,1 ex,1,27.8e06                                              r,649,-2.74476,1e5,,1 nuxy,1,.3 alpx,1,8.694e-06                                          ! nodes for the lower seal flange local,11,,38.24941495,50.051977923,,-12
! material properties for slotted steel regions          n,1001 ex,2,13.9e06                                              n,1005,.25 ey,2,13.9e06                                              fill ez,2,1                                                    n,1016,,.58677836 nuxy,2,.3                                                n,1020,.25,.58677836 nuxz,2,0                                                  fill nuyz,2,0                                                  fill,1001,1016,2,1006,5,5,1 alpx,2,8.694e-06                                          n,1026,,.896632635 alpy,2,8.694e-06                                          local,12,,38.505,50 alpz,2,8.694e-06                                          move,1026,11,0,999,0,12,-.065,999,0 fill,1016,1026,1,1021
! material properties for the polyurethane foam          local,11,1,39.12699808,50.47 ex,3,4773                                                n,1025,.5,148.5 ey,3,6810                                                n,1030,.5,129 ez,3,4773                                                n,1031,.5,109.5 nuxy,3,.33                                                n,1032,.5,90 nuxz,3,.33                                                csys,12 nuyz,3,.33                                                fill,1021,1025,3,1022,1,2,5 alpx,3,3.5e-5                                            n,1033,.775,.97 n,1034,1.145,.97
! material properties for the rigid coupling elements    n,1076,-.065,2.98 ex,4,27.8e06                                              fill,1026,1076,8,1035,5 nuxy,4,.3                                                fill,1035,1076,7,1041,5 alpx,4,8.694E-06                                          n,1060,.775,2.15593612 ngen,2,6,1033,1034,1,,.16
! element real constants                                  fill,1039,1060,3,1045,5 r,1,.25                                                  fill,1035,1039 r,2,.1875                                                fill,1041,1045,3,1042,1,4,5 r,3,.375                                                  n,1064,1.245,2.03 r,4,.075                                                  fill,1060,1064 r,5,,1e9,,1                                              n,1092,-.065,2.98 r,6,-15,1e9,-.036                                        n,1096,.77960172,2.76 r,7,15,1e9,-.036                                          fill r,8,0,1e9,,1                                              n,1100,1.245,2.76 r,9,1,1,1                                                fill,1096,1100 r,10,1e2                                                  fill,1056,1092,3,1065,9,9,1 r,101,-180.000,1e5,,1                                    ngen,3,9,1098,1100,1,,.26 r,102,-177.444,1e5,,1                                    n,1146,.14020351,4.4 r,103,-174.888,1e5,,1                                    fill,1092,1146,5,1101,9 r,104,-172.333,1e5,,1                                    n,1164,.14020351,4.98 r,105,-169.777,1e5,,1                                    fill,1146,1164,1,1155 r,106,-167.221,1e5,,1                                    local,11,,39.13520351,54.98,,-86.15 r,107,-164.665,1e5,,1                                    n,1168 r,108,-162.109,1e5,,1                                    n,1159,.3 r,109,-159.553,1e5,,1                                    ngen,3,-1,1159,1159,,,-.125 r,110,-156.998,1e5,,1                                    n,1148,.58,-.25 r,111,-154.442,1e5,,1                                    ngen,2,-18,1157,1159,1,.56 r,112,-141.553,1e5,,1                                    ngen,2,-9,1139,1141,1,.25 r,113,-128.665,1e5,,1                                    ngen,2,-27,1148,1148,,.81 r,114,-115.777,1e5,,1                                    ngen,2,-18,1130,1132,1,.56 r,115,-102.888,1e5,,1                                    fill,1096,1114,1,1105 r,116,-90.0000,1e5,,1                                    csys,12 r,130,-102.000,1e5,,1                                    fill,1101,1105 r,136,-77.1520,1e5,,1                                    fill,1110,1112,1,1111,,6,9 2.10.1-7
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 fill,1164,1168                              ngen,2,-879,1003,1003 fill,122,124
! nodes for the upper seal flange          ngen,2,-1870,2003,2003 local,11,,38.405,52.81                      n,135,38.53,63.78649751 n,2001,,5                                  fill,133,135 n,2005,.25,5                                local,12,1,29.905,63.78649751 fill                                        n,140,8.625,64.23984399 ngen,3,5,2001,2005,1,,-.25                  fill,135,140 n,2031,,3.45                                local,14,1,,1.8125 n,2035,.91,3.45                            n,150,77.4375,90 fill                                        fill,140,150 fill,2011,2031,3,2016,5,5,1 n,2051,,2.543442101                        ! nodes for the OCA outer shell n,2055,.91,2.543442101                      csys fill                                        n,601 fill,2031,2051,3,2036,5,4,1                n,613,47.0625 n,2040,.91,3.29                            fill fill,2040,2055,2,2045,5                    n,622,47.0625,46.7775 n,2059,1.345,2.66                          fill,613,622 fill,2055,2059                              n,630,47.0625,47.6325 n,2071,,2.17                                n,638,47.0625,75.3440689 n,2073,.21504507,2.17                      fill,630,638 fill                                        local,15,1,40.5625,75.3440689 n,2077,.74504507,2.17                      n,640,6.5,62.55238078 fill,2073,2077                              fill,638,640 fill,2051,2071,1,2060                      local,16,1,,-2.75 fill,2054,2076,1,2065                      n,650,94.5,90 fill,2060,2065                              fill,640,650 n,2081,1.345,2.17 fill,2077,2081                              ! nodes for the polyurethane foam inner surface fill,2055,2077,1,2066,,5,1                  csys n,2107,.85759646,.54                        ngen,2,100,101,150,1 n,2109,1.10488343,.54                      n,125,38.58338729,50.9 fill                                        n,232,38.53,56.26 n,2111,1.345,.54 fill,2109,2111                              ! nodes for the polyurethane foam outer surface fill,2077,2107,5,2082,5,5,1                ngen,2,-100,601,650,1 n,2117,.94488343 n,2119,1.10488343                          ! intermediate polyurethane foam nodes fill                                        fill,201,501,2,301,100,22,1 fill,2109,2119,1,2114                      n,300,43.9375,50.9 n,2112,.870715847,.35                      n,331,41.5375,51.8825 fill,2112,2114                              n,332,41.5375,56.26 n,2120,1.345,3.45                          n,422,43.9375,46.7775 n,2121,1.345,3.29                          n,430,44.2375,47.6375 ngen,2,51,2071,2073,1,,-.305                n,431,44.2375,51.8825 ngen,2,3,2122,2124,1,,-.305                fill,222,422,1,322 fill,223,300,1,323
! nodes for the locking ring                fill,332,532,1,432 local,11,,39.35,51.29                      fill,233,533,2,333,100,18,1 n,3001 n,3005,.435                                ! nodes for the z-flanges fill                                        ngen,2,279,422,422,0 n,3009,.935                                ngen,2,402,300,300,0 fill,3005,3009                              ngen,2,273,430,430,0 n,3037,,.81                                rp2,,,1,1 n,3041,.435,.693442101                      ngen,2,374,331,331,0 fill                                        rp2,,,1,1 n,3045,.935,.693442101 fill,3041,3045                              ! elements for the lower seal flange fill,3001,3037,3,3010,9,9,1                type,1 n,3145,,4.11                                mat,1 n,3149,.435,4.226557899                    real,1 fill                                        e,1001,1002,1007,1006 n,3153,.935,4.226557899                    rp4,1,1,1,1 fill,3149,3153                              egen,5,5,1,4,1 fill,3041,3149,11,3050,9,5,1                e,1026,1027,1036,1035 n,3181,,4.67                                e,1027,1028,1036 n,3185,.535,4.67                            e,1028,1029,1037,1036 fill                                        e,1029,1030,1031,1037 n,3189,.935,4.67                            e,1031,1032,1038,1037 fill,3185,3189                              rp3,1,1,1,1 fill,3145,3181,3,3154,9,9,1                e,1035,1036,1042,1041 rp4,1,1,1,1
! nodes for the OCA inner shell (OCV)      e,1041,1042,1047,1046 local,11,1,,84.5                            rp4,1,1,1,1 n,101,74.25,-90                            egen,3,5,32,35,1 n,111,74.25,-64.44174492                    e,1056,1057,1066,1065 fill                                        rp4,1,1,1,1 local,12,1,28.3125,24.29659664              egen,4,9,44,47,1 n,116,8.625                                mat,2 fill,111,116                                e,1060,1061,1070,1069 csys                                        rp4,1,1,1,1
!n,117,36.9375,25.79659664                  egen,4,9,60,63,1 n,122,36.9375,43.95292590                  egen,3,9,74,75,1 fill,116,122                                egen,3,9,56,59,1 2.10.1-8
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 egen,7,9,84,85,1                              type,3 egen,3,1,99,99                                mat,3 egen,3,1,93,93                                real,1 e,201,301,302,202
! elements for the upper seal flange          rp22,1,1,1,1 type,1                                        e,224,223,323 mat,1                                          e,301,401,402,302 real,1                                        rp21,1,1,1,1 e,2006,2007,2002,2001                          e,322,422,300,323 rp4,1,1,1,1                                    e,300,125,224,323 egen,10,5,104,107,1                            e,401,501,502,402 e,2040,2121,2120,2035                          rp21,1,1,1,1 e,2060,2061,2052,2051                          e,333,233,232,332 e,2061,2062,2052                              e,233,333,334,234 e,2062,2063,2053,2052                          rp17,1,1,1,1 e,2063,2064,2053                              e,331,431,432,332 e,2064,2065,2054,2053                          rp19,1,1,1,1 rp6,1,1,1,1                                    e,430,530,531,431 e,2071,2072,2061,2060                          rp20,1,1,1,1 rp10,1,1,1,1 e,2122,2123,2072,2071                          ! interface elements between the steel shells rp2,1,1,1,1                                    !  and the polyurethane foam e,2125,2126,2123,2122                          type,5 rp2,1,1,1,1                                    mat,1 e,2082,2083,2078,2077                          real,101 rp4,1,1,1,1                                    e,101,201 egen,6,5,169,172,1                            real,102 egen,3,5,189,190,1                            e,102,202 real,103
! elements for the locking ring                e,103,203 type,1                                        real,104 mat,2                                          e,104,204 real,1                                        real,105 e,3001,3002,3011,3010                          e,105,205 rp4,1,1,1,1                                    real,106 egen,4,9,197,200,1                            e,106,206 mat,1                                          real,107 e,3005,3006,3015,3014                          e,107,207 rp4,1,1,1,1                                    real,108 egen,20,9,213,216,1                            e,108,208 e,3145,3146,3155,3154                          real,109 rp4,1,1,1,1                                    e,109,209 egen,4,9,293,296,1                            real,110 e,110,210
! elements for the OCA inner shell (OCV)      real,111 type,2                                        e,111,211 mat,1                                          real,112 real,1                                        e,112,212 e,101,102                                      real,113 rp16,1,1                                      e,113,213 real,2                                        real,114 e,117,118                                      e,114,214 rp5,1,1                                        real,115 real,1                                        e,115,215 e,122,123                                      real,116 e,123,1003                                    e,116,216 e,2003,134                                    rp5,1,1 e,134,135                                      real,130 rp16,1,1                                      e,122,222 rp2,1,1
! elements for the OCA outer shell            e,1003,224 real,1                                        real,101 e,601,602                                      e,702,300 rp18,1,1                                      e,701,422 real,3                                        e,622,522 e,619,620                                      real,150 rp3,1,1                                        e,706,332 e,630,631                                      e,705,331 rp8,1,1                                        e,704,431 real,1                                        e,703,430 e,638,639                                      e,630,530 rp12,1,1                                      real,116 e,300,702
! elements for the Z-flanges                  e,422,701 real,4                                        e,706,332 e,622,701                                      e,705,331 e,701,702                                      e,704,431 e,702,1034                                    e,703,430 e,1034,1033                                    e,2003,233 e,630,703                                      e,134,234 e,703,704                                      rp2,1,1 rp3,1,1                                        real,136 e,706,2120                                    e,136,236 e,2120,2035                                    real,137 e,137,237
! polyurethane foam elements                  real,138 2.10.1-9
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 e,138,238                                                e,1001,1002 real,139                                                  rp4,1,1 e,139,239 real,140                                                  ! couple the upper shell to the upper seal flange e,140,240                                                type,6 real,141                                                  mat,4 e,141,241                                                real,9 real,142                                                  e,2001,2002 e,142,242                                                rp4,1,1 real,143 e,143,243                                                ! springs between the lower seal flange real,144                                                  !  and the locking ring e,144,244                                                type,7 real,145                                                  mat,1 e,145,245                                                real,10 real,146                                                  e,3038,1061 e,146,246                                                rp3,1,1 real,147 e,147,247                                                ! springs between the upper seal flange real,148                                                  !  and the locking ring e,148,248                                                type,7 real,149                                                  mat,1 e,149,249                                                real,10 real,150                                                  e,2056,3146 e,150,250                                                rp3,1,1 real,101 e,501,601                                                ! springs between the lower seal flange rp13,1,1                                                  !  and the upper seal flange real,116                                                  type,7 e,513,613                                                mat,1 rp10,1,1                                                  real,10 e,530,630                                                e,1164,2073 rp9,1,1                                                  rp5,1,1 real,639 e,539,639                                                ! displacement constraints real,640                                                  d,101,UX,0,,601,500,rotz e,540,640                                                d,201,UX,0,,501,100 real,641                                                  d,150,UX,0,,650,500,rotz e,541,641                                                d,250,UX,0,,550,100 real,642                                                  d,3099,UY,0 e,542,642                                                d,all,uz,0 real,643 e,543,643                                                ! pressure loads real,644                                                  alls e,544,644                                                pload=+(64.7-3.5) real,645                                                  p,101,102,pload,,122,1 e,545,645                                                p,123,1003,pload real,646                                                  p,1001,1006,pload,,1021,5 e,546,646                                                p,1026,1035,pload real,647                                                  p,1035,1041,pload e,547,647                                                p,1041,1046,pload,,1051,5 real,648                                                  p,1056,1065,pload,,1155,9 e,548,648                                                p,1164,1165,pload,,1167,1 real,649                                                  p,1168,1159,pload e,549,649                                                p,2077,2082,pload real,150                                                  p,2073,2074,pload,,2076,1 e,550,650                                                p,2127,2124,pload p,2124,2073,pload
! interface elements between the lower seal flange        p,2125,2126,pload,,2126,1
!  and the locking ring                                  p,2122,2125,pload type,4                                                    p,2071,2122,pload mat,1                                                    p,2001,2006,pload,,2046,5 real,6                                                    p,2051,2060,pload e,3038,1061                                              p,2060,2071,pload rp3,1,1                                                  p,2003,134,pload p,134,135,pload,,149,1
! interface elements between the upper seal flange
!  and the locking ring                                  ! delete unused nodes at seal flange interfaces type,4                                                    ndele,124 mat,1                                                    ndele,133 real,7 e,2056,3146                                              ! solve the problem rp3,1,1                                                  fini
                                                          /solu
! interface elements between the lower seal flange        neqit,1000
!  and the upper seal flange                            alls type,5                                                    solv mat,1                                                    fini real,8                                                    save e,1164,2073 rp5,1,1                                                  ! post-process the problem
                                                          /post1
! couple the lower shell to the lower seal flange        set type,6                                                    rsys,solu mat,4                                                    ernorm,0 real,9 2.10.1-10
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
! table stress definitions for shell elements        /com, nall                                                /com,+++++++++++++++++++++++++++++++++++++++
alls                                                /com,+ OCV torispherical head crown shells +
esel,s,type,,2                                      /com,+++++++++++++++++++++++++++++++++++++++
etab,sit,nmisc,4                                    /com, etab,sim,nmisc,9                                    /com, etab,sib,nmisc,14                                    nall eall
/com,                                                esel,s,elem,,339,348,1    ! upper head
/com,                                                esel,a,elem,,309,318,1    ! lower head
/com,                                                pret
/com,+++++++++++++++++++++
/com,+ lower seal flange +                          /com,
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,
/com,                                                /com,+++++++++++++++++++++++++++++++++++++++++
nall                                                /com,+ OCV torispherical head knuckle shells +
eall                                                /com,+++++++++++++++++++++++++++++++++++++++++
nsel,s,node,,1000,1999,1                            /com, prns,prin                                            /com, nall
/com,                                                eall
/com,                                                esel,s,elem,,334,338,1    ! upper head
/com,                                                esel,a,elem,,319,323,1    ! lower head
/com,+++++++++++++++++++++                          pret
/com,+ upper seal flange +
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,
/com,                                                /com, nall                                                /com,++++++++++++++++++++++++++++++++++
eall                                                /com,+ OCA outer shells and z-flanges +
nsel,s,node,,2000,2999,1                            /com,++++++++++++++++++++++++++++++++++
prns,prin                                            /com,
                                                    /com,
/com,                                                nall
/com,                                                eall
/com,                                                esel,s,elem,,349,399,1
/com,++++++++++++++++                                pret
/com,+ locking ring +
/com,++++++++++++++++                                /com,
/com,                                                /com,
/com,                                                /com, nall                                                /com,++++++++++++++++++++++++++++++
eall                                                /com,+ polyurethane foam elements +
nsel,s,node,,3000,3999,1                            /com,++++++++++++++++++++++++++++++
prns,prin                                            /com,
                                                    /com,
/com,                                                nall
/com,                                                eall
/com,                                                esel,s,elem,,415,559,1
/com,++++++++++++++++++++++++++++++++++++++          prns,prin
/com,+ OCV cylindrical and conical shells +
/com,++++++++++++++++++++++++++++++++++++++          ! finalize ANSYS
/com,                                                nall
/com,                                                eall nall                                                save eall                                                /out,term esel,s,elem,,324,331,1                              /eof pret
/com,
/com, 2.10.1-11
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 Table 2.10.1 ANSYS Input Listing for OCA Load Case 2
! initialize ANSYS                                        r,137,-64.3041,1e5,,1 fini                                                      r,138,-51.4561,1e5,,1
/cle                                                      r,139,-38.6081,1e5,,1
/filename,oca_lc2,inp                                      r,140,-25.7602,1e5,,1
/out,,txt                                                  r,141,-23.1841,1e5,,1 r,142,-20.6081,1e5,,1
! start preprocessing the model                            r,143,-18.0321,1e5,,1
/prep7                                                    r,144,-15.4561,1e5,,1
/title, OCA Load Case 2: P=64.7/3.5 psia, T=160/70 F      r,145,-12.8801,1e5,,1 r,146,-10.3041,1e5,,1
! element types                                            r,147,-7.72805,1e5,,1 et,1,42,,,1                                                r,148,-5.15203,1e5,,1 et,2,51                                                    r,149,-2.57602,1e5,,1 et,3,42,,,1                                                r,150,,1e5,,1 et,4,12,,,,,,,1                                            r,639,-58.7238,1e5,,1 et,5,12,,,,,,,1                                            r,640,-27.4476,1e5,,1 et,6,3                                                    r,641,-24.7029,1e5,,1 et,7,14,,,2                                                r,642,-21.9581,1e5,,1 r,643,-19.2133,1e5,,1
! reference and uniform temperatures                      r,644,-16.4686,1e5,,1 tref,70                                                    r,645,-13.7238,1e5,,1 tunif,160                                                  r,646,-10.9790,1e5,,1 r,647,-8.23429,1e5,,1
! material properties for non-slotted steel regions        r,648,-5.48952,1e5,,1 ex,1,27.8e06                                              r,649,-2.74476,1e5,,1 nuxy,1,.3 alpx,1,8.694e-06                                          ! nodes for the lower seal flange local,11,,38.24941495,50.051977923,,-12
! material properties for slotted steel regions            n,1001 ex,2,13.9e06                                              n,1005,.25 ey,2,13.9e06                                              fill ez,2,1                                                    n,1016,,.58677836 nuxy,2,.3                                                  n,1020,.25,.58677836 nuxz,2,0                                                  fill nuyz,2,0                                                  fill,1001,1016,2,1006,5,5,1 alpx,2,8.694e-06                                          n,1026,,.896632635 alpy,2,8.694e-06                                          local,12,,38.505,50 alpz,2,8.694e-06                                          move,1026,11,0,999,0,12,-.065,999,0 fill,1016,1026,1,1021
! material properties for the polyurethane foam            local,11,1,39.12699808,50.47 ex,3,4773                                                  n,1025,.5,148.5 ey,3,6810                                                  n,1030,.5,129 ez,3,4773                                                  n,1031,.5,109.5 nuxy,3,.33                                                n,1032,.5,90 nuxz,3,.33                                                csys,12 nuyz,3,.33                                                fill,1021,1025,3,1022,1,2,5 alpx,3,3.5e-5                                              n,1033,.775,.97 n,1034,1.145,.97
! material properties for the rigid coupling elements      n,1076,-.065,2.98 ex,4,27.8e06                                              fill,1026,1076,8,1035,5 nuxy,4,.3                                                  fill,1035,1076,7,1041,5 alpx,4,8.694E-06                                          n,1060,.775,2.15593612 ngen,2,6,1033,1034,1,,.16
! element real constants                                  fill,1039,1060,3,1045,5 r,1,.25                                                    fill,1035,1039 r,2,.1875                                                  fill,1041,1045,3,1042,1,4,5 r,3,.375                                                  n,1064,1.245,2.03 r,4,.075                                                  fill,1060,1064 r,5,,1e9,,1                                                n,1092,-.065,2.98 r,6,-15,1e9,-.036                                          n,1096,.77960172,2.76 r,7,15,1e9,-.036                                          fill r,8,0,1e9,,1                                              n,1100,1.245,2.76 r,9,1,1,1                                                  fill,1096,1100 r,10,1e2                                                  fill,1056,1092,3,1065,9,9,1 r,101,-180.000,1e5,,1                                      ngen,3,9,1098,1100,1,,.26 r,102,-177.444,1e5,,1                                      n,1146,.14020351,4.4 r,103,-174.888,1e5,,1                                      fill,1092,1146,5,1101,9 r,104,-172.333,1e5,,1                                      n,1164,.14020351,4.98 r,105,-169.777,1e5,,1                                      fill,1146,1164,1,1155 r,106,-167.221,1e5,,1                                      local,11,,39.13520351,54.98,,-86.15 r,107,-164.665,1e5,,1                                      n,1168 r,108,-162.109,1e5,,1                                      n,1159,.3 r,109,-159.553,1e5,,1                                      ngen,3,-1,1159,1159,,,-.125 r,110,-156.998,1e5,,1                                      n,1148,.58,-.25 r,111,-154.442,1e5,,1                                      ngen,2,-18,1157,1159,1,.56 r,112,-141.553,1e5,,1                                      ngen,2,-9,1139,1141,1,.25 r,113,-128.665,1e5,,1                                      ngen,2,-27,1148,1148,,.81 r,114,-115.777,1e5,,1                                      ngen,2,-18,1130,1132,1,.56 r,115,-102.888,1e5,,1                                      fill,1096,1114,1,1105 r,116,-90.0000,1e5,,1                                      csys,12 r,130,-102.000,1e5,,1                                      fill,1101,1105 r,136,-77.1520,1e5,,1                                      fill,1110,1112,1,1111,,6,9 2.10.1-12
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 fill,1164,1168                              ngen,2,-879,1003,1003 fill,122,124
! nodes for the upper seal flange            ngen,2,-1870,2003,2003 local,11,,38.405,52.81                      n,135,38.53,63.78649751 n,2001,,5                                    fill,133,135 n,2005,.25,5                                local,12,1,29.905,63.78649751 fill                                        n,140,8.625,64.23984399 ngen,3,5,2001,2005,1,,-.25                  fill,135,140 n,2031,,3.45                                local,14,1,,1.8125 n,2035,.91,3.45                              n,150,77.4375,90 fill                                        fill,140,150 fill,2011,2031,3,2016,5,5,1 n,2051,,2.543442101                          ! nodes for the OCA outer shell n,2055,.91,2.543442101                      csys fill                                        n,601 fill,2031,2051,3,2036,5,4,1                  n,613,47.0625 n,2040,.91,3.29                              fill fill,2040,2055,2,2045,5                      n,622,47.0625,46.7775 n,2059,1.345,2.66                            fill,613,622 fill,2055,2059                              n,630,47.0625,47.6325 n,2071,,2.17                                n,638,47.0625,75.3440689 n,2073,.21504507,2.17                        fill,630,638 fill                                        local,15,1,40.5625,75.3440689 n,2077,.74504507,2.17                        n,640,6.5,62.55238078 fill,2073,2077                              fill,638,640 fill,2051,2071,1,2060                        local,16,1,,-2.75 fill,2054,2076,1,2065                        n,650,94.5,90 fill,2060,2065                              fill,640,650 n,2081,1.345,2.17 fill,2077,2081                              ! nodes for the polyurethane foam inner surface fill,2055,2077,1,2066,,5,1                  csys n,2107,.85759646,.54                        ngen,2,100,101,150,1 n,2109,1.10488343,.54                        n,125,38.58338729,50.9 fill                                        n,232,38.53,56.26 n,2111,1.345,.54 fill,2109,2111                              ! nodes for the polyurethane foam outer surface fill,2077,2107,5,2082,5,5,1                  ngen,2,-100,601,650,1 n,2117,.94488343 n,2119,1.10488343                            ! intermediate polyurethane foam nodes fill                                        fill,201,501,2,301,100,22,1 fill,2109,2119,1,2114                        n,300,43.9375,50.9 n,2112,.870715847,.35                        n,331,41.5375,51.8825 fill,2112,2114                              n,332,41.5375,56.26 n,2120,1.345,3.45                            n,422,43.9375,46.7775 n,2121,1.345,3.29                            n,430,44.2375,47.6375 ngen,2,51,2071,2073,1,,-.305                n,431,44.2375,51.8825 ngen,2,3,2122,2124,1,,-.305                  fill,222,422,1,322 fill,223,300,1,323
! nodes for the locking ring                fill,332,532,1,432 local,11,,39.35,51.29                        fill,233,533,2,333,100,18,1 n,3001 n,3005,.435                                  ! nodes for the z-flanges fill                                        ngen,2,279,422,422,0 n,3009,.935                                  ngen,2,402,300,300,0 fill,3005,3009                              ngen,2,273,430,430,0 n,3037,,.81                                  rp2,,,1,1 n,3041,.435,.693442101                      ngen,2,374,331,331,0 fill                                        rp2,,,1,1 n,3045,.935,.693442101 fill,3041,3045                              ! elements for the lower seal flange fill,3001,3037,3,3010,9,9,1                  type,1 n,3145,,4.11                                mat,1 n,3149,.435,4.226557899                      real,1 fill                                        e,1001,1002,1007,1006 n,3153,.935,4.226557899                      rp4,1,1,1,1 fill,3149,3153                              egen,5,5,1,4,1 fill,3041,3149,11,3050,9,5,1                e,1026,1027,1036,1035 n,3181,,4.67                                e,1027,1028,1036 n,3185,.535,4.67                            e,1028,1029,1037,1036 fill                                        e,1029,1030,1031,1037 n,3189,.935,4.67                            e,1031,1032,1038,1037 fill,3185,3189                              rp3,1,1,1,1 fill,3145,3181,3,3154,9,9,1                  e,1035,1036,1042,1041 rp4,1,1,1,1
! nodes for the OCA inner shell (OCV)        e,1041,1042,1047,1046 local,11,1,,84.5                            rp4,1,1,1,1 n,101,74.25,-90                              egen,3,5,32,35,1 n,111,74.25,-64.44174492                    e,1056,1057,1066,1065 fill                                        rp4,1,1,1,1 local,12,1,28.3125,24.29659664              egen,4,9,44,47,1 n,116,8.625                                  mat,2 fill,111,116                                e,1060,1061,1070,1069 csys                                        rp4,1,1,1,1
!n,117,36.9375,25.79659664                  egen,4,9,60,63,1 n,122,36.9375,43.95292590                    egen,3,9,74,75,1 fill,116,122                                egen,3,9,56,59,1 2.10.1-13
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 egen,7,9,84,85,1                                type,3 egen,3,1,99,99                                  mat,3 egen,3,1,93,93                                  real,1 e,201,301,302,202
! elements for the upper seal flange            rp22,1,1,1,1 type,1                                          e,224,223,323 mat,1                                          e,301,401,402,302 real,1                                          rp21,1,1,1,1 e,2006,2007,2002,2001                          e,322,422,300,323 rp4,1,1,1,1                                    e,300,125,224,323 egen,10,5,104,107,1                            e,401,501,502,402 e,2040,2121,2120,2035                          rp21,1,1,1,1 e,2060,2061,2052,2051                          e,333,233,232,332 e,2061,2062,2052                                e,233,333,334,234 e,2062,2063,2053,2052                          rp17,1,1,1,1 e,2063,2064,2053                                e,331,431,432,332 e,2064,2065,2054,2053                          rp19,1,1,1,1 rp6,1,1,1,1                                    e,430,530,531,431 e,2071,2072,2061,2060                          rp20,1,1,1,1 rp10,1,1,1,1 e,2122,2123,2072,2071                          ! interface elements between the steel shells rp2,1,1,1,1                                    !  and the polyurethane foam e,2125,2126,2123,2122                          type,5 rp2,1,1,1,1                                    mat,1 e,2082,2083,2078,2077                          real,101 rp4,1,1,1,1                                    e,101,201 egen,6,5,169,172,1                              real,102 egen,3,5,189,190,1                              e,102,202 real,103
! elements for the locking ring                e,103,203 type,1                                          real,104 mat,2                                          e,104,204 real,1                                          real,105 e,3001,3002,3011,3010                          e,105,205 rp4,1,1,1,1                                    real,106 egen,4,9,197,200,1                              e,106,206 mat,1                                          real,107 e,3005,3006,3015,3014                          e,107,207 rp4,1,1,1,1                                    real,108 egen,20,9,213,216,1                            e,108,208 e,3145,3146,3155,3154                          real,109 rp4,1,1,1,1                                    e,109,209 egen,4,9,293,296,1                              real,110 e,110,210
! elements for the OCA inner shell (OCV)        real,111 type,2                                          e,111,211 mat,1                                          real,112 real,1                                          e,112,212 e,101,102                                      real,113 rp16,1,1                                        e,113,213 real,2                                          real,114 e,117,118                                      e,114,214 rp5,1,1                                        real,115 real,1                                          e,115,215 e,122,123                                      real,116 e,123,1003                                      e,116,216 e,2003,134                                      rp5,1,1 e,134,135                                      real,130 rp16,1,1                                        e,122,222 rp2,1,1
! elements for the OCA outer shell              e,1003,224 real,1                                          real,101 e,601,602                                      e,702,300 rp18,1,1                                        e,701,422 real,3                                          e,622,522 e,619,620                                      real,150 rp3,1,1                                        e,706,332 e,630,631                                      e,705,331 rp8,1,1                                        e,704,431 real,1                                          e,703,430 e,638,639                                      e,630,530 rp12,1,1                                        real,116 e,300,702
! elements for the Z-flanges                    e,422,701 real,4                                          e,706,332 e,622,701                                      e,705,331 e,701,702                                      e,704,431 e,702,1034                                      e,703,430 e,1034,1033                                    e,2003,233 e,630,703                                      e,134,234 e,703,704                                      rp2,1,1 rp3,1,1                                        real,136 e,706,2120                                      e,136,236 e,2120,2035                                    real,137 e,137,237
! polyurethane foam elements                    real,138 2.10.1-14
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 e,138,238                                                e,1001,1002 real,139                                                  rp4,1,1 e,139,239 real,140                                                  ! couple the upper shell to the upper seal flange e,140,240                                                type,6 real,141                                                  mat,4 e,141,241                                                real,9 real,142                                                  e,2001,2002 e,142,242                                                rp4,1,1 real,143 e,143,243                                                ! springs between the lower seal flange real,144                                                  !  and the locking ring e,144,244                                                type,7 real,145                                                  mat,1 e,145,245                                                real,10 real,146                                                  e,3038,1061 e,146,246                                                rp3,1,1 real,147 e,147,247                                                ! springs between the upper seal flange real,148                                                  !  and the locking ring e,148,248                                                type,7 real,149                                                  mat,1 e,149,249                                                real,10 real,150                                                  e,2056,3146 e,150,250                                                rp3,1,1 real,101 e,501,601                                                ! springs between the lower seal flange rp13,1,1                                                  !  and the upper seal flange real,116                                                  type,7 e,513,613                                                mat,1 rp10,1,1                                                  real,10 e,530,630                                                e,1164,2073 rp9,1,1                                                  rp5,1,1 real,639 e,539,639                                                ! displacement constraints real,640                                                  d,101,UX,0,,601,500,rotz e,540,640                                                d,201,UX,0,,501,100 real,641                                                  d,150,UX,0,,650,500,rotz e,541,641                                                d,250,UX,0,,550,100 real,642                                                  d,3099,UY,0 e,542,642                                                d,all,uz,0 real,643 e,543,643                                                ! pressure loads real,644                                                  alls e,544,644                                                pload=+(64.7-3.5) real,645                                                  p,101,102,pload,,122,1 e,545,645                                                p,123,1003,pload real,646                                                  p,1001,1006,pload,,1021,5 e,546,646                                                p,1026,1035,pload real,647                                                  p,1035,1041,pload e,547,647                                                p,1041,1046,pload,,1051,5 real,648                                                  p,1056,1065,pload,,1155,9 e,548,648                                                p,1164,1165,pload,,1167,1 real,649                                                  p,1168,1159,pload e,549,649                                                p,2077,2082,pload real,150                                                  p,2073,2074,pload,,2076,1 e,550,650                                                p,2127,2124,pload p,2124,2073,pload
! interface elements between the lower seal flange        p,2125,2126,pload,,2126,1
!  and the locking ring                                  p,2122,2125,pload type,4                                                    p,2071,2122,pload mat,1                                                    p,2001,2006,pload,,2046,5 real,6                                                    p,2051,2060,pload e,3038,1061                                              p,2060,2071,pload rp3,1,1                                                  p,2003,134,pload p,134,135,pload,,149,1
! interface elements between the upper seal flange
!  and the locking ring                                  ! delete unused nodes at seal flange interfaces type,4                                                    ndele,124 mat,1                                                    ndele,133 real,7 e,2056,3146                                              ! solve the problem rp3,1,1                                                  fini
                                                          /solu
! interface elements between the lower seal flange        neqit,1000
!  and the upper seal flange                            alls type,5                                                    solv mat,1                                                    fini real,8                                                    save e,1164,2073 rp5,1,1                                                  ! post-process the problem
                                                          /post1
! couple the lower shell to the lower seal flange        set type,6                                                    rsys,solu mat,4                                                    ernorm,0 real,9 2.10.1-15
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
! table stress definitions for shell elements        /com,+++++++++++++++++++++++++++++++++++++++
nall                                                /com,+ OCV torispherical head crown shells +
alls                                                /com,+++++++++++++++++++++++++++++++++++++++
esel,s,type,,2                                      /com, etab,sit,nmisc,4                                    /com, etab,sim,nmisc,9                                    nall etab,sib,nmisc,14                                    eall esel,s,elem,,339,348,1    ! upper head
/com,                                                esel,a,elem,,309,318,1    ! lower head
/com,                                                pret
/com,
/com,+++++++++++++++++++++                          /com,
/com,+ lower seal flange +                          /com,
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,+++++++++++++++++++++++++++++++++++++++++
/com,                                                /com,+ OCV torispherical head knuckle shells +
nall                                                /com,+++++++++++++++++++++++++++++++++++++++++
eall                                                /com, nsel,s,node,,1000,1999,1                            /com, prns,prin                                            nall eall
/com,                                                esel,s,elem,,334,338,1    ! upper head
/com,                                                esel,a,elem,,319,323,1    ! lower head
/com,                                                pret
/com,+++++++++++++++++++++
/com,+ upper seal flange +                          /com,
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,
/com,                                                /com,++++++++++++++++++++++++++++++++++
nall                                                /com,+ OCA outer shells and z-flanges +
eall                                                /com,++++++++++++++++++++++++++++++++++
nsel,s,node,,2000,2999,1                            /com, prns,prin                                            /com, nall
/com,                                                eall
/com,                                                esel,s,elem,,349,399,1
/com,                                                pret
/com,++++++++++++++++
/com,+ locking ring +                                /com,
/com,++++++++++++++++                                /com,
/com,                                                /com,
/com,                                                /com,++++++++++++++++++++++++++++++
nall                                                /com,+ polyurethane foam elements +
eall                                                /com,++++++++++++++++++++++++++++++
nsel,s,node,,3000,3999,1                            /com, prns,prin                                            /com, nall
/com,                                                eall
/com,                                                esel,s,elem,,415,559,1
/com,                                                prns,prin
/com,++++++++++++++++++++++++++++++++++++++
/com,+ OCV cylindrical and conical shells +          ! finalize ANSYS
/com,++++++++++++++++++++++++++++++++++++++          nall
/com,                                                eall
/com,                                                save nall                                                /out,term eall                                                /eof esel,s,elem,,324,331,1 pret
/com,
/com,
/com, 2.10.1-16
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 Table 2.10.1 ANSYS Input Listing for OCA Load Case 3
! initialize ANSYS                                        r,137,-64.3041,1e5,,1 fini                                                      r,138,-51.4561,1e5,,1
/cle                                                      r,139,-38.6081,1e5,,1
/filename,oca_lc3,inp                                      r,140,-25.7602,1e5,,1
/out,,txt                                                  r,141,-23.1841,1e5,,1 r,142,-20.6081,1e5,,1
! start preprocessing the model                            r,143,-18.0321,1e5,,1
/prep7                                                    r,144,-15.4561,1e5,,1
/title, OCA Load Case 3: P=14.7/14.7 psia, T=-40/70 F      r,145,-12.8801,1e5,,1 r,146,-10.3041,1e5,,1
! element types                                            r,147,-7.72805,1e5,,1 et,1,42,,,1                                                r,148,-5.15203,1e5,,1 et,2,51                                                    r,149,-2.57602,1e5,,1 et,3,42,,,1                                                r,150,,1e5,,1 et,4,12,,,,,,,1                                            r,639,-58.7238,1e5,,1 et,5,12,,,,,,,1                                            r,640,-27.4476,1e5,,1 et,6,3                                                    r,641,-24.7029,1e5,,1 et,7,14,,,2                                                r,642,-21.9581,1e5,,1 r,643,-19.2133,1e5,,1
! reference and uniform temperatures                      r,644,-16.4686,1e5,,1 tref,70                                                    r,645,-13.7238,1e5,,1 tunif,-40                                                  r,646,-10.9790,1e5,,1 r,647,-8.23429,1e5,,1
! material properties for non-slotted steel regions        r,648,-5.48952,1e5,,1 ex,1,28.8e06                                              r,649,-2.74476,1e5,,1 nuxy,1,.3 alpx,1,8.21e-06                                            ! nodes for the lower seal flange local,11,,38.24941495,50.051977923,,-12
! material properties for slotted steel regions            n,1001 ex,2,14.4e06                                              n,1005,.25 ey,2,14.4e06                                              fill ez,2,1                                                    n,1016,,.58677836 nuxy,2,.3                                                  n,1020,.25,.58677836 nuxz,2,0                                                  fill nuyz,2,0                                                  fill,1001,1016,2,1006,5,5,1 alpx,2,8.21e-06                                            n,1026,,.896632635 alpy,2,8.21e-06                                            local,12,,38.505,50 alpz,2,8.21e-06                                            move,1026,11,0,999,0,12,-.065,999,0 fill,1016,1026,1,1021
! material properties for the polyurethane foam            local,11,1,39.12699808,50.47 ex,3,4773                                                  n,1025,.5,148.5 ey,3,6810                                                  n,1030,.5,129 ez,3,4773                                                  n,1031,.5,109.5 nuxy,3,.33                                                n,1032,.5,90 nuxz,3,.33                                                csys,12 nuyz,3,.33                                                fill,1021,1025,3,1022,1,2,5 alpx,3,3.5e-5                                              n,1033,.775,.97 n,1034,1.145,.97
! material properties for the rigid coupling elements      n,1076,-.065,2.98 ex,4,28.8e06                                              fill,1026,1076,8,1035,5 nuxy,4,.3                                                  fill,1035,1076,7,1041,5 alpx,4,8.21E-06                                            n,1060,.775,2.15593612 ngen,2,6,1033,1034,1,,.16
! element real constants                                  fill,1039,1060,3,1045,5 r,1,.25                                                    fill,1035,1039 r,2,.1875                                                  fill,1041,1045,3,1042,1,4,5 r,3,.375                                                  n,1064,1.245,2.03 r,4,.075                                                  fill,1060,1064 r,5,,1e9,,1                                                n,1092,-.065,2.98 r,6,-15,1e9,-.036                                          n,1096,.77960172,2.76 r,7,15,1e9,-.036                                          fill r,8,0,1e9,,1                                              n,1100,1.245,2.76 r,9,1,1,1                                                  fill,1096,1100 r,10,1e2                                                  fill,1056,1092,3,1065,9,9,1 r,101,-180.000,1e5,,1                                      ngen,3,9,1098,1100,1,,.26 r,102,-177.444,1e5,,1                                      n,1146,.14020351,4.4 r,103,-174.888,1e5,,1                                      fill,1092,1146,5,1101,9 r,104,-172.333,1e5,,1                                      n,1164,.14020351,4.98 r,105,-169.777,1e5,,1                                      fill,1146,1164,1,1155 r,106,-167.221,1e5,,1                                      local,11,,39.13520351,54.98,,-86.15 r,107,-164.665,1e5,,1                                      n,1168 r,108,-162.109,1e5,,1                                      n,1159,.3 r,109,-159.553,1e5,,1                                      ngen,3,-1,1159,1159,,,-.125 r,110,-156.998,1e5,,1                                      n,1148,.58,-.25 r,111,-154.442,1e5,,1                                      ngen,2,-18,1157,1159,1,.56 r,112,-141.553,1e5,,1                                      ngen,2,-9,1139,1141,1,.25 r,113,-128.665,1e5,,1                                      ngen,2,-27,1148,1148,,.81 r,114,-115.777,1e5,,1                                      ngen,2,-18,1130,1132,1,.56 r,115,-102.888,1e5,,1                                      fill,1096,1114,1,1105 r,116,-90.0000,1e5,,1                                      csys,12 r,130,-102.000,1e5,,1                                      fill,1101,1105 r,136,-77.1520,1e5,,1                                      fill,1110,1112,1,1111,,6,9 2.10.1-17
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 fill,1164,1168                              ngen,2,-879,1003,1003 fill,122,124
! nodes for the upper seal flange            ngen,2,-1870,2003,2003 local,11,,38.405,52.81                      n,135,38.53,63.78649751 n,2001,,5                                    fill,133,135 n,2005,.25,5                                local,12,1,29.905,63.78649751 fill                                        n,140,8.625,64.23984399 ngen,3,5,2001,2005,1,,-.25                  fill,135,140 n,2031,,3.45                                local,14,1,,1.8125 n,2035,.91,3.45                              n,150,77.4375,90 fill                                        fill,140,150 fill,2011,2031,3,2016,5,5,1 n,2051,,2.543442101                          ! nodes for the OCA outer shell n,2055,.91,2.543442101                      csys fill                                        n,601 fill,2031,2051,3,2036,5,4,1                  n,613,47.0625 n,2040,.91,3.29                              fill fill,2040,2055,2,2045,5                      n,622,47.0625,46.7775 n,2059,1.345,2.66                            fill,613,622 fill,2055,2059                              n,630,47.0625,47.6325 n,2071,,2.17                                n,638,47.0625,75.3440689 n,2073,.21504507,2.17                        fill,630,638 fill                                        local,15,1,40.5625,75.3440689 n,2077,.74504507,2.17                        n,640,6.5,62.55238078 fill,2073,2077                              fill,638,640 fill,2051,2071,1,2060                        local,16,1,,-2.75 fill,2054,2076,1,2065                        n,650,94.5,90 fill,2060,2065                              fill,640,650 n,2081,1.345,2.17 fill,2077,2081                              ! nodes for the polyurethane foam inner surface fill,2055,2077,1,2066,,5,1                  csys n,2107,.85759646,.54                        ngen,2,100,101,150,1 n,2109,1.10488343,.54                        n,125,38.58338729,50.9 fill                                        n,232,38.53,56.26 n,2111,1.345,.54 fill,2109,2111                              ! nodes for the polyurethane foam outer surface fill,2077,2107,5,2082,5,5,1                  ngen,2,-100,601,650,1 n,2117,.94488343 n,2119,1.10488343                            ! intermediate polyurethane foam nodes fill                                        fill,201,501,2,301,100,22,1 fill,2109,2119,1,2114                        n,300,43.9375,50.9 n,2112,.870715847,.35                        n,331,41.5375,51.8825 fill,2112,2114                              n,332,41.5375,56.26 n,2120,1.345,3.45                            n,422,43.9375,46.7775 n,2121,1.345,3.29                            n,430,44.2375,47.6375 ngen,2,51,2071,2073,1,,-.305                n,431,44.2375,51.8825 ngen,2,3,2122,2124,1,,-.305                  fill,222,422,1,322 fill,223,300,1,323
! nodes for the locking ring                fill,332,532,1,432 local,11,,39.35,51.29                        fill,233,533,2,333,100,18,1 n,3001 n,3005,.435                                  ! nodes for the z-flanges fill                                        ngen,2,279,422,422,0 n,3009,.935                                  ngen,2,402,300,300,0 fill,3005,3009                              ngen,2,273,430,430,0 n,3037,,.81                                  rp2,,,1,1 n,3041,.435,.693442101                      ngen,2,374,331,331,0 fill                                        rp2,,,1,1 n,3045,.935,.693442101 fill,3041,3045                              ! elements for the lower seal flange fill,3001,3037,3,3010,9,9,1                  type,1 n,3145,,4.11                                mat,1 n,3149,.435,4.226557899                      real,1 fill                                        e,1001,1002,1007,1006 n,3153,.935,4.226557899                      rp4,1,1,1,1 fill,3149,3153                              egen,5,5,1,4,1 fill,3041,3149,11,3050,9,5,1                e,1026,1027,1036,1035 n,3181,,4.67                                e,1027,1028,1036 n,3185,.535,4.67                            e,1028,1029,1037,1036 fill                                        e,1029,1030,1031,1037 n,3189,.935,4.67                            e,1031,1032,1038,1037 fill,3185,3189                              rp3,1,1,1,1 fill,3145,3181,3,3154,9,9,1                  e,1035,1036,1042,1041 rp4,1,1,1,1
! nodes for the OCA inner shell (OCV)        e,1041,1042,1047,1046 local,11,1,,84.5                            rp4,1,1,1,1 n,101,74.25,-90                              egen,3,5,32,35,1 n,111,74.25,-64.44174492                    e,1056,1057,1066,1065 fill                                        rp4,1,1,1,1 local,12,1,28.3125,24.29659664              egen,4,9,44,47,1 n,116,8.625                                  mat,2 fill,111,116                                e,1060,1061,1070,1069 csys                                        rp4,1,1,1,1
!n,117,36.9375,25.79659664                  egen,4,9,60,63,1 n,122,36.9375,43.95292590                    egen,3,9,74,75,1 fill,116,122                                egen,3,9,56,59,1 2.10.1-18
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 egen,7,9,84,85,1                                type,3 egen,3,1,99,99                                  mat,3 egen,3,1,93,93                                  real,1 e,201,301,302,202
! elements for the upper seal flange            rp22,1,1,1,1 type,1                                          e,224,223,323 mat,1                                          e,301,401,402,302 real,1                                          rp21,1,1,1,1 e,2006,2007,2002,2001                          e,322,422,300,323 rp4,1,1,1,1                                    e,300,125,224,323 egen,10,5,104,107,1                            e,401,501,502,402 e,2040,2121,2120,2035                          rp21,1,1,1,1 e,2060,2061,2052,2051                          e,333,233,232,332 e,2061,2062,2052                                e,233,333,334,234 e,2062,2063,2053,2052                          rp17,1,1,1,1 e,2063,2064,2053                                e,331,431,432,332 e,2064,2065,2054,2053                          rp19,1,1,1,1 rp6,1,1,1,1                                    e,430,530,531,431 e,2071,2072,2061,2060                          rp20,1,1,1,1 rp10,1,1,1,1 e,2122,2123,2072,2071                          ! interface elements between the steel shells rp2,1,1,1,1                                    !  and the polyurethane foam e,2125,2126,2123,2122                          type,5 rp2,1,1,1,1                                    mat,1 e,2082,2083,2078,2077                          real,101 rp4,1,1,1,1                                    e,101,201 egen,6,5,169,172,1                              real,102 egen,3,5,189,190,1                              e,102,202 real,103
! elements for the locking ring                e,103,203 type,1                                          real,104 mat,2                                          e,104,204 real,1                                          real,105 e,3001,3002,3011,3010                          e,105,205 rp4,1,1,1,1                                    real,106 egen,4,9,197,200,1                              e,106,206 mat,1                                          real,107 e,3005,3006,3015,3014                          e,107,207 rp4,1,1,1,1                                    real,108 egen,20,9,213,216,1                            e,108,208 e,3145,3146,3155,3154                          real,109 rp4,1,1,1,1                                    e,109,209 egen,4,9,293,296,1                              real,110 e,110,210
! elements for the OCA inner shell (OCV)        real,111 type,2                                          e,111,211 mat,1                                          real,112 real,1                                          e,112,212 e,101,102                                      real,113 rp16,1,1                                        e,113,213 real,2                                          real,114 e,117,118                                      e,114,214 rp5,1,1                                        real,115 real,1                                          e,115,215 e,122,123                                      real,116 e,123,1003                                      e,116,216 e,2003,134                                      rp5,1,1 e,134,135                                      real,130 rp16,1,1                                        e,122,222 rp2,1,1
! elements for the OCA outer shell              e,1003,224 real,1                                          real,101 e,601,602                                      e,702,300 rp18,1,1                                        e,701,422 real,3                                          e,622,522 e,619,620                                      real,150 rp3,1,1                                        e,706,332 e,630,631                                      e,705,331 rp8,1,1                                        e,704,431 real,1                                          e,703,430 e,638,639                                      e,630,530 rp12,1,1                                        real,116 e,300,702
! elements for the Z-flanges                    e,422,701 real,4                                          e,706,332 e,622,701                                      e,705,331 e,701,702                                      e,704,431 e,702,1034                                      e,703,430 e,1034,1033                                    e,2003,233 e,630,703                                      e,134,234 e,703,704                                      rp2,1,1 rp3,1,1                                        real,136 e,706,2120                                      e,136,236 e,2120,2035                                    real,137 e,137,237
! polyurethane foam elements                    real,138 2.10.1-19
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 e,138,238                                                e,1001,1002 real,139                                                  rp4,1,1 e,139,239 real,140                                                  ! couple the upper shell to the upper seal flange e,140,240                                                type,6 real,141                                                  mat,4 e,141,241                                                real,9 real,142                                                  e,2001,2002 e,142,242                                                rp4,1,1 real,143 e,143,243                                                ! springs between the lower seal flange real,144                                                  !  and the locking ring e,144,244                                                type,7 real,145                                                  mat,1 e,145,245                                                real,10 real,146                                                  e,3038,1061 e,146,246                                                rp3,1,1 real,147 e,147,247                                                ! springs between the upper seal flange real,148                                                  !  and the locking ring e,148,248                                                type,7 real,149                                                  mat,1 e,149,249                                                real,10 real,150                                                  e,2056,3146 e,150,250                                                rp3,1,1 real,101 e,501,601                                                ! springs between the lower seal flange rp13,1,1                                                  !  and the upper seal flange real,116                                                  type,7 e,513,613                                                mat,1 rp10,1,1                                                  real,10 e,530,630                                                e,1164,2073 rp9,1,1                                                  rp5,1,1 real,639 e,539,639                                                ! displacement constraints real,640                                                  d,101,UX,0,,601,500,rotz e,540,640                                                d,201,UX,0,,501,100 real,641                                                  d,150,UX,0,,650,500,rotz e,541,641                                                d,250,UX,0,,550,100 real,642                                                  d,3099,UY,0 e,542,642                                                d,all,uz,0 real,643 e,543,643                                                ! pressure loads real,644                                                  alls e,544,644                                                pload=+(14.7-14.7) real,645                                                  p,101,102,pload,,122,1 e,545,645                                                p,123,1003,pload real,646                                                  p,1001,1006,pload,,1021,5 e,546,646                                                p,1026,1035,pload real,647                                                  p,1035,1041,pload e,547,647                                                p,1041,1046,pload,,1051,5 real,648                                                  p,1056,1065,pload,,1155,9 e,548,648                                                p,1164,1165,pload,,1167,1 real,649                                                  p,1168,1159,pload e,549,649                                                p,2077,2082,pload real,150                                                  p,2073,2074,pload,,2076,1 e,550,650                                                p,2127,2124,pload p,2124,2073,pload
! interface elements between the lower seal flange        p,2125,2126,pload,,2126,1
!  and the locking ring                                  p,2122,2125,pload type,4                                                    p,2071,2122,pload mat,1                                                    p,2001,2006,pload,,2046,5 real,6                                                    p,2051,2060,pload e,3038,1061                                              p,2060,2071,pload rp3,1,1                                                  p,2003,134,pload p,134,135,pload,,149,1
! interface elements between the upper seal flange
!  and the locking ring                                  ! delete unused nodes at seal flange interfaces type,4                                                    ndele,124 mat,1                                                    ndele,133 real,7 e,2056,3146                                              ! solve the problem rp3,1,1                                                  fini
                                                          /solu
! interface elements between the lower seal flange        neqit,1000
!  and the upper seal flange                            alls type,5                                                    solv mat,1                                                    fini real,8                                                    save e,1164,2073 rp5,1,1                                                  ! post-process the problem
                                                          /post1
! couple the lower shell to the lower seal flange        set type,6                                                    rsys,solu mat,4                                                    ernorm,0 real,9 2.10.1-20
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
! table stress definitions for shell elements        /com, nall                                                /com,+++++++++++++++++++++++++++++++++++++++
alls                                                /com,+ OCV torispherical head crown shells +
esel,s,type,,2                                      /com,+++++++++++++++++++++++++++++++++++++++
etab,sit,nmisc,4                                    /com, etab,sim,nmisc,9                                    /com, etab,sib,nmisc,14                                    nall eall
/com,                                                esel,s,elem,,339,348,1    ! upper head
/com,                                                esel,a,elem,,309,318,1    ! lower head
/com,                                                pret
/com,+++++++++++++++++++++
/com,+ lower seal flange +                          /com,
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,
/com,                                                /com,+++++++++++++++++++++++++++++++++++++++++
nall                                                /com,+ OCV torispherical head knuckle shells +
eall                                                /com,+++++++++++++++++++++++++++++++++++++++++
nsel,s,node,,1000,1999,1                            /com, prns,prin                                            /com, nall
/com,                                                eall
/com,                                                esel,s,elem,,334,338,1    ! upper head
/com,                                                esel,a,elem,,319,323,1    ! lower head
/com,+++++++++++++++++++++                          pret
/com,+ upper seal flange +
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,
/com,                                                /com, nall                                                /com,++++++++++++++++++++++++++++++++++
eall                                                /com,+ OCA outer shells and z-flanges +
nsel,s,node,,2000,2999,1                            /com,++++++++++++++++++++++++++++++++++
prns,prin                                            /com,
                                                    /com,
/com,                                                nall
/com,                                                eall
/com,                                                esel,s,elem,,349,399,1
/com,++++++++++++++++                                pret
/com,+ locking ring +
/com,++++++++++++++++                                /com,
/com,                                                /com,
/com,                                                /com, nall                                                /com,++++++++++++++++++++++++++++++
eall                                                /com,+ polyurethane foam elements +
nsel,s,node,,3000,3999,1                            /com,++++++++++++++++++++++++++++++
prns,prin                                            /com,
                                                    /com,
/com,                                                nall
/com,                                                eall
/com,                                                esel,s,elem,,415,559,1
/com,++++++++++++++++++++++++++++++++++++++          prns,prin
/com,+ OCV cylindrical and conical shells +
/com,++++++++++++++++++++++++++++++++++++++          ! finalize ANSYS
/com,                                                nall
/com,                                                eall nall                                                save eall                                                /out,term esel,s,elem,,324,331,1                              /eof pret
/com,
/com, 2.10.1-21
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 Table 2.10.1 ANSYS Input Listing for OCA Load Case 4
! initialize ANSYS                                        r,137,-64.3041,1e5,,1 fini                                                      r,138,-51.4561,1e5,,1
/cle                                                      r,139,-38.6081,1e5,,1
/filename,oca_lc4,inp                                      r,140,-25.7602,1e5,,1
/out,,txt                                                  r,141,-23.1841,1e5,,1 r,142,-20.6081,1e5,,1
! start preprocessing the model                            r,143,-18.0321,1e5,,1
/prep7                                                    r,144,-15.4561,1e5,,1
/title, OCA Load Case 4: P=0.0/14.7 psia, T=70/70 F        r,145,-12.8801,1e5,,1 r,146,-10.3041,1e5,,1
! element types                                            r,147,-7.72805,1e5,,1 et,1,42,,,1                                                r,148,-5.15203,1e5,,1 et,2,51                                                    r,149,-2.57602,1e5,,1 et,3,42,,,1                                                r,150,,1e5,,1 et,4,12,,,,,,,1                                            r,639,-58.7238,1e5,,1 et,5,12,,,,,,,1                                            r,640,-27.4476,1e5,,1 et,6,3                                                    r,641,-24.7029,1e5,,1 et,7,14,,,2                                                r,642,-21.9581,1e5,,1 r,643,-19.2133,1e5,,1
! reference and uniform temperatures                      r,644,-16.4686,1e5,,1 tref,70                                                    r,645,-13.7238,1e5,,1 tunif,70                                                  r,646,-10.9790,1e5,,1 r,647,-8.23429,1e5,,1
! material properties for non-slotted steel regions        r,648,-5.48952,1e5,,1 ex,1,28.3e06                                              r,649,-2.74476,1e5,,1 nuxy,1,.3 alpx,1,8.46e-06                                            ! nodes for the lower seal flange local,11,,38.24941495,50.051977923,,-12
! material properties for slotted steel regions            n,1001 ex,2,14.15e06                                              n,1005,.25 ey,2,14.15e06                                              fill ez,2,1                                                    n,1016,,.58677836 nuxy,2,.3                                                  n,1020,.25,.58677836 nuxz,2,0                                                  fill nuyz,2,0                                                  fill,1001,1016,2,1006,5,5,1 alpx,2,8.46e-06                                            n,1026,,.896632635 alpy,2,8.46e-06                                            local,12,,38.505,50 alpz,2,8.46e-06                                            move,1026,11,0,999,0,12,-.065,999,0 fill,1016,1026,1,1021
! material properties for the polyurethane foam            local,11,1,39.12699808,50.47 ex,3,4773                                                  n,1025,.5,148.5 ey,3,6810                                                  n,1030,.5,129 ez,3,4773                                                  n,1031,.5,109.5 nuxy,3,.33                                                n,1032,.5,90 nuxz,3,.33                                                csys,12 nuyz,3,.33                                                fill,1021,1025,3,1022,1,2,5 alpx,3,3.5e-5                                              n,1033,.775,.97 n,1034,1.145,.97
! material properties for the rigid coupling elements      n,1076,-.065,2.98 ex,4,28.3e06                                              fill,1026,1076,8,1035,5 nuxy,4,.3                                                  fill,1035,1076,7,1041,5 alpx,4,8.46E-06                                            n,1060,.775,2.15593612 ngen,2,6,1033,1034,1,,.16
! element real constants                                  fill,1039,1060,3,1045,5 r,1,.25                                                    fill,1035,1039 r,2,.1875                                                  fill,1041,1045,3,1042,1,4,5 r,3,.375                                                  n,1064,1.245,2.03 r,4,.075                                                  fill,1060,1064 r,5,,1e9,,1                                                n,1092,-.065,2.98 r,6,-15,1e9,-.036                                          n,1096,.77960172,2.76 r,7,15,1e9,-.036                                          fill r,8,0,1e9,,1                                              n,1100,1.245,2.76 r,9,1,1,1                                                  fill,1096,1100 r,10,1e2                                                  fill,1056,1092,3,1065,9,9,1 r,101,-180.000,1e5,,1                                      ngen,3,9,1098,1100,1,,.26 r,102,-177.444,1e5,,1                                      n,1146,.14020351,4.4 r,103,-174.888,1e5,,1                                      fill,1092,1146,5,1101,9 r,104,-172.333,1e5,,1                                      n,1164,.14020351,4.98 r,105,-169.777,1e5,,1                                      fill,1146,1164,1,1155 r,106,-167.221,1e5,,1                                      local,11,,39.13520351,54.98,,-86.15 r,107,-164.665,1e5,,1                                      n,1168 r,108,-162.109,1e5,,1                                      n,1159,.3 r,109,-159.553,1e5,,1                                      ngen,3,-1,1159,1159,,,-.125 r,110,-156.998,1e5,,1                                      n,1148,.58,-.25 r,111,-154.442,1e5,,1                                      ngen,2,-18,1157,1159,1,.56 r,112,-141.553,1e5,,1                                      ngen,2,-9,1139,1141,1,.25 r,113,-128.665,1e5,,1                                      ngen,2,-27,1148,1148,,.81 r,114,-115.777,1e5,,1                                      ngen,2,-18,1130,1132,1,.56 r,115,-102.888,1e5,,1                                      fill,1096,1114,1,1105 r,116,-90.0000,1e5,,1                                      csys,12 r,130,-102.000,1e5,,1                                      fill,1101,1105 r,136,-77.1520,1e5,,1                                      fill,1110,1112,1,1111,,6,9 2.10.1-22
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 fill,1164,1168                              ngen,2,-879,1003,1003 fill,122,124
! nodes for the upper seal flange            ngen,2,-1870,2003,2003 local,11,,38.405,52.81                      n,135,38.53,63.78649751 n,2001,,5                                    fill,133,135 n,2005,.25,5                                local,12,1,29.905,63.78649751 fill                                        n,140,8.625,64.23984399 ngen,3,5,2001,2005,1,,-.25                  fill,135,140 n,2031,,3.45                                local,14,1,,1.8125 n,2035,.91,3.45                              n,150,77.4375,90 fill                                        fill,140,150 fill,2011,2031,3,2016,5,5,1 n,2051,,2.543442101                          ! nodes for the OCA outer shell n,2055,.91,2.543442101                      csys fill                                        n,601 fill,2031,2051,3,2036,5,4,1                  n,613,47.0625 n,2040,.91,3.29                              fill fill,2040,2055,2,2045,5                      n,622,47.0625,46.7775 n,2059,1.345,2.66                            fill,613,622 fill,2055,2059                              n,630,47.0625,47.6325 n,2071,,2.17                                n,638,47.0625,75.3440689 n,2073,.21504507,2.17                        fill,630,638 fill                                        local,15,1,40.5625,75.3440689 n,2077,.74504507,2.17                        n,640,6.5,62.55238078 fill,2073,2077                              fill,638,640 fill,2051,2071,1,2060                        local,16,1,,-2.75 fill,2054,2076,1,2065                        n,650,94.5,90 fill,2060,2065                              fill,640,650 n,2081,1.345,2.17 fill,2077,2081                              ! nodes for the polyurethane foam inner surface fill,2055,2077,1,2066,,5,1                  csys n,2107,.85759646,.54                        ngen,2,100,101,150,1 n,2109,1.10488343,.54                        n,125,38.58338729,50.9 fill                                        n,232,38.53,56.26 n,2111,1.345,.54 fill,2109,2111                              ! nodes for the polyurethane foam outer surface fill,2077,2107,5,2082,5,5,1                  ngen,2,-100,601,650,1 n,2117,.94488343 n,2119,1.10488343                            ! intermediate polyurethane foam nodes fill                                        fill,201,501,2,301,100,22,1 fill,2109,2119,1,2114                        n,300,43.9375,50.9 n,2112,.870715847,.35                        n,331,41.5375,51.8825 fill,2112,2114                              n,332,41.5375,56.26 n,2120,1.345,3.45                            n,422,43.9375,46.7775 n,2121,1.345,3.29                            n,430,44.2375,47.6375 ngen,2,51,2071,2073,1,,-.305                n,431,44.2375,51.8825 ngen,2,3,2122,2124,1,,-.305                  fill,222,422,1,322 fill,223,300,1,323
! nodes for the locking ring                fill,332,532,1,432 local,11,,39.35,51.29                        fill,233,533,2,333,100,18,1 n,3001 n,3005,.435                                  ! nodes for the z-flanges fill                                        ngen,2,279,422,422,0 n,3009,.935                                  ngen,2,402,300,300,0 fill,3005,3009                              ngen,2,273,430,430,0 n,3037,,.81                                  rp2,,,1,1 n,3041,.435,.693442101                      ngen,2,374,331,331,0 fill                                        rp2,,,1,1 n,3045,.935,.693442101 fill,3041,3045                              ! elements for the lower seal flange fill,3001,3037,3,3010,9,9,1                  type,1 n,3145,,4.11                                mat,1 n,3149,.435,4.226557899                      real,1 fill                                        e,1001,1002,1007,1006 n,3153,.935,4.226557899                      rp4,1,1,1,1 fill,3149,3153                              egen,5,5,1,4,1 fill,3041,3149,11,3050,9,5,1                e,1026,1027,1036,1035 n,3181,,4.67                                e,1027,1028,1036 n,3185,.535,4.67                            e,1028,1029,1037,1036 fill                                        e,1029,1030,1031,1037 n,3189,.935,4.67                            e,1031,1032,1038,1037 fill,3185,3189                              rp3,1,1,1,1 fill,3145,3181,3,3154,9,9,1                  e,1035,1036,1042,1041 rp4,1,1,1,1
! nodes for the OCA inner shell (OCV)        e,1041,1042,1047,1046 local,11,1,,84.5                            rp4,1,1,1,1 n,101,74.25,-90                              egen,3,5,32,35,1 n,111,74.25,-64.44174492                    e,1056,1057,1066,1065 fill                                        rp4,1,1,1,1 local,12,1,28.3125,24.29659664              egen,4,9,44,47,1 n,116,8.625                                  mat,2 fill,111,116                                e,1060,1061,1070,1069 csys                                        rp4,1,1,1,1
!n,117,36.9375,25.79659664                  egen,4,9,60,63,1 n,122,36.9375,43.95292590                    egen,3,9,74,75,1 fill,116,122                                egen,3,9,56,59,1 2.10.1-23
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 egen,7,9,84,85,1                                type,3 egen,3,1,99,99                                  mat,3 egen,3,1,93,93                                  real,1 e,201,301,302,202
! elements for the upper seal flange            rp22,1,1,1,1 type,1                                          e,224,223,323 mat,1                                          e,301,401,402,302 real,1                                          rp21,1,1,1,1 e,2006,2007,2002,2001                          e,322,422,300,323 rp4,1,1,1,1                                    e,300,125,224,323 egen,10,5,104,107,1                            e,401,501,502,402 e,2040,2121,2120,2035                          rp21,1,1,1,1 e,2060,2061,2052,2051                          e,333,233,232,332 e,2061,2062,2052                                e,233,333,334,234 e,2062,2063,2053,2052                          rp17,1,1,1,1 e,2063,2064,2053                                e,331,431,432,332 e,2064,2065,2054,2053                          rp19,1,1,1,1 rp6,1,1,1,1                                    e,430,530,531,431 e,2071,2072,2061,2060                          rp20,1,1,1,1 rp10,1,1,1,1 e,2122,2123,2072,2071                          ! interface elements between the steel shells rp2,1,1,1,1                                    !  and the polyurethane foam e,2125,2126,2123,2122                          type,5 rp2,1,1,1,1                                    mat,1 e,2082,2083,2078,2077                          real,101 rp4,1,1,1,1                                    e,101,201 egen,6,5,169,172,1                              real,102 egen,3,5,189,190,1                              e,102,202 real,103
! elements for the locking ring                e,103,203 type,1                                          real,104 mat,2                                          e,104,204 real,1                                          real,105 e,3001,3002,3011,3010                          e,105,205 rp4,1,1,1,1                                    real,106 egen,4,9,197,200,1                              e,106,206 mat,1                                          real,107 e,3005,3006,3015,3014                          e,107,207 rp4,1,1,1,1                                    real,108 egen,20,9,213,216,1                            e,108,208 e,3145,3146,3155,3154                          real,109 rp4,1,1,1,1                                    e,109,209 egen,4,9,293,296,1                              real,110 e,110,210
! elements for the OCA inner shell (OCV)        real,111 type,2                                          e,111,211 mat,1                                          real,112 real,1                                          e,112,212 e,101,102                                      real,113 rp16,1,1                                        e,113,213 real,2                                          real,114 e,117,118                                      e,114,214 rp5,1,1                                        real,115 real,1                                          e,115,215 e,122,123                                      real,116 e,123,1003                                      e,116,216 e,2003,134                                      rp5,1,1 e,134,135                                      real,130 rp16,1,1                                        e,122,222 rp2,1,1
! elements for the OCA outer shell              e,1003,224 real,1                                          real,101 e,601,602                                      e,702,300 rp18,1,1                                        e,701,422 real,3                                          e,622,522 e,619,620                                      real,150 rp3,1,1                                        e,706,332 e,630,631                                      e,705,331 rp8,1,1                                        e,704,431 real,1                                          e,703,430 e,638,639                                      e,630,530 rp12,1,1                                        real,116 e,300,702
! elements for the Z-flanges                    e,422,701 real,4                                          e,706,332 e,622,701                                      e,705,331 e,701,702                                      e,704,431 e,702,1034                                      e,703,430 e,1034,1033                                    e,2003,233 e,630,703                                      e,134,234 e,703,704                                      rp2,1,1 rp3,1,1                                        real,136 e,706,2120                                      e,136,236 e,2120,2035                                    real,137 e,137,237
! polyurethane foam elements                    real,138 2.10.1-24
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 e,138,238                                                e,1001,1002 real,139                                                  rp4,1,1 e,139,239 real,140                                                  ! couple the upper shell to the upper seal flange e,140,240                                                type,6 real,141                                                  mat,4 e,141,241                                                real,9 real,142                                                  e,2001,2002 e,142,242                                                rp4,1,1 real,143 e,143,243                                                ! springs between the lower seal flange real,144                                                  !  and the locking ring e,144,244                                                type,7 real,145                                                  mat,1 e,145,245                                                real,10 real,146                                                  e,3038,1061 e,146,246                                                rp3,1,1 real,147 e,147,247                                                ! springs between the upper seal flange real,148                                                  !  and the locking ring e,148,248                                                type,7 real,149                                                  mat,1 e,149,249                                                real,10 real,150                                                  e,2056,3146 e,150,250                                                rp3,1,1 real,101 e,501,601                                                ! springs between the lower seal flange rp13,1,1                                                  !  and the upper seal flange real,116                                                  type,7 e,513,613                                                mat,1 rp10,1,1                                                  real,10 e,530,630                                                e,1164,2073 rp9,1,1                                                  rp5,1,1 real,639 e,539,639 real,640                                                  ! displacement constraints e,540,640                                                d,101,UX,0,,601,500,rotz real,641                                                  d,201,UX,0,,501,100 e,541,641                                                d,150,UX,0,,650,500,rotz real,642                                                  d,250,UX,0,,550,100 e,542,642                                                d,3099,UY,0 real,643                                                  d,all,uz,0 e,543,643 real,644                                                  ! pressure loads e,544,644                                                alls real,645                                                  pload=+(0.0-14.7) e,545,645                                                p,101,102,pload,,122,1 real,646                                                  p,123,1003,pload e,546,646                                                p,1001,1006,pload,,1021,5 real,647                                                  p,1026,1035,pload e,547,647                                                p,1035,1041,pload real,648                                                  p,1041,1046,pload,,1051,5 e,548,648                                                p,1056,1065,pload,,1155,9 real,649                                                  p,1164,1165,pload,,1167,1 e,549,649                                                p,1168,1159,pload real,150                                                  p,2077,2082,pload e,550,650                                                p,2073,2074,pload,,2076,1 p,2127,2124,pload
! interface elements between the lower seal flange        p,2124,2073,pload
!  and the locking ring                                  p,2125,2126,pload,,2126,1 type,4                                                    p,2122,2125,pload mat,1                                                    p,2071,2122,pload real,6                                                    p,2001,2006,pload,,2046,5 e,3038,1061                                              p,2051,2060,pload rp3,1,1                                                  p,2060,2071,pload p,2003,134,pload
! interface elements between the upper seal flange        p,134,135,pload,,149,1
!  and the locking ring type,4                                                    ! delete unused nodes at seal flange interfaces mat,1                                                    ndele,124 real,7                                                    ndele,133 e,2056,3146 rp3,1,1                                                  ! solve the problem fini
! interface elements between the lower seal flange        /solu
!  and the upper seal flange                            neqit,1000 type,5                                                    alls mat,1                                                    solv real,8                                                    fini e,1164,2073                                              save rp5,1,1
                                                          ! post-process the problem
! couple the lower shell to the lower seal flange        /post1 type,6                                                    set mat,4                                                    rsys,solu real,9                                                    ernorm,0 2.10.1-25
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
                                                    /com,
! table stress definitions for shell elements        /com, nall                                                /com,+++++++++++++++++++++++++++++++++++++++
alls                                                /com,+ OCV torispherical head crown shells +
esel,s,type,,2                                      /com,+++++++++++++++++++++++++++++++++++++++
etab,sit,nmisc,4                                    /com, etab,sim,nmisc,9                                    /com, etab,sib,nmisc,14                                    nall eall
/com,                                                esel,s,elem,,339,348,1    ! upper head
/com,                                                esel,a,elem,,309,318,1    ! lower head
/com,                                                pret
/com,+++++++++++++++++++++
/com,+ lower seal flange +                          /com,
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,
/com,                                                /com,+++++++++++++++++++++++++++++++++++++++++
nall                                                /com,+ OCV torispherical head knuckle shells +
eall                                                /com,+++++++++++++++++++++++++++++++++++++++++
nsel,s,node,,1000,1999,1                            /com, prns,prin                                            /com, nall
/com,                                                eall
/com,                                                esel,s,elem,,334,338,1    ! upper head
/com,                                                esel,a,elem,,319,323,1    ! lower head
/com,+++++++++++++++++++++                          pret
/com,+ upper seal flange +
/com,+++++++++++++++++++++                          /com,
/com,                                                /com,
/com,                                                /com, nall                                                /com,++++++++++++++++++++++++++++++++++
eall                                                /com,+ OCA outer shells and z-flanges +
nsel,s,node,,2000,2999,1                            /com,++++++++++++++++++++++++++++++++++
prns,prin                                            /com,
                                                    /com,
/com,                                                nall
/com,                                                eall
/com,                                                esel,s,elem,,349,399,1
/com,++++++++++++++++                                pret
/com,+ locking ring +
/com,++++++++++++++++                                /com,
/com,                                                /com,
/com,                                                /com, nall                                                /com,++++++++++++++++++++++++++++++
eall                                                /com,+ polyurethane foam elements +
nsel,s,node,,3000,3999,1                            /com,++++++++++++++++++++++++++++++
prns,prin                                            /com,
                                                    /com,
/com,                                                nall
/com,                                                eall
/com,                                                esel,s,elem,,415,559,1
/com,++++++++++++++++++++++++++++++++++++++          prns,prin
/com,+ OCV cylindrical and conical shells +
/com,++++++++++++++++++++++++++++++++++++++          ! finalize ANSYS
/com,                                                nall
/com,                                                eall nall                                                save eall                                                /out,term esel,s,elem,,324,331,1                              /eof pret
/com, 2.10.1-26
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 Table 2.10.1 ANSYS Input Listing for ICV Load Case 1
! initialize ANSYS                                        n,1138,.3,-.25 fini                                                      fill
/cle                                                      n,1122,.86
/filename,icv_lc1,inp                                      n,1120,.86,-.25
/out,,txt                                                  fill n,1113,1.11
! start preprocessing the model                            n,1111,1.11,-.25
/prep7                                                    fill
/title, ICV Load Case 1: P=64.7/3.5 psia, T=160/160 F      n,1095,1.67 n,1093,1.67,-.25
! element types                                            fill et,1,42,,,1                                                csys,11 et,2,51                                                    n,1145,.205,5.5 et,3,12,,,,,,,1                                            fill,1127,1145,1,1136 et,4,12,,,,,,,1                                            n,1149,.695,5.5 et,5,3                                                    fill,1145,1149 et,6,14,,,2                                                fill,1120,1138,1,1129 fill,1093,1111,1,1102
! reference and uniform temperatures                      fill,1077,1095,1,1086 tref,160                                                  fill,1091,1093,,,,6,9 tunif,160                                                  fill,1073,1091,1,1082,,5,1 ngen,3,9,1079,1081,1,,.26
! material properties for non-slotted steel regions ex,1,27.8e6                                                ! nodes for the upper seal ring nuxy,1,.3                                                  n,2001,-.035,4.89 alpx,1,8.694e-6                                            n,2003,.180045070,4.89 fill
! material properties for slotted steel regions            n,2007,-0.035,5.5 ex,2,13.9e6                                                n,2009,.180045070,5.5 ey,2,13.9e6                                                fill ez,2,1                                                    fill,2001,2007,1,2004,,3,1 nuxy,2,.3                                                  n,2013,.710045070,5.5 nuyz,2,0                                                  fill,2009,2013 nuxz,2,0                                                  n,2017,1.31,5.5 alpx,2,8.694e-6                                            fill,2013,2017 alpy,2,8.694e-6                                            n,2040,-0.035,5.98 alpz,2,8.694e-6                                            fill,2007,2040,2,2018,11 n,2035,0.875,5.873442101
! material properties for the rigid coupling elements      fill,2029,2035 ex,3,27.8e6                                                n,2039,1.31,5.99 nuxy,3,.3                                                  fill,2035,2039 alpx,3,8.694e-6                                            fill,2008,2030,1,2019,,10,1 n,2042,.245,5.98
! element real constants                                  fill,2040,2042 r,1,.25                                                    n,2043,.390419704,6.008925778 r,2,-15,1e9,-.036                                          n,2044,.513700577,6.091299423 r,3,15,1e9,-.036                                          n,2049,.596074222,6.214580296 r,4,0,1e9,-.01                                            n,2054,.625,6.36 r,5,1,1,1                                                  n,2058,.875,6.36 r,10,1e2                                                  fill fill,2035,2058,2,2048,5
! nodes for the lower seal ring                            fill,2044,2048 local,11,0,36.315,45.08954245                              fill,2049,2053 n,1001                                                    ngen,5,5,2054,2058,1,,.1875 n,1005,.25                                                n,2104,.822596460,3.87 fill                                                      n,2106,1.07,3.87 n,1016,,.575                                              fill n,1020,.25,.575                                            n,2116,1.07,3.33 fill                                                      fill,2106,2116,1,2111 fill,1001,1016,2,1006,5,5,1                                n,2108,1.31,3.87 n,1031,,1.48                                              fill,2106,2108 n,1035,.84,1.48                                            fill,2013,2104,5,2079,5,5,1 fill                                                      n,2109,.835715950,3.68 fill,1016,1031,2,1021,5,5,1                                fill,2109,2111 n,1046,,2.6759361                                          n,2114,.909883430,3.33 n,1050,.84,2.67593612                                      fill,2114,2116 fill fill,1031,1046,2,1036,5,5,1                                ! nodes for the locking ring n,1054,1.31,2.55                                          local,13,0,37.225,46.89954245 fill,1050,1054                                            n,3001 n,1073,,3.5                                                n,3005,.435 n,1077,.844601720,3.28                                    fill fill                                                      n,3008,.789412 n,1079,1.095,3.28                                          fill,3005,3008 fill,1077,1079                                            n,3037,,.81 n,1081,1.31,3.28                                          n,3041,.435,.693442101 fill,1079,1081                                            fill fill,1046,1073,2,1055,9,9,1                                n,3045,.935,.693442101 n,1127,.205,4.92                                          fill,3041,3045 fill,1073,1127,5,1082,9                                    fill,3001,3037,3,3010,9,8,1 local,12,,37.01020351,50.58954246,,-86.15                  n,3027,.935,.4 n,1140,.3                                                  fill,3008,3027,1,3018 2.10.1-27
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 fill,3027,3045,1,3036                    real,1 n,3101,,4.11                              e,3001,3002,3011,3010 n,3105,.435,4.226557898                  rp4,1,1,1,1 fill                                      egen,4,9,173,176,1 n,3109,.935,4.226557899                  mat,1 fill,3105,3109                            e,3005,3006,3015,3014 fill,3041,3105,11,3046,5,5,1              rp3,1,1,1,1 n,3137,,4.67                              e,3018,3017,3008 n,3141,.435,4.67                          e,3014,3015,3024,3023 fill                                      rp4,1,1,1,1 n,3144,.789412,4.67                      egen,3,9,193,196,1 fill,3141,3144                            e,3041,3042,3047,3046 fill,3101,3137,3,3110,9,8,1              rp4,1,1,1,1 fill,3109,3144,3,3118,9                  egen,11,5,205,208,1 e,3096,3097,3106,3105
! nodes for the lower shell              rp4,1,1,1,1 local,14,1,,73.25                        e,3101,3102,3111,3110 n,4001,73.25,-90                          rp8,1,1,1,1 n,4016,73.25,-64.50665929                egen,4,9,253,259,1 fill                                      e,3117,3118,3127,3126 local,15,1,27.815,14.9171927              e,3126,3127,3136,3135 n,4025,8.625                              e,3135,3136,3144,3144 fill,4016,4025 csys,0                                    ! elements for the lower shell n,4081,36.44,45.08954245                  type,2 fill,4025,4081                            mat,1 n,4001,0,0                                real,1 e,4001,4002
! nodes for the upper shell              rp79,1,1 local,16,1,,-5.75                        e,4080,1003 n,5001,74.5,90 n,5016,74.5,64.42280563                  ! elements for the upper shell fill                                      type,2 local,17,1,28.44,53.66954245              mat,1 n,5025,8.625                              real,1 fill,5016,5025                            e,2076,5026 csys,0                                    e,5026,5025 n,5027,37.065,52.16954245                rp25,-1,-1 fill,5025,5027 n,5001,0,68.75                            ! interface elements between the lower seal flange
                                          !  and the locking ring
! elements for the lower seal ring        type,3 type,1                                    mat,1 mat,1                                    real,2 real,1                                    e,3038,1051 e,1001,1002,1007,1006                    rp3,1,1 rp4,1,1,1,1 egen,9,5,1,4,1                            ! interface elements between the upper seal flange e,1046,1047,1056,1055                    !  and the locking ring rp4,1,1,1,1                              type,3 egen,5,9,37,40,1                          mat,1 egen,7,9,53,54,1                          real,3 egen,3,27,55,56,1                        e,2036,3102 mat,2                                    rp3,1,1 e,1050,1051,1060,1059 rp4,1,1,1,1                              ! interface elements between the lower seal flange egen,3,9,73,76,1                          !  and the upper seal flange egen,3,9,83,84,1                          type,4 mat,1
! elements for the upper seal ring        real,4 type,1                                    e,1145,2009 mat,1                                    rp5,1,1 real,1 e,2001,2002,2005,2004                    ! couple the lower shell to the lower seal flange rp2,1,1,1,1                              type,5 egen,2,3,89,90,1                          mat,3 e,2007,2008,2019,2018                    real,5 rp10,1,1,1,1                              e,1001,1002 egen,2,11,93,102,1                        rp4,1,1 egen,2,11,103,107,1 e,2046,2045,2034                          ! couple the upper shell to the upper seal flange rp2,1,1,0                                type,5 e,2034,2035,2048,2047                    mat,3 e,2044,2045,2050,2049                    real,5 rp4,1,1,1,1                              e,2074,2075 egen,6,5,121,124,1                        rp4,1,1 e,2079,2080,2014,2013 rp4,1,1,1,1                              ! springs between the lower seal flange e,2084,2085,2080,2079                    !  and the locking ring rp4,1,1,1,1                              type,6 egen,5,5,149,152,1                        mat,1 egen,3,5,165,166,1                        real,10 e,3038,1051
! elements for the locking ring          rp3,1,1 type,1 mat,2                                    ! springs between the upper seal flange 2.10.1-28
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022
!  and the locking ring                            /com, type,6                                              /com, mat,1                                                /com,+++++++++++++++++++++
real,10                                              /com,+ upper seal flange +
e,2036,3102                                          /com,+++++++++++++++++++++
rp3,1,1                                              /com,
                                                    /com,
! springs between the lower seal flange              nall
!  and the upper seal flange                        eall type,6                                              nsel,s,node,,2000,2999,1 mat,1                                                esln real,10                                              prns,prin e,1145,2009 rp5,1,1                                              /com,
                                                    /com,
! displacement constraints                          /com, d,4001,ux,0,,5001,1000,rotz                          /com,++++++++++++++++
d,3075,uy,0                                          /com,+ locking ring +
                                                    /com,++++++++++++++++
! pressure loads                                    /com, pload=+(64.7-3.5)                                    /com, alls                                                nall p,4001,4002,pload,,4079,1                            eall p,4080,1003,pload                                    nsel,s,node,,3000,3999,1 p,1001,1006,pload,,1041,5                            esln p,1046,1055,pload,,1136,9                            prns,prin p,1145,1146,pload,,1148,9 p,1140,1149,pload                                    /com, p,2001,2002,pload,,2002,1                            /com, p,2003,2006,pload,,2006,3                            /com, p,2009,2010,pload,,2012,1                            /com,++++++++++++++++++++++
p,2013,2079,pload                                    /com,+ cylindrical shells +
p,2001,2004,pload,,2004,3                            /com,++++++++++++++++++++++
p,2007,2018,pload,,2029,11                          /com, p,2040,2041,pload,,2043,1                            /com, p,2044,2049,pload,,2069,5                            esel,s,elem,,309,366,1 p,5001,5002,pload,,5025,1                            pret p,5026,2076,pload
                                                    /com,
! solve the problem                                  /com, fini                                                /com,
/solu                                                /com,+++++++++++++++++++++++++++++++++++
neqit,1000                                          /com,+ torispherical head crown shells +
alls                                                /com,+++++++++++++++++++++++++++++++++++
solv                                                /com, fini                                                /com, save                                                esel,s,elem,,376,390,1    ! upper head esel,a,elem,,285,299,1    ! lower head
! post-process the problem                          pret
/post1 set                                                  /com, rsys,solu                                            /com, ernorm,0                                            /com,
                                                    /com,+++++++++++++++++++++++++++++++++++++
! table stress definitions for shell elements        /com,+ torispherical head knuckle shells +
nall                                                /com,+++++++++++++++++++++++++++++++++++++
alls                                                /com, esel,s,type,,2                                      /com, etab,sit,nmisc,4                                    esel,s,elem,,367,375,1    ! upper head etab,sim,nmisc,9                                    esel,a,elem,,300,308,1    ! lower head etab,sib,nmisc,14                                    pret
/com,                                                ! finalize ANSYS
/com,                                                nall
/com,                                                eall
/com,+++++++++++++++++++++                          save
/com,+ lower seal flange +                          /out,term
/com,+++++++++++++++++++++                          /eof
/com,
/com, nall eall nsel,s,node,,1000,1999,1 esln prns,prin
/com, 2.10.1-29
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 Table 2.10.1 ANSYS Input Listing for ICV Load Case 2
! initialize ANSYS                                        n,1138,.3,-.25 fini                                                      fill
/cle                                                      n,1122,.86
/filename,icv_lc2,inp                                      n,1120,.86,-.25
/out,,txt                                                  fill n,1113,1.11
! start preprocessing the model                            n,1111,1.11,-.25
/prep7                                                    fill
/title, ICV Load Case 2: P=0.0/14.7 psia, T=70/70 F        n,1095,1.67 n,1093,1.67,-.25
! element types                                            fill et,1,42,,,1                                                csys,11 et,2,51                                                    n,1145,.205,5.5 et,3,12,,,,,,,1                                            fill,1127,1145,1,1136 et,4,12,,,,,,,1                                            n,1149,.695,5.5 et,5,3                                                    fill,1145,1149 et,6,14,,,2                                                fill,1120,1138,1,1129 fill,1093,1111,1,1102
! reference and uniform temperatures                      fill,1077,1095,1,1086 tref,70                                                    fill,1091,1093,,,,6,9 tunif,70                                                  fill,1073,1091,1,1082,,5,1 ngen,3,9,1079,1081,1,,.26
! material properties for non-slotted steel regions ex,1,28.3e6                                                ! nodes for the upper seal ring nuxy,1,.3                                                  n,2001,-.035,4.89 alpx,1,8.46e-6                                            n,2003,.180045070,4.89 fill
! material properties for slotted steel regions            n,2007,-0.035,5.5 ex,2,14.15e6                                              n,2009,.180045070,5.5 ey,2,14.15e6                                              fill ez,2,1                                                    fill,2001,2007,1,2004,,3,1 nuxy,2,.3                                                  n,2013,.710045070,5.5 nuyz,2,0                                                  fill,2009,2013 nuxz,2,0                                                  n,2017,1.31,5.5 alpx,2,8.46e-6                                            fill,2013,2017 alpy,2,8.46e-6                                            n,2040,-0.035,5.98 alpz,2,8.46e-6                                            fill,2007,2040,2,2018,11 n,2035,0.875,5.873442101
! material properties for the rigid coupling elements      fill,2029,2035 ex,3,28.3e6                                                n,2039,1.31,5.99 nuxy,3,.3                                                  fill,2035,2039 alpx,3,8.46e-6                                            fill,2008,2030,1,2019,,10,1 n,2042,.245,5.98
! element real constants                                  fill,2040,2042 r,1,.25                                                    n,2043,.390419704,6.008925778 r,2,-15,1e9,-.036                                          n,2044,.513700577,6.091299423 r,3,15,1e9,-.036                                          n,2049,.596074222,6.214580296 r,4,0,1e9,-.01                                            n,2054,.625,6.36 r,5,1,1,1                                                  n,2058,.875,6.36 r,10,1e2                                                  fill fill,2035,2058,2,2048,5
! nodes for the lower seal ring                            fill,2044,2048 local,11,0,36.315,45.08954245                              fill,2049,2053 n,1001                                                    ngen,5,5,2054,2058,1,,.1875 n,1005,.25                                                n,2104,.822596460,3.87 fill                                                      n,2106,1.07,3.87 n,1016,,.575                                              fill n,1020,.25,.575                                            n,2116,1.07,3.33 fill                                                      fill,2106,2116,1,2111 fill,1001,1016,2,1006,5,5,1                                n,2108,1.31,3.87 n,1031,,1.48                                              fill,2106,2108 n,1035,.84,1.48                                            fill,2013,2104,5,2079,5,5,1 fill                                                      n,2109,.835715950,3.68 fill,1016,1031,2,1021,5,5,1                                fill,2109,2111 n,1046,,2.6759361                                          n,2114,.909883430,3.33 n,1050,.84,2.67593612                                      fill,2114,2116 fill fill,1031,1046,2,1036,5,5,1                                ! nodes for the locking ring n,1054,1.31,2.55                                          local,13,0,37.225,46.89954245 fill,1050,1054                                            n,3001 n,1073,,3.5                                                n,3005,.435 n,1077,.844601720,3.28                                    fill fill                                                      n,3008,.789412 n,1079,1.095,3.28                                          fill,3005,3008 fill,1077,1079                                            n,3037,,.81 n,1081,1.31,3.28                                          n,3041,.435,.693442101 fill,1079,1081                                            fill fill,1046,1073,2,1055,9,9,1                                n,3045,.935,.693442101 n,1127,.205,4.92                                          fill,3041,3045 fill,1073,1127,5,1082,9                                    fill,3001,3037,3,3010,9,8,1 local,12,,37.01020351,50.58954246,,-86.15                  n,3027,.935,.4 n,1140,.3                                                  fill,3008,3027,1,3018 2.10.1-30
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 fill,3027,3045,1,3036                    real,1 n,3101,,4.11                              e,3001,3002,3011,3010 n,3105,.435,4.226557898                  rp4,1,1,1,1 fill                                      egen,4,9,173,176,1 n,3109,.935,4.226557899                  mat,1 fill,3105,3109                            e,3005,3006,3015,3014 fill,3041,3105,11,3046,5,5,1              rp3,1,1,1,1 n,3137,,4.67                              e,3018,3017,3008 n,3141,.435,4.67                          e,3014,3015,3024,3023 fill                                      rp4,1,1,1,1 n,3144,.789412,4.67                      egen,3,9,193,196,1 fill,3141,3144                            e,3041,3042,3047,3046 fill,3101,3137,3,3110,9,8,1              rp4,1,1,1,1 fill,3109,3144,3,3118,9                  egen,11,5,205,208,1 e,3096,3097,3106,3105
! nodes for the lower shell              rp4,1,1,1,1 local,14,1,,73.25                        e,3101,3102,3111,3110 n,4001,73.25,-90                          rp8,1,1,1,1 n,4016,73.25,-64.50665929                egen,4,9,253,259,1 fill                                      e,3117,3118,3127,3126 local,15,1,27.815,14.9171927              e,3126,3127,3136,3135 n,4025,8.625                              e,3135,3136,3144,3144 fill,4016,4025 csys,0                                    ! elements for the lower shell n,4081,36.44,45.08954245                  type,2 fill,4025,4081                            mat,1 n,4001,0,0                                real,1 e,4001,4002
! nodes for the upper shell              rp79,1,1 local,16,1,,-5.75                        e,4080,1003 n,5001,74.5,90 n,5016,74.5,64.42280563                  ! elements for the upper shell fill                                      type,2 local,17,1,28.44,53.66954245              mat,1 n,5025,8.625                              real,1 fill,5016,5025                            e,2076,5026 csys,0                                    e,5026,5025 n,5027,37.065,52.16954245                rp25,-1,-1 fill,5025,5027 n,5001,0,68.75                            ! interface elements between the lower seal flange
                                          !  and the locking ring
! elements for the lower seal ring        type,3 type,1                                    mat,1 mat,1                                    real,2 real,1                                    e,3038,1051 e,1001,1002,1007,1006                    rp3,1,1 rp4,1,1,1,1 egen,9,5,1,4,1                            ! interface elements between the upper seal flange e,1046,1047,1056,1055                    !  and the locking ring rp4,1,1,1,1                              type,3 egen,5,9,37,40,1                          mat,1 egen,7,9,53,54,1                          real,3 egen,3,27,55,56,1                        e,2036,3102 mat,2                                    rp3,1,1 e,1050,1051,1060,1059 rp4,1,1,1,1                              ! interface elements between the lower seal flange egen,3,9,73,76,1                          !  and the upper seal flange egen,3,9,83,84,1                          type,4 mat,1
! elements for the upper seal ring        real,4 type,1                                    e,1145,2009 mat,1                                    rp5,1,1 real,1 e,2001,2002,2005,2004                    ! couple the lower shell to the lower seal flange rp2,1,1,1,1                              type,5 egen,2,3,89,90,1                          mat,3 e,2007,2008,2019,2018                    real,5 rp10,1,1,1,1                              e,1001,1002 egen,2,11,93,102,1                        rp4,1,1 egen,2,11,103,107,1 e,2046,2045,2034                          ! couple the upper shell to the upper seal flange rp2,1,1,0                                type,5 e,2034,2035,2048,2047                    mat,3 e,2044,2045,2050,2049                    real,5 rp4,1,1,1,1                              e,2074,2075 egen,6,5,121,124,1                        rp4,1,1 e,2079,2080,2014,2013 rp4,1,1,1,1                              ! springs between the lower seal flange e,2084,2085,2080,2079                    !  and the locking ring rp4,1,1,1,1                              type,6 egen,5,5,149,152,1                        mat,1 egen,3,5,165,166,1                        real,10 e,3038,1051
! elements for the locking ring          rp3,1,1 type,1 mat,2                                    ! springs between the upper seal flange 2.10.1-31
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022
!  and the locking ring                            nsel,s,node,,2000,2999,1 type,6                                              esln mat,1                                                prns,prin real,10 e,2036,3102                                          /com, rp3,1,1                                              /com,
                                                    /com,
! springs between the lower seal flange              /com,++++++++++++++++
!  and the upper seal flange                        /com,+ locking ring +
type,6                                              /com,++++++++++++++++
mat,1                                                /com, real,10                                              /com, e,1145,2009                                          nall rp5,1,1                                              eall nsel,s,node,,3000,3999,1
! displacement constraints                          esln d,4001,ux,0,,5001,1000,rotz                          prns,prin d,3075,uy,0
                                                    /com,
! pressure loads                                    /com, pload=+(0.0-14.7)                                    /com, alls                                                /com,++++++++++++++++++++++
p,4001,4002,pload,,4079,1                            /com,+ cylindrical shells +
p,4080,1003,pload                                    /com,++++++++++++++++++++++
p,1001,1006,pload,,1041,5                            /com, p,1046,1055,pload,,1136,9                            /com, p,1145,1146,pload,,1148,9                            esel,s,elem,,309,366,1 p,1140,1149,pload                                    pret p,2001,2002,pload,,2002,1 p,2003,2006,pload,,2006,3                            /com, p,2009,2010,pload,,2012,1                            /com, p,2013,2079,pload                                    /com, p,2001,2004,pload,,2004,3                            /com,+++++++++++++++++++++++++++++++++++
p,2007,2018,pload,,2029,11                          /com,+ torispherical head crown shells +
p,2040,2041,pload,,2043,1                            /com,+++++++++++++++++++++++++++++++++++
p,2044,2049,pload,,2069,5                            /com, p,5001,5002,pload,,5025,1                            /com, p,5026,2076,pload                                    esel,s,elem,,376,390,1    ! upper head esel,a,elem,,285,299,1    ! lower head
! solve the problem                                  pret fini
/solu                                                /com, neqit,1000                                          /com, alls                                                /com, solv                                                /com,+++++++++++++++++++++++++++++++++++++
fini                                                /com,+ torispherical head knuckle shells +
save                                                /com,+++++++++++++++++++++++++++++++++++++
                                                    /com,
! post-process the problem                          /com,
/post1                                              esel,s,elem,,367,375,1    ! upper head set                                                  esel,a,elem,,300,308,1    ! lower head rsys,solu                                            pret ernorm,0
                                                    ! finalize ANSYS
! table stress definitions for shell elements        nall nall                                                eall alls                                                save esel,s,type,,2                                      /out,term etab,sit,nmisc,4                                    /eof etab,sim,nmisc,9 etab,sib,nmisc,14
/com,
/com,
/com,
/com,+++++++++++++++++++++
/com,+ lower seal flange +
/com,+++++++++++++++++++++
/com,
/com, nall eall nsel,s,node,,1000,1999,1 esln prns,prin
/com,
/com,
/com,
/com,+++++++++++++++++++++
/com,+ upper seal flange +
/com,+++++++++++++++++++++
/com,
/com, nall eall 2.10.1-32
 
HalfPACT Safety Analysis Report              Rev. 9, August 2022 Figure 2.10.1 OCA FEA Model Element Plot 2.10.1-33
 
HalfPACT Safety Analysis Report              Rev. 9, August 2022 Figure 2.10.1 ICV FEA Model Element Plot 2.10.1-34
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 2.10.2 Elastomer O-ring Seal Performance Tests 2.10.2.1 Introduction Each containment O-ring seal material formulation shall be initially qualified for use in the HalfPACT packaging through the application of performance tests that demonstrate the materials ability to achieve and maintain a leaktight 1 seal at or beyond extremes for temperature, duration, minimum seal compression, and maximum seal compression change in a prototypical test fixture.
The basis for formulation qualification test conditions applicable to the HalfPACT packaging is provided in Section 2.10.2.2, Limits of O-ring Seal Compression and Temperature. Section 2.10.2.3, Formulation Qualification Test Fixture and Procedure, defines the test fixture and test procedure for O-ring seal material qualification tests. Section 2.10.2.4, Rainier Rubber R0405-70 Formulation Qualification Test Results, summarizes the results of qualification testing successfully performed on Rainier Rubber 2 butyl rubber compound R0405-70.
Each batch of containment O-ring seal material shall additionally be required to satisfy the requirements of ASTM D2000 3 M4AA710 A13 B13 F17 F48 Z Trace Element. Section 2.10.2.5, ASTM D2000 Standardized Batch Material Tests, summarizes the industry standardized batch tests and correlates the ASTM D2000 designator to specific O-ring performance characteristics.
Additional information regarding past containment O-ring seal testing is presented in the report Design Development and Certification Testing of the TRUPACT-II Package 4.
2.10.2.2 Limits of O-ring Seal Compression and Temperature 2.10.2.2.1 Inner Containment Vessel Containment O-ring Seal Compression The inner containment vessel (ICV) closure seal configuration consists of two O-ring seals, each located on a slightly different diameter in the ICV lid due to the tapered bore (see Appendix 1.3.1, Packaging General Arrangement Drawings, Sheets 5 and 6 of 12, for dimensional details).
The upper O-ring seal is defined as the containment boundary, and the lower O-ring seal provides an annulus in which to establish a vacuum for leak testing.
In order to determine the minimum compression that may occur for the ICV containment O-ring seal, the worst-case tolerance stack-up on the lid flange, body flange, locking ring, and O-ring seal dimensions are utilized with the upper and lower seal flanges offset relative to each other.
Figure 2.10.2-1 depicts the O-ring seal flange geometry for minimum ICV containment O-ring seal compression (note the reference datum for calculations).
1 Leaktight is defined as leakage of 1 x 10-7 standard cubic centimeters per second (scc/sec), air, or less, per Section 5.4(3), Reference Air Leakage Rate, of ANSI N14.5-1997, American National Standard for Radioactive Materials -
Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
2 Rainier Rubber Company, Seattle, WA.
3 ASTM D2000-08, Standard Classification System for Rubber Products in Automotive Applications, American Society for Testing and Materials, Philadelphia, PA, Volume 09.02, 2008.
4 S. A. Porter, et al, Design Development and Certification Testing of the TRUPACT-II Package, 016-03-09, Portemus Engineering, Inc., Puyallup, Washington.
2.10.2-1
 
HalfPACT Safety Analysis Report                                                            Rev. 9, August 2022 With reference to Figure 2.10.2-1, the following dimensions define the worst-case configuration for determining the minimum ICV containment O-ring seal compression:
a = 0.153 inches (maximum vertical gap; see Section 8.2.3.3.2.3, Axial Play) b = 0.493 inches (minimum tab width; see Section 8.2.3.3.2.2, Tab Widths) c = 0.561 inches (maximum groove width; see Section 8.2.3.3.2.1, Groove Widths) dL = 0.251 inches (maximum vertical offset (gage depth); see Figure 8.2-4) dU = 0.249 inches (minimum vertical offset (ball diameter); see Figure 8.2-1) e = 0.330 inches (maximum seal groove offset; based on 0.300 +/- 0.030) f = 0.000 inches (minimum horizontal gap between upper and lower seal flange; closed) r = 0.125 inches (nominal lower seal flange tab edge radius) h = 0.253 inches (maximum O-ring seal groove depth; based on 0.250 +/- 0.003) w = 0.563 inches (maximum O-ring seal groove width; based on 0.560 +/- 0.003)
    = 3.60&#xba; (minimum lower flange tab angle; based on 3.85&#xba; +/- 0.25&#xba;)
    = 4.20&#xba; (maximum upper flange seal surface angle; based on 3.95&#xba; +/- 0.25&#xba;)
    = 3.60&#xba; (contact surfaces angle based on the average of angles  and )
    = 5.00&#xba; (maximum O-ring seal groove angle; based on 0&#xba; - 5&#xba;)
: 1. Worst-Case Location for the Center-Bottom of the O-ring Seal Groove With reference to Figure 2.10.2-1, the worst-case location for the center-bottom of the O-ring seal groove is determined by finding the horizontal and vertical distance from the datum to the O-ring seal contact point on the lower seal flange, xi and yi, respectively:
dL                          w x i = f + b +  e              + (h ) tan(  ) +  sin ()  (h ) cos() = 0.264494 inches cos()                        2 dL                          w y i = a + d L +  e              + (h ) tan(  ) +  cos () + (h ) sin() = 0.801270 inches cos()                              2
: 2. Worst-Case Location for O-ring Seal Contact on the Upper Flange Sealing Surface With reference to Figure 2.10.2-1, the worst-case location for O-ring seal contact on the upper seal flange sealing surface is determined by finding the horizontal and vertical distance from the datum to the O-ring seal contact point on the upper seal flange, xo and yo, respectively:
c y i + ( x i ) tan() +            dU tan()
xo =                                        = 0.599877 inches 1
                                                      + tan()
tan()
xo  c yo = d U +              = 0.778404 inches tan()
2.10.2-2
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022
: 3. Maximum O-ring Seal Groove-to-Contact Surface Gap The maximum O-ring seal groove-to-contact surface gap is determined by using the distance formula in two-dimensional Cartesian space:
g=    (x o  x i )2 + (y o  y i )2 = 0.336162 inches
: 4. Minimum O-ring Seal Cross-Sectional Diameter Due to Stretch The minimum reduced O-ring seal cross-sectional diameter, dcsr, is determined by finding the maximum ICV containment O-ring seal groove diameter, Dg, calculating the O-ring seal stretch, s, and calculating the corresponding maximum reduction in O-ring seal cross-sectional diameter, rcs, using worst-case dimensions.
Given a maximum lower seal flange control diameter, DL = 74.185 inches (based on 74.155 +/-
0.030), and a minimum lower seal flange control height, HL = 0.970 inches (based on 1.000 +/-
0.030), the maximum ICV containment O-ring seal groove diameter, Dg, is:
w D g = D L  2H L  e + (h ) tan(  ) +  cos () tan( )  (h ) cos() = 73.637517 inches 2
Given a minimum ICV containment O-ring seal inside diameter, Di = 70.070 inches (based on 71.500 +/- 2%), the maximum ICV containment O-ring stretch, s, is Dg  Di s=              = 5.09%
Di The maximum reduction in O-ring seal cross-sectional diameter, rcs, due to stretch (from Figure 3-3 of the Parker O-ring Handbook 5) is calculated with the stretch, s = 5.09:
rcs = 0.56 + 0.59s  0.0046s 2 = 3.44%
Given a minimum ICV containment O-ring seal cross-sectional diameter, ds = 0.390 inches (based on 0.400 +/- 0.010), the resulting reduced O-ring seal cross-sectional diameter, dcsr, is:
d csr = d s (1  rcs ) = 0.376584 inches
: 5. Minimum O-ring Seal Compression with an Offset Lid The minimum ICV containment O-ring seal compression, , is:
d csr  g
                                            =              = 10.73%
d csr The minimum O-ring seal compression is 10.73% with an offset lid. This is the worst case possible as a result of the HAC free drop.
5 ORD 5700, Parker O-ring Handbook, 2007, Parker Hannifin Corporation, Cleveland, OH.
2.10.2-3
 
HalfPACT Safety Analysis Report                                                              Rev. 9, August 2022
: 6. Minimum O-ring Seal Compression with a Centered Lid With reference to Figure 2.10.2-1, the centered position for the lower seal flange relative to the upper seal flange occurs when point  on the lower seal flange is moved to the midpoint between points  and . Calculate the x-locations for points  and :
x1 = b  (d L  r[1  sin()]) tan() = 0.484579 inches x 2 = c + (a + r[1  sin()]  d U ) tan() = 0.562553 inches Half the difference between the x1 and x2 values centers the lower seal flange tab within the upper seal flange groove (i.e., the ICV lid is centered in the ICV body). The centered horizontal offset, fc, is:
x1  x 2 fc =              = 0.038987 inches 2
Recalculate the O-ring seal gap, gc, based on the lid centered relative to the body:
dL                            w x ci = f c + b +  e              + (h ) tan(  ) +  sin ()  (h ) cos() = 0.303481 inches cos()                                2 dL                            w y ci = a + d L +  e              + (h ) tan(  ) +  cos () + (h ) sin() = 0.801270 inches cos()                                2 c
y ci + ( x ci ) tan() +              dU tan()
x co =                                              = 0.6000071 inches 1
                                                        + tan()
tan()
x co  c y co = d U +                = 0.781046 inches tan()
gc =    (x co  x ci )2 + (y co  y ci )2  = 0.297279 inches Knowing that the ICV containment O-ring seal groove diameter, Dg, and correspondingly the O-ring seal stretch, s, and the reduced O-ring seal cross-sectional diameter, dcsr, are the same, the minimum ICV containment O-ring seal compression, c:
d csr  g c c =                = 21.06%
d csr The minimum O-ring seal compression is 21.06% with a centered lid. This is the normal, as-installed configuration, since the presence of the O-ring seal will inherently self-center the lid.
2.10.2-4
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022
: 7. Maximum Change in O-ring Seal Compression from a Centered Lid to an Offset Lid The maximum resulting change in compression, , resulting in a minimally compressed ICV containment O-ring seal is:
                                              =  c  = 10.33%
This is the maximum change in compression of the O-ring seal as a result of the HAC free drop.
2.10.2.2.2 Containment O-ring Seal Qualification Temperature Per Section 3.4.3, Minimum Temperatures, the minimum ICV containment O-ring seal temperature is -40 &#xba;F for normal conditions of transport (NCT) and -20 &#xba;F for hypothetical accident conditions (HAC). Per Table 3.4-1 in Section 3.4.2, Maximum Temperatures, the maximum ICV O-ring seal temperature for NCT is 150 &#xba;F. The duration of O-ring seal material exposure to elevated temperatures under NCT can conservatively be assumed as one year based on the replacement frequency of the O-ring seals. Per Section 3.5.3, Package Temperatures, the maximum ICV O-ring seal temperature for HAC is projected to be 290 &#xba;F. Time-history temperature data was not acquired during certification testing of the HalfPACT package. Based on their similarity, the time-history of the TRUPACT-II package OCV O-ring seal temperatures provided in Figure 3.5-6 for Certification Test Unit 1 (CTU-1) and Figure 3.5-10 for Certification Test Unit 2 (CTU-2) from the TRUPACT-II SAR 6 may be used. The duration of ICV O-ring seal material exposure to elevated temperatures within 90% of the reported 290 &#xba;F maximum is conservatively estimated to be less than 12 hours.
An Arrhenius correlation for butyl material with an activation energy of 80 kJ/mol for butyl rubber has been developed to account for diffusion limited oxidation effects. 7 Use of the Arrhenius correlation allows the effects of both NCT and HAC elevated temperature/duration conditions identified above to be conservatively enveloped by a single, 360 &#xba;F, 8-hour test.
Based on the above evaluations, the minimum O-ring seal qualification test parameters required for initial formulation testing of ICV containment O-ring seal materials is summarized in Table 2.10.2-1.
6 U.S. Department of Energy (DOE), Safety Analysis Report for the TRUPACT-II Shipping Package, USNRC Certificate of Compliance 71-9218, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
7 K. T. Gillen, C. Mathias, and M. R. Keenan, Methods for Predicting More Confident Lifetimes of Seals in Air Environments, SAND99-0553J, Sandia National Laboratories, March 1999.
2.10.2-5
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 Table 2.10.2 Formulation Qualification Test O-ring Seal Compression Parameters Required Required              Required          Required          Temperature Simulated            Compression          Compression      Temperature              Duration Condition                    (%)            Change (%)              (&#xba;F)              (hours)
NCT Cold                  21.06                  N/A              -40                N/A HAC Free Drop                                      10.33            -20                N/A 10.73 HAC Fire                                          N/A              360                  8 2.10.2.3 Formulation Qualification Test Fixture and Procedure A bore-type test fixture shall be used to test the containment O-ring seal, representative of the bore seal configuration of the HalfPACT packaging. The fixture shall include an inner disk containing two, side-by-side O-ring seal grooves. An O-ring seal of prototypic cross-section for the ICV and butyl material, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings, shall be placed into each seal groove, and the assembly then placed within a mating bore component. The test fixture shall employ jacking screws or equivalent devices to displace the disk radially relative to the bore, affecting the required O-ring compression on one side of the test fixture. Figure 2.10.2-2 conceptually illustrates the O-ring seal test fixture.
The sizes of all sealing components and O-ring seals utilized in the test fixture, including the amount of O-ring seal stretch, may be adjusted along with the amount of radial displacement to ensure that the parameters in Table 2.10.2-1 can be achieved. The test fixtures overall diameter may be reduced relative to a full-scale HalfPACT package to achieve a practical size for testing.
A reduction in relative diameter is acceptable since the O-ring seal compression, compression change, and temperature are the parameters of primary importance relative to evaluating an O-ring materials ability to maintain a leaktight seal.
All test specimens may be coated lightly with vacuum grease prior to installation into the test fixture. The fully assembled test fixture shall be placed within an environmental test chamber for both heating and cooling with thermocouples attached to the fixture used to confirm the O-ring seal temperature.
The region between the two O-ring seals constitutes a test volume. To perform a leak test, the test volume shall be connected to a helium mass spectrometer leak detector, then evacuated to an appropriate level of vacuum and the outside of the test fixture surrounded with a contained and highly concentrated environment of helium gas, consistent with the guidelines of Appendix A, Section A.5.3, Gas Filled Envelope - Gas Detector, of ANSI N14.5 8. An O-ring seal test shall be successful if the leakage between the seals is 1 x 10-7 standard cubic centimeters per second (scc/sec), air, or less (i.e., leaktight).
8 ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
2.10.2-6
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 Test conditions shall be selected to simulate temperature/duration and minimum compression for the prototypic O-ring seals under NCT and HAC conditions. Each set of two test O-ring seals shall be subjected to an initial test at NCT Cold conditions with the inner disk offset as necessary to achieve the NCT required compression, to a second test at HAC Free Drop conditions with the inner disk initially positioned and then radially offset as necessary to achieve the HAC required compression and compression change magnitudes, to a third test at HAC Fire conditions after the required soak duration with the inner disk remaining offset, and to a fourth test at HAC Cold conditions with the inner disk remaining offset (see Table 2.10.2-1).
Helium leakage rate tests shall be performed at each cold temperature test configuration, either at
-40 &#xba;F for the NCT Cold condition case, or at -20 &#xba;F for all other cases. Helium leakage rate testing is not practical at hot condition temperatures due to the rapid permeation and saturation of helium gas through the elastomeric material at high temperatures; a fully saturated O-ring seal test specimen results in a measured leakage in excess of 1 x 10-7 scc/sec, air. In lieu of leakage rate testing at the hot temperature test configuration, the ability to establish a rapid, hard vacuum between the O-ring seals shall be used as the basis for acceptance at elevated temperatures, with leaktightness proven subsequent to the elevated temperature phase by the final leakage rate test at -20 &#xba;F. The duration of each of the cold temperature phases of the test shall be defined by the time required to achieve the requisite cold temperatures whereas the duration of the hot phase shall be defined by the required elevated temperature and associated temperature duration given in Table 2.10.2-1.
2.10.2.3.1 Formulation Qualification Test Procedure The process of formulation qualification leak testing O-ring seal material is given below.
: 1. Assemble the test fixture with two test O-ring seals.
: 2. Radially shift the disk inside the bore to establish reduced O-ring seal compression on one side of the test fixture, ensuring the NCT Cold compression requirements are met per Table 2.10.2-1.
: 3. Cool the test fixture to -40 &#xba;F, continuing to restrain the disk in the NCT offset position relative to the bore.
: 4. Perform a helium leakage rate test with the test fixture temperature at -40 &#xba;F.
: 5. Reposition the disk inside the bore to establish an appropriate starting position for the HAC Free Drop test with the test fixture temperature at -20 &#xba;F.
: 6. Radially shift the disk inside the bore to establish a reduced O-ring seal compression on one side of the test fixture, ensuring the HAC Cold compression and compression change requirements are met per Table 2.10.2-1.
: 7. Perform a helium leakage rate test with the test fixture temperature at -20 &#xba;F.
: 8. Warm the test fixture to the elevated test temperature (i.e., HAC Fire temperature per Table 2.10.2-1), continuing to restrain the disk in the HAC offset position relative to the bore.
: 9. Maintain the elevated temperature for 8-hour duration.
2.10.2-7
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022
: 10. At the end of the elevated temperature duration, confirm that a rapid, hard vacuum can be achieved and maintained in the test volume between the two, test O-ring seals at the elevated temperature.
: 11. Cool the test fixture to -20 &#xba;F, continuing to restrain the disk in the HAC offset position relative to the bore.
: 12. Perform a helium leakage rate test with the test fixture temperature at -20 &#xba;F.
2.10.2.4 Rainier Rubber R0405-70 Formulation Qualification Test Results Test results are summarized in Table 2.10.2-2, as referenced from GEN-REP-0001. 9 As shown in the table, the Rainier Rubber compound R0405-70 butyl rubber material is capable of maintaining a leaktight seal when subjected to worst-case seal compressions beyond the range of NCT and HAC cold and hot temperatures applicable to the HalfPACT package. For comparison, the minimum O-ring seal compression applicable for the NCT Cold condition (see Table 2.10.2-1) is 21.06% for the ICV. The NCT Cold tests summarized in Table 2.10.2-2 were conservatively performed with the disk in its full offset position, thus showing leaktight capability at NCT Cold conditions to as low as 10.38%. For the remaining tests, the applicable minimum compression is 10.73% for the ICV whereas the tests were all performed in the full offset position, thus showing leaktight capability to as low as 10.38%. For the HAC Free Drop test, the disk was initially centered and then shifted as much as 10.74%, which enveloped the applicable worst-case shift of 10.33% for the ICV. For the HAC Fire test, again per Table 2.10.2-1, a test temperature of at least 360 &#xba;F for at least 8 hours is applicable, whereas the actual test was conservatively performed at 400 &#xba;F for 8 hours, as noted in Table 2.10.2-2. Therefore, formulation qualification testing of Rainier Rubber compound R0405-70 bounds the minimum O-ring seal compressions for the HalfPACT package.
2.10.2.5 ASTM D2000 Standardized Batch Material Tests Based on successfully demonstrating the ability to remain leaktight when subject to the formulation qualification tests, Rainier Rubber R0405-70 butyl rubber compound was selected to benchmark material performance parameters that can be evaluated using available industry standardized tests. Correlation of the R0405-70 butyl rubber compound performance to industry standard performance specifications establishes a standard quality and performance benchmark that is suitable for use in material batch testing. Note that a formulation represents a controlled chemical recipe and production process as defined by the material supplier, a batch represents the chemical compounding of a production quantity of material before vulcanizing, and a lot refers to the quantity of finished product made at any one time.
Qualification testing identified certain key parameters that are important to seal performance. Of these, two important parameters for this application are resistance to helium permeation and acceptable resiliency at cold temperatures. Butyl rubber performs very well resisting helium permeation, and the 9
Formulation Qualification Testing of Rainier Rubber Butyl Compound RR0405-70, GEN-REP-0001, Rev. 0, Washington TRU Solutions, February 2010.
2.10.2-8
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 TR-10 test in ASTM D1329 10 provides an acceptable method for determining cold temperature material resiliency, with the properties of the R0405-70 acting as a baseline for the required resiliency.
The ability of the compound to withstand elevated temperatures while not having significant reduction in material properties is also required to maintain seal integrity after the hypothetical accident condition thermal event. Material properties in elastomers are reduced through the process of de-polymerization, an aging phenomenon. Elastomer aging can be accelerated by the application of energy (heat). The effect of aging can be quantified by measuring the reduction of physical properties after maintaining the seal material at an elevated temperature for a specific length of time. For the same amount of reduction in properties, a shorter time can be used at a higher temperature, or a longer time can be used at a lower temperature. ASTM D573 11 provides an acceptable method for determining the effects of temperature aging on elastomeric compounds.
ASTM D395 12 provides an acceptable method for determining the effects of compression set.
R0405-70 butyl rubber compound uses an acceptance criteria of less than 25% compression set for 22 hours at an elevated temperature of 70 &#xba;C.
ASTM D2137 13 provides an acceptable method for determining an elastomeric materials ability to withstand cold temperatures and remain pliable. Although the TR-10 test in ASTM D1329 demonstrates the seal materials resiliency at a much lower temperature, this test verifies the seal materials lack of brittleness at the minimum regulatory temperature of -40 &#xba;C.
Hardness or durometer along with tensile strength and elongation are defined and checked to ensure durability of the seal material during operation. ASTM D2240 14 provides an acceptable method for determining the required 70 +/-5 durometer, and ASTM D412 15 provides an acceptable method for determining the required minimum 10 MPa (1,450 psi) tensile strength and minimum 250% elongation, with the properties of the R0405-70 acting as a baseline for the required hardness, tensile strength, and elongation.
For proprietary seal materials that have fairly demanding requirements such as the R0405-70 butyl rubber compound, the compound is commonly specified by a company designator and subsequently checked against exacting performance standards. Specifying an elastomeric compound by its chemistry alone is difficult considering the sheer number of parameters that affect seal performance. However, by applying the above nationally recognized standards to a material batch, the important parameters are defined for verifying the performance of the seal material.
10 ASTM D1329-88 (re-approved 1998), Standard Test Method for Evaluating Rubber Property - Retraction at Lower Temperatures (TR Test), American Society for Testing and Materials, Philadelphia, PA, Volume 09.01, 2001.
11 ASTM D573-99, Standard Test Method for Rubber - Deterioration in an Air Oven, American Society for Testing and Materials, Philadelphia, PA, Volume 09.01, 2001.
12 ASTM D395-01, Standard Test Methods for Rubber Property - Compression Set, American Society for Testing and Materials, Philadelphia, PA, Volume 09.01, 2001.
13 ASTM D2137-94 (re-approved 2000), Standard Test Methods for Rubber Property - Brittleness Point of Flexible Polymers and Coated Fabrics, American Society for Testing and Materials, Philadelphia, PA, Volume 09.02, 2001.
14 ASTM D2240-00, Standard Test Method for Rubber Property - Durometer Hardness, American Society for Testing and Materials, Philadelphia, PA, Volume 09.01, 2002.
15 ASTM D412-98a, Standard Test Methods for Vulcanized Rubber and Thermoplastic Rubbers and Thermoplastic Elastomers - Tension, American Society for Testing and Materials, Philadelphia, PA, Volume 09.01, 2001.
2.10.2-9
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 ASTM D1414 16 is the standard method for testing O-ring seals, and covers most, but not all, of the required testing delineated above. However, due to the overall size of the O-ring seals and the additional testing specified, ASTM D20003 provides a better standard classification system.
Using the ASTM D2000 designator, O-ring seals with properties equivalent to R0405-70 butyl rubber material are classified as follows and summarized in the table below:
M4AA710 A13 B13 F17 F48 Z Trace Element Designator                                            Condition M                Metric units designator (default condition) 4              Grade 4 acceptance criteria for the tests specified AA                Butyl rubber compound 7              70 Shore A durometer hardness per ASTM D2240 10              Tensile strength and elongation per ASTM D 412; acceptance criteria are a minimum 10 MPa (1,450 psi) tensile strength and a minimum 250% elongation A13              Heat resistance test per ASTM D573; the acceptance criteria are a maximum 10 Shore A durometer hardness increase, a maximum reduction in tensile strength of 25%, and a maximum reduction in ultimate elongation of 25% at 70 &#xba;C B13              Compression set per Method B of ASTM D395; acceptance criterion is a maximum 25% compression set after 22 hours at 70 &#xba;C F17              Cold temperature resistance specifying low temperature brittleness per Method A, 9.3.2, of ASTM D2137; non-brittle after 3 minutes at -40 &#xba;C F48              Cold temperature resiliency, where F is for cold temperature resistance, and 4 specifies testing to the TR-10 test of ASTM D1329; 8 indicates a TR-10 temperature of -50 &#xba;C (-58 &#xba;F), or less Z Trace Element        Z designator allows specific notes to be added; Z Trace Element allows trace elements to be added to the elastomeric compound to meet the seal material requirements 16 ASTM D1414-94 (re-approved 1999), Standard Test Methods for Rubber O-Rings, American Society for Testing and Materials, Philadelphia, PA, Volume 09.02, 2001.
2.10.2-10
 
HalfPACT Safety Analysis Report                                                                                                  Rev. 9, August 2022 Table 2.10.2 Rainier Rubber R0405-70 Formulation Qualification O-ring Seal Test Results O-ring    Minimum Seal      O-ring O-ring                                Reduction    Seal O-ring Seal Seal                          O-ring  in Cross-    Cross-Cross-Sectional                                                                      Temperature for Leaktight Leak O-ring    Inside                          Seal  Sectional Sectional Diameter, dcs (in)                                  O-ring Seal Compression (%)      Test ( 8.8 x 10-8 scc/sec, He)
Test      Seal    Diameter,                      Stretch, Diameter, Diameter, Number  Number      Ds (in)    Max        Min    S (%)    R (%)    dcsr (in) Center Disk Offset Disk Change      -40 &#xba;F  -20 &#xba;F  400 &#xba;F    -20 &#xba;F 1      11.368      0.396      0.394    6.80      4.36      0.377      21.12        10.38      10.74 1                                                                                                                      Yes      Yes      Yes      Yes 4      11.500      0.396      0.392    5.58      3.71      0.377      21.12        10.38      10.74 2      11.417      0.396      0.395    6.34      4.12      0.379      21.54        10.85      10.69 2                                                                                                                      Yes      Yes      Yes      Yes 3      11.465      0.395      0.394    5.90      3.88      0.379      21.54        10.85      10.69 Notes:
The test fixtures pertinent dimensions are taken in line with the direction of offset, which is also the position where the minimum cross-sectional diameter of the O-ring seals are placed: bore inside diameter, Di = 12.736 inches; disk outside diameter, Do = 12.655 inches; and the O-ring seal groove diameter, Dg = 12.14125 inches (based on the average of fixture measurements taken along the axis of offset). All tests are performed using WTS Test Fixture No. 4.
Material for all O-ring seal test specimens is butyl rubber compound R0405-70, Rainier Rubber Co., Seattle, WA.
Given the O-ring seal inside diameter, Ds, the percent of O-ring seal stretch, S = 100 x (Dg - Ds)/Ds.
From Figure 3-3 of the Parker O-ring Handbook5 and based on the O-ring seal cross-sectional diameter, dcs, the percent reduction in O-ring seal cross-sectional diameter, R = -0.005 + 1.19S - 0.19S2 - 0.001S3 + 0.008S4 for 0  S  3%, and R = 0.56 + 0.59S - 0.0046S2 for 3% < S  25%.
The reduced O-ring seal cross-sectional diameter, dcsr = dcs(1 - R/100).
The percent O-ring seal compression with the disk centered is 100 x [dcsr - 1/2(Di - Dg)]/dcsr.
The percent O-ring seal compression with the disk offset is 100 x [dcsr - (Di - Do) - 1/2(Do - Dg)]/dcsr.
A Yes response indicates that helium leakage testing demonstrated that the leakage rate was  1.0 x 10-7 scc/sec, air (i.e., leaktight per ANSI N14.5). In all cases, measured leakage rates were  8.8 x 10-8 scc/sec, helium, for tests with a Yes response.
No helium leak tests were performed at elevated temperatures due to O-ring seal permeation and saturation by helium gas. The ability of the test fixture to establish a rapid, hard vacuum between the O-ring seals was used as the basis for leak test acceptance at elevated temperatures. A Yes response indicates that all tests rapidly developed a hard vacuum.
2.10.2-11
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 This page intentionally left blank.
2.10.2-12
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022
                                              = 4.20&deg; REFERENCE                        = 3.60&deg; DATUM POINT a = 0.153                                  r = 0.125 dU = 0.249 c = 0.561 1          2 d L = 0.251 e = 0.330 x o = 0.599877 y = 0.778404 o
b = 0.493 y = 0.801270 i
                                    = 5.00&deg; f = 0.000 H L = 0.970 h = 0.253 w = 0.563 D g = 73.637517                    g = 0.336162 LOWER                                                                  = 3.90&deg; x i = 0.264494 SEAL FLANGE                                                                                          UPPER SEAL FLANGE D L = 74.185 Figure 2.10.2 Configuration for Minimum ICV O-ring Seal Compression 2.10.2-13
 
HalfPACT Safety Analysis Report                          Rev. 9, August 2022 Figure 2.10.2 Test Fixture for O-ring Seal Performance Testing 2.10.2-14
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 2.10.3 Certification Tests Presented herein are the results of normal conditions of transport (NCT) and hypothetical accident condition (HAC) tests that address the free drop, puncture, and fire test performance requirements of 10 CFR 71 1. This appendix summarizes the information presented in the test reports for the HalfPACT engineering test unit (ETU) 2 and certification test unit (CTU) 3. The test units discussed in this section were configured for testing with two independent containment boundaries. All test results and conclusions with respect to the inner containment vessel (ICV) remain unchanged with the outer containment (now confinement) vessel (OCV) configured as secondary confinement boundary when its optional O-ring seals are utilized. The leaktight capability of the ICV and the structural response and ability of the outer containment (now confinement) assembly (OCA) to protect the ICV are unaffected by the OCV configuration using optional O-ring seals.
2.10.3.1 Introduction The HalfPACT package, when subjected to the sequence of hypothetical accident condition (HAC) tests specified in 10 CFR &sect;71.73, subsequent to the sequence of normal conditions of transport (NCT) tests specified in 10 CFR &sect;71.71, is shown to meet the performance requirements specified in Subpart E of 10 CFR 71. As indicated in the introduction to Chapter 2.0, Structural Evaluation, with the exception of the immersion test, the primary proof of performance for the HAC tests is via the use of full scale testing. In particular, free drop, puncture, and fire testing of both a HalfPACT ETU and CTU confirmed that the ICV and OCV remained leaktight after a worst case HAC sequence. Observations from testing of the two test units also confirm the conservative nature of deformed geometry assumptions used in the criticality assessment provided in Chapter 6.0, Criticality Evaluation.
Since the HalfPACT package is essentially a cut-down version of the TRUPACT-II package, this appendix provides a number of comparative discussions between the HalfPACT and TRUPACT-II certification testing programs. Where appropriate, these comparisons are useful for providing an additional level of confidence in the HalfPACT testing programs by illustrating test results similar to the comprehensive TRUPACT-II certification testing program. As discussed in Appendix 2.10.3.5, Technical Basis for Tests, the selection of HalfPACT test conditions was determined based on the various TRUPACT-II certification tests.
2.10.3.2 Summary As seen in the figures presented in Appendix 2.10.3.7, Test Results, successful testing of the ETU and CTU indicates that the various HalfPACT packaging design features are adequately designed to 1
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 Packaging Technology, Inc. (PacTec), HalfPACT Packaging Engineering Prototype Test Report, PacTec Engineering Document ED-019, Tacoma, Washington.
3 S. A. Porter, et al, Certification Test Report for the HalfPACT Package, TR-001, Packaging Technology, Inc.
(PacTec), Tacoma, Washington.
2.10.3-1
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 withstand the HAC tests specified in 10 CFR &sect;71.73. The most important result of the testing program was the demonstrated ability of the OCV and ICV to remain leaktight 4.
Significant results of free drop testing common to both test units (ETU and CTU) are as follows:
* There was no evidence of buckling of either containment boundary shell. Modest damage to the inner containment vessel shells did occur, an amount somewhat in excess of what was reported in Appendix 2.10.3, Certification Tests, in the TRUPACT-II package SAR 5.
However, it is clear that the damage noted for the HalfPACT package corresponds to the much heavier payload drums interaction with the packaging wall.
* No excessive distortion of the seal flange regions occurred for either the ICV or OCV, although some permanent deformation was noted.
* There was no rupture of the 3/8-inch thick, OCA outer shell.
* Observed permanent deformations of the HalfPACT packaging were less than those assumed for the criticality evaluation.
Significant results of puncture drop testing common to both test units (ETU and CTU) are as follows:
* Besides the obvious permanent damage to the OCA outer shell at the location of the various puncture bar impacts, there was evidence of some permanent deformation of the OCV shell.
The most significant damage occurred at the OCV vent port fitting during testing of the CTU.
The cumulative effects of the NCT and HAC free drops, and the subsequent puncture drop caused successively greater permanent deformation to the region adjacent to the vent port fitting. A crack was noted in the inner weld of the CTUs OCV vent port fitting, but not in the outer weld of the OCV vent port fitting. Subsequent helium leakage rate testing determined that OCV containment integrity was maintained. Although essentially identical in configuration, the ETU did not have a similarly cracked weld. See Appendix 2.10.3.7.2.8, CTU Post-Test Disassembly, for additional discussion regarding this result.
* Penetration of the OCA outer shell occurred below the 3/8-to-1/4-inch thick, OCA outer shell weld during testing of the ETU. The same test, repeated for certification testing, did not reproduce the hole. This result was due to lengthening the 3/8-inch thick, OCA outer shell from 12 to 18 inches, correspondingly changing the impact angle sufficiently to prevent penetration through the adjacent 1/4-inch thick shell.
* There was no rupture of the 3/8-inch thick, OCA outer shell. However, for both test units (ETU and CTU) a linear tear occurred along the weld at the 3/8-to-1/4-inch shell transition in the OCA body outer shell.
Significant results of fire testing common to both test units (ETU and CTU) are as follows:
* The fire tests met or exceeded the minimum flame temperature of 1,475 &#xba;F for 30 minutes as required by 10 CFR &sect;71.73(c)(4).
4 Leaktight is a leakage rate not exceeding 1 x 10-7 standard cubic centimeters per second (scc/sec), air, as defined in ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
5 U.S. Department of Energy (DOE), Safety Analysis Report for the TRUPACT-II Shipping Package, USNRC Docket No. 71-9218, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
2.10.3-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
* Gases formed by thermal degradation of the polyurethane foam were safely vented out the OCA fire vents located in the OCA lid and body.
* The polyurethane foam self-extinguished shortly after the end of the fire.
* The average residual thickness of unburned polyurethane foam in the OCA side wall was approximately five inches in regions undamaged by free drop tests, and approximately three inches in regions damaged by free drop tests. In regions of multiple free drop and puncture drop tests (e.g., at the OCV vent port), only charred foam and ceramic fiber paper remained.
* None of the containment seals sustained extensive degradation due to excessive temperature.
2.10.3.3 Test Facilities Drop testing of the HalfPACT package prototype test unit was performed at Sandia National Laboratories Coyote Canyon Aerial Cable Facility in Albuquerque, New Mexico. The drop test facility utilizes free fall and, if needed, rocket power to attain closely controlled impact velocities as defined by a particular testing program. The drop test facility consists of a 5,000-foot long wire cable suspended across a mountain canyon. The cable can support proportionally heavier package weights at lower elevations, with a package weight in excess of 50,000 pounds for the regulatory defined, hypothetical accident condition 30-foot free drop test. The unyielding target consists of a highly reinforced, armor steel plated concrete block as illustrated in Figure 2.10.3-1. The target is designed to accommodate test packages weighing up to 100 tons.
In accordance with the requirements of 10 CFR &sect;71.73(c)(3), the puncture bar was fabricated from solid, six-inch diameter mild steel, approximately 36 inches long. The puncture bar was welded perpendicularly to a 11/2-inch thick, mild steel plate having an outside diameter of approximately 24 inches. The top edge of the puncture bar was finished to a 1/4-inch radius.
When utilized, the puncture bar was securely welded (mounted) to the impact surface.
Fire testing of the HalfPACT package prototype test unit was performed at Sandia National Laboratories Lurance Canyon Burn Site in Albuquerque, New Mexico. The open pool fire facility can be adjusted to a maximum size of 30 by 60 feet for performing free-burning fires for a duration of 2 hours, maximum. Packages weighing up to 149 tons can be supported at heights up to a few meters above the pool surface. During fire testing, thermocouples and calorimeters that are strategically placed measure and record fire temperatures and heat flux, respectively.
The pool is enclosed by a 20-foot high wind screen deployed in a nominal 50-foot radius from the pool center. The wind screen is constructed of chain link fencing fitted with aluminum slats resulting in a screen porosity of 50%. The wind screen demonstrates a 3-to-1 reduction in wind velocity in high wind conditions, and a 2-to-1 reduction in low wind conditions.
2.10.3.4 Test Unit Description The HalfPACT package is essentially a 30-inch shorter version of the TRUPACT-II package, being identical in almost all respects, the few exceptions noted in later discussions. Both the HalfPACT and TRUPACT-II packages are designed to transport payloads of contact-handled transuranic (CH-TRU) waste. The HalfPACT package is designed to carry nine different payload configurations: 1) seven 55-gallon drums, 2) one standard waste box (SWB), 3) four 85-gallon drums, 4) three 100-gallon drums, 5) three SC-30G1 shielded containers, 6) two SC-30G2 shielded containers, 7) one SC-30G3 shielded container, 8) two SC-55G1 shielded containers, or 9) one SC-55G2 shielded container for its payload. The HalfPACT package height 2.10.3-3
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 is based on the need to carry oversized 85-gallon drums used as overpacks for 55-gallon drums.
Drums may weigh 1,000 pounds each, for a maximum weight of 7,000 pounds for seven 55-gallon drums, 4,000 pounds for four 85-gallon drums, and 3,000 pounds for three 100-gallon drums. The maximum SWB weight is 4,000 pounds. The maximum weight of three SC-30G1s is 6,780 pounds, 6,320 pounds for two SC-30G2s, 6,300 pounds for one SC-30G3, 6,820 pounds for two SC-55G1s, and 6,500 pounds for one SC-55G2.
For purposes of comparison, the primary design differences between the HalfPACT package and TRUPACT-II package are summarized as follows (see Figure 2.10.3-2 and Figure 2.10.3-3 for the differences between the packaging design and 55-gallon drum payload configuration for the TRUPACT-II and HalfPACT packages, respectively):
* maximum package weight: 18,100 pounds for HalfPACT; 19,250 pounds for TRUPACT-II,
* maximum payload assembly weight (including pallet, spacer, guide tubes, and slipsheets):
7,600 pounds for HalfPACT; 7,265 pounds for TRUPACT-II,
* payload assembly configurations (comparing current TRUPACT-II package certification):
55-gallon drums: seven for HalfPACT; fourteen for TRUPACT-II (includes pipe overpacks),
SWBs: one for HalfPACT; two for TRUPACT-II, 85-gallon drums: four for HalfPACT; eight for TRUPACT-II, 100-gallon drums: three for the HalfPACT; six for the TRUPACT-II, ten drum overpack (TDOP): none for HalfPACT; one for TRUPACT-II, SC-30G1s: three for HalfPACT with radial and axial dunnage; none for TRUPACT-II, SC-30G2s: two for HalfPACT with radial and axial dunnage; none for TRUPACT-II, SC-30G3: one for HalfPACT with upper and lower lateral dunnage including end cap spacers; none for TRUPACT-II, SC-55G1s: two for HalfPACT with radial dunnage; none for TRUPACT-II, SC-55G2: one for HalfPACT with upper and lower lateral dunnage; none for TRUPACT-II,
* overall height: 911/2 inches for HalfPACT; 1211/2 inches for TRUPACT-II,
* ICV payload cavity length: 44 inches for HalfPACT; 74 inches for TRUPACT-II,
* OCV cylindrical shell stiffening ring: removed for HalfPACT; included for TRUPACT-II,
* OCA body fire vent locations changed between HalfPACT and TRUPACT-II,
* OCA body, 3/8-inch thick outer shell length: 18 inches for HalfPACT; 12 inches for TRUPACT-II,
* Payload spacer: A payload spacer is used to reduce excess axial clearance for HalfPACT payloads consisting of 55-gallon drums, 100-gallon drums, short 85-gallon drums, and SWBs; no payload spacer is used for TRUPACT-II 2.10.3-4
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 The following sections expand on the individual details relating to the ETU and CTU configurations.
Both HalfPACT packaging engineering test units were fabricated from TRUPACT-II packaging training units 6, as discussed below.
2.10.3.4.1 Engineering Test Unit (ETU)
The HalfPACT packaging engineering test unit (ETU) was fabricated from TRUPACT-II unit number 104, a TRUPACT-II packaging training unit. As illustrated in Figure 2.10.3-4, the OCA body for the HalfPACT ETU was created by removing 30 inches from the OCV cylindrical shell above the torispherical head, and 30 inches from the OCA outer shell below the 3/8-to-1/4-inch shell transition from TRUPACT-II unit number 104. All polyurethane foam and ceramic fiber paper below the parting line was removed. New ceramic fiber paper was installed, the shells welded closed, and new polyurethane foam installed. Polyurethane foam compressive strength properties were tested to be consistent with the requirements of Table 8.1-1 in Section 8.1.4.1, Polyurethane Foam. Similarly, as illustrated in Figure 2.10.3-5, the ICV body for the HalfPACT ETU was created by removing 30 inches of the cylindrical region above the torispherical head from TRUPACT-II unit number 104. Both the OCA and ICV lid assemblies remained unchanged.
Tested differences between the HalfPACT ETU and TRUPACT-II CTUs (i.e., components or parameters used during TRUPACT-II certification testing that were not used during HalfPACT certification testing) are summarized as follows:
* Seal flange O-ring seal region tolerances: carefully controlled fabrication procedures to arrive at worst case (minimum) O-ring seal compression and worst case (maximum) axial free play were used for the TRUPACT-II CTUs; the HalfPACT ETU used unmodified, as-built production unit tolerances,
* Loose debris outside the payload drums: additional cement and sand was used outside the payload drums for the TRUPACT-II CTUs, but not for the HalfPACT CTU (both test programs used additional loose sand inside the payload drums),
* Active and passive test instrumentation (e.g., thermocouples, accelerometers, pressure transducers, and/or temperature indicating labels): active and passive test instrumentation was used for the TRUPACT-II CTUs, but no instrumentation was used for the HalfPACT ETU,
* Internal pressure: pressurization of the containment vessels to the maximum normal operating pressure (MNOP) for some of the free drop, puncture drop, and fire tests was performed for the TRUPACT-II CTUs, but not for the HalfPACT ETU,
* Cooling before drop testing: cooling to -20 &#xba;F prior to some of the free drop and puncture drop tests was performed for the TRUPACT-II CTUs, but not for the HalfPACT ETU,
* Pre-heating before the fire test: pre-heating prior to fire testing was performed for the TRUPACT-II CTUs, but not for the HalfPACT ETU, and
* Cooling before leakage rate testing: cooling to -20 &#xba;F prior to post-test, helium leakage rate testing was performed for the TRUPACT-II CTUs, but not for the HalfPACT ETU.
6 Early TRUPACT-II production units have shells of insufficient thickness per TRUPACT-II SAR requirements.
Designated training units, excessive grinding of some welds in localized regions reduced shell thicknesses below the minimum allowed by the TRUPACT-II (and HalfPACT) SAR packaging general arrangement drawings.
2.10.3-5
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 In addition to the tested differences between the HalfPACT ETU and TRUPACT-II CTUs, the difference between the HalfPACT ETU and the HalfPACT packaging design depicted in Appendix 1.3.1, Packaging General Arrangement Drawings, are summarized as follows:
* Minimum shell material thickness: HalfPACT packaging design requires minimum shell material thicknesses per ASTM A480 7; HalfPACT ETU was fabricated from a cut-down TRUPACT-II training unit (number 104) with localized regions not meeting ASTM A480 because of excessive grinding of some welds,
* OCA body, 3/8-inch thick outer shell length: HalfPACT packaging design is 18 inches long; HalfPACT ETU was 12 inches long,
* Painting of OCA exterior surfaces: HalfPACT packaging design allows optional painting; HalfPACT ETU was not painted,
* OCV vent and seal test port thermal plugs: HalfPACT packaging design specifies foam or ceramic fiber paper thermal plugs; HalfPACT ETU used polyurethane foam thermal plugs,
* Optional catalyst assembly recess in ICV aluminum honeycomb spacers: HalfPACT packaging design specifies &#xd8;18 inches x 11/2 inches deep; HalfPACT ETU used recesses
    &#xd8;15 inches x 11/16 inches deep,
* Aluminum honeycomb spacer assembly attachment bracket: HalfPACT packaging design specifies right-angled brackets; HalfPACT ETU used obtuse-angled brackets,
* Locking ring stop tabs: HalfPACT packaging design specifies up to three stop tabs per locking ring; HalfPACT ETU used one stop tab per locking ring,
* OCA exterior welds: HalfPACT packaging design specifies 3/32-inch maximum weld reinforcement for OCA exterior welds; HalfPACT ETU used 3/32-inch maximum weld reinforcement only on new 3/8-to-1/4-inch, outer shell weld, and
* External handling features were added to the exterior surfaces of the HalfPACT ETU to facilitate lifting and handling the package during testing.
7 ASTM A480/A480M, Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip, American Society for Testing and Materials (ASTM), West Conshohocken, PA.
2.10.3-6
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 The following table summarizes a comparison of major component weights for the HalfPACT ETU and TRUPACT-II CTUs:
Packaging                  TRUPACT-II Certification Test Units        HalfPACT Component                  CTU No. 1    CTU No. 2      CTU No. 3        ETU Empty Package
* ICV Assembly                          2,614          2,773          2,570        2,025
* OCA Assembly                          9,450          9,400          9,196        8,100
* Total                                12,064        12,173        11,766        10,125 Payload
* 55-Gallon Drums                        7,000          7,000          7,000        7,350
* Pallet, Slipsheets, etc.                315            269            375          160
* Total                                  7,315          7,269          7,375        7,510 Loaded Package Total                      19,379        19,442        19,141        17,635 2.10.3.4.2 Certification Test Unit (CTU)
Similar to the HalfPACT ETU, the HalfPACT packaging certification test unit (CTU) was fabricated from TRUPACT-II unit number 107, a TRUPACT-II packaging training unit. As illustrated in Figure 2.10.3-6, the OCA body for the HalfPACT CTU was created by removing 30 inches from the OCV cylindrical shell above the torispherical head, and 36 inches from the OCA outer shell below the 3/8-to-1/4-inch shell transition from TRUPACT-II unit number 107.
All polyurethane foam and ceramic fiber paper below the parting line was removed. Six inches of 3/8-inch thick, OCA outer shell was added below the existing 12-inch length to extend the shell length to 18 inches per the HalfPACT packaging design. New ceramic fiber paper was installed, the shells welded closed, and new polyurethane foam installed. Polyurethane foam compressive strength properties were tested to be consistent with the requirements of Table 8.1-1 in Section 8.1.4.1, Polyurethane Foam. Similarly, as illustrated in Figure 2.10.3-7, the ICV body for the HalfPACT CTU was created by removing 30 inches of the cylindrical region above the torispherical head from TRUPACT-II unit number 107. Both the OCA and ICV lid assemblies remained unchanged. All OCA exterior surfaces were painted gray.
Tested differences between the HalfPACT CTU and TRUPACT-II CTUs (i.e., components or parameters used during TRUPACT-II certification testing that were not used during HalfPACT certification testing) are summarized as follows:
* Seal flange O-ring seal region tolerances: carefully controlled fabrication procedures to arrive at worst case (minimum) O-ring seal compression and worst case (maximum) axial free play were used for the TRUPACT-II CTUs; the HalfPACT CTU used unmodified, as-built production unit tolerances,
* Loose debris outside the payload drums: additional cement and sand was used outside the payload drums for the TRUPACT-II CTUs, but not for the HalfPACT CTU (both test programs used additional loose sand inside the payload drums),
2.10.3-7
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
* Active and passive test instrumentation (e.g., thermocouples, accelerometers, pressure transducers, and/or temperature indicating labels): active and passive test instrumentation was used for the TRUPACT-II CTUs, but only temperature indicating labels were used for the HalfPACT CTU,
* Internal pressure: pressurization of the containment vessels to the maximum normal operating pressure (MNOP) for some of the free drop, puncture drop, and fire tests was performed for the TRUPACT-II CTUs, but not for the HalfPACT CTU,
* Cooling before drop testing: cooling to -20 &#xba;F prior to some of the free drop and puncture drop tests was performed for the TRUPACT-II CTUs, but not for the HalfPACT CTU,
* Pre-heating before the fire test: pre-heating prior to fire testing was performed for the TRUPACT-II CTUs, but not for the HalfPACT CTU, and
* Cooling before leakage rate testing: cooling to -20 &#xba;F prior to post-test, helium leakage rate testing was performed for the TRUPACT-II CTUs, but not for the HalfPACT CTU.
In addition to the tested differences between the HalfPACT CTU and TRUPACT-II CTUs, the difference between the HalfPACT CTU and the HalfPACT packaging design depicted in Appendix 1.3.1, Packaging General Arrangement Drawings, are summarized as follows:
* Minimum shell material thickness: HalfPACT packaging design requires minimum shell material thicknesses per ASTM A480; HalfPACT CTU was fabricated from a cut-down TRUPACT-II training unit (number 107) with localized regions not meeting ASTM A480 because of excessive grinding of some welds,
* Optional catalyst assembly recess in ICV aluminum honeycomb spacers: HalfPACT packaging design specifies &#xd8;18 inches x 11/2 inches deep; HalfPACT CTU used recesses
    &#xd8;15 inches x 11/16 inches deep,
* Aluminum honeycomb spacer assembly attachment bracket: HalfPACT packaging design specifies right-angled brackets; HalfPACT CTU used obtuse-angled brackets,
* Locking ring stop tabs: HalfPACT packaging design specifies up to three stop tabs per locking ring; HalfPACT CTU used one stop tab per locking ring,
* OCA exterior welds: HalfPACT packaging design specifies 3/32-inch maximum weld reinforcement for OCA exterior welds; HalfPACT CTU used 3/32-inch maximum weld reinforcement only on new 3/8-to-3/8-inch and 3/8-to-1/4-inch, outer shell welds, and
* Payload Spacer: To accommodate a single layer of 55-gallon drums for the test payload, a 5-inch high wooden payload spacer was utilized,
* External handling features were added to the exterior surfaces of the HalfPACT CTU to facilitate lifting and handling the package during testing.
* The OCV was fabricated to the requirements of the ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB (rather than Subsection NF).
* Some detailed dimensions for the OCV seal flanges, locking ring, and OCV upper main O-ring seal are slightly different from those delineated in Appendix 1.3.1, Packaging General Arrangement Drawings.
2.10.3-8
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022
* Generic polymer may be used for the optional OCV containment (now confinement), test, and OCV vent port plug O-ring seals; all CTUs utilized butyl rubber for these seals.
* Butyl, neoprene, or ethylene propylene elastomers may be used for the ICV inner vent port plug O-ring seal, and the ICV seal test port plug O-ring seal; all CTUs used butyl rubber for these seals.
* Generic polymer may be used for the optional OCV vent port plug and cover handling O-ring seals, the OCV vent port cover O-ring seal, and the OCV seal test port plug O-ring seal; all CTUs used butyl rubber for these seals.
* Generic polymer may be used for the optional OCV guide plates; all CTUs used stainless steel for these plates.
* Aluminum honeycomb spacers may be constructed with one or two top sheet layers of aluminum; all CTUs used one top sheet layer.
The following table summarizes a comparison of major component weights for the HalfPACT ETU and CTU, and TRUPACT-II CTUs:
Packaging                        TRUPACT-II                          HalfPACT Component              CTU No. 1 CTU No. 2 CTU No. 3              ETU          CTU Empty Package
* ICV Assembly                    2,614        2,773        2,570        2,025        2,120
* OCA Assembly                    9,450        9,400        9,196        8,100        7,950
* Total                          12,064      12,173        11,766      10,125        10,070 Payload
* 55-Gallon Drums                7,000        7,000        7,000        7,350        7,410
* Pallet, Payload Spacer, etc.      315          269          375          160          590
* Total                          7,315        7,269        7,375        7,510        8,000 Loaded Package Total              19,379      19,442        19,141      17,635        18,070 2.10.3.5 Technical Basis for Tests The following sections supply the technical basis for the chosen test orientations and sequences for both the HalfPACT ETU and CTU as presented in Section 2.10.3.6, Test Sequence for Selected Free Drop, Puncture Drop, and Fire Tests.
2.10.3-9
 
HalfPACT Safety Analysis Report                                                              Rev. 9, August 2022 2.10.3.5.1 Initial Test Conditions 2.10.3.5.1.1 Internal Pressure Internal pressure could affect the certification test results in two ways. First, it imparts primary stress to the containment vessels, and second, it could affect the leaktight condition of the seals in a HAC fire. In the first case, containment vessel stress due to internal pressure is pr/t = 7,288 psi, where p, the internal design pressure, is 50 psi, the ICV mean radius, r, is 36.44 inches, and the thickness, t, is 0.25 inches. Per Regulatory Guide 7.6, this stress is compared to the design stress intensity, Sm =
20,000 psi at NCT temperatures. The result is that pressure-related membrane stress that is only 36%
of the allowable stress. Pressure would normally be present only in the ICV, and due to the presence of the OCA, the polyurethane foam, and the OCV, the relative deformation of the ICV due to any free drop or puncture event is insignificant. Further, during TRUPACT-II testing, no pressure spikes as a result of impact were recorded. Thus, the addition of pressure membrane stress would be insignificant to the outcome of HalfPACT free drop and puncture drop testing.
In the second case, the pressure sealing capacity of the containment seals is significantly greater than the maximum normal operating pressure (MNOP) of 50 psig. For the HAC fire test, O-ring seal compression is expected to increase as a result of differential expansion between the seal and the surrounding metal, thus increasing the pressure capacity of the seal. Certification testing of the TRUPACT-II demonstrated that no pressure was lost for any of the fire tests. Therefore, as long as temperatures in the O-ring seal regions are similar to the temperatures measured during TRUPACT-II fire testing, pressurizing either the ICV or OCV is considered unnecessary for HalfPACT certification fire testing.
2.10.3.5.1.2 Temperature Ambient temperature will be used at the time of HalfPACT certification testing. Results might differ if the two extremes (NCT maximum temperature, or minimum, -20 &#xba;F, temperature) were employed. However, it can be shown that these differences are not significant as follows.
As discussed in Section 2.7, Hypothetical Accident Conditions, polyurethane foam compressive strength at an NCT temperature of 160 &#xba;F is approximately 75% of the compressive strength at 75 &#xba;F, and at -20 &#xba;F is approximately 140% of the crush strength at 75 &#xba;F. In contrast, the minimum strength of the Type 304 stainless steel varies to a much lesser extent, decreasing from 35,000 psi at -20 &#xba;F 8 to 30,000 psi at 100 &#xba;F, and to 27,000 psi at 160 &#xba;F. Thus, for drop orientations where stresses in structural steel members are of concern, the worst case temperature is -20 &#xba;F since this is the temperature where the ratio of impact induced acceleration load to steel strength is the greatest. For drop orientations where deformations are of concern, elevated temperatures would result in a worst-case condition.
Deformations will be greater if the polyurethane foam is at NCT warm temperatures during free and puncture drops. The greater the deformation, the less residual foam thickness to protect the O-ring seals from thermal degradation in the subsequent fire. The elastomer seal material short-term temperature limit is 400 &#xba;F per Appendix 2.10.2, Elastomer O-ring Seal Performance Tests.
8 For the purposes of this discussion, yield strength at -20 &#xba;F is extrapolated from data in Table 2.3-1 using a curve shape for Type 304 stainless steel in the -80 &#xba;F to 800 &#xba;F range in Engineering Properties of Steel, Philip D. Harvey, Editor, American Society for Metals, 1982.
2.10.3-10
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 Considering a maximum O-ring seal region temperature of 260 &#xba;F for TRUPACT-II fire testing and the relatively large amount of unburned foam following fire testing (~5 inches, average), the margin against O-ring seal failure is relatively large. In view of this, a reasonable limit for the average maximum O-ring seal region temperature for HalfPACT fire testing is 300 &#xba;F. In this case, the margin will be virtually as great as for the TRUPACT-II, and drop testing at warm temperatures is considered unnecessary.
Impact forces will be greater if the polyurethane foam is at NCT cold temperatures (-20 &#xba;F) during free and puncture drops. However, the bounding free drop where impact severity is a factor is a side slapdown. As discussed in Section 2.10.3.5.2.4, Closure (Lid) Separation, the results indicate that all HalfPACT slapdown drops are enveloped by TRUPACT-II slapdown drops. Therefore, reduction of the foam temperature would still not create a governing impact severity condition, and drop testing at cold temperatures is considered unnecessary.
2.10.3.5.2 Free Drop Tests The HalfPACT package is qualified primarily by full scale testing, with the acceptance criterion being the ability to demonstrate leaktight containment for both the OCV and ICV.
Per 10 CFR &sect;71.73(c)(1), the package is required to strike an essentially unyielding surface in a position for which maximum damage is expected. Therefore, for determining the drop orientations that satisfy the regulatory maximum damage requirement, attention is focused predominantly on the issue of containment. Loss of containment could potentially occur one of two ways: 1) directly, as a result of free drop impact damage, or 2) indirectly, as a result of normal conditions of transport (NCT) or hypothetical accident condition (HAC) impact damage that could lead to degradation of sealing capability in the subsequent puncture and/or fire events.
Direct damage would take the form of one of the following:
: 1. Rupture of a containment vessel,
: 2. Buckling of a containment vessel,
: 3. Excessive deformation in the main O-ring sealing region resulting in the loss of a leaktight seal, and/or
: 4. Separation of one of the containment vessel lids from its corresponding body.
Indirect damage would require significant impact damage to the surrounding polyurethane foam leading to thermal degradation of the seal material. A significant reduction in polyurethane foam thickness or a gross exposure of the foam through splits or punctures in the OCA outer shell would have to occur near the main O-ring seal or vent port seal region. In a free drop event, such damage could occur as follows:
: 5. Deformation of the polyurethane foam due to impact could result in an inadequate remaining thickness to prevent seal thermal degradation in the fire event, and/or
: 6. Deformation of the OCA outer shell could lead to a fissure in the shell material or in a weld, or a puncture through the shell material, thereby exposing foam.
These six issues will now be discussed in detail in the following sections.
2.10.3-11
 
HalfPACT Safety Analysis Report                                                            Rev. 9, August 2022 2.10.3.5.2.1 Containment Vessel Rupture Rupture of a containment vessel as a result of the HAC free drop is not credible for the HalfPACT package. In comparison, the TRUPACT-II package was certified utilizing three different certification test packages that were subjected to a large number of 3-foot NCT free drops, and 30-foot HAC free drops. Post-test examination of the TRUPACT-II CTUs revealed no indication of impending rupture of either the OCV or ICV, either as a result of impact forces with the ground or as a result of interaction with the maximum-weight payload. The HalfPACT package is both 25% shorter and 6% lighter than the TRUPACT-II package. Otherwise, construction, including shell thicknesses and foam strength, is essentially identical 9. Therefore, behavior of the HalfPACT package with regards to containment vessel rupture will be the same, and rupture will not occur as demonstrated during TRUPACT-II package certification testing.
2.10.3.5.2.2 Containment Vessel Buckling Buckling of a containment vessel as a result of the HAC free drop is also not of concern. As mentioned above, the similar TRUPACT-II package was tested extensively as a part of its certification process. TRUPACT-II testing included a flat bottom impact with cold, -20 &#xba;F, polyurethane foam to impose maximum axial impact forces. In these drops, no indication of containment vessel buckling was observed. The HalfPACT package is, however, 6% less gross weight than the TRUPACT-II package, and the OCV body shell ring stiffener is not included. It will now be shown that these differences are insignificant relative to buckling.
Impact acceleration is a function of the crush force and of the package weight, as follows:
F g=
W where g is the impact level in units of gs, F is the crush force, and W is the package weight. If weight is reduced and the force is conservatively assumed to remain constant 10, it is possible to determine an impact level for a lighter package based on results for a heavier one. From the TRUPACT-II SAR, the impact for the governing, bottom-down drop, with -20 &#xba;F foam, was 385g. Using the above relation, the maximum bottom-down impact would therefore be 385g x WT/ WH = 409g, where the TRUPACT-II package weight, WT = 19,250 pounds, and the HalfPACT package weight, WH = 18,100 pounds.
The compressive stress in the ICV shell is a function of both the impact load and the weight of the shell. The weight conservatively includes ICV assembly and upper aluminum honeycomb spacer assembly, but does not include the weight of the lower ICV torispherical head. Therefore, the total weight on the ICV shell is approximately 1,722 pounds, resulting in a corresponding compressive stress in the ICV shell of:
9 With the exception of the overall reduction in packaging height of 30 inches, the HalfPACT and TRUPACT-II packages differ in only a few minor aspects. The two most notable aspects are removal of the OCV stiffener ring, and beneficially lengthening of the 3/8 inch thick portion of the OCA outer shell, just below the OCA closure joint.
10 This simplifying assumption is based on an equivalent impact footprint for the HalfPACT and TRUPACT-II packages. Due to lower deformation, strain hardening, and geometric considerations, the impact force is somewhat less for the lighter weight HalfPACT package, but is never greater than the TRUPACT-II package.
2.10.3-12
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 P Wg          (1,722)(409 g )
                              =      =      =                      = 12,305 psi A dt (72.875)(0.25) where the mean diameter of the ICV shell, d = 72.875 inches, and the shell thickness, t = 0.25 inches. Note that the stress calculated above is less than the equivalent value of 14,192 psi determined in the TRUPACT-II SAR. This result is because, even though the HalfPACT impact is 6% greater than the TRUPACT-II impact, the weight used is 18% less due to a 30-inch shorter OCV body shell length for the HalfPACT package. Therefore, since the governing stress in the HalfPACT ICV shells under worst case cold end drop conditions is lower than for the TRUPACT-II, buckling of the HalfPACT is not of concern.
Similarly, buckling of the OCV is not of concern. As for the TRUPACT-II, the HalfPACT OCV is surrounded by supporting polyurethane foam. And, even though the OCV body ring stiffener is not used on the HalfPACT package as for the TRUPACT-II package, the longest unsupported length for each package is almost identical. Therefore, buckling of the HalfPACT package OCV shell will not occur, and a cold, bottom end drop is not a bounding test.
2.10.3.5.2.3 Excessive Deformation in the Main O-ring Sealing Region Excessive deformation in the main O-ring sealing region would be most likely to occur in a drop orientation where the seal region is in the impact zone. For the HalfPACT package, where the seal flanges are located approximately halfway along its length, the seal region can experience local impact only in a horizontal side drop. In addition, payload interaction forces between the payload and the ICV are maximized in a side drop since the entire payload inertia force must be carried through the ICV sidewall, and proportionally through the ICV seal region. Excessive deformation of the sealing surfaces could relieve O-ring seal compression and potentially affect leaktight containment. Therefore, a side drop orientation should be tested.
2.10.3.5.2.4 Closure (Lid) Separation A lid could become partially separated from the body if tensile or moment forces on the lid are high enough to cause permanent deformation of the seal flanges or locking ring. Due to the shape of the HalfPACT package, direct tensile forces separating the lid from the body are not possible for primary impact in a free drop event. For the same reason, moment forces also do not occur at the joint in a horizontal side drop. However, in a near-horizontal orientation, it is possible for moment forces to occur at the lid joint for secondary impact in a slapdown event.
Since lid and closure design for both the TRUPACT-II and HalfPACT packages are identical, and since the TRUPACT-II package was subjected to two different slapdown drop orientations, the lid closure has previously been successfully subjected to such moment forces. It remains to be shown, however, that the moments experienced during TRUPACT-II package certification testing envelop or bound those of the HalfPACT package. Bounding analyses can be done using the methods outlined in NUREG/CR-3966 11.
Section 2.2 of NUREG/CR-3966 presents a method for evaluating the axial force, shear force, and bending moment in a package as it undergoes impact, including primary and secondary 11 T. A. Nelson, R. C. Chun, Methods for Impact Analysis of Shipping Containers, NUREG/CR-3966, UCID-20639, U.S. Nuclear Regulatory Commission, November 1987.
2.10.3-13
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 (slapdown) impacts. The analysis consists of two parts. First, the portion of the total energy that is absorbed by a given impact (say, primary) is determined. Realizing that this energy is equivalent to the area beneath the force-deflection curve for a given drop height and orientation, the maximum force acting on that end of the cask is established. Then, using this force and a quasi-static analysis, the axial, shear, and moment forces in the cask can be determined. These internal force distributions are plotted as a function of force, F, and cask length, L, in Figure 2.7 (primary impact) and Figure 2.10 (secondary impact) of NUREG/CR-3966. Using these relationships, the response of the TRUPACT-II and HalfPACT packages can be compared.
The relevant parameters of each package are defined as follows. The impact limiter in both cases is fully enveloping, and, for simplicity, the nose (primary) and tail (secondary) impact limiters are defined as meeting at the geometric center of the package. The length of the equivalent cask is defined in each case as equal to the length of the payload cavity, plus 2/3 of the length of each aluminum honeycomb spacer. The resulting length is 90.34 inches for the TRUPACT-II package model, and 60.34 inches for the HalfPACT package model, since the length of the HalfPACT package is 30 inches less than the TRUPACT-II package. In both cases, the package inside diameter is 73 inches at the lower end is the OCV body, and is 76 inches at the upper end is the OCV lid. In both cases, the outer diameter of the impact limiters is the outside diameter of the OCA outer shell, or 94 inches. The weight (including the maximum weight payload) is 19,250 pounds for the TRUPACT-II package and 18,100 pounds for the HalfPACT package. The corresponding rotational mass moment of inertia is 89,487 in-lb-s2 for the TRUPACT-II package and 59,239 in-lb-s2 for the HalfPACT package.
The method described requires the use of impact limiter, force-deflection curves. These are generated by means of the Packaging Technology computer code, CASKDROP 12. Once impact limiter geometry is defined, this program calculates crush force as a function of impact limiter deformation using simple geometry and a foam stress-strain curve. A foam stress-strain curve is used that, for a horizontal side drop of 30 feet, gives the same deformation distance as for the TRUPACT-II certification tests (3 inches for CTU No. 1, Test No. 2). An illustration of each package, along with the corresponding CASKDROP representation, is given in Figure 2.10.3-8.
The forces and moments in the cask are evaluated at a distance x from the lid end, which is equivalent to the location of the axial center of the OCV locking ring, or 20.0 inches in each case. A drop height of 30 feet is used.
Given the package mass, rotational moment of inertia about its center of gravity, cask length, and angle of primary impact, the energy absorbed by the primary impact limiter can be found from Equation 2.2-10 of NUREG/CR-3966. From the force-deflection curve of the primary impact limiter at the same orientation the maximum force reached in the crush event can be found.
Then, given the crush force and the distance, x, the resulting axial force, shear force, and bending moment in the cask at the location of interest (the OCV locking ring) can be found from Equations 2.2-1 through 2.2-3 of NUREG/CR-3966. Similarly, the forces and moments at the OCV locking ring due to the secondary impact can be found as follows: Equation 2.2-11 for the energy absorbed by the secondary impact limiter, the force-deflection curve for the secondary impact from CASKDROP (secondary impact is assumed to be horizontal), and Equations 2.2-12 12 S. A. Porter, CASKDROP v2.31 - A Computer Program to Determine Cask Force-Deflection Response to a Free Drop, Packaging Technology, Inc. (PacTec), Tacoma, Washington.
2.10.3-14
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 and 2.2-13 for axial, shear, and moment forces. Note that the force-deflection curves are identical for TRUPACT-II and HalfPACT packages.
Since the lid force-deflection curves differ slightly from the body end force-deflection curves (because the cask diameter is 76 inches at the lid and 73 inches at the body end), two complete sets of results are obtained for each package: one set is lid primary, body secondary, and the other is body primary, and lid secondary. Primary impact angles of 5&#xba;, 10&#xba;, and 15&#xba; are investigated, plus two special cases for the TRUPACT-II based on orientations used during actual testing. The results are summarized in Table 2.10.3-1. Also included in the table are lid primary impacts with the packages center of gravity over the impacted corner. Results are compared primarily based on shear and moment forces.
Note that for the TRUPACT-II, the forces due to the secondary impact are always greater than for the primary impact, whereas for the HalfPACT, this is not always the case. This outcome is a function of the different relationships between the cask length, L, and the locking ring location,
: x. Also, note that the worst overall case is for the TRUPACT-II, primary impact angle of 5&#xba;,
body primary. The worst case actually tested (body primary, impact angle 18&#xba;) is within 2% of this maximum value. Importantly, note that none of the HalfPACT results approach these values. The worst case HalfPACT result (lid primary, impact angle 5&#xba;) has a shear load and moment of 7,431 pounds and 1.760(10)7 in-lb, respectively, which is much less than the actual TRUPACT-II certification test values (body primary, impact angle 18&#xba;; CTU No. 2, Test No. 1) of 477,148 pounds and 2.212(10)7 in-lb, respectively. Therefore, the worst case HalfPACT slapdown lid closure forces and moments are bounded by TRUPACT-II certification testing.
2.10.3.5.2.5 Insufficient Residual Foam Thickness for Fire Protection The package deformations which result from free drop impacts will reduce the thickness of polyurethane foam in the region of damage, with a consequent reduction in the ability of the foam layer to insulate the seal regions during the fire event. If deformation is excessive, thermal degradation of the elastomeric O-rings could occur and the leaktightness of the ICV and/or OCV could be affected. The worst case reduction in thermal resistance would occur where free drop and puncture damage are combined at the most vulnerable location on the package.
Of the two vessels, the OCV is most vulnerable, since as the outermost vessel it is nearest the fire. There are two penetrations in the OCV: the main closure (lid) and the vent port. Since the main seal flanges have considerably more thermal mass than the vent port fitting, the vent port fitting is the more critical location. Puncture damage is discussed in the next section, but for the purposes of choosing the most damaging free drop orientation relative to thermal degradation of the seals in the subsequent fire, the horizontal side drop, with the OCV vent port located in the center of the impact, is the worst case. The only other orientation in which greater local deformation might occur is at the lid knuckle, due to a center of gravity over corner drop.
However, this location is relatively far from the sealing regions, and is therefore not as vulnerable in the subsequent fire.
2.10.3.5.2.6 OCA Outer Shell Fracture/Tearing Deformation of the OCA shell, if it caused a fracture or tear in the base material or weld, would expose foam directly to the fire conditions. The polyurethane foam used in the HalfPACT is intumescent, such that relatively small holes or tears are filled with an expansive char under fire conditions. Depending on size, fractures or tears are therefore self-healing and do not result in 2.10.3-15
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 significantly higher temperatures on the inside surface of the foam (i.e., in sealing regions).
However, extensive testing of the TRUPACT-II certification packages exhibited no tendency to develop such openings, however, as a result of NCT or HAC free drops, regardless of orientation. This behavior is due to the highly ductile nature of Type 304 stainless steel and the use of full penetration welds for OCA shell construction. Therefore, substantial foam exposure as a result of a free drop is not credible.
2.10.3.5.3 Puncture Drop Tests 10 CFR &sect;71.73(c)(3) requires a free drop of the specimen through a distance of 40 inches onto a puncture bar in a position for which maximum damage is expected. As in Section 2.10.3.5.2, Free Drop Tests, the maximum damage criterion is evaluated primarily in terms of loss of containment. Loss of containment could occur directly, due to actual puncture bar impact on the package components, or indirectly, by inducing damage which might lead to degradation of sealing capability in the subsequent fire event.
Direct damage would take the form of one of the following:
: 1. Rupture of one of the containment vessels (ICV or OCV),
: 2. Separation of the OCV lid from its body,
: 3. Loss of leaktight capability of the OCV seals due to excessive local deformation of the sealing region, and/or
: 4. Loss of sealing capability of an ICV or OCV vent port plug.
For seal degradation to occur in a subsequent fire, significant exposure or loss of polyurethane foam would have to occur in the vicinity of the O-ring seals as a result of puncture damage.
Such damage might occur as follows:
: 5. Deformation of the OCA shell due to puncture bar impact, when added to the deformation arising from the free drop, could result in inadequate remaining thickness to prevent local seal thermal degradation in the fire event, and/or
: 6. Puncture bar impact could result in a fissure in the OCA material or weld, exposing significant foam to the fire event.
These issues will now be discussed in detail in the following sections.
2.10.3.5.3.1 Containment Vessel Rupture Rupture of one of the containment vessels is not a likely failure mode. The TRUPACT-II certification test packages were subjected to a number of puncture drops where the bar axis was aligned with the package center of gravity. The worst damage to the containment vessels was a relatively insignificant denting of the OCV in a region well removed from the seal regions. Due to its similar geometry but lighter weight, the HalfPACT package is slightly less susceptible to puncture bar damage than the TRUPACT-II. Therefore, direct rupture of the containment vessels will not occur for the HalfPACT.
2.10.3.5.3.2 Closure (Lid) Separation Separation of the OCV lid due to puncture bar impact is extremely unlikely. To rip the OCV lid off of the OCV body would require failure of the OCV locking ring, which cannot occur due to 2.10.3-16
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 puncture bar impact. The potential energy available in a 40-inch puncture drop is equal to 40/(12 x 30) = 11.1% of the energy available in the 30-foot free drop. As shown in Section 2.10.3.5.2.4, Closure (Lid) Separation, the greatest lid separation loads that are to be applied in the near-horizontal slapdown drop are not able to separate the OCV lid. Therefore, separation of the lid in a 40-inch puncture drop is not credible. To make such an event even more unlikely, the orientation of the puncture bar that is necessary to apply a separating load on the lid joint is such that it diverges from the package center of gravity, thus reducing the energy available to apply to the joint. Therefore, separation of the OCV lid due to puncture bar impact will not occur for the HalfPACT package. Local puncture bar damage is discussed below.
2.10.3.5.3.3 Loss of Lid Sealing Integrity Loss of leaktight capability of the OCV seals due to local puncture bar deformation is not likely.
This behavior is because, due to the presence of increased thickness (3/8 inch) OCA shells in the sealing region, of Z-flanges, and of polyurethane foam, virtually all of the puncture drop energy is absorbed before significant deformation of the OCV sealing area has taken place. This behavior was demonstrated during TRUPACT-II certification testing, by means of drops where the puncture bar axis was aligned with the OCV sealing area and the package center of gravity (TRUPACT-II CTU No. 2, Test No. 8, and CTU No. 3, Test No. 8). Therefore, loss of leaktight capability of the OCV seals due to local puncture bar deformation will not occur for the HalfPACT package. However, for reasons discussed below, a puncture bar impact is planned which will be located very near the OCV sealing area, with the axis passing through the package center of gravity, and which will simultaneously demonstrate the ability of the HalfPACT package to sustain such damage without loss of its leaktight capability.
2.10.3.5.3.4 Loss of Vent Port Sealing Integrity Loss of sealing capability of an ICV or OCV vent port plug is unlikely for the same reasons cited in Section 2.10.3.5.3.3, Loss of Lid Sealing Integrity. Since deformation of the OCV in any puncture drop is minimal, only the OCV vent port plug could possibly be affected by a puncture impact. Due to the small size of the plug, and to protection by surrounding structure, deformations do not reach the level at which the seal could be affected. This behavior was well demonstrated during TRUPACT-II certification testing (CTU No. 1, Test No. 5; CTU No. 2, Test No. 7; and CTU No. 3, Test No. 7). Again, for reasons discussed below, a puncture bar impact is planned to occur directly over the OCV vent port, in alignment with the package center of gravity, and in combination with compounded NCT and HAC side drop damage. This test will amply demonstrate the ability of the HalfPACT package to sustain such damage without loss of OCV vent port leaktight capability.
2.10.3.5.3.5 Insufficient Residual Foam Thickness for Fire Protection Deformation of the OCA shell due to puncture bar impact, when added to the deformation arising from the free drop, could result in inadequate remaining thickness to prevent local seal thermal degradation in the fire event. Therefore, a puncture drop is planned in which damage from free drop and puncture are combined, with the puncture located directly over the OCV vent port, as discussed above in Section 2.10.3.5.2, Free Drop Tests, and Section 2.10.3.5.3.4, Loss of Vent Port Sealing Integrity.
2.10.3-17
 
HalfPACT Safety Analysis Report                                                                    Rev. 9, August 2022 2.10.3.5.3.6 OCA Outer Shell Fracture/Tearing Puncture bar impact could result in a fracture or tear of the OCA outer shell base material or weld, exposing significant foam to the fire event. The polyurethane foam used in the HalfPACT is intumescent, such that holes (such as puncture bar holes) or relatively small tears are filled with an expansive char under fire conditions. Depending on size, holes or tears are therefore self-healing and do not result in significantly higher temperatures on the inside surface of the foam, i.e., near sealing regions.
The likelihood of creating significant damage is increased by use of an oblique angle between the puncture bar and the package surface. It is also increased by the presence of a transition in package outer shell thickness. In the case of the HalfPACT package, the OCA outer shell experiences a transition in thickness from 1/4 inch to 3/8 inch, located approximately 19 inches below the lid-to-body interface joint. The 3/8-inch thickness is located above the transition. The angle of the package to the horizontal is approximately 20&#xba;. A puncture drop at this location is the most likely to produce relevant damage, since:
* a transition in shell thickness, including a full penetration weld, is located there,
* the puncture bar axis, aligned with the package center of gravity, has an oblique orientation to the package surface, increasing its likelihood to bite and rip the shell, and
* the location is close to the sealing region, relative to thermal degradation in the fire event.
Further down the package, even though the puncture bar orientation would be more oblique, there is no comparable shell thickness transition, and additionally, would be farther away from the vulnerable seal region. Farther up the package (closer to the lid-to-body joint), even though the puncture damage would be closer to the seals, the outer shell thickness has no transition, is thicker (3/8 inch), and the puncture bar orientation is nearer to perpendicular to the package, thus minimizing its potential to bite and rip the shell. As described in the next section, in order to fully explore the potential of this puncture orientation, two separate puncture events are planned.
The circumferential location for the impact is chosen such that the worst-case damage at the OCV vent port and the worst case damage from one of the two punctures discussed here can both be simultaneously placed in the hottest part of the fire in the subsequent fire test. The hottest part of the fire is located approximately 11/2 meters above the fuel surface 13. Since the lowest part of the package is located one meter above the fuel surface (per 10 CFR &sect;71.73(c)(4)), the damage must be 1/2 meter, or approximately 20 inches, above the lowest part of the package. If two damage locations are to be thus placed, they must be separated by approximately 110&#xba;, based on the HalfPACT package outside diameter. Thus, since either of the two puncture events discussed here most likely create the maximum damage in conjunction with the OCV vent port side drop/puncture drop damage, one is placed 110&#xba; counter-clockwise and the other 110&#xba; clockwise from the OCV vent port. In the fire, the OCV vent port damage, plus the worst one of the other two puncture damage sites, will therefore be placed in the hottest part of the fire.
13 M. E. Schneider and L. A. Kent, Measurements of Gas Velocities and Temperatures in a Large Open Pool Fire, Sandia National Laboratories (reprinted from Heat and Mass Transfer in Fire, A. K. Kulkarni and Y. Jaluria, Editors, HTD-Vol. 73 (Book No. H00392), American Society of Mechanical Engineers). Figure 3 shows that maximum temperatures occur at an elevation approximately 2.3 meters above the pool floor. The pool was initially filled with water and fuel to a level of 0.814 meters. The maximum temperatures therefore occur approximately 11/2 meters above the level of the fuel, i.e., 1/2 meter above the lowest part of the package when set one meter above the fuel source per the requirements of 10 CFR &sect;71.73(c)(4).
2.10.3-18
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 2.10.3.5.4 Fire Test At the conclusion of free drop and puncture drop testing, the HalfPACT test units will be subjected to a fully engulfing pool fire test in accordance with 10 CFR &sect;71.73(c)(4). The package will be oriented horizontally in the flames and minimally supported to least impede the heat flow into the package. The combined damage due to the free and puncture drops on the OCV vent port region will be located in the hottest portion of the fire, i.e., 11/2 meters above the fuel surface, i.e., 1/2 meter above the lowest part of the package. The damage due to other puncture drops will be evaluated, and the most damaging puncture test oriented similarly at 1/2 meter above the lowest part of the package.
Justification is provided in Section 2.10.3.5.1, Initial Test Conditions, for using ambient pressure and temperature in the HalfPACT test units. Temperature indicting labels will be used with the HalfPACT CTU to determine the maximum temperature in the O-ring seal region during the HAC fire test. Determination of the maximum O-ring seal region temperature must account for ambient temperature conditions starting below the HAC fire test initial temperatures predicted in Section 3.5.3, Package Temperatures. This will be accomplished by adding the temperature differential between the actual ambient temperature and the analytically predicted O-ring seal region starting temperature to the average measured O-ring seal region temperature. Although conservative, the result will be directly comparable to measured TRUPACT-II certification fire test temperatures in the O-ring seal regions. As discussed in Section 2.10.3.5.1, Initial Test Conditions, a maximum O-ring seal region temperature of 300 &#xba;F for HalfPACT fire testing shall be considered acceptable.
2.10.3.6 Test Sequence for Selected Free Drop, Puncture Drop, and Fire Tests The following sections establish the selected free drop, puncture drop, and fire test sequence for both the HalfPACT engineering test unit (ETU) and HalfPACT certification test unit (CTU) based on the discussions provided in Section 2.10.3.5, Technical Basis for Tests. The test sequences are summarized in Table 2.10.3-2 and Table 2.10.3-3, and illustrated in Figure 2.10.3-9 and Figure 2.10.3-10 for the ETU and CTU, respectively.
2.10.3.6.1 Engineering Test Unit (ETU)
Free Drop No. 1 is a NCT free drop from a height of three feet, impacting horizontally on the ETU side, parallel to the forklift pockets, nearly opposite the OCV vent port. The 3-foot drop height is based on the requirements of 10 CFR
&sect;71.71(c)(7) for a package weight between 11,000 and 22,000 pounds. The purpose of this drop test is to demonstrate that the NCT free drop does not compromise the ability of the HalfPACT package to successfully sustain subsequent HAC test events in the same or other orientations.
2.10.3-19
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Free Drop No. 2 is a HAC free drop from a height of 30 feet, impacting horizontally on the ETU side, parallel to the forklift pockets, nearly opposite the OCV vent port. In this way, NCT and HAC free drop damage is cumulative. The 30-foot drop height is based on the requirements of 10 CFR &sect;71.73(c)(1). The purpose of Free Drops Nos. 1 and 2, combined with Puncture Drop No. 7, is to create the greatest possible cumulative damage (i.e.,
the greatest reduction in foam thickness) in a region punctured through the OCA outer shell.
Free Drop No. 3 is a NCT free drop from a height of three feet, impacting horizontally on the ETU side, with the OCV vent port oriented downward. The 3-foot drop height is based on the requirements of 10 CFR &sect;71.71(c)(7) for a package weight between 11,000 and 22,000 pounds. The purpose of this drop test is to demonstrate that the NCT free drop does not compromise the ability of the HalfPACT package to successfully sustain subsequent HAC test events in the same or other orientations.
Free Drop No. 4 is a HAC free drop from a height of 30 feet, impacting horizontally on the ETU side, with the OCV vent port oriented downward. In this way, NCT and HAC free drop damage is cumulative.
The 30-foot drop height is based on the requirements of 10 CFR &sect;71.73(c)(1).
The purpose of Free Drops Nos. 3 and 4, combined with Puncture Drop No. 8, is to create the greatest possible cumulative damage (i.e., the greatest reduction in foam thickness) over the OCV vent port.
2.10.3-20
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Free Drop No. 5 is a NCT free drop from a height of three feet, impacting the ETU bottom corner perpendicular to the forklift pockets, with the packages center of gravity over the impact point. The 3-foot drop height is based on the requirements of 10 CFR &sect;71.71(c)(7) for a package weight between 11,000 and 22,000 pounds. The purpose of this drop test is to demonstrate that the NCT free drop does not compromise the ability of the HalfPACT package to successfully sustain subsequent HAC test events in the same or other orientations.
Free Drop No. 6 is a HAC free drop from a height of 30 feet, impacting the ETU bottom corner perpendicular to the forklift pockets, with the packages center of gravity over the impact point. In this way, NCT and HAC free drop damage is cumulative. The 30-foot drop height is based on the requirements of 10 CFR
&sect;71.73(c)(1). The purpose of Free Drops Nos. 5 and 6, combined with Puncture Drop No. 9, is to create the greatest possible cumulative damage in a region not tested during TRUPACT-II testing.
Puncture Drop No. 7 impacts directly onto the damage created by Free Drop Tests 1 and 2, directly below the 3/8-to-1/4-inch, OCA outer shell transition. The puncture drop height is based on the requirements of 10 CFR &sect;71.73(c)(3).
The purpose of Puncture Drop No. 7 is to breach the 1/4-inch thick OCA outer shell.
Testing of this package region, when cumulatively damaged from the free drops, puncture drop, and fire testing demonstrate that containment integrity is maintained for the main OCV O-ring seal.
2.10.3-21
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Puncture Drop No. 8 impacts directly onto the OCV vent port opening, compounding the cumulative damage created by Free Drop Tests 3 and 4. The puncture drop height is based on the requirements of 10 CFR &sect;71.73(c)(3).
The purpose of Puncture Drop No. 8 is to create the greatest cumulative damage (i.e., greatest reduction in foam thickness) over the OCV vent port region. Testing of this package region, when cumulatively damaged from the free drops, puncture drop, and fire testing, demonstrate that containment integrity is maintained for the OCV vent port O-ring seal.
Puncture Drop No. 9 impacts directly onto the cumulative damage created by Free Drop Tests 5 and 6. The puncture drop height is based on the requirements of 10 CFR &sect;71.73(c)(3). The purpose of Puncture Drop No. 9 is to create the greatest possible cumulative damage in a region not tested during TRUPACT-II testing. Testing of this package region, when cumulatively damaged from the free drops, puncture drop, and fire testing, demonstrates that containment integrity is maintained for the main OCV O-ring containment seal.
Puncture Drop No. 10 impacts directly above the 3/8-to-1/4-inch transition in the OCA body outer shell. The puncture drop height is based on the requirements of 10 CFR &sect;71.73(c)(3). The purpose of Puncture Drop No. 10 is to attempt to break the circumferential weld at the 3/8-to-1/4-inch transition in the OCA body outer shell. Testing of this package region, when cumulatively damaged from the puncture drop and fire tests, demonstrates that containment integrity is maintained for the OCV vent port and main O-ring containment seals.
2.10.3-22
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Fire No. 11 is performed by orienting the cumulative damage from Free Drop Tests 1 and 2, and Puncture Drop Test 7 at the hottest location in the fire (i.e.,
one meter above the fuel surface). The puncture damage from Puncture Drop No. 10 is oriented above the hole created by Puncture Drop No. 7 in an attempt to create a chimney through the foam cavity inside the OCA body.
2.10.3-23
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 2.10.3.6.2 Certification Test Unit (CTU)
Free Drop No. 1 is a NCT free drop from a height of three feet, impacting horizontally on the CTU side, with the OCV vent port oriented downward. The 3-foot drop height is based on 10 CFR
&sect;71.71(c)(7) for a package weight between 11,000 and 22,000 pounds. The purpose of this drop test is to demonstrate that the NCT free drop does not compromise the ability of the HalfPACT package to successfully sustain the subsequent HAC test events in the same or other orientations.
Free Drop No. 2 is a HAC free drop from a height of 30 feet, impacting horizontally on the CTU side, with the OCV vent port oriented downward. In this way, NCT and HAC free drop damage is cumulative.
The 30-foot drop height is based on the requirements of 10 CFR &sect;71.73(c)(1).
The purpose of Free Drops Nos. 1 and 2, combined with Puncture Drop No. 4, is to create the greatest possible cumulative damage (i.e., the greatest reduction in foam thickness) over the OCV vent port.
Free Drop No. 3 is a HAC free drop from a height of 30 feet, impacting 5&#xba; from horizontal with primary impact on the lid and secondary impact on a body tie-down lug. Although shown in Section 2.10.3.5.2.4, Closure (Lid) Separation, to be bounded by TRUPACT-II certification testing, the purpose of this drop is to apply the greatest separation forces to the closures. This test demonstrates retention of the lids, and that containment integrity is not compromised by this worst-case slapdown condition.
2.10.3-24
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Puncture Drop No. 4 impacts directly onto the OCV vent port opening, compounding the damage created by Free Drop Tests 1 and 2. The puncture drop height is based on the requirements of 10 CFR &sect;71.73(c)(3). The purpose of Puncture Drop No. 4 is to create the greatest cumulative damage (i.e., greatest reduction in foam thickness) over the OCV vent port region, thereby demonstrating that containment integrity is maintained for the OCV vent port O-ring seal.
Puncture Drop No. 5 impacts directly above the 3/8-to-1/4-inch transition in the OCA body outer shell. The puncture drop height is based on the requirements of 10 CFR &sect;71.73(c)(3). The purpose of Puncture Drop No. 5 is to attempt to break the circumferential weld at the 3/8-to-1/4-inch transition in the OCA body outer shell. Testing of this package region, when cumulatively damaged from the puncture drop and fire tests, demonstrates that containment integrity is maintained for the OCV vent port and main O-ring containment seals.
Puncture Drop No. 6 impacts directly onto the damage created by Free Drop Tests 1 and 2, directly below the 3/8-to-1/4-inch, OCA outer shell transition. The puncture drop height is based on the requirements of 10 CFR &sect;71.73(c)(3).
The purpose of Puncture Drop No. 6 is to breach the 1/4-inch thick OCA outer shell.
Testing of this package region, when cumulatively damaged from the free drops, puncture drop, and fire testing demonstrate that containment integrity is maintained for the main OCV O-ring seal.
2.10.3-25
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Fire No. 7 is performed by orienting the cumulative damage from Free Drop Tests 1 and 2, and Puncture Drop Test 4, at the hottest location in the fire (i.e., one meter above the fuel surface). In addition, the package is oriented to include the puncture damage from Puncture Drop No. 5 at the hottest location in the fire, directly opposite the damage from Free Drop Tests 1 and 2, and Puncture Drop Test 4.
2.10.3.7 Test Results The following sections report the results of free drop, puncture drop, and fire tests following the sequence provided in Section 2.10.3.6, Test Sequence for Selected Free Drop, Puncture Drop, and Fire Tests. Results are summarized in Table 2.10.3-2 and Table 2.10.3-3 for the ETU and CTU, respectively (also, see Figure 2.10.3-9 and Figure 2.10.3-10, respectively).
As can be seen in the subsequent sections, overall deformation and temperature results agree closely with those reported in the TRUPACT-II SAR.
Figure 2.10.3-12 through Figure 2.10.3-95 sequentially photo-document the engineering and certification testing process for the HalfPACT ETU and CTU, respectively.
2.10.3.7.1 Engineering Test Unit (ETU) 2.10.3.7.1.1 ETU Free Drop Test No. 1 Free Drop No. 1 was a NCT free drop from a height of three feet, impacting horizontally on the ETU side, parallel to the forklift pockets, nearly opposite the OCV vent port. As shown in Figure 2.10.3-9, the HalfPACT ETU was oriented horizontal to the impact surface (meridional angle (i.e., pitch) = 0&#xba;), and circumferentially aligned to impact 200&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented vertically). The following list summarizes the test parameters:
* verified meridional angle as 0&#xba; +/-1&#xba;
* verified circumferential angle to be 200&#xba; +/-1&#xba;
* verified free drop height as 3 feet, +1/-0 inches (actual drop height 3 feet, 1/2 inches)
* measured temperature at 53 &#xba;F at time of test
* conducted test at 9:54 a.m. on Tuesday, 2/18/97 A very slight rebound (bounce) occurred upon impact. The measured permanent deformations of the ETU were flats 16 inches wide at the OCA top, and 18 inches wide at the OCA bottom, corresponding to a crush depth of approximately 3/4 inches. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 1, the measured permanent deformations were flats 18 inches wide at both the OCA top and bottom.
2.10.3-26
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 2.10.3.7.1.2 ETU Free Drop Test No. 2 Free Drop No. 2 was a HAC free drop from a height of 30 feet, impacting horizontally on the ETU side, parallel to the forklift pockets, nearly opposite the OCV vent port. As shown in Figure 2.10.3-9, the HalfPACT ETU was oriented horizontal to the impact surface (meridional angle (i.e., pitch) = 0&#xba;), and circumferentially aligned to impact 200&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented vertically). The following list summarizes the test parameters:
* verified meridional angle as 0&#xba; +/-1&#xba;
* verified circumferential angle to be 200&#xba; +/-1&#xba;
* verified free drop height as 30 feet, +3/-0 inches (actual drop height 30 feet, 1 inch)
* measured temperature at 57 &#xba;F at time of test
* conducted test at 1:10 p.m. on Tuesday, 2/18/97 A small rebound (bounce) occurred upon impact. The measured permanent deformations of the ETU were flats 36 inches wide at the OCA top, and 33 inches wide at the OCA bottom, corresponding to a crush depth of approximately 31/4 inches. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 2, the measured permanent deformation were flats 37 inches wide at the OCA top, and 35 inches wide at the OCA bottom.
2.10.3.7.1.3 ETU Free Drop Test No. 3 Free Drop No. 3 was a NCT free drop from a height of three feet, impacting horizontally on the ETU side, with the OCV vent port oriented downward. As shown in Figure 2.10.3-9, the ETU was oriented horizontal to the impact surface (meridional angle (i.e., pitch) = 0&#xba;), and circumferentially aligned to impact directly onto the OCV vent port. The following list summarizes the test parameters:
* verified meridional angle as 0&#xba; +/-1&#xba;
* verified circumferential angle to be 0&#xba; +/-1&#xba;
* verified free drop height as 3 feet, +1/-0 inches (actual drop height 3 feet, 3/4 inches)
* measured temperature at 40 &#xba;F at time of test
* conducted test at 10:20 a.m. on Wednesday, 2/19/97 A very slight rebound (bounce) occurred upon impact. The measured permanent deformation of the ETU were flats 18 inches wide at both the OCA top and bottom, corresponding to a crush depth of approximately 3/4 inches. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 1, the measured permanent deformations were flats 18 inches wide at both the OCA top and bottom.
2.10.3.7.1.4 ETU Free Drop Test No. 4 Free Drop No. 4 was a HAC free drop from a height of 30 feet, impacting horizontally on the ETU side, with the OCV vent port oriented downward. As shown in Figure 2.10.3-9, the ETU was oriented horizontal to the impact surface (meridional angle (i.e., pitch) = 0&#xba;), and circumferentially aligned to impact directly onto the OCV vent port. The following list summarizes the test parameters:
2.10.3-27
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
* verified meridional angle as 0&#xba; +/-1&#xba;
* verified circumferential angle to be 0&#xba; +/-1&#xba;
* verified drop height as 30 feet, +3/-0 inches (actual drop height 30 feet, 2 inches)
* measured temperature at 48 &#xba;F at time of test
* conducted test at 1:47 p.m. on Wednesday, 2/19/97 A small rebound (bounce) occurred upon impact. The measured permanent deformations of the ETU were flats 34 inches wide at both the OCA top and bottom, corresponding to a crush depth of approximately 31/4 inches. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 2, the measured permanent deformation were flats 37 inches wide at the OCA top, and 35 inches wide at the OCA bottom.
2.10.3.7.1.5 ETU Free Drop Test No. 5 Free Drop No. 5 was a NCT free drop from a height of three feet, impacting the ETU bottom corner perpendicular to the forklift pockets, with the packages center of gravity over the impact point. As shown in Figure 2.10.3-9, the ETU was oriented at an angle 43&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 43&#xba;), and circumferentially aligned to impact 110&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented horizontally). The following list summarizes the test parameters:
* verified meridional angle as 43&#xba; +/-1&#xba;
* verified circumferential angle to be 110&#xba; +/-1&#xba;
* verified free drop height as 3 feet, +1/-0 inches (actual drop height 3 feet, 5/8 inches)
* measured temperature at 53 &#xba;F at time of test
* conducted test at 10:14 a.m. on Thursday, 2/20/97 A very slight rebound (bounce) occurred upon impact. The measured permanent deformation of the ETU was a flat 26 inches long and 51/2 inches wide at the bottom corner, corresponding to a crush depth of approximately 1 inches. No applicable comparison is available from the TRUPACT-II SAR.
2.10.3.7.1.6 ETU Free Drop Test No. 6 Free Drop No. 6 was a HAC free drop from a height of 30 feet, impacting the ETU bottom corner perpendicular to the forklift pockets, with the packages center of gravity over the impact point. As shown in Figure 2.10.3-9, the ETU was oriented at an angle 43&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 43&#xba;), and circumferentially aligned to impact 110&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented horizontally). The following list summarizes the test parameters:
* verified meridional angle as 43&#xba; +/-1&#xba;
* verified circumferential angle to be 110&#xba; +/-1&#xba;
* verified free drop height as 30 feet, +1/-0 inches (actual drop height 30 feet, 1 inch)
* measured temperature at 55 &#xba;F at time of test 2.10.3-28
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
* conducted test at 1:53 p.m. on Thursday, 2/20/97 A small rebound (bounce) occurred upon impact. The measured permanent deformation of the ETU was a flat 40 inches long and 12 inches wide at the bottom corner, corresponding to a crush depth of approximately 31/4 inches. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 3, the measured permanent deformation was a flat 53 inches long and 30 inches wide at the top corner (on the knuckle radius of the torispherical head), corresponding to a crush depth of approximately 33/4 inches.
2.10.3.7.1.7 ETU Puncture Drop Test No. 7 Puncture Drop No. 7 impacted directly onto the damage created by Free Drop Tests 1 and 2, directly below the 3/8-to-1/4-inch, OCA outer shell transition. As shown in Figure 2.10.3-9, the ETU was oriented at an angle 20&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 20&#xba;), and circumferentially aligned to impact 200&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented vertically). This orientation placed the puncture bar impact directly adjacent to and below the 3/8-to-1/4-inch thick transition in the OCA body outer shell (i.e., on the 1/4-inch thick shell). The following list summarizes the test parameters:
* verified meridional angle as 20&#xba; +/-1&#xba;
* verified circumferential angle to be 200&#xba; +/-1&#xba;
* verified puncture drop height as 40 +1/-0 inches (actual drop height 401/4 inches)
* measured temperature at 38 &#xba;F at time of test
* conducted test at 11:04 a.m. on Friday, 2/21/97 The puncture drop penetrated the OCA outer shell in the region damaged by Free Drop Tests 1 and 2. The measured permanent deformation of the ETU was a hole 101/2 inches long and 111/2 inches wide, measuring 8 inches deep radially and 11 inches deep along the axis of the puncture bar. Although no direct comparison is available, similar results may be obtained from the TRUPACT-II SAR. As shown in the TRUPACT-II SAR for CTU No. 1, Test 7, a similar hole occurred in the CTU body approximately 12 inches long. Further, as shown in the TRUPACT-II SAR for CTU No. 2, Test R, a similar hole occurred in the CTU body approximately 91/2 inches deep along the axis of the puncture bar. From the TRUPACT-II SAR for CTU No. 2, Test 4, a similar hole occurred in the CTU head approximately 7 inches deep along the axis of the puncture bar. From the TRUPACT-II SAR for CTU No. 3, Test 4, a similar hole occurred in the CTU body approximately 8 inches deep along the axis of the puncture bar. Of final note, from the TRUPACT-II SAR for CTU No. 2, Test 4, similar puncture bar damage occurred at approximately the same distance from the main OCV containment O-ring seal as the damage produced on the HalfPACT ETU for this test.
2.10.3.7.1.8 ETU Puncture Drop Test No. 8 Puncture Drop No. 8 impacted directly onto the OCV vent port opening, compounding the cumulative damage created by Free Drop Tests 3 and 4. As shown in Figure 2.10.3-9, the ETU was oriented at an angle 1&#xba; from horizontal relative to the impact surface (meridional angle (i.e.,
pitch) = 1&#xba;), and circumferentially aligned to impact directly onto the OCV vent port. The following list summarizes the test parameters:
2.10.3-29
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
* verified meridional angle as 1&#xba; +/-1&#xba; (i.e., package top-end slightly raised)
* verified circumferential angle to be 0&#xba; +/-1&#xba;
* verified puncture drop height as 40 +1/-0 inches (actual drop height 40 inches)
* measured temperature at 40 &#xba;F at time of test
* conducted test at 2:42 p.m. on Friday, 2/21/97 The puncture drop impacted the OCA outer shell in the region damaged by Free Drop Tests 3 and 4, and was offset approximately six inches from the OCV vent port due to high crosswinds.
The measured permanent deformation of the ETU was a non-penetrating radial dent 21/2 inches deep. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 5, the measured permanent deformation was a non-penetrating radial dent 3 inches deep.
2.10.3.7.1.9 ETU Puncture Drop Test No. 9 Puncture Drop No. 9 impacts directly onto the cumulative damage created by Free Drop Tests 5 and 6. As shown in Figure 2.10.3-9, the ETU was oriented at an angle 43&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 43&#xba;), and circumferentially aligned to impact 110&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented horizontally). This orientation placed the puncture bar impact directly over the OCA bottom corner onto the damage created by Free Drop Tests 5 and 6. The following list summarizes the test parameters:
* verified meridional angle as 43&#xba; +/-1&#xba;
* verified circumferential angle to be 110&#xba; +/-1&#xba;
* verified puncture drop height as 40 +1/-0 inches (actual drop height 401/4 inches)
* measured temperature at 28 &#xba;F at time of test
* conducted test at 12:26 p.m. on Monday, 2/24/97 The puncture drop impacted the OCA outer shell, centered on the corner drop damage created by drop tests 5 and 6. The measured permanent deformation of the ETU was a dent 3 inches deep along the axis of the puncture bar, with no penetration. In comparison, from the TRUPACT-II SAR for CTU No. 2, Test 5, resulted in a measured permanent deformation as a dent approximately 5 inches deep along the axis of the puncture bar.
2.10.3.7.1.10 ETU Puncture Drop Test No. 10 Puncture Drop No. 10 impacted directly above the 3/8-to-1/4-inch transition in the OCA body outer shell. As shown in Figure 2.10.3-9, the ETU was oriented at an angle 9&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 9&#xba;), and circumferentially aligned to impact 290&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented horizontally). This orientation placed the puncture bar impact directly adjacent to and above the 3/8-to-1/4 inch-thick transition in the OCA body outer shell (i.e., on the 3/8-inch thick shell). The following list summarizes the test parameters:
* verified meridional angle as 9&#xba; +/-1&#xba;
* verified circumferential angle to be 290&#xba; +/-1&#xba; 2.10.3-30
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022
* verified puncture drop height as 40 +1/-0 inches (actual drop height 401/4 inches)
* measured temperature at 29 &#xba;F at time of test
* conducted test at 11:43 a.m. on Tuesday, 2/25/97 The puncture drop impacted the OCA outer shell in a region with no previous damage. The measured permanent deformation of the ETU was a circumferential tear along the 3/8-to-1/4 transition weld, approximately 27 inches long and 51/2 inches deep radially. No applicable comparison is available from the TRUPACT-II SAR.
2.10.3.7.1.11 ETU Fire Test No. 11 Fire No. 11 was performed to demonstrate packaging compliance with the requirements of 10 CFR 71, and followed the guidelines set forth in IAEA Safety Series No. 37 14. The following list summarizes the test parameters:
* Consistent with the TRUPACT-II SAR, the HalfPACT ETU was oriented on an insulated test stand (identical to the test stand used for TRUPACT-II fire testing) such that the most severe damage was approximately 11/2 meters above the fuel surface. With a circumferential orientation of 146&#xba; (see Figure 2.10.3-9), the most severe damage was determined to be from the cumulative effects of free drop tests 1 and 2, and puncture drop test 7, followed by additional damage due to puncture drop test 10. Thus, the hole caused by puncture drop test 7 was located 11/2 meters above the fuel surface, and the damage from puncture drop test 10 was located above the hole, approximately 3 meters above the fuel surface. Orienting the HalfPACT ETU this way maximized the potential for a chimney 15 to form between the penetrating damage from puncture drop tests 7 and 10.
* Consistent with Paragraph A-628.4 of IAEA Safety Series No. 37, the HalfPACT ETU was installed onto the insulated test stand at an elevation to place the lowest part of the package one meter above the fuel surface. The ETU was oriented horizontally on the test stand to maximize heat input.
* Consistent with Paragraph A-628.4 of IAEA Safety Series No. 37, requiring the test pool to extend 1 to 3 meters beyond the package edges, the test pool size extended approximately 11/2 meters beyond each side of the ETU.
* Consistent with Paragraph A-628.5 of IAEA Safety Series No. 37, requiring wind speeds not to exceed 2 m/s (4.5 mph), a balloon was released that demonstrated both ground level and 1,000 feet altitude wind speeds under 5 mph. Weather conditions included a high altitude overcast, without precipitation for the duration of the fire test. Further, wind baffles were erected to surround the test pool to reduce the possible effects of wind gusts. The time-averaged wind speed during the fire test was approximately 1 mph both outside and inside the test area.
* Consistent with Paragraphs A-628.6 and A-628.8 of IAEA Safety Series No. 37, a JP4-type fuel was used for the fire test, and the amount of fuel was controlled to ensure the fire 14 IAEA Safety Series No. 37, Advisory Material for the IAEA Regulations for the Safe Transport of Radioactive Material (1985 Edition), Third Edition (As Amended 1990), International Atomic Energy Agency, Vienna, 1990.
15 A chimney is characterized as a preferentially burning, convective flow channel from one opening to another.
The formation of a chimney can cause severe erosion of the underlying insulating polyurethane foam thereby creating localized hot spots that could, in-turn, prevent the packaging from performing as intended.
2.10.3-31
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 duration exceeded 30 minutes. The fuel was floated on a pool of water approximately 1/2 meter deep to ensure even distribution during burning. The fire test lasted approximately 33 minutes, and burning continued for approximately 45 minutes after the end of the fire.
* Consistent with Paragraphs A-628.7 and A-628.9 of IAEA Safety Series No. 37, the test pool was instrumented to measure fire temperatures and heat fluxes at various locations around the ETU. Temperatures and heat fluxes were monitored before, during, and following the fire test until magnitudes stabilized back to ambient conditions. The average and standard deviation of the measured flame temperature was 1,575 +/- 191 &#xba;F, and the average and standard deviation of the measured heat flux was 8.2 +/- 3.8 Btu/ft2-s.
* Consistent with Paragraph A-628.10 of IAEA Safety Series No. 37, the ETU containment O-ring seals were leakage rate tested following performance testing to verify containment integrity. Discussions regarding post-test leakage rate testing are provided in Section 2.10.3.7.1.12, ETU Post-Test Disassembly.
* Commenced fire testing (fire ignition) at 7:50 a.m. on Tuesday, 3/4/97. The ambient temperature was 43 &#xba;F at the start of the fire test.
Similar observations and results were noted in the TRUPACT-II SAR for fire testing. Since no instrumentation was utilized to measure HalfPACT ETU temperatures from fire testing, no direct comparison can be made to the reported TRUPACT-II CTU temperatures.
2.10.3.7.1.12 ETU Post-Test Disassembly Post-test disassembly of the HalfPACT ETU was performed during the week of Monday, 3/10/97, through Friday, 3/14/97. Both abrasive cutting and gas plasma cutting methods were utilized, depending on their potential affect on subsequent post-test seal testing, to enable opening the ETU.
Upon removal of the OCA lid and body outer shells, the presence of several inches of very light density foam char that showed the intumescent behavior of the polyurethane foam. An average of 11 inches of undamaged foam was measured throughout the torispherical head region in the OCA lid. In regions remote from side drop damage, an average of 5 inches of undamaged foam was measured through the OCA lid side. In regions of side drop damage, an average of 3 inches of undamaged foam was measured through the OCA lid side. On a per-volume basis estimate, more than 80% of the polyurethane foam in the OCA lid remained undamaged.
Similarly, approximately 5 inches of undamaged foam was measured at the bottom center of the OCA body. In regions remote from side drop damage, an average of 6 inches of undamaged foam was measured through the OCA body side. In regions of side drop damage, an average of 3 inches of undamaged foam was measured through the OCA body side. On a per-volume basis estimate, more than 50% of the polyurethane foam in the OCA body remained undamaged.
In comparison, the TRUPACT-II packaging certification test units exhibited nearly identical amounts of undamaged polyurethane foam with a minimum of 5 inches remaining around the OCV except in localized regions damaged by free and puncture drops.
Upon removal of all the remaining polyurethane foam and ceramic fiber paper material, the OCV lid and body appeared lightly damaged. Some minor flattening was noted along the axes of the three sets of free drops (i.e., free drop tests 1 and 2, 3 and 4, and 5 and 6). Thus, damage to the OCV was mostly due to external application of force (i.e., due to the free drop and puncture drop tests). The ICV, however, appeared to have greater deformation coinciding with the axes of the 2.10.3-32
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 55-gallon payload drums. In contrast to the OCV, damage to the ICV was mostly due to an internal application of force caused by the greater weight capacity of the HalfPACT payload drums compared to that of the TRUPACT-II payload drums. The result was that the HalfPACT ETU ICV exhibited larger permanent deformation than compared to that of the TRUPACT-II CTUs. Several of the 55-gallon payload drums were distorted sufficiently to cause loss of their lids, as similarly noted for TRUPACT-II certification testing. Of final note, additional damage to the ETU ICV may have been caused by the 5+ inches of excess axial gap above the payload drums, since a payload spacer was not used for the HalfPACT ETU. This surplus axial gap could have allowed the non-immobilized payload drums to bounce excessively thereby compounding the effect of increased payload drum weight.
Demonstration of containment vessel leaktightness was accomplished by installing 3/8 NPT ports through the knuckle region of the OCV and ICV lid torispherical heads to allow evacuation and subsequent backfill of each corresponding containment vessel cavity with helium gas. This method ensured helium gas was present behind each containment seal, thereby validating the testing process. Although performed prior to beginning the ETU testing program, helium leakage rate testing was not performed on either of the metallic containment boundaries following testing of the ETU. Results of successful mass spectrometer helium leakage rate testing are summarized below:
Sealing Component                                  OCV                            ICV
                                                            -8                            -8 Main O-ring Seal                    <1.0 x 10 cc/s, helium          7.8 x 10 cc/s, helium Vent Port Plug O-ring Seal                  3.6 x 10-8 cc/s, helium      3.0 x 10-8 cc/s, helium When accounting for the conversion between air leakage (per ANSI N14.5) and helium leakage, a 2.6 factor applies for standard temperatures and pressures. Thus, a reported helium leakage rate of 7.8 x 10-8 cc/s, helium, is equivalently 3.9 x 10-8 cc/s, air, a magnitude well below the leaktight criterion of 1 x 10-7 cc/s, air, per ANSI N14.5.
The ICV wiper O-ring seal ring was damaged somewhat (buckled) in two locations due to failure of several adjacent drive screws. Thus, some of the payload drum filler material appeared to be forced into the region above the wiper O-ring seal. Both the damage to the wiper seal ring and presence of residual material in the wiper seal region were identically noted for the TRUPACT-II CTUs. As noted earlier, however, all containment O-ring seals successfully passed subsequent helium leakage rate testing thereby clearly demonstrating that containment integrity was maintained.
In conclusion, overall damage to the HalfPACT ETU paralleled the measured damage from TRUPACT-II certification testing. This was expected due to the close overall similarities between packages.
2.10.3.7.2 Certification Test Unit (CTU)
Performance testing in accordance with the requirements of 10 CFR &sect;71.71 and &sect;71.73 for free drops, puncture drops, and fire testing was performed based on a certification test plan prepared specifically for the HalfPACT certification testing program 16.
16 S. A. Porter, et al, Certification Test Plan for the HALFPACK Package, TP-005, Rev. 1, March 6, 1998, Packaging Technology, Inc. (PacTec), Tacoma, Washington.
2.10.3-33
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 2.10.3.7.2.1 CTU Free Drop Test No. 1 Free Drop No. 1 was a NCT free drop from a height of three feet, impacting horizontally on the CTU side, with the OCV vent port oriented downward. As shown in Figure 2.10.3-10, the CTU was oriented horizontal to the impact surface (meridional angle (i.e., pitch) = 0&#xba;), and circumferentially aligned to impact directly onto the OCV vent port. The following list summarizes the test parameters:
* verified meridional angle as 0&#xba; +/-1&#xba;
* verified circumferential angle to be 0&#xba; +/-1&#xba;
* verified free drop height as 3 feet, +1/-0 inches (actual drop height 3 feet, 1/2 inches)
* measured temperature at 52 &#xba;F at time of test
* conducted test at 4:54 p.m. on Monday, 3/16/98 A very slight rebound (bounce) occurred upon impact. The measured permanent deformation of the CTU were flats 13 inches wide at both the OCA top and bottom, corresponding to a crush depth of approximately 1/2 inches. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 1, the measured permanent deformations were flats 18 inches wide at both the OCA top and bottom.
Further, for HalfPACT ETU, Free Drop Test 1, presented in Table 2.10.3-2, the measured permanent deformations were flats 16 inches wide at the OCA top, and 18 inches wide at the OCA bottom. Finally, for HalfPACT ETU, Free Drop Test 3, also presented in Table 2.10.3-2, the measured permanent deformations were flats 18 inches wide at both the OCA top and bottom.
2.10.3.7.2.2 CTU Free Drop Test No. 2 Free Drop No. 2 was a HAC free drop from a height of 30 feet, impacting horizontally on the CTU side, with the OCV vent port oriented downward. As shown in Figure 2.10.3-10, the CTU was oriented horizontal to the impact surface (meridional angle (i.e., pitch) = 0&#xba;), and circumferentially aligned to impact directly onto the OCV vent port. The following list summarizes the test parameters:
* verified meridional angle as 0&#xba; +/-1&#xba;
* verified circumferential angle to be 0&#xba; +/-1&#xba;
* verified free drop height as 30 feet, +3/-0 inches (actual drop height 30 feet, 1 inch)
* measured temperature at 50 &#xba;F at time of test
* conducted test at 11:32 a.m. on Tuesday, 3/17/98 A small rebound (bounce) occurred upon impact. The measured permanent deformation of the CTU were flats 37 inches wide at both the OCA top and bottom, corresponding to a crush depth of approximately 33/4 inches. In comparison, from the TRUPACT-II SAR for CTU No. 1, Test 2, the measured permanent deformation were flats 37 inches wide at the OCA top, and 35 inches wide at the OCA bottom. Further, for HalfPACT ETU, Free Drop Test 2, presented in Table 2.10.3-2, the measured permanent deformations were flats 36 inches wide at the OCA top, and 33 inches wide at the OCA bottom. Finally, for HalfPACT ETU, Free Drop Test 3, also presented in Table 2.10.3-2, the measured permanent deformations were flats 34 inches wide at both the OCA top and bottom.
2.10.3-34
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 2.10.3.7.2.3 CTU Free Drop Test No. 3 Free Drop No. 4 was a HAC free drop from a height of 30 feet, impacting 5&#xba; from horizontal with primary impact on the lid and secondary impact on a body tie-down lug. As shown in Figure 2.10.3-10, the CTU was oriented at an angle 5&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 5&#xba;), and circumferentially aligned to impact 1471/2&#xba; from the OCA vent port (aligned with a tie-down lug). The following list summarizes the test parameters:
* verified meridional angle as 5&#xba; +/-1&#xba;
* verified circumferential angle to be 1471/2&#xba; +/-1&#xba;
* verified drop height as 30 feet, +3/-0 inches (actual drop height 30 feet, 1 inch)
* measured temperature at 41 &#xba;F at time of test
* conducted test at 11:50 a.m. on Wednesday, 3/18/98 A small rebound (bounce) occurred upon impact. The measured permanent deformation of the CTU was a flat 411/2 inches wide at the OCA top, corresponding to a crush depth at the OCA lid of approximately 41/4 inches. In comparison, from the TRUPACT-II SAR for CTU No. 2, Test 1, the measured permanent deformation was a flat 45 inches wide at the OCA top. Also, from the TRUPACT-II SAR for CTU No. 3, Test 1, the measured permanent deformation was a flat 48 inches wide at the OCA top. Note that Tests 1 for TRUPACT-II CTU Nos. 2 and 3 were performed at cold temperature conditions (-20 &#xba;F). Had the TRUPACT-II slapdown drops been performed at ambient temperature conditions such as the case for HalfPACT CTU, Free Drop Test 3, the corresponding TRUPACT-II deformations would have been greater. These results correspond with the discussions from Section 2.10.3.5.2.4, Closure (Lid) Separation, where it is shown that TRUPACT-II slapdown drop testing bounds HalfPACT slapdown drop testing.
Of final note, approximately two inches of separation of the OCA Z-flanges was measured. The magnitude of this separation corresponds to the amount observed during TRUPACT-II slapdown testing. Regardless, the generous overlap of the OCA outer thermal shield provided sufficient protection of the OCA Z-flange gap for the subsequent fire test.
2.10.3.7.2.4 CTU Puncture Drop Test No. 4 Puncture Drop No. 4 impacted directly onto the OCV vent port opening, compounding the cumulative damage created by Free Drop Tests 1 and 2. As shown in Figure 2.10.3-10, the CTU was oriented at an angle 11/2&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 11/2&#xba;), and circumferentially aligned to impact directly onto the OCV vent port. The following list summarizes the test parameters:
* verified meridional angle as 11/2&#xba; +/-1&#xba; (i.e., package top-end slightly raised)
* verified circumferential angle to be 0&#xba; +/-1&#xba;
* verified puncture drop height as 40 +1/-0 inches (actual drop height 401/2 inches)
* measured temperature at 42 &#xba;F at time of test
* conducted test at 10:24 a.m. on Thursday, 3/19/98 2.10.3-35
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 The puncture drop impacted the OCA outer shell in the region damaged by Free Drop Tests 1 and 2, directly onto the OCV vent port. The measured permanent deformation of the CTU was a non-penetrating radial dent 33/4 inches deep. In comparison, from the TRUPACT-II SAR for CTU No.
1, Test 5, the measured permanent deformation was a non-penetrating radial dent 3 inches deep.
Further, for HalfPACT ETU, Free Drop Test 8, presented in Table 2.10.3-2, the measured permanent deformation was a non-penetrating radial dent 21/2 inches deep. Regardless of the greater radial deformation noted for the HalfPACT CTU, OCV vent port region, subsequent fire and helium leakage rate testing demonstrated that containment integrity was maintained.
2.10.3.7.2.5 CTU Puncture Drop Test No. 5 Puncture Drop No. 5 impacted directly above the 3/8-to-1/4-inch transition in the OCA body outer shell. As shown in Figure 2.10.3-10, the CTU was oriented at an angle 16&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 16&#xba;), and circumferentially aligned to impact 250&#xba; from the OCA vent port. This orientation placed the puncture bar impact directly adjacent to and above the 3/8-to-1/4-inch thick transition in the OCA body outer shell (i.e., on the 3/8-inch thick shell). The following list summarizes the test parameters:
* verified meridional angle as 16&#xba; +/-1&#xba;
* verified circumferential angle to be 250&#xba; +/-1&#xba;
* verified puncture drop height as 40 +1/-0 inches (actual drop height 40 inches)
* measured temperature at 52 &#xba;F at time of test
* conducted test at 3:48 p.m. on Thursday, 3/19/98 The puncture drop impacted the OCA outer shell in a region with no previous damage. The measured permanent deformation of the CTU was a circumferential tear along the 3/8-to-1/4 transition weld, approximately 23 inches long and 4 inches deep radially. In comparison, the measured permanent deformation of the ETU was a circumferential tear along the 3/8-to-1/4 transition weld, approximately 27 inches long and 51/2 inches deep radially. No applicable comparison is available from the TRUPACT-II SAR.
2.10.3.7.2.6 CTU Puncture Drop Test No. 6 Puncture Drop No. 6 impacted directly below the 3/8-to-1/4-inch transition in the OCA body outer shell. As shown in Figure 2.10.3-10, the CTU was oriented at an angle 23&#xba; from horizontal relative to the impact surface (meridional angle (i.e., pitch) = 23&#xba;), and circumferentially aligned to impact 110&#xba; from the OCA vent port (between the tie-down lugs, with the forklift pockets oriented horizontally). This orientation placed the puncture bar impact directly adjacent to and below the 3/8-to-1/4-inch thick transition in the OCA body outer shell (i.e., on the 1/4-inch thick shell). The following list summarizes the test parameters:
* verified meridional angle as 23&#xba; +/-1&#xba;
* verified circumferential angle to be 110&#xba; +/-1&#xba;
* verified puncture drop height as 40 +1/-0 inches (actual drop height 401/4 inches)
* measured temperature at 52 &#xba;F at time of test
* conducted test at 12:19 p.m. on Friday, 3/20/97 2.10.3-36
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 The puncture drop impacted the OCA outer shell in a region with no previous damage. The measured permanent deformation of the CTU was a non-penetrating radial dent 31/2 inches deep.
In comparison, the measured permanent deformation of the HalfPACT ETU was a hole 101/2 inches long and 111/2 inches wide, measuring 8 inches deep radially and 11 inches deep along the axis of the puncture bar. Rather than penetrating, the puncture bar slid on the surface of the OCA outer shell until sufficient offset was achieved to allow the HalfPACT CTU to roll off the puncture bar. This result was due to lengthening the 3/8-inch thick, OCA outer shell from 12 to 18 inches, correspondingly changing the impact angle sufficiently to prevent penetration through the adjacent 1/4-inch thick shell.
2.10.3.7.2.7 CTU Fire Test No. 7 Fire No. 7 was performed to demonstrate packaging compliance with the requirements of 10 CFR 71, and followed the guidelines set forth in IAEA Safety Series No. 37. The following list summarizes the test parameters:
* Consistent with the TRUPACT-II SAR and the HalfPACT ETU, the HalfPACT CTU was oriented on an insulated test stand (identical to the test stand used for TRUPACT-II and HalfPACT ETU fire testing) such that the most severe damage was approximately 11/2 meters above the fuel surface. The most severe damage was determined to be from the cumulative effects of free drop tests 1 and 2, and puncture drop test 4, followed by additional damage due to puncture drop test 5. With a circumferential orientation of 305&#xba; (see Figure 2.10.3-10), the damage from the two sets of tests were located 11/2 meters above the fuel surface.
* Consistent with Paragraph A-628.4 of IAEA Safety Series No. 37, the HalfPACT CTU was installed onto the insulated test stand at an elevation to place the lowest part of the package one meter above the fuel surface. The CTU was oriented horizontally on the test stand to maximize heat input.
* Consistent with Paragraph A-628.4 of IAEA Safety Series No. 37, requiring the test pool to extend 1 to 3 meters beyond the package edges, the test pool size extended approximately 11/2 meters beyond each side of the CTU.
* Consistent with Paragraph A-628.5 of IAEA Safety Series No. 37, requiring wind speeds not to exceed 2 m/s (4.5 mph), a balloon was released that demonstrated both ground level and 1,000 feet altitude wind speeds under 5 mph at the start of the fire test. Weather conditions included relatively clear skies, without precipitation for the duration of the fire test. Further, wind baffles were erected to surround the test pool to reduce the possible effects of wind gusts. The time-averaged wind speed during the fire test was approximately 8 mph outside the test area, corresponding to approximately 4 mph inside the test area.
* Consistent with Paragraphs A-628.6 and A-628.8 of IAEA Safety Series No. 37, a JP4-type fuel was used for the fire test, and the amount of fuel was controlled to ensure the fire duration exceeded 30 minutes. The fuel was floated on a pool of water approximately 1/2 meter deep to ensure even distribution during burning. The fire test lasted approximately 33 minutes, and burning continued for approximately 30 minutes after the end of the fire.
* Consistent with Paragraphs A-628.7 and A-628.9 of IAEA Safety Series No. 37, the test pool was instrumented to measure fire temperatures and heat fluxes at various locations around the CTU. Temperatures and heat fluxes were monitored before, during, and following the 2.10.3-37
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 fire test until magnitudes stabilized back to ambient conditions. The average measured flame temperature was 1,486 &#xba;F.
* Consistent with Paragraph A-628.10 of IAEA Safety Series No. 37, the CTU containment O-ring seals were leakage rate tested following performance testing to verify containment integrity. Discussions regarding post-test leakage rate testing are provided in Section 2.10.3.7.2.8, CTU Post-Test Disassembly.
* Commenced fire testing (fire ignition) at 7:54 a.m. on Tuesday, 4/14/98. The ambient temperature was 51 &#xba;F at the start of the fire test.
No active temperature measuring devices were employed prior to, during, or following the HAC fire test. Further, measurement of the OCA outer shell temperature does not represent the OCV or ICV temperatures due to the large internal mass and thick, thermally insulating foam used within the OCA. As discussed in Section 3.1.1, Packaging, the temperatures of the OCV, ICV, and payload are effectively decoupled from the OCA outer shell and polyurethane foam for short term thermal transients. Instead, the initial temperature of the CTU may be estimated based on the ambient temperature of the Sandia National Laboratory testing facilities in the six weeks prior to the HAC fire test 17. Climatological data for Albuquerque, New Mexico, during the month of March and first two weeks of April 1998 shows an average temperature of 48 &#xba;F for those six weeks. Thus, when adjusting for the elevation difference between the testing facilities and Albuquerque, the initial temperature for fire testing is taken as 43 &#xba;F.
As stated in Section 3.5.1.1, Analytical Model, the initial condition temperatures for the HAC fire test are presented in Table 3.5-1. Accordingly, the average temperature of the ICV wall and OCV wall is 133 &#xba;F and 131 &#xba;F, respectively. Therefore, the difference between the theoretical pre-fire package temperature and actual adjusted starting temperature is conservatively taken as 133 &#xba;F - 43 &#xba;F = 90 &#xba;F.
The CTU utilized passive, non-reversible temperature indicating labels at various locations near each containment vessels seal flanges to record temperatures from the HAC fire test. Each set of temperature indicating labels recorded temperatures in 40 steps from 105 &#xba;F to 500 &#xba;F. As illustrated in Figure 2.10.3-11, some locations used redundant sets of temperature labels to ensure comprehensive results at critical regions.
A summary of temperature indicating label temperatures is presented in Table 2.10.3-4. The maximum measured OCV seal region temperature was 200 &#xba;F. Upwardly adjusting for the lower, pre-fire starting temperature by 90 &#xba;F results in a projected maximum OCV seal region temperature of 290 &#xba;F. The maximum measured ICV seal region temperature was 110 &#xba;F.
Similarly adjusting for the lower, pre-fire starting temperature by 90 &#xba;F results in a projected maximum ICV seal region temperature of 200 &#xba;F. In comparison, certification testing of the TRUPACT-II package showed a maximum OCV seal region temperature of 260 &#xba;F, and a maximum ICV seal region temperature of 200 &#xba;F (see the TRUPACT-II SAR). As with the comparison of measurements of drop damage, fire temperatures between the two similar package designs agree very well.
17 CTU was located at Sandia National Laboratories Coyote Canyon drop test facility for the month of March, 1998, and the Lurance Canyon burn facility for the first two weeks of April, 1998. CTU was burned on April 14, 1998. The elevation difference between the two test facilities and the city of Albuquerque results in an average ambient temperature approximately 5 &#xba;F cooler than Albuquerque.
2.10.3-38
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Two final observations are notable regarding fire testing. First, changing the OCV vent and seal test port thermal plugs from polyurethane foam to ceramic fiber paper material appears to have benefited the corresponding port plugs (compare ETU Figure 2.10.3-45, Figure 2.10.3-46, and Figure 2.10.3-47 to CTU Figure 2.10.3-84, Figure 2.10.3-86, and Figure 2.10.3-87). Second, with reference to Table 2.10.3-4, the temperature indicating labels (Nos. 3 and 7) at circumferential angle  = 250&#xba; read substantially lower temperatures than all other OCV locations. The reason is not known since the 250&#xba; location was positioned in the hottest location in the fire (i.e., 11/2 meters above the fuel surface).
2.10.3.7.2.8 CTU Post-Test Disassembly Post-test disassembly of the HalfPACT CTU was performed during the week of Monday, 4/26/98, through Friday, 5/8/98. To limit potentially misleading peripheral damage to the CTU during post-test disassembly, only abrasive cutting methods were utilized.
As with the ETU, upon removal of the OCA lid and body outer shells, the presence of several inches of very light density foam char that showed the intumescent behavior of the polyurethane foam. Undamaged foam thicknesses in the OCA lid closely paralleled those measured for the HalfPACT ETU. An average of 11 inches of undamaged foam was measured throughout the crown region of the OCA lid torispherical head, and 9 inches of undamaged foam in the knuckle region. In regions remote from side drop damage, an average of 5 inches of undamaged foam was measured through the OCA lid side. In regions of side drop damage, an average of 3 inches of undamaged foam was measured through the OCA lid side. On a per-volume basis estimate, more than 80% of the polyurethane foam in the OCA lid remained undamaged.
Similarly, approximately 61/2 inches of undamaged foam was measured at the bottom center of the OCA body. In regions remote from side drop damage, an average of 8 inches of undamaged foam was measured through the OCA body side. In regions of side drop damage, an average of 41/2 inches of undamaged foam was measured through the OCA body side. On a per-volume basis estimate, more than 70% of the polyurethane foam in the OCA body remained undamaged.
More undamaged foam remained in the OCA body for the CTU than for the ETU. This effect was most likely due to the presence of more wind during the CTU fire test, blowing from the package bottom toward the top. Regardless, the package closure region remained fully engulfed in the fire for the duration of the fire test.
In comparison, the TRUPACT-II packaging certification test units exhibited nearly identical amounts of undamaged polyurethane foam with a minimum of 5 inches remaining around the OCV except in localized regions damaged by free and puncture drops.
Upon removal of all the remaining polyurethane foam and ceramic fiber paper material, the OCV lid and body appeared lightly damaged. Some minor flattening was noted along the axes of the three free drops (i.e., free drop tests 1, 2, and 3). Thus, as with the ETU, damage to the OCV was mostly due to external application of force (i.e., due to the free drop and puncture drop tests). As with the ETU, the ICV, however, appeared to have greater deformation coinciding with the axes of the 55-gallon payload drums. In contrast to the OCV, damage to the ICV was mostly due to an internal application of force caused by the greater weight capacity of the HalfPACT payload drums compared to that of the TRUPACT-II payload drums. The result was that the HalfPACT CTU ICV exhibited larger permanent deformation than compared to that of 2.10.3-39
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 the TRUPACT-II CTUs. Several of the 55-gallon payload drums were distorted sufficiently to cause loss of their lids, as similarly noted for TRUPACT-II certification testing.
Demonstration of containment vessel leaktightness was accomplished by installing 1/2 NPT ports through the knuckle region of the OCV and ICV lid torispherical heads to allow evacuation and subsequent backfill of each corresponding containment vessel cavity with helium gas. This method ensured helium gas was present behind each containment seal, thereby validating the testing process. Helium leakage rate testing was also performed on the metallic containment boundaries following testing of the CTU. Helium leakage rate testing of each containment boundary was accomplished by welding each containment component (i.e., lid and body structure) to a flat steel plate. Each containment component was evacuated, tented with helium gas, and helium leakage rate tested to demonstrate containment integrity. Results of successful mass spectrometer helium leakage rate testing are summarized below:
Sealing Component                          OCV                            ICV
                                                  -8                            -8 Main O-ring Seal              <1.0 x 10 cc/s, helium          <1.0 x 10 cc/s, helium Vent Port Plug O-ring Seal        <1.0 x 10-8 cc/s, helium        <1.0 x 10-8 cc/s, helium Lid Structure              3.5 x 10-8 cc/s, helium        <1.0 x 10-8 cc/s, helium Body Structure              4.2 x 10-8 cc/s, helium        1.3 x 10-7 cc/s, helium When accounting for the conversion between air leakage (per ANSI N14.5) and helium leakage, a 2.6 factor applies for standard temperatures and pressures. Thus, a reported helium leakage rate of 1.3 x 10-7 cc/s, helium, is equivalently 5 x 10-8 cc/s, air, a magnitude well below the leaktight criterion of 1 x 10-7 cc/s, air, per ANSI N14.5.
As with the ETU, the ICV wiper O-ring seal ring was damaged somewhat (buckled) in several locations due to failure of several drive screws. Thus, some of the payload drum filler material appeared to be forced into the region above the wiper O-ring seal. Both the damage to the wiper seal ring and presence of residual material in the wiper seal region were identically noted for the TRUPACT-II CTUs. As noted earlier, however, all containment O-ring seals successfully passed subsequent helium leakage rate testing due to the beneficial presence of the foam debris seal, thereby clearly demonstrating that containment integrity was maintained.
In general, damage to the CTU closely paralleled damage to the ETU. The only exception noted was for the OCV vent port region. Visual inspection of the OCV vent port fitting determined that the inner groove weld was cracked approximately 1/3 of its circumferential length. Upon closer visual inspection of the 5/16-inch inner groove weld, the weld size appeared below nominal size, possible due to excessive grinding of welded regions during fabrication. As noted earlier, both the ETU and CTU were fabricated from TRUPACT-II training units, i.e., production units with undersized welds in localized regions where excessive flush grinding sometimes significantly reduced the shell thickness. The only way to determine actual, as-tested, OCV vent port fitting weld sizes would be to section the fitting region, a process that was not performed.
Of significance is that helium leakage rate testing determined that containment integrity was maintained due to the presence of the outer fillet weld. Therefore, although damaged during testing, the OCV vent port region nevertheless remained acceptably leaktight because of the double weld configuration.
2.10.3-40
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 In conclusion, with the aforementioned exception, overall damage to the HalfPACT CTU paralleled the measured damage from both HalfPACT ETU and TRUPACT-II certification testing, as expected.
2.10.3-41
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.10.3-42
 
HalfPACT Safety Analysis Report                                                                            Rev. 9, August 2022 Table 2.10.3 TRUPACT-II / HalfPACT Comparison Using NUREG/CR-3966 Axial, Shear, and Moment Forces at the OCV Locking Ring Impact Angle                        Due to Primary Impact                            Due to Secondary Impact (with respect to horizontal) Axial Force, lb Shear Force, lb Moment, in-lb Axial Force, lb Shear Force, lb Moment, in-lb TRUPACT-II, Primary Impact on OCA Lid 5&#xba;                              121,225          465,347        2.158(10)7          0            471,554      2.186(10)7 10&#xba;                            195,504          372,368        1.727(10)7          0            471,036      2.184(10)7 15&#xba;                            251,344          315,030        1.461(10)7          0            467,404      2.167(10)7 20&#xba; (CTU Test, -20 &#xba;F)          302,679          279,288        1.295(10)7          0            461,178      2.138(10)7 47.7&#xba; (c.g. over corner)        738,279          223,251        1.035(10)7 TRUPACT-II, Primary Impact on OCA Body 5&#xba;                              118,730          455,768        2.113(10)7          0            485,900      2.253(10)7 10&#xba;                            189,342          360,631        1.672(10)7          0            485,275      2.250(10)7 15&#xba;                            244,441          306,378        1.421(10)7          0            480,899      2.230(10)7 18&#xba; (CTU Test, Ambient)        274,975          284,218        1.318(10)7          0            477,148      2.212(10)7 HalfPACT, Primary Impact on OCA Lid 5&#xba;                              115,380            7,431          1.760(10)7          0            4,876        1.157(10)7 10&#xba;                            185,532            5,929          1.407(10)7          0            4,866        1.155(10)7 15&#xba;                            235,898            4,961          1.177(10)7          0            4,822        1.144(10)7 37&#xba; (c.g. over corner)          451,020            3.373          0.800(10)7 HalfPACT, Primary Impact on OCA Body 5&#xba;                              112,409            7,240          1.718 (10)7          0            5,035        1.195(10)7 10&#xba;                            178,914            5,717          1.357 (10)7          0            5,022        1.192(10)7 15&#xba;                            227,810            4,791          1.137 (10)7          0            4,971        1.180(10)7 2.10.3-43
 
HalfPACT Safety Analysis Report                                                                              Rev. 9, August 2022 Table 2.10.3 Summary of HalfPACT ETU Test Results in Sequential Order Test                                                          Orientation        Test No.                  Test Description                                    Temperature    Observations and Results 1  NCT 3' side drop opposite OCV vent port                  0&#xba;    200&#xba;      53 &#xba;F    16"/18" flat at top/bottom; ~3/4" deep 2  HAC 30' side drop opposite OCV vent port                  0&#xba;    200&#xba;      57 &#xba;F    36"/33" flat at top/bottom; ~31/4" deep 3  NCT 3' side drop on OCV vent port                        0&#xba;      0&#xba;        40 &#xba;F    18"/18" flat at top/bottom; ~3/4" deep 4  HAC 30' side drop on OCV vent port                        0&#xba;      0&#xba;        48 &#xba;F    34"/34" flat at top/bottom; ~31/4" deep 5  NCT 3' corner drop between tie-down lugs                43&#xba;    110&#xba;      53 &#xba;F    26" long x 51/2" wide flat; ~1 " deep 6  HAC 30' corner drop between tie-down lugs                43&#xba;    110&#xba;      55 &#xba;F    40" long x 12" wide flat; ~31/4" deep 7  Puncture drop below 3/8-to-1/4-inch transition          20&#xba;    200&#xba;      38 &#xba;F    101/2" long x 111/2" wide hole; ~8" deep 8  Puncture drop on OCV vent port                            1&#xba;      0&#xba;        40 &#xba;F    ~21/2" deep dent 9  Puncture drop on damaged bottom corner                  43&#xba;    110&#xba;      28 &#xba;F    ~3" deep dent 10  Puncture drop above 3/8-to-1/4-inch transition            9&#xba;    290&#xba;      29 &#xba;F    ~51/2" deep dent; ~27" long weld tear 11  Fire with Test 1, 2, & 4 damage at hottest location      0&#xba;    146&#xba;      43 &#xba;F    ~1,575 &#xba;F temperature; ~33 minutes Notes:
Tested 2/18/97 - 3/10/97.
Meridional angle, , is relative to horizontal (i.e., side drop orientation).
Circumferential angle, , is relative to OCV vent port.
2.10.3-44
 
HalfPACT Safety Analysis Report                                                                              Rev. 9, August 2022 Table 2.10.3 Summary of HalfPACT CTU Test Results in Sequential Order Test                                                          Orientation        Test No.                  Test Description Temperature    Observations and Results 1    NCT 3' side drop on OCV vent port                        0&#xba;      0&#xba;        52 &#xba;F    13"/13" flat at top/bottom; ~1/2" deep 2    HAC 30' side drop on OCV vent port                        0&#xba;      0&#xba;        50 &#xba;F    37"/37" flat at top/bottom; ~33/4" deep 3    HAC 30' slapdown drop on OCA lid/tie-down lug            5&#xba;    1471/2&#xba;      41 &#xba;F    411/2" flat at top; ~43/4" deep at top 4    Puncture drop on OCV vent port                          11/2&#xba;      0&#xba;        42 &#xba;F    ~33/4" deep dent 5    Puncture drop above 3/8-to-1/4-inch transition          16&#xba;    250&#xba;      52 &#xba;F    ~4" deep dent; ~23" long weld tear 6    Puncture drop below 3/8-to-1/4-inch transition          23&#xba;    110&#xba;      52 &#xba;F    ~31/2" deep dent (no penetration) 7    Fire with Test 1, 2, & 4 damage at hottest location      0&#xba;    146&#xba;      43 &#xba;F    ~1,485 &#xba;F temperature; ~33 minutes Notes:
Tested 3/16/98 - 4/14/98.
Meridional angle, , is relative to horizontal (i.e., side drop orientation).
Circumferential angle, , is relative to OCV vent port.
2.10.3-45
 
HalfPACT Safety Analysis Report                                                                          Rev. 9, August 2022 Table 2.10.3 Summary of HalfPACT CTU Temperature Indicating Label Readings Temperature Indicating Label Location and Circumferential Angle,                        Label Number    Temperature OCV Conical Shell at 0&#xba; (OCV Vent Port Seal) - Free Drop Tests 1 & 2, and Puncture Drop Test 4    1a, 1b      180 &#xba;F, 170 &#xba;F OCV Conical Shell at 110&#xba; - Puncture Drop Test 6                                                      2            180 &#xba;F OCV Conical Shell at 250&#xba; - Puncture Drop Test 5                                                      3            130 &#xba;F OCV Seal Flange at 0&#xba; (Main OCV Seals) - Free Drop Tests 1 & 2, and Puncture Drop Test 4          4a, 4b      200 &#xba;F, 200 &#xba;F OCV Seal Flange at 110&#xba; (Main OCV Seals) - Puncture Drop Test 6                                      5            200 &#xba;F OCV Seal Flange at 1471/2&#xba; (Main OCV Seals) - Free Drop Test 3                                          6            180 &#xba;F OCV Seal Flange at 250&#xba; (Main OCV Seals) - Puncture Drop Test 5                                      7            140 &#xba;F ICV Seal Flange at 0&#xba; (ICV Vent Port Seal) - Free Drop Tests 1 & 2, and Puncture Drop Test 4          8            105 &#xba;F ICV Seal Flange at 0&#xba; (Main ICV Seals) - Free Drop Tests 1 & 2, and Puncture Drop Test 4              9            105 &#xba;F ICV Seal Flange at 110&#xba; (Main ICV Seals) - Puncture Drop Test 6                                      10            105 &#xba;F ICV Seal Flange at 1471/2&#xba; (Main ICV Seals) - Free Drop Test 3                                        11            110 &#xba;F ICV Seal Flange at 250&#xba; (Main ICV Seals) - Puncture Drop Test 5                                      12            110 &#xba;F 2.10.3-46
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Figure 2.10.3 Drop Pad at the Coyote Canyon Aerial Cable Facility 2.10.3-47
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.10.3-48
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Figure 2.10.3 Design Comparison between a TRUPACT-II Packaging and a HalfPACT Packaging 2.10.3-49
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Figure 2.10.3 Design Comparison between 55-Gallon Drum Payload Assemblies 2.10.3-50
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.10.3 Making the HalfPACT ETU OCA from TRUPACT-II Unit 104 2.10.3-51
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.10.3 Making the HalfPACT ETU OCA from TRUPACT-II Unit 104 2.10.3-52
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.10.3 Making the HalfPACT CTU OCA from TRUPACT-II Unit 107 2.10.3-53
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.10.3 Making the HalfPACT CTU ICV from TRUPACT-II Unit 107 2.10.3-54
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.10.3 Dimensional Comparison of TRUPACT-II and HalfPACT for NUREG/CR-3966 (Lower Figures are Simplifying Representations Used in CASKDROP) 2.10.3-55
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.10.3 Schematic of HalfPACT ETU Test Orientations 2.10.3-56
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 2.10.3 Schematic of HalfPACT CTU Test Orientations 2.10.3-57
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.10.3-58
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 Figure 2.10.3 Schematic of HalfPACT CTU Temperature Indicating Label Location 2.10.3-59
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 This page intentionally left blank.
2.10.3-60
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 ETU Free Drop Test 1; Top-End Damage; ~16" Wide Flat Figure 2.10.3 ETU Free Drop Test 1; Bottom-End Damage; ~18" Wide Flat 2.10.3-61
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 ETU Free Drop Test 2; Top-End Damage; ~36" Wide Flat Figure 2.10.3 ETU Free Drop Test 2; Bottom-End Damage; ~33" Wide Flat 2.10.3-62
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 ETU Free Drop Test 3; View Just Prior to NCT Free Drop Test Figure 2.10.3 ETU Free Drop Test 3; Top-End Damage; ~18" Wide Flat 2.10.3-63
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 ETU Free Drop Test 4; Top-End Damage; ~34" Wide Flat Figure 2.10.3 ETU Free Drop Test 4; Bottom-End Damage; ~34" Wide Flat 2.10.3-64
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 ETU Free Drop Test 5; Bottom Corner Damage; ~26" Wide Flat Figure 2.10.3 ETU Free Drop Test 5; Bottom Corner Damage; ~51/2" Deep Flat 2.10.3-65
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 ETU Free Drop Test 6; Bottom Corner Damage; ~40" Wide Flat Figure 2.10.3 ETU Free Drop Test 6; Bottom Corner Damage; ~12" Deep Flat 2.10.3-66
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 ETU Puncture Drop Test 7; ~101/2" High x ~111/2" Wide Hole Figure 2.10.3 ETU Puncture Drop Test 7; Radial Penetration ~8" Deep 2.10.3-67
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 ETU Puncture Drop Test 8; View of Damage; ~21/2" Deep Dent Figure 2.10.3 ETU Puncture Drop Test 8; Close-up View of Damage; ~21/2" Deep Dent 2.10.3-68
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 ETU Puncture Drop Test 9; View of Impact on Puncture Bar Figure 2.10.3 ETU Puncture Drop Test 9; Bottom Corner Damage; ~3" Deep Dent 2.10.3-69
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 ETU Puncture Drop Test 10; 3/8-to-1/4 Transition; ~27" Long Tear Figure 2.10.3 ETU Puncture Drop Test 10; 3/8-to-1/4 Transition; ~51/2" Deep Dent 2.10.3-70
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 ETU Fire Test 11; Side 1 View Showing Tests 1, 2, 7, & 10 Damage Figure 2.10.3 ETU Fire Test 11; Side 2 View Showing Tests 3, 4, 5, 6, 8, & 9 Damage 2.10.3-71
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 ETU Fire Test 11; Overall View ~5 Minutes after Start of Fire 2.10.3-72
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Figure 2.10.3 ETU Fire Test 11; View ~12 Minutes after Start of Fire Figure 2.10.3 ETU Fire Test 11; View ~25 Minutes after Start of Fire 2.10.3-73
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Figure 2.10.3 ETU Fire Test 11; View ~32 Minutes after Start of Fire Figure 2.10.3 ETU Fire Test 11; View ~17 Minutes after End of Fire 2.10.3-74
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 ETU Fire Test 11; View ~37 Minutes after End of Fire Figure 2.10.3 ETU; View Before Disassembly 2.10.3-75
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 ETU; Removal of the OCA Lid Outer Shell (Note Crumbling Foam Char)
Figure 2.10.3 ETU; Residual Foam in OCA Lid Side; Aligned with Test 1, 2, & 7 Damage 2.10.3-76
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 ETU; Residual Foam in OCA Lid Side; Remote From Test Damage Figure 2.10.3 ETU; Residual Foam in OCA Lid Top (~11")
2.10.3-77
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 ETU; View of OCV Seal Test Port Plug (As Removed; Not Cleaned)
Figure 2.10.3 ETU; View of OCV Vent Port Cover (As Removed; Not Cleaned) 2.10.3-78
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 ETU; View of OCV Vent Port Plug (As Removed; Not Cleaned)
Figure 2.10.3 ETU; View of 55-Gallon Payload Drums Following ICV Lid Removal 2.10.3-79
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Figure 2.10.3 ETU; View of ICV Body Cavity Following Payload Drum Removal Figure 2.10.3 ETU; View of Debris Inside ICV Body Cavity After Payload Drum Removal 2.10.3-80
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU; 5-Inch Thick Payload Spacer (Wood Simulation) in Bottom of ICV Figure 2.10.3 CTU; Aligning 55-Gallon Drum Payload Assembly for Installation into ICV 2.10.3-81
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU; Final ICV Lid Alignment During ICV Lid Installation Figure 2.10.3 CTU; Final OCA Lid Alignment During OCA Lid Installation 2.10.3-82
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Figure 2.10.3 CTU; Certification Test Unit (TRUPACT-II Unit 107) After Final Assembly 2.10.3-83
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Free Drop Test 1; Lid-End Damage; ~13" Wide Flat 2.10.3-84
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 CTU Free Drop Test 1; Bottom-End Damage; ~13" Wide Flat 2.10.3-85
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Free Drop Test 2; Lid-End Damage; ~37 Wide Flat 2.10.3-86
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 CTU Free Drop Test 2; Bottom-End Damage; ~37" Wide Flat 2.10.3-87
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 CTU Free Drop Test 3; Lid-End Damage; ~411/2" Wide Flat 2.10.3-88
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Figure 2.10.3 CTU Free Drop Test 3; Bottom-End Damage 2.10.3-89
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Puncture Drop Test 4; Mounting the Puncture Bar 2.10.3-90
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Puncture Drop Test 4; Close-up View of Damage 2.10.3-91
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU Puncture Drop Test 4; Close-up Profile View of Damage; ~33/4" Deep 2.10.3-92
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Puncture Drop Test 5; Close-up View of Damage 2.10.3-93
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Puncture Drop Test 5; Profile Views of Damage; ~4" Deep 2.10.3-94
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Puncture Drop Test 6; Overall View of Damage 2.10.3-95
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Puncture Drop Test 6; Close-up Views of Damage; ~31/2" Deep 2.10.3-96
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; Side 1 View Before Fire Showing Tests 1, 2, & 4 Damage 2.10.3-97
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; Side 2 View Before Fire Showing Test 5 Damage 2.10.3-98
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; Overall View ~5 Minutes after Start 2.10.3-99
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; View ~10 Minutes after Start 2.10.3-100
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; View ~15 Minutes after Start (Showing Wind Effects) 2.10.3-101
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; View ~28 Minutes after Start (Note Flares at Vents) 2.10.3-102
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; Side 1 View ~33 Minutes after Start (End of Fire) 2.10.3-103
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; Side 2 View ~33 Minutes after Start (End of Fire) 2.10.3-104
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU Fire Test 7; Side 1/2 Views ~10 Minutes after End of Fire 2.10.3-105
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 CTU; View Before Disassembly (OCV Seal Test Port in Foreground) 2.10.3-106
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU; Removal of the OCA Lid Outer Shell (Note Crumbling Foam Char) 2.10.3-107
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 Figure 2.10.3 CTU; Residual Foam in OCA Lid Side; Aligned with Test 1, 2, & 4 Damage Figure 2.10.3 CTU; Residual Foam in OCA Lid Knuckle; Aligned with Test 1, 2, & 4 Damage 2.10.3-108
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU; Residual Foam in OCA Lid Top (~11")
Figure 2.10.3 CTU; Residual Foam in OCA Lid Side; Remote from Test Damage 2.10.3-109
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU; Close-up of OCV Seal Test Port Plug (As Removed/Not Cleaned)
Figure 2.10.3 CTU; OCV Vent Port Region After Removing Excess Foam Char 2.10.3-110
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 CTU; Close-up of OCV Vent Port Cover (As Removed/Not Cleaned)
Figure 2.10.3 CTU; Close-up of OCV Vent Port Plug (As Removed/Not Cleaned) 2.10.3-111
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 CTU; Close-up of Damage to ICV Locking Ring Figure 2.10.3 CTU; End View of OCV Cavity Showing Deformed Lower Seal Flange 2.10.3-112
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Figure 2.10.3 CTU; Residual Foam in OCA Lid Side; Aligned with Test 1, 2, & 4 Damage Figure 2.10.3 CTU; Residual Foam in OCA Body Side; Remote from Test Damage 2.10.3-113
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Figure 2.10.3 CTU; Helium Leakage Rate Testing the ICV Lid Structure Figure 2.10.3 CTU; Helium Leakage Rate Testing the OCV Body Structure 2.10.3-114
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Figure 2.10.3 CTU; Close-up View of Cracked OCV Vent Port Coupling Inner Weld Figure 2.10.3 CTU; Close-up View of Cracked OCV Vent Port Coupling Inner Weld 2.10.3-115
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
2.10.3-116
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 3.0 THERMAL EVALUATION This chapter identifies and describes the principal thermal design aspects of the HalfPACT package.
This chapter further demonstrates the thermal safety of the system and compliance with the thermal requirements of 10 CFR 71 1 when transporting a payload generating a maximum of 30 watts decay heat. Specifically, per 10 CFR &sect;71.43(g), the maximum accessible package surface temperature is shown to be less than 185 &#xba;F during normal conditions of transport (NCT). The bulk temperature of the impact absorbing, polyurethane foam is shown to be less than 160 &#xba;F based on NCT maximum temperature conditions thereby retaining sufficient structural integrity to protect the payload during the subsequent hypothetical accident condition (HAC) drop scenarios described in Chapter 2.0, Structural Evaluation. Finally, the maximum HAC O-ring seal temperature of 290 &#xba;F is sufficiently below the seal material limit to ensure containment and confinement integrity.
All details relating to payloads and payload preparation for shipment in a HalfPACT package are presented in the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) 2.
3.1 Discussion 3.1.1 Packaging The HalfPACT packaging is designed with a totally passive thermal system. As illustrated in Figure 1.1-1 and Figure 1.1-2 from Section 1.1, Introduction, the principal thermal characteristic of the HalfPACT package is that it does not contain the relatively thick steel shells and lead shielding typical of other shipping packages. Instead, the HalfPACT packaging utilizes a relatively thin containment and confinement vessel with shell thicknesses of 1/4 and 3/16 inch, respectively. Use of the thin shells means that the thermal response of the packaging shells to transient heat input is more rapid than for conventional, heavy walled packages. This characteristic is significantly offset by the unusually large, insulating capability of the polyurethane foam tending to isolate, or decouple, interior responses from temperature variations due to exterior transients. The outer surface of these shells may be painted. The analyses herein use unpainted surface (i.e., bare stainless steel) thermal properties. Since painted surfaces have higher emissivities that allow for better decay heat rejection than unpainted surfaces, the use of unpainted surface thermal properties is conservative.
Both the inner containment vessel (ICV) and the outer confinement vessel (OCV) are constructed of Type 304 stainless steel. As discussed in Section 1.2, Package Description, the ICV has a 72-inch inside diameter, and the OCV has a 73-inch inside diameter and is completely encased in polyurethane foam with a density of approximately 81/4 lb/ft3. The foam provides impact protection for the NCT and HAC drop events, and thermal protection during the subsequent HAC thermal event. The 1/4-to-3/8-inch thick outer shell of the outer confinement 1
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
3.1-1
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 assembly (OCA) is comprised of Type 304 stainless steel that serves to protect the polyurethane foam from damage encountered during normal handling and shipping operations.
3.1.2 Payload Configuration As described in Section 1.1, Introduction, the HalfPACT packaging is designed to carry nine different payload configurations. The first payload configuration consists of seven 55-gallon drums arranged on one pallet. The drums are arranged by placing six drums symmetrically around a seventh, center drum. Figure 2.9-3 of the CH-TRAMPAC illustrates the arrangement of the seven, 55-gallon drums. This seven drum configuration represents the bounding thermal case for the HalfPACT package due to the center drum being insulated from the package side wall by six peripheral drums, and due to their smaller relative size, a higher volumetric heat generation than the other payload configurations described below.
Two polyethylene sheets (a molded, bottom slip sheet, and a flat, top reinforcing plate for the set of seven drums) may be used for handling operations (as an option, the bottom slip sheet may be of cardboard). In addition, optional polyethylene plastic wrap may be used to provide greater stability for the payload drums once loaded on the pallet. Calculations show that as many as eighteen layers of the clear-to-translucent plastic wrap (each 0.002 inches thick) may be installed around the outside of the drums without having a significant thermal effect (see Appendix 3.6.2.3, Polyethylene Plastic Wrap Transmittance Calculation). The plastic wrap may also overlap the top of the drums by a few inches. As an option, steel banding straps may be used around the outside of the payload drums instead of the polyethylene stretch wrap to maintain drum stability.
The second payload configuration consists of one 37-inch tall standard waste box (SWB) designed specifically for this type of packaging. Figure 2.9-18 of the CH-TRAMPAC illustrates a SWB assembly. This configuration does not represent a bounding thermal condition due to its relatively large size corresponding to a lower volumetric heat generation rate in comparison to the seven 55-gallon drum payload configuration. Thus, presentation of the SWB evaluation is not explicitly included herein.
The third payload configuration consists of four 85-gallon drums, which range in dimensions to yield 75 to 88 gallons. Figure 2.9-11 of the CH-TRAMPAC illustrates the arrangement of four short 85-gallon drums, which includes the additional payload spacer, and Figure 2.9-12 of the CH-TRAMPAC illustrates the arrangement of four tall 85-gallon drums. As with the 55-gallon drums, both top and bottom polyethylene sheets may be used for handling operations. In addition, the 85-gallon drums may be banded together with either polyethylene plastic wrap or steel banding straps. Similarly, this configuration does not represent a bounding thermal condition since all of the drums are adjacent to the package side wall resulting in cooler payload drum temperatures. Thus, presentation of the 85-gallon drum payload evaluation is not explicitly included herein.
The fourth payload configuration consists of three 100-gallon drums. Figure 2.9-15 of the CH-TRAMPAC illustrates the arrangement of the three 100-gallon drums. As with the 55-gallon drums, both top and bottom polyethylene sheets may be used for handling operations. In addition, the 100-gallon drums may be banded together with either polyethylene plastic wrap or steel banding straps. Similarly, this configuration does not represent a bounding thermal condition since all of the drums are adjacent to the package side wall resulting in cooler payload 3.1-2
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 drum temperatures. Thus, presentation of the 100-gallon drum payload evaluation is not explicitly included herein.
The fifth, sixth, seventh, eighth, and ninth payload configurations consist of the SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2 shielded containers. Figure 2.9-22, Figure 2.9-25, Figure 2.9-27, Figure 2.9-29, and Figure 2.9-31 of the CH-TRAMPAC illustrate the arrangement of the shielded container payloads. Presentation of the shielded container payload evaluations are provided in Appendix 4.5, Appendix 4.7, Appendix 4.8, Appendix 4.9, and Appendix 4.10 of the CH-TRU Payload Appendices.
Based on the wide variety of payloads for the HalfPACT, the analyses presented herein use a bounding thermal payload of 30 thermal watts per package 3 uniformly distributed in one or more payload container(s) combined with a conservatively low payload conductivity commensurate with that of loosely packed paper. Actual payload decay heat is typically far less than 30 watts.
Additionally, high heat payloads typically have correspondingly higher thermal conductivities than loosely packed paper, so a combination of low conductivity with a uniform heat generation will lead to conservatively upper bounded temperature predictions. Two steady-state thermal analysis cases are presented based on decay heat distributions as follows:
: 1. Seven 55-gallon drums with all the decay heat distributed uniformly in all seven drums, and
: 2. Seven 55-gallon drums with all the decay heat distributed uniformly within the center drum.
3.1.3 Boundary Conditions The heat transfer characteristics of the HalfPACT packaging are evaluated for the bounding payload configuration under two thermal boundary conditions. These conditions are:
A. Steady-state conditions at an ambient temperature of 100 &#xba;F, with insolation as defined in 10 CFR &sect;71.71(c)(1), and B. Steady-state conditions at an ambient temperature of -40 &#xba;F, without insolation as described in 10 CFR &sect;71.71(c)(2).
Note that 10 CFR &sect;71.43(g) stipulates that for exclusive use packages, maximum accessible surface temperatures must be less than 185 &#xba;F for a package under 100 &#xba;F ambient conditions without insolation. Package temperatures prior to the start of the HAC thermal event are based on this condition, and are presented in Table 3.5-1 from Section 3.5.3, Package Temperatures.
Maximum steady-state package temperatures with insolation are determined by using a combination of solar heating values. An analysis is made using the insolation values delineated in 10 CFR &sect;71.71(c)(1), averaged over 24 hours. This action is intended to simulate the slow thermal response that the payload and internal package components have to a varying (i.e.,
cyclic) solar load. The relatively large thermal mass on the inside of the polyurethane foam insulation isolates (i.e., decouples) the 12 hour on / 12 hour off solar step function cycle applied to the outside of the foam insulation. Thus, components on the inside of the polyurethane foam use the insolation values of 10 CFR &sect;71.71(c)(1), averaged over 24 hours.
3 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico, Section 5.0, Gas Generation Requirements.
3.1-3
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 In contrast, the outer sections of the polyurethane foam and the OCA outer shell will respond much more quickly to varying external solar loads. As such, the maximum steady-state temperatures of the polyurethane foam and OCA outer shell are estimated using the 10 CFR
&sect;71.71(c)(1) insolation values averaged over 12 hours thereby resulting in a more accurate estimate of the maximum external temperature during the 12 hour on solar cycle. Table 3.1-1 presents results from both analyses, depending on the packaging component being considered.
Package performance and resulting component temperatures, when subjected to the hypothetical accident thermal event as described in 10 CFR &sect;71.73(c)(4), are determined via full scale fire testing of the HalfPACT packaging, and are discussed in Section 3.5, Thermal Evaluation for Hypothetical Accident Conditions.
3.1.4 Analysis Summary The primary heat transfer mechanisms utilized in the thermal analyses are conduction and radiation from component to component within the HalfPACT packaging, and convection and radiation from the exterior of the packaging to the ambient. Due to the relatively close coupling of the bodies within the package, convective heat transfer within the payload cavity is conservatively neglected. As discussed in Section 3.1.2, Payload Configuration, the thermal conductivity of the material inside the drums is conservatively chosen to be that of still air, based on the assumption of loosely packed paper. The following sections present these analyses in greater detail.
In all cases, the steady-state heat transfer analyses are performed using the thermal network analyzer computer program, SINDA85/FLUINT, Version 3.1 4.
Table 3.1-1 presents a summary of the temperatures determined by the steady-state heat transfer analyses for the major components of the HalfPACT packaging for the two bounding payload configurations with the maximum internal decay heat of 30 thermal watts. Temperatures denoted as average use volume-based weighting of the nodal temperatures to determine the average. Further details of these analyses are presented in Section 3.4, Thermal Evaluation for Normal Conditions of Transport.
Discussion of HAC fire testing is provided in Section 3.5, Thermal Evaluation for Hypothetical Accident Conditions. Adjusting for the difference between the calculated initial condition temperatures and actual test temperatures, the maximum containment and confinement seal temperatures are 200 &#xba;F for the ICV seals and 290 &#xba;F for the OCV seals, respectively. All seal temperatures are shown to be well below the 360 &#xba;F temperature limit for short-term exposure (see Appendix 2.10.2, Elastomer O-ring Seal Performance Tests).
4 Systems Improved Numerical Differencing Analyzer and Fluid Integrator (SINDA/FLUINT), Version 3.1, Cullimore and Ring Technologies, Inc., 1996.
3.1-4
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 3.1 NCT Steady-State Temperatures with 30 Watts Decay Heat Load and Insolation; Seven, 55-Gallon Drums Temperature (&#xba;F)
Case 1          Case 2 (Uniform Heat in  (Uniform Heat in Solar  All Seven Drums)    Center Drum    Maximum Location        Loading                          Only)        Allowable Center Drum Centerline
* Maximum            24 hr avg        183.8            340.4          N/A
* Average            24 hr avg        169.5            251.9 Center Drum Wall
* Maximum            24 hr avg        156.9            164.4          2,750
* Average            24 hr avg        156.4            162.7          2,750 Outer Drum Centerline
* Maximum            24 hr avg        181.4            152.9          N/A
* Average            24 hr avg        167.7            152.7 Outer Drum Wall
* Maximum            24 hr avg        156.7            162.0          2,750
* Average            24 hr avg        153.0            152.6          2,750 Average All Drums
* Centerline        24 hr avg        168.0            166.9
* Wall              24 hr avg        153.5            154.0          2,750 ICV Wall
* Maximum            24 hr avg        152.8            153.8          800
* Average            24 hr avg        148.7            147.7          800
* Minimum            24 hr avg        146.3            144.9          800 ICV Air
* Average            24 hr avg        151.1            150.9          N/A ICV Main O-ring Seal
* Maximum            24 hr avg        147.1            145.4      -40 to 225 OCV Wall
* Maximum            24 hr avg        150.1            149.6          800
* Average            24 hr avg        147.0            145.5          800 OCV Main O-ring Seal
* Maximum            24 hr avg        145.5            143.9      -40 to 225 Polyurethane Foam
* Maximum            12 hr avg        155.0            155.0          300
* Average            24 hr avg        128.9            128.4          300 OCA Outer Shell
* Maximum            12 hr avg        155.0            155.0          800 3.1-5
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 Notes for Table 3.1-1:
The temperature limit for the waste material is discussed in Appendix 6.6 of the CH-TRU Payload Appendices.
Temperature limit based on the minimum melting temperature for carbon steel (see Section 3.3, Technical Specifications of Components).
Temperature limit based on the ASME B&PV Code.
Temperature limits based on the allowable long-term temperature range for butyl rubber (see Section 3.3, Technical Specifications of Components).
Temperature limit based on the maximum operating limit for polyurethane foam (see Section 3.3, Technical Specifications of Components).
3.1-6
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 3.2 Summary of Thermal Properties of Materials The HalfPACT packaging is fabricated primarily of Type 304 stainless steel, 6061-T6 aluminum, polyurethane foam, and ceramic fiber paper insulation. The payload containers (i.e., the 55-gallon drums, 85-gallon drums, 100-gallon drums, and SWB) are constructed of carbon steel, and may be painted or galvanized.
The payload is expected to consist of a combination of low decay heat, non-solidified organically-based material, and higher decay heat, solidified organic or inorganically-based material as described in Section 1.2.3, Contents of Packaging, and Section 5.0 of the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) 1. Analyses presented herein assume a thermally conservative (i.e., very low thermal conductivity; analyzed as still air) payload of loosely packed paper with a maximum total decay heat of 30 watts. This assumption combines the low conductivity of a paper-based payload with the highest decay heat load expected from an all-metallic payload to yield the highest and, therefore, the most conservative payload temperatures. For the purposes of the thermal model, the space between the payload containers is conservatively assumed to be still air.
Table 3.2-1 presents the thermal properties used in the heat transfer model and the references from which they are obtained. Properties between the reported values are calculated via linear interpolation by the heat transfer code. The thermal conductivity of the ceramic paper insulation used as a liner between the polyurethane foam and the outer confinement assembly (OCA) inner and outer shell surfaces is 0.0028 Btu/hr-in-&#xba;F. The thermal analysis model ignores the relatively small effect that the ceramic paper insulation would have on the overall conductivity through the package wall. This assumption is valid because the relatively small thickness of the ceramic fiber paper insulation (1/4-inch thick on both the inside and outside shell surfaces) coupled with a thermal conductivity comparable to that of the polyurethane foam (i.e., 0.0028 Btu/hr-in-&#xba;F versus 0.0016 Btu/hr-in-&#xba;F, respectively) tends to minimize the overall effect. Also, using the lower conductivity of the polyurethane foam bounds the temperatures in the NCT steady-state thermal analyses.
Table 3.2-2 presents the material properties for the 3.5 lb/ft3 aluminum honeycomb used in the inner containment vessel (ICV). Due to the orthotropic nature of the honeycomb structure, thermal conductivity varies in both the radial and axial directions. Appendix 3.6.2.2, Aluminum Honeycomb Conductivity Calculation, presents the calculational methodology utilized to determine aluminum honeycomb thermal conductivity based on the honeycomb geometry.
Table 3.2-3 presents the thermal conductivity of air. Because the thermal conductivity of air varies significantly with temperature, the computer model calculates the thermal conductivity across air spaces as a function of the mean film temperature. The void spaces within the ICV, and between the ICV and OCV are conservatively assumed filled with one atmosphere air.
Table 3.2-4 presents the important parameters in radiative heat transfer, emissivity () for each radiating surface and solar absorptivity () value for the exterior surfaces. The outer shell of the OCA conservatively uses the lower value of emissivity ( = 0.25) for the NCT steady-state analyses lower bounding heat transmission in the outward direction thereby conservatively upper 1
U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
3.2-1
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 bounding the package internal temperatures. Optionally painting the OCA outer surface significantly increases the emissivity; therefore, use of the lower value of emissivity of  = 0.25 is conservative 2. Transmittance () of the optional drum polyethylene plastic wrap is discussed in Appendix 3.6.2.3, Polyethylene Plastic Wrap Transmittance Calculation.
Table 3.2 Thermal Properties of Homogenous Materials Thermal Temperature            Conductivity          Specific Heat            Density Material                      (&#xba;F)            (Btu/hr-in-&#xba;F)          (Btu/lb-&#xba;F)            (lb/in3)
                                      -200                  0.516                  0.080 0                  0.633                  0.111 100                  0.675                    ---
200                  0.716                  0.124 Stainless Steel                  400                  0.816                  0.130 0.289 Type 304                      600                  0.916                  0.134 800                  1.000                  0.140 1,000                  1.100                    ---
1,200                  1.200                  0.158 1,600                  1.400                    ---
                                        -40                  2.750                    ---
32                    ---                  0.102 212                  2.750                  0.115 392                  2.520                  0.126 Carbon Steel 572                  2.280                  0.134              0.283 A36 752                  2.040                  0.145 932                  1.820                  0.159 1,112                    ---                  0.179 1,472                  1.820                  0.203 Polyurethane Foam                  ---                  0.0016                  0.300              0.005 Fiberglass Insulation                ---                  0.0019                  0.160                ---
2 Rohsenow, W. M. and J. P. Hartnett, Handbook of Heat Transfer, McGraw-Hill, New York, 1973, Section 15, Table 5. This provides an effective emissivity for painted surfaces from 0.81 for oil based paint on polished iron to 0.95 for enamel based paints. Per Table 3.2-4, the package surface emissivity used in this analysis is 0.25.
3.2-2
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Notes for Table 3.2-1:
Aerospace Structural Metals Handbook, 1989, Metals and Ceramics Information Center, Battelle Memorial Institute, Columbus, Ohio.
Properties of Solids, Thermal Conductivity, Metallic Materials, General Electric, Heat Transfer Division, July 1974.
Thermal conductivity and specific heat for 81/4 pcf polyurethane foam are documented in Section 8.1.4.1.2.1.5, Thermal Conductivity, and Section 8.1.4.1.2.1.6, Specific Heat.
W. M. Rohsenow and J. P. Hartnett, Handbook of Heat Transfer, McGraw-Hill, New York, 1973. Properties for glass wool were used.
Bounding property value used to ensure model stability.
Table 3.2 Thermal Properties of Non-Homogenous Materials Thermal Conductivity            Specific Temperature              (Btu/hr-in-&#xba;F)              Heat        Density Material            (&#xba;F)          Radial            Axial        (Btu/lb-&#xba;F)      (lb/in3)
                          -40          0.053            0.142 Aluminum                68          0.053            0.142 Honeycomb              212            0.055            0.146            0.225        0.002 (3.5 lb/ft3)        752            0.067            0.178 1,500            0.067          0.178 Notes:
Properties of Solids, Thermal Conductivity, Metallic Materials, General Electric, Heat Transfer Division, July 1974.
D. G. Gilmore, Editor, Satellite Thermal Control Handbook, The Aerospace Corporation Press, El Segundo, CA, 1994, ppC-12 to C-16.
Mechanical Properties of Hexcel Honeycomb Materials, TSB-120 (Technical Service Bulletin 120), Hexcel, 1992 (see also Appendix 3.6.2.2, Aluminum Honeycomb Conductivity Calculation).
Bounding property value used to ensure model stability.
3.2-3
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 Table 3.2 Thermal Properties of Air Thermal          Specific Temperature      Conductivity      Heat        Density        Prandtl      Viscosity
(&#xba;F)        (Btu/hr-in-&#xba;F)    (Btu/lb-&#xba;F)      (lb/in3)    Number          (in2/s)
        -99            0.0013          0.239                        0.739        0.01161 81            0.0013            ---                          ---        0.02610 170              ---              ---                        0.697          ---
261              ---            0.242                          ---        0.04015 350              ---              ---                        0.683          ---
441            0.0019          0.246                          ---        0.05875 530              ---              ---                        0.680 621            0.0022          0.251      Use ideal gas                  0.07958 710              ---              ---        law with        0.682 STP density 801            0.0025          0.257      of 4.4(10)-5                  0.10269 890              ---              ---          lb/in3        0.686 981            0.0028          0.262 1,070              ---              ---                        0.692        0.14066 1,161              ---            0.267 1,250              ---              ---                        0.699        0.16771 1,341            0.0033          0.272 1,500            0.0033          0.280                                        ---
1,520              ---              ---                        0.704        0.21483 Notes:
E. R. Eckert, R. M. Drake, Analysis of Heat Mass Transfer, 3rd Edition, McGraw-Hill Publishers, 1972.
Y.S. Touloukian and C.Y. Ho, Editors, Specific Heat - Nonmetallic Liquids and Gases, Thermophysical Properties Research Center Data Series, Volume 6, Purdue University, 1970.
Rohsenow, Hartnett, and Ganic, Handbook of Heat Transfer Fundamentals, 2nd Edition, McGraw-Hill Publishers, 1973.
Bounding property value used to ensure model stability.
3.2-4
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 Table 3.2 Thermal Radiative Properties Material                            Emissivity                  Absorptivity Stainless Steel                            0.25                        0.50 Carbon Steel 0.80                        N/A Aluminum Honeycomb 0.25                        N/A Ambient Environment                            1.00                        N/A Notes:
W. D. Wood, et al., Thermal Radiation Properties of Selected Materials, Volume I, p56. The emissivity of 0.25 is a conservative lower-bound value for clean and smooth stainless steel, leading to conservatively higher temperatures for NCT.
Frank Kreith, Principles of Heat Transfer, 3rd Edition, Intext Press, Inc., 1973, Table 5-2, p237.
A defined surface emissivity is unavailable from the aluminum honeycomb manufacturer.
However, F. F. Gubareff, J. E. Janssen, and R. H. Torborg, Thermal Radiation Properties Survey, Honeywell Research Center, Minneapolis, Minnesota, p23, 1960, gives an emissivity of 0.31 for oxidized aluminum; 0.25 is conservatively used as a bounding value.
3.2-5
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
3.2-6
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 3.3 Technical Specifications of Components The materials used in the HalfPACT packaging that are considered to be temperature sensitive are the butyl O-ring seals and the polyurethane foam.
The butyl rubber O-ring seals are fabricated of Rainier Rubber compound R0405-70 1, or equivalent, per Appendix 2.10.2, Elastomer O-ring Seal Performance Tests. With reference to Appendix 2.10.2, Elastomer O-ring Seal Performance Tests, the butyl rubber O-ring seals have an allowable short-term temperature limit of 360 &#xba;F (up to 8 hours). The allowable long-term temperature range of -40 &#xba;F to 225 &#xba;F is conservatively bounded by data in Figure 2-25 of Parker O-ring Handbook 2 for butyl rubber and by Rainier Rubber Company material data for butyl rubber compound R0405-70. The results summarized in Table 3.4-1 show the O-ring seal temperatures are within these limits.
The minimum operational temperature of polyurethane foam is -20 &#xba;F, since this is the lowest initial temperature at which the packaging must perform. The allowable temperature range for the polyurethane foam during impact loadings is -20 &#xba;F to 300 &#xba;F 3. In addition, temperature excursions to -40 &#xba;F for the foam will not permanently degrade its properties. Foam performance under hypothetical accident condition (HAC) transient conditions is discussed in Section 3.5, Thermal Evaluation for Hypothetical Accident Conditions. Foam strength sensitivity to temperature is addressed in Chapter 2.0, Structural Evaluation.
The ceramic fiber paper, comprised almost entirely (>99%) of Al2O3 and SiO2 in approximately 50/50 proportions, has a maximum use temperature of 2,300 &#xba;F and a melting point of 3,260 &#xba;F.
Like the polyurethane foam, this essentially inert material is not subject to degradation with age when encased within the stainless steel shells of the OCA.
The other primary packaging materials are stainless steel and aluminum. The melting point for each of these materials is 2,600 &#xba;F and 1,100 &#xba;F, respectively. Carbon steel used for the payload containers has a melting temperature of approximately 2,750 &#xba;F. Polyethylene plastic wrap has a melting temperature of approximately 250 &#xba;F. Loss of the plastic wrap is of no consequence to the safety of the HalfPACT package since its effect on conductive and radiative heat transfer is negligible, as discussed in Appendix 3.6.2.3, Polyethylene Plastic Wrap Transmittance Calculation. Similarly, the loss of items such as foam rubber padding or plastic sheets have negligible impact on the package thermal performance.
1 Rainier Rubber Company, Seattle, WA.
2 ORD 5700, Parker O-ring Handbook, Parker Hannifin Corporation, Cleveland, OH. The Parker O-ring Handbook is available at http://www.parker.com/literature/ORD%205700%20Parker_O-Ring_Handbook.pdf.
3 General Plastics, LAST-A-FOAM FR-3700 for Crash and Fire Protection of Nuclear Material Shipping Containers, General Plastics Manufacturing Company, 4910 Burlington Way, Tacoma, Washington, February 1990.
3.3-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
3.3-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 3.4 Thermal Evaluation for Normal Conditions of Transport This section presents the steady-state thermal analyses of the HalfPACT package for normal conditions of transport (NCT). Under NCT, the package is mounted in an upright position on its transport trailer or railcar. This establishes the orientation of the exterior surfaces of the package for determining the free convection heat transfer coefficients and insolation loading. In addition, the bottom of the dedicated transport trailer is open to free air. Thus, the bottom of the HalfPACT package would be exposed to ambient air instead of resting on the ground or some other semi-adiabatic, conducting surface.
The thermal conditions that are considered for NCT are those specified in 10 CFR &sect;71.71(c)(1) 1.
Accordingly, a 100 &#xba;F ambient temperature with the following insolation values are used for heat input to the exterior package surfaces. Note that the flat base of the package has no insolation; all other surfaces, since they are curved, have an insolation value of 400 gcal/cm2 (10.24 Btu/in2).
Total Insolation for a 12-Hour Period Form and Location of Surface                          (gcal/cm2)                    (Btu/in2)
Flat surfaces transported horizontally:
* Base                                                      None                          none
* Other surfaces                                              800                          20.49 Flat surfaces not transported horizontally                      200                            5.12 Curved surfaces                                                400                          10.24 3.4.1 Thermal Model 3.4.1.1      Analytical Model Figure 3.4-1 and Figure 3.4-2 illustrate the location of the thermal nodes used in the analytical model of the HalfPACT packaging and the 55-gallon drum payload configuration, respectively.
The location and the number of thermal nodes are chosen to achieve an accurate determination of the temperature distribution within the major package components.
The analysis model was constructed using SINDA/FLUINT, Version 3.1 2, and utilizes the thermal properties presented in Section 3.2, Summary of Thermal Properties of Materials. To enhance the accuracy of the model, the material properties of the package steel and aluminum, as well as the air within the package cavity, are computed as a function of temperature. In the case of the polyurethane foam, material properties change little over the NCT temperature range of interest; therefore, constant thermal property values are used.
1 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 Systems Improved Numerical Differencing Analyzer and Fluid Integrator (SINDA/FLUINT), Version 3.1, Cullimore and Ring Technologies, Inc., 1996.
3.4-1
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 The thermal model represents a two-dimensional axisymmetric model of the packaging and its payload. The bounding payload, described in Section 3.1.2, Payload Configuration, consists of a uniform payload of low conductivity and uniform heat distribution. Sensitivity studies have shown that, with a total decay heat load of 30 watts, the placement of the payload within the HalfPACT packaging cavity has a negligible effect on component maximum temperatures.
As seen from Figure 3.4-1, a two-dimensional, axisymmetric model consisting of just under 100 nodes is used to represent the HalfPACT packaging. Increased resolution is utilized in the outer confinement vessel (OCV) and inner containment vessel (ICV) sealing regions to enhance the accuracy of seal temperature predictions.
Figure 3.4-2 illustrates the thermal model used for the 55-gallon drum payload configuration. To account for the non-symmetric effects that occur within the drum-based payload configuration, a quasi-three-dimensional model (i.e., a three-dimensional model with symmetry planes along adiabatic boundaries) of the drums is used. Using the quasi-three-dimensional model with the drum-based payload configuration provides a simplified, yet accurate representation of the packaging as each analysis assumes the heat is either uniformly distributed in all seven drums or in the center drum. The configuration with seven 55-gallon drums with all the decay heat in the center drum represents the bounding case. This is because this particular payload configuration has the highest heat concentration within a single drum and six surrounding drums adding an additional insulating barrier. Therefore, the SWB, four 85-gallon drum, and three 100-gallon drum payload configurations, although evaluated, are not specifically included herein.
Heat transfer across air gaps is calculated using a combination of conduction and radiation heat transfer. Since any offset of the ICV within OCV would be relatively small, and would tend to decrease the net thermal resistance across the shells, the ICV and OCV are assumed to be concentric cylinders. Thus, the air gaps separating the side and top of these components are assumed to be uniform with no contacting surfaces. The bottom ICV/OCV interface is separated by a 1/8-inch thick rubber pad. To maximize the insulating properties of this interface, the pad is assumed to behave as a layer of still air without radiative heat transfer (air conduction only).
The bounding payload configuration is assumed loaded in the ICV cavity with uniform and symmetrical separation from the ICV walls. Again, any eccentricity in the placement of the payload in the package would result in reduced thermal resistance between the payload and cask. Due to the relatively low decay heat load and the narrowness of most gaps and the blockage provided by the pallets, stretch wrap, etc., the model also assumes that no significant internal natural convection paths exist. Free convection of decay heat and solar radiation from the exterior surfaces of the package is computed as a function of temperature and orientation of the surface using standard equations for free convection from vertical and horizontal surfaces. Methodology for calculating convection coefficients is presented in Appendix 3.6.2.1, Convection Coefficient Calculation.
The optional polyethylene plastic wrap around the payload drums has a small effect on the radiative heat transfer between the drums and the ICV wall. As discussed in Appendix 3.6.2.3, Polyethylene Plastic Wrap Transmittance Calculation, the interaction of the plastic wrap with regard to the heat transfer process is determined to have a negligible effect and, therefore, is ignored.
3.4-2
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 3.4.1.2      Test Model This section is not applicable since NCT thermal tests are not performed for the HalfPACT package.
3.4.2 Maximum Temperatures The maximum temperatures for NCT hot conditions (i.e., 100 &#xba;F ambient temperature and insolation per 10 CFR &sect;71.71(c)(1)) and 30 watts decay heat are reported in Table 3.4-1 for the major components of the HalfPACT package. Average drum wall temperatures, ICV wall temperatures, and ICV air temperatures are determined using the area-weighted nodal temperatures. A complete listing of nodal temperatures for the evaluated cases is also provided in the Appendix 3.6.1, Computer Analysis Results.
3.4.3      Minimum Temperatures The minimum temperature distribution for the HalfPACT packaging occurs with a zero decay heat load and an ambient air temperature of -40 &#xba;F per 10 CFR &sect;71.71(c)(2). Since the steady-state analysis of this condition represents a trivial case, no thermal calculations are performed.
Instead, it is assumed that all package components achieve the -40 &#xba;F temperature under steady-state conditions. As discussed in Section 3.3, Technical Specifications of Components, the -40 &#xba;F temperature is within the allowable range of all HalfPACT packaging components. As a potential initial condition for all normal or accident events, a minimum uniform temperature of
-20 &#xba;F must be considered per 10 CFR &sect;71.71(b) and &sect;71.73(b). Detailed structural analyses considering the effects of minimum temperatures are presented in Section 2.6.2, Cold.
3.4.4 Maximum Internal Pressure The evaluation of the maximum internal pressure for the HalfPACT packaging considers the factors that affect pressure to demonstrate that the pressure increases are below the allowable pressure for the package.
3.4.4.1      Design Pressure The HalfPACT packaging has a design pressure of 50 psig. Chapter 2.0, Structural Evaluation, discusses the ability of the package to withstand 50 psig for both normal conditions of transport and hypothetical accident conditions. The ICV or both the OCV and ICV were pressurized to 50 psig in many of the full-scale tests for hypothetical accident conditions as described in Appendix 2.10.3, Certification Tests. The maximum normal operating pressure (MNOP) is discussed in Section 3.4.4.3, Maximum Normal Operating Pressure.
3.4.4.2      Maximum Pressure for Normal Conditions of Transport The maximum pressure in the ICV under normal conditions of transport is less than the 50 psig design pressure, as shown by the following analysis. The major factors affecting the ICV internal pressure are radiolytic gas generation, thermal expansion of gases, and the vapor pressure of water within the ICV cavity. Barometric changes that affect the external pressure, and hence the gauge pressure of the HalfPACT packaging containment and confinement vessels, are bounded by the regulatory condition of a 3.5 psia external pressure and considered in the use of the 50 psig pressure increase limit. ICV internal pressure would not increase significantly due 3.4-3
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 to chemical reactions, biological gas generation, or thermal decomposition in the payload. For the payload shipping categories qualified for transport by gas generation testing, the maximum pressure increase allowed in the ICV for normal conditions is the 50 psig pressure increase limit.
The maximum pressure in the ICV for all categories is calculated for the maximum shipping period of 60 days. The use of a 60-day shipping period in the calculation of maximum normal operating pressure is consistent with 10 CFR 71.41(c). As specified by 10 CFR 71.41(c), this section shows that the controls proposed to be exercised by the shipper are demonstrated to be adequate to provide equivalent safety of the shipment. The use of this shipping period is consistent with the analysis presented in Appendix 3.4 of the CH-TRU Payload Appendices 3, which shows that the maximum normal shipping period will be less than 60 days by a large margin of safety. As described in Appendix 3.4 of the CH-TRU Payload Appendices, routine monitoring of shipments includes the use of the TRANSCOM system at the Waste Isolation Pilot Plant, which provides continuous tracking of shipments from the shipping site to its destination.
Calculation of maximum pressure in the ICV for all categories considers immediate release of gases from the innermost layer of confinement around the waste to the available void volume of the ICV cavity. The available void volume for accumulation of gas in the ICV is conservatively estimated. The available ICV void volume is the ICV void volume less the volume occupied by the payload assembly. The ICV void volume is the internal volume within the ICV containment boundary less the volume occupied by the materials of construction of the end spacers. Since the end spacers were purposely designed to use perforated aluminum honeycomb, each has a large void volume for gas accumulation.
The volume occupied by the payload assembly is the volume of the payload containers plus the volume occupied by the pallet, slipsheets, reinforcing plates, and guide tubes, if applicable. The estimate of the void volume of the ICV considers only the volume in the ICV outside of the payload containers with no credit for the void volume present within the payload containers except for SWBs overpacking four 55-gallon drums. Since drum payload containers have a significant void volume that has historically averaged over 50% of the internal volume, neglecting the void volume in the payload containers will overestimate the pressure increase in the ICV.
The void volume between the SWB and four overpacked 55-gallon drums is included in the ICV volume for pressure analyses because this SWB overpack configuration is not sealed and the internal void volume is quantifiable. The external volume of a single, steel 55-gallon drum can be calculated based on its internal dimensions, tare weight, and the density of steel as follows:
W  0.01639 liters Vdrum =  x D 2 x H +  x 4                    inches 3 3
U.S. Department of Energy (DOE), CH-TRU Payload Appendices, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
3.4-4
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 where:
D = Internal diameter of a 55-gallon drum (cubic inches)
H = Internal height of a 55-gallon drum (cubic inches)
W = Tare weight (empty) of a 55-gallon drum (pounds)
    = Density of steel (pounds per cubic inch)
Therefore, the external volume of a 55-gallon drum is:
60  0.01639 liters Vdrum =  x 22.5 2 x 33.25 +          x                = 220 liters 4                    0.285      inches 3 As shown in Appendix 2.4 of the CH-TRU Payload Appendices, the internal void volume of an empty SWB is conservatively taken as 1,750 liters. Subtracting the volume of four overpacked 55-gallon drums from the empty SWB void volume results in an internal void volume of approximately 870 liters per SWB overpack.
The net void volume in the ICV is assumed filled with air at 70 &#xba;F and 14.7 psia when the ICV is sealed for transport. Sufficient water is assumed present for saturated water vapor at any temperature. The pressure increase due to water vapor is obtained from the tabulated thermodynamic properties of saturated water and steam.
The maximum pressure increase analysis for HalfPACT payloads can be categorized as follows:
* Analytical category payloads have decay heat limits based on conservative theoretical analyses of flammable gas generation as shown in Section 5.0 of the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) 4. These limits are lower than applicable limits for test category wastes and the pressure increase for all analytical category payloads is bound by the test category payloads.
* Test category payloads for which the MNOP can be shown to be below the design pressure by analysis. This analysis is presented in Section 3.4.4.2.1, MNOP Determination by Analysis.
* Test category payloads for which the MNOP is limited to the design pressure and compliance is shown by measurement. Derivation of gas generation rates for these cases in compliance with the pressure limit is presented in Section 3.4.4.2.2, MNOP Determination by Measurement.
In addition, the following conditions govern the pressure analysis for HalfPACT package payloads:
* Waste Material Types I.2, I.3, II.3, III.2, and III.3 have lower G values compared to Waste Material Types I.1, II.1, and III.1, respectively, and will therefore have lower pressure increases.
* The case of the decay heat uniformly distributed in all containers in a payload (versus all decay heat in one container) results in the lowest void volume and bounds the pressure 4
U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
3.4-5
 
HalfPACT Safety Analysis Report                                                                  Rev. 9, August 2022 increase calculations (Note that to meet flammable gas generation requirements, the decay heat in a HalfPACT with a single drum will be less than the decay heat in a HalfPACT with 7 drums.)
* The normal condition, steady state temperatures for decay heat values from 0 to 40 watts for SWBs in the TRUPACT-II bound the steady state temperatures for HalfPACT payload configurations with decay heat values from 0 to 20 watts. This relationship was derived from the temperature profile for 55-gallon drum payload assemblies in the TRUPACT-II and the HalfPACT where the temperature at 20 watts in the HalfPACT is less than the temperature at 40 watts in the TRUPACT-II.
3.4.4.2.1      MNOP Determination by Analysis The method used to calculate the maximum ICV pressure is provided below for an example payload shipping category. The number of moles per second of total gas generated by radiolysis is calculated from the following equation:
n gen = G eff ( T ) x W x C where ngen is the rate of radiolytic gas generation (moles/sec), Geff(T) is the temperature-corrected effective G value (the total number of molecules of gas generated per 100 eV of energy emitted (molecules/100 eV) at the temperature of the target material), W is the total decay heat (watts), and the conversion constant for the units used is C = 1.04(10)-5 (g-moles)(eV)/(molecule)(watt-sec).
The effective G values are provided in Appendix 3.2 of the CH-TRU Payload Appendices for the payload shipping categories. The maximum decay heat for each category determines the average contents temperature for that category. As discussed in Appendix 3.2 of the CH-TRU Payload Appendices, the effective G values provided at room temperature (RT) are a function of temperature based on the activation energy (Ea) for the material. The effective G values used in the calculation for pressure increase in the ICV are corrected to the average contents temperature for each category using the activation energy of the material in the category that is provided in Appendix 3.2 of the CH-TRU Payload Appendices.
For example, the effective G value (total gas) at room temperature for Waste Material Type I.1 is 2.4 (from Appendix 3.2 of the CH-TRU Payload Appendices). The temperature-corrected effective G value is calculated using the following equation:
Ea  T  TRT R    ( T )( TRT )
G ( Total , T) = G ( Total , RT) e where G(Total, RT) is the effective G value at room temperature (the number of molecules of gas generated per 100 eV of energy (molecules/100 eV) for target material at room temperature), Ea is the activation energy for the target material, kcal/g-mole, the ideal gas constant R = 1.99(10)-3 kcal/g-mole-K, T is the temperature of the target material (the average contents temperature),
and the room temperature is TRT = 25 &#xba;C = 298 K.
The temperature-corrected effective G value for Waste Material Type I.1 is calculated at the average contents temperature based on the maximum decay heat for that waste material type. Table 3.4-2 provides the summary of normal condition, steady state temperatures for decay heat values from 0 to 30 watts for package temperatures of interest including average contents temperatures. From Table 3.4-2, the average contents temperature for a total payload decay heat of 30 watts is 169.5 &#xba;F. From 3.4-6
 
HalfPACT Safety Analysis Report                                                                            Rev. 9, August 2022 Appendix 3.2 of the CH-TRU Payload Appendices, the activation energy is zero (Ea = 0) for water, which is the target material. The temperature corrected effective G-value is:
0 kcal/g - mole          349.5 K  298 K 1.99(10) -3 kcal/g - mole - K  (349.5 K)(298 K)
G (eff, 169.5  F) = (2.4 molecules/100 eV)e                                                     
                                    = 2.4 molecules/100 eV Using this temperature-corrected effective G value, the radiolytic gas generation rate, ngen, is:
n gen = (2.4 molecules/100 eV)(30 watts)[1.04(10) 5 (g - moles)(eV)/(molecule)(watt - sec)]
          = 7.49(10)- 6 moles/sec The total number of liters of radiolytic gases that is generated, VR, when corrected from moles to liters at STP (32 &#xba;F and 1 atmosphere pressure) after 60 days would be:
VR = [n gen ](60 days){conversion factors}
              = [7.49(10)- 6 ](60){(86,400 sec/day)(22.4 liters/mole )} = 869.75 liters @ STP The generated volume of radiolytic gases (corrected to STP) is heated to the average ICV gas temperature for normal conditions of transport. The average ICV gas temperature is also available from the HalfPACT package temperatures given in Table 3.4-2. For Waste Material Type I.1, the average gas temperature is 151.1 &#xba;F. The radiolytic gas would occupy a volume, Vrg of:
151.1 &deg;F + 460 &deg;R Vrg = (869.75)                            = 1,080.29 liters @ 151.1 &deg;F 32 &deg;F + 460 &deg;R For a payload of seven 55-gallon drums and an available void volume in the ICV of 1,846 liters, this gas contributes a pressure, prg, of:
1,080.29 p rg =            = 0.59 atm (8.67 psia) @ 151.1 &deg;F 1,846 The initial volume of gas present in the ICV at 70 &#xba;F and 14.7 psia is also heated to 151.1 &#xba;F for a decay heat of 30 watts. The increased pressure associated with this heat-up, phu, is:
151.1 &deg;F + 460 &deg;R p hu = (14.7 psia )                          = 16.95 psia 70 &deg;F + 460 &deg;R The water vapor pressure is based on the temperature of the coolest or condensing surface of the ICV. From Table 3.4-2, the minimum ICV wall temperature is 146.3 &#xba;F for a decay heat of 30 watts. The corresponding water vapor pressure, pwv, at this temperature is 3.39 psia.
The maximum ICV pressure after 60 days for Waste Material Type I.1, pmax, is the sum of the three pressure components less an assumed atmospheric pressure, pa, of 14.7 psia, or:
pmax = prg + phu + pwv - pa = 8.67 psia + 16.95 psia + 3.39 psia - 14.7 psia = 14.32 psig After 60 days, the maximum ICV pressure would be 14.32 psig for a payload of seven 55-gallon drums of Waste Material Type I.1 with a total payload decay heat of 30 watts. Thus, the 3.4-7
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 pressure increase for any such payload with a decay heat less than 30 watts is below the allowable pressure increase limit of 50 psig.
Waste Material Types I.2 and I.3 have lower G values and will therefore have lower total gas generation rates. This means that the pressure increase will be lower than that of Waste Material Type I.1. Hence, the pressure increase for Waste Material Type I.1 is the bounding value for Waste Type I. Similar logic applies for Waste Types II and III and hence Table 3.4-3 provides pressure increase values for Waste Material Types I.1, II.1 and III.1 only. In addition to the above-stated decay heat limit for a payload of seven 55-gallon drums for Waste Type I, compliance with the 50 psig pressure limit can be demonstrated for other container types and Waste Material Types as shown in Table 3.4-3 through Table 3.4-13. Maximum allowable decay heat limits for analytical shipping categories are below the associated test category values shown in Table 3.4-3 through Table 3.4-13, and will therefore have lower pressure increase values.
For all payloads satisfying the applicable container decay heat limits specified in Table 3.4-3 through Table 3.4-13, there is no need to perform total gas generation testing to determine compliance with the 50 psig pressure limit.
For cases where the wattage limits specified in Table 3.4-3 through Table 3.4-13 are exceeded but the packaging design limit of 30 watts per HalfPACT is met, compliance with the container flammable gas generation can be used to evaluate compliance with the total gas generation rate limit. Because the primary mechanism for gas generation for both flammable and total gas for Waste Types I, II, and III is radiolysis, compliance with the flammable gas generation rate limit implies actual G values (both flammable and total) that are much lower than those used to derive the limits in Table 3.4-3 through Table 3.4-13. Therefore, as described in Section 5.2.5.3.3 of the CH-TRAMPAC, compliance with the flammable gas generation rate limits will ensure compliance with the total gas generation rate limits for these cases (e.g., SWBs of Waste Type III greater than 17 watts). Note that, as shown below, Waste Type IV containers compliance with the total gas generation rate limit will be evaluated by measurement.
3.4.4.2.2      MNOP Determination by Measurement For all containers of Waste Type IV, the total gas generation rate must be measured by testing and shown to comply with the applicable limits as described below. (Note: Payloads must also comply with the HalfPACT decay heat limit of 30 watts.)
For containers requiring total gas generation testing as specified above, the allowable number of moles per second of gases (excluding water vapor) released may not exceed a specified limit (see Table 5.2-11, Section 5.2.5 of the CH-TRAMPAC). The calculation is based on the maximum decay heat for each test category. This decay heat provides the minimum ICV wall temperature for determining the vapor pressure of water, and the average ICV gas temperature for determining the pressure rise due to heating the gases initially present when the ICV is sealed. Assuming that atmospheric pressure is 14.7 psia, the allowable absolute pressure in the ICV, pabs, is:
pabs = 50 psig + 14.7 psia = 64.7 psia This absolute pressure is decreased by the water vapor pressure and the increased pressure of the gas initially present in the ICV.
3.4-8
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 The maximum gas release rate in moles/sec per payload container for containers subjected to total gas generation testing is provided in Section 5.2.5 of the CH-TRAMPAC. The method used to calculate the maximum gas release rate is provided below with an example for Waste Type IV.
The maximum decay heat for Waste Type IV in 55-gallon drums is 7 watts (see Section 5.2.5 of the CH-TRAMPAC). Interpolating from the data in Table 3.4-2, the minimum ICV wall temperature is 122.6 &#xba;F and the average ICV gas temperature is 123.4 &#xba;F. The corresponding water vapor pressure at the ICV wall temperature is 1.82 psia. The increased pressure of the ICV gas initially present (assuming air at 70 &#xba;F and 14.7 psia), pini, is then:
123.4 &deg;F + 460 &deg;R pini = (14.7 psia )                    = 16.2 psia 70 &deg;F + 460 &deg;R The allowable absolute pressure in the ICV available for accumulation of gas released from the payload containers, pall, is:
pall = 64.7 psia - 1.82 psia - 16.2 psia = 46.7 psia (3.18 atm)
For a payload of seven 55-gallon drums and an available void volume in the ICV of 1,846 liters, the amount of gas that may be released from the payload containers at 123.4 &#xba;F, Vg, is:
Vg = (3.18 atm)(1,846 liters) = 5,870 liters @ 123.4 &deg;F and 1 atm pressure Thus, the number of moles per second at STP allowed for 60 days from all seven (7) 55-gallon drums for Waste Type IV, ng, is:
32 &deg;F + 460 &deg;R  1 mole  1  1 day n g = (5,870 liters) 123.4 &deg;F + 460 &deg;R  22.4 liters  60 days  86,400 sec
                  = 4.26(10) 5 moles/sec The number of moles/sec per 55-gallon drum, np, would be:
4.26(10) 5 moles/sec np =                            = 6.09(10) 6 moles/sec per drum 7 drums The maximum allowable gas release rate for 60 days for 55-gallon drums from Waste Type IV is 6.09(10)-6 moles/sec per payload container. However, the applicable TRUPACT-II limit of 3.97(10)-6 (lower limit of the two packages) is used to qualify payload containers for either package. The limit for moles/sec per payload container for Waste Type IV is provided in Section 5.2.5 of the CH-TRAMPAC.
Compliance with these limits will be evaluated for 55-gallon drums of Waste Type IV less than or equal to a decay heat of 7 watts per payload container and per HalfPACT and for other payload containers of Waste Type IV less than or equal to a decay heat of 3.5 watts per payload container and per HalfPACT.
The maximum allowable gas release rates provided ensure that the maximum pressure increase in 60 days under normal conditions of transport will not exceed the 50 psig design limit.
The maximum allowable internal pressure in the OCV is also 50 psig. The OCV would only experience significant internal pressure if the ICV had such a pressure and the gases were free to communicate with the OCV. In this case, the maximum internal pressure is 50 psig in the ICV and the additional void volume in the OCV would result in a maximum pressure in the OCV of less than 50 psig.
3.4-9
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 3.4.4.3      Maximum Normal Operating Pressure The HalfPACT package was designed to withstand 50 psig of internal pressure to accommodate the transport of payload materials with the potential to generate gases and increase pressure within the ICV. For the analytical payload shipping categories, the pressure increase in 60 days is less than that for test category waste due to the decay heat limits imposed on analytical category waste. Therefore, the MNOP for the ICV for the analytical categories is not the limiting MNOP for the ICV since a higher value is established by the test payload shipping categories. As discussed in Section 3.4.4.2, Maximum Pressure for Normal Conditions of Transport, the maximum pressure increase in the ICV in 60 days for a test category is allowed to be 50 psig. Since the ICV pressure is allowed to increase to the design pressure of 50 psig, the MNOP for the ICV in the HalfPACT package is 50 psig.
The MNOP for the OCV is low and the pressure increase is due to the temperature increase of the air in the OCV cavity and the vapor pressure of water within the OCV cavity when the HalfPACT package reaches the maximum normal operating temperature. Per Table 3.4-1, the normal condition steady state temperature of the ICV and OCV walls with 30 watts of decay heat is less than 154 &#xba;F. Conservatively assuming that the initial volume of gas present in the OCV at 70 &#xba;F and 14.7 psia is heated to 154 &#xba;F, the increased pressure associated with this heat-up, phu, is:
154 &deg;F + 460 &deg;R p hu = (14.7 psia )                  = 17.03 psia 70 &deg;F + 460 &deg;R Also, conservatively assuming a condensing OCV surface temperature of 154 &#xba;F, the water vapor pressure, pwv, at this temperature is 4.10 psia.
Thus, for normal conditions of transport, the MNOP for the OCV is the sum of the two pressure components less an assumed atmospheric pressure, pa, of 14.7 psia, or:
pmax = phu + pwv - pa = 17.03 psia + 4.10 psia - 14.7 psia = 6.43 psig The design pressure for the OCV is the same as that for the ICV or 50 psig and ensures pressure retention by the OCV in a non-normal situation in which the ICV cavity communicates with the OCV cavity.
3.4.5 Maximum Thermal Stresses Maximum thermal stresses for NCT are determined using the temperature results from Section 3.4.2, Maximum Temperatures, and Section 3.4.3, Minimum Temperatures. NCT thermal stresses are discussed in Section 2.6.1, Heat, and Section 2.6.2, Cold. Corresponding structural analyses utilize a minimum temperature of -40 &#xba;F (-20 &#xba;F when combined with any other load cases), and a maximum temperature of 170 &#xba;F for any HalfPACT packaging component.
3.4-10
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 3.4.6 Evaluation of Package Performance for Normal Conditions of Transport The component temperatures and the internal decay heat distributions presented in Section 3.4.2, Maximum Temperatures, and Section 3.4.3, Minimum Temperatures, are all within the allowable limits for the materials of construction delineated in Section 3.3, Technical Specifications of Components.
3.4-11
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 3.4 NCT Steady-State Temperatures with 30 Watts Decay Heat Load and Insolation; Seven 55-Gallon Drums Temperature (&#xba;F)
Case 1          Case 2 (Uniform Heat in  (Uniform Heat in Solar  All Seven Drums)    Center Drum    Maximum Location        Loading                          Only)        Allowable Center Drum Centerline
* Maximum            24 hr avg        183.8            340.4          N/A
* Average            24 hr avg        169.5            251.9 Center Drum Wall
* Maximum            24 hr avg        156.9            164.4          2,750
* Average            24 hr avg        156.4            162.7          2,750 Outer Drum Centerline
* Maximum            24 hr avg        181.4            152.9          N/A
* Average            24 hr avg        167.7            152.7 Outer Drum Wall
* Maximum            24 hr avg        156.7            162.0          2,750
* Average            24 hr avg        153.0            152.6          2,750 Average All Drums
* Centerline        24 hr avg        168.0            166.9
* Wall              24 hr avg        153.5            154.0          2,750 ICV Wall
* Maximum            24 hr avg        152.8            153.8          800
* Average            24 hr avg        148.7            147.7          800
* Minimum            24 hr avg        146.3            144.9          800 ICV Air
* Average            24 hr avg        151.1            150.9          N/A ICV Main O-ring Seal
* Maximum            24 hr avg        147.1            145.4      -40 to 225 OCV Wall
* Maximum            24 hr avg        150.1            149.6          800
* Average            24 hr avg        147.0            145.5          800 OCV Main O-ring Seal
* Maximum            24 hr avg        145.5            143.9      -40 to 225 Polyurethane Foam
* Maximum            12 hr avg        155.0            155.0          300
* Average            24 hr avg        128.9            128.4          300 OCA Outer Shell
* Maximum            12 hr avg        155.0            155.0          800 3.4-12
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 Notes for Table 3.4-1:
The temperature limit for the waste material is discussed in Appendix 6.6 of the CH-TRU Payload Appendices.
Temperature limit based on the minimum melting temperature for carbon steel (see Section 3.3, Technical Specifications of Components).
Temperature limit based on the ASME B&PV Code.
Temperature limits based on the allowable long-term temperature range for butyl rubber (see Section 3.3, Technical Specifications of Components).
Temperature limit based on the maximum operating limit for polyurethane foam (see Section 3.3, Technical Specifications of Components).
Table 3.4 Summary of Temperatures for Determining MNOP for the ICV Temperature (&#xba;F) with Internal Decay Heat (watts)
Location                        0            10        20          30 Case 1 - Seven 55-Gallon Drums, Uniform Decay Heat in All Seven Drums Average Center Drum Centerline            115.2        133.1      151.2        169.5 Average ICV Air                    115.2        126.9      140.4        151.1 Minimum ICV Wall                    115.2        125.8      135.8        146.3 Case 2 - Seven 55-Gallon Drums, Uniform Decay Heat in Center Drum Only Average Center Drum Centerline            115.2        163.9      209.5        251.9 Average ICV Air                    115.2        127.4      139.5        150.9 Minimum ICV Wall                    115.2        125.8      135.7        144.9 3.4-13
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
3.4-14
 
HalfPACT Safety Analysis Report                                                                                                                                    Rev. 9, August 2022 Table 3.4 HalfPACT Pressure Increase with a 7-Drum Payload, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents        Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material  Drum      Package Temperature        Value, Geff      Energy        Value, Geff      Rate        STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type    (watts)    (watts)    (&deg;F)      (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)      (&deg;F)    (psia)    (psig)
I.1    4.2857      30.00      169.5            2.4              0            2.4        7.49(10)-6      869.75        151.1          8.67        16.95    146.3      3.39    14.32 II.1    4.2857      30.00      169.5            1.7              0.8            2.1        6.47(10)-6      751.31        151.1          7.50        16.95    146.3      3.39    13.14 III.1    3.8571      27.00      164.0            8.4              2.1          13.8        3.87(10)  -5 4496.23        147.9        44.25        16.86    143.2      3.13    49.54
* void volume in the HalfPACT with 7 55-gallon drums is 1,846 liters Table 3.4 HalfPACT Pressure Increase with a 1 SWB Payload, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents        Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material  SWB      Package Temperature        Value, Geff      Energy        Value, Geff      Rate        STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type    (watts)    (watts)    (&deg;F)      (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)      (&deg;F)    (psia)    (psig)
I.1    20.0000      20.00      238.0            2.4              0            2.4        4.99(10)-6      579.45        148.0          7.06        16.86    144.0      3.20    12.42 II.1  20.0000      20.00      238.0            1.7              0.8            2.3        4.83(10)  -6 560.87        148.0          6.76        16.86    144.0      3.20    12.13 III.1  17.0000      17.00      221.2            8.4              2.1          17.8        3.15(10)-5      3655.51        144.4        44.10        16.76    140.4      2.92    49.09
* void volume in the HalfPACT with one direct load SWB is 1,496 liters Table 3.4 HalfPACT Pressure Increase with 4 Drums Overpacked in 1 SWB, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents        Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material  Drum      Package Temperature        Value, Geff      Energy        Value, Geff      Rate        STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type    (watts)    (watts)    (&deg;F)      (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)      (&deg;F)    (psia)    (psig)
I.1    5.0000      20.00      238.0            2.4              0            2.4        4.99(10)-6      579.45        148.0          4.41        16.86    144.0      3.20      9.78 II.1    5.0000      20.00      238.0            1.7              0.8            2.3        4.83(10)  -6 560.87        148.0          4.26        16.86    144.0      3.20      9.63 III.1    5.0000      20.00      238.0            8.4              2.1          19.0        3.96(10)-5      4599.58        148.0        35.28        16.86    144.0      3.20    40.65
* void volume in the HalfPACT with four 55-gallon drums in one SWB overpack is 2,366 liters 3.4-15
 
HalfPACT Safety Analysis Report                                                                                                                                    Rev. 9, August 2022 Table 3.4 HalfPACT Pressure Increase with 4 85-Gallon Drums or 4 55-Gallon Drums Overpacked in 4 85-Gallon Drums, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents        Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material  Drum      Package Temperature        Value, Geff      Energy        Value, Geff      Rate        STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type    (watts)    (watts)      (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)      (&deg;F)    (psia)    (psig)
I.1    5.0000      20.00      238.0            2.4              0            2.4        4.99(10)-6      579.45        148.0          6.32        16.86    144.0      3.20    11.69 II.1    5.0000      20.00      238.0            1.7              0.8            2.3        4.83(10)  -6 560.87        148.0          6.17        16.86    144.0      3.20    11.54 III.1    4.5000      18.00      226.8            8.4              2.1          18.2        3.41(10)-5      3959.75        145.6        43.07        16.80    141.6      3.01    48.18
* void volume in the HalfPACT with four 85-gallon drums is 1,664 liters Table 3.4 HalfPACT Pressure Increase with 3 100-Gallon Drums, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents        Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material  Drum      Package Temperature        Value, Geff      Energy        Value, Geff      Rate        STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type    (watts)    (watts)      (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)      (&deg;F)    (psia)    (psig)
I.1    6.6667      20.00      238.0            2.4              0            2.4        4.99(10)-6      579.45        148.0          5.29        16.86    144.0      3.20    10.66 II.1    6.6667      20.00      238.0            1.7              0.8            2.3        4.83(10)  -6 560.87        148.0          5.15        16.86    144.0      3.20    10.51 III.1    6.6667      20.00      238.0            8.4              2.1          19.0        3.96(10)-5      4599.58        148.0        42.19        16.86    144.0      3.20    47.56
* void volume in the HalfPACT with three 100-gallon drums is 1,978 liters Table 3.4 HalfPACT Pressure Increase with 3 SC-30G1 Shielded Containers, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents        Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material  Drum      Package Temperature        Value, Geff      Energy        Value, Geff      Rate        STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type    (watts)    (watts)      (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)      (&deg;F)    (psia)    (psig)
I.1    10.0000      30.00      178.3            2.4              0            2.4        7.49(10)-6      869.75        154.0          7.64        17.03    148.0      3.53    13.50 II.1  10.0000      30.00      178.3            1.7              0.8            2.1        6.58(10)  -6 764.08        154.0          6.62        17.03    148.0      3.53    12.48 III.1    9.3333      28.00      174.1            8.4              2.1          14.5        4.22(10)-5      4894.53        151.4        42.63        16.96    145.8      3.35    48.24
* void volume in the HalfPACT with three SC-30G1s is 2,100 liters 3.4-16
 
HalfPACT Safety Analysis Report                                                                                                                                  Rev. 9, August 2022 Table 3.4 HalfPACT Pressure Increase with 7 CCOs, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents      Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor    Increase Material    CCO      Package Temperature      Value, Geff      Energy        Value, Geff        Rate      STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type      (watts)    (watts)    (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)        (&deg;F)    (psia)    (psig)
I.1    4.2857      30.00      157.1            2.4              0              2.4          7.49E-06        869.75        137.8          8.38        16.58      133.2      2.42    12.68 II.1    4.2857      30.00      157.1            1.7            0.8            2.0          6.32E-06        733.89        137.8          7.06        16.58      133.2      2.42    11.36 III.1    4.1429      29.00      155.8            8.4            2.1            13.2          3.99E-05      4636.74        137.1        44.84        16.56      132.6      2.39    49.09
* void volume in the HalfPACT with 7 CCOs is 1,846 liters Table 3.4 HalfPACT Pressure Increase with 2 SC-30G2 Shielded Containers, 60-Day Duration*
Decay Total Decay  Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste    Heat per  Heat per  Contents      Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material    Drum    Package Temperature      Value, Geff      Energy        Value, Geff        Rate      STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type      (watts)    (watts)    (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)        (&deg;F)    (psia)    (psig)
I.1    15.0000      30.00    174.1            2.4              0              2.4          7.49E-06        869.75        135.5          7.11        16.52    130.2      2.23    11.16 II.1  15.0000      30.00    174.1            1.7            0.8            2.1          6.53E-06        758.27        135.5          6.20        16.52      130.2      2.23    10.25 III.1  15.0000      30.00    174.1            8.4            2.1            14.5          4.52E-05      5244.05        135.5        42.90        16.52      130.2      2.23    46.95
* void volume in the HalfPACT with two SC-30G2s is 2,175 liters Table 3.4 HalfPACT Pressure Increase with 1 SC-30G3 Shielded Container, 60-Day Duration*
Decay Total Decay  Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste    Heat per  Heat per  Contents      Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material    Drum    Package Temperature      Value, Geff      Energy        Value, Geff        Rate      STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type      (watts)    (watts)    (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)        (&deg;F)    (psia)    (psig)
I.1    30.0000    30.0000    212.7            2.4              0              2.4          7.49E-06        869.75        133.9          7.02        16.47    129.9      2.21    11.00 II.1  30.0000    30.0000    212.7            1.7            0.8            2.2          6.97E-06        809.37        133.9          6.53        16.47      129.9      2.21    10.51 III.1  28.0000    28.0000    206.7            8.4            2.1            16.8          4.88E-05      5665.57        133.1        45.64        16.45      129.3      2.18    49.57
* void volume in the HalfPACT with one SC-30G3 is 2.200 liters 3.4-17
 
HalfPACT Safety Analysis Report                                                                                                                                  Rev. 9, August 2022 Table 3.4 HalfPACT Pressure Increase with 2 SC-55G1 Shielded Containers, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste    Heat per  Heat per  Contents      Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor  Increase Material    Drum    Package Temperature      Value, Geff      Energy        Value, Geff        Rate      STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type      (watts)    (watts)    (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)      (liters)        (&deg;F)    Increase (psia) (psia)        (&deg;F)    (psia)    (psig)
I.1  15.0000      30.00    163.9            2.4              0              2.4          7.49E-06        869.75        134.7          7.02        16.49    130.3      2.24    11.06 II.1  15.0000      30.00    163.9            1.7            0.8            2.1          6.40E-06        743.18        134.7          6.00        16.49      130.3      2.24    10.03 III.1  15.0000      30.00    163.9            8.4            2.1            13.8          4.30E-05      4993.23        134.7        40.33        16.49      130.3      2.24    44.36
* void volume in the HalfPACT with two SC-55G1s is 2,200 liters Table 3.4 HalfPACT Pressure Increase with 1 SC-55G2 Shielded Container, 60-Day Duration*
Decay Total Decay    Average                                      Temperature    Radiolytic Gas Radiolytic Gas Average ICV                Initial Gas Minimum    Water  Pressure Waste  Heat per    Heat per  Contents      Total Gas      Activation    Correlation    Generation    Generation      Gas      Radiolytic Gas Pressure    ICV Wall  Vapor    Increase Material  Drum      Package Temperature      Value, Geff      Energy        Value, Geff        Rate      STP/60 days Temperature      Pressure    Increase Temperature Pressure @ 60 days Type    (watts)    (watts)    (&deg;F)    (molecules/100eV) (kcal/g-mole) (molecules/100eV) (moles/sec)        (liters)        (&deg;F)    Increase (psia) (psia)        (&deg;F)    (psia)    (psig)
I.1  30.0000    30.0000    198.5            2.4              0              2.4          7.49E-06        869.75        135.0          7.26        16.50      131.0      2.28    11.34 II.1  30.0000    30.0000    198.5            1.7            0.8            2.2          6.81E-06        790.79        135.0          6.60        16.50      131.0      2.28    10.68 III.1  28.0000    28.0000    193.4            8.4            2.1            15.8          4.61E-05      5347.40        134.2        44.57        16.48      130.4      2.24    48.59
* void volume in the HalfPACT with one SC-55G2 is 2,130 liters 3.4-18
 
HalfPACT Safety Analysis Report                    Rev. 9, August 2022 Figure 3.4 HalfPACT Packaging Thermal Model Node Layout 3.4-19
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 3.4 Seven 55-Gallon Drum Payload Thermal Node Layout 3.4-20
 
HalfPACT Safety Analysis Report                                                            Rev. 9, August 2022 3.5 Thermal Evaluation for Hypothetical Accident Conditions This section presents the results of thermal testing of the HalfPACT package for the hypothetical accident condition (HAC) specified in 10 CFR &sect;71.73(c)(4) 1.
3.5.1 Thermal Model 3.5.1.1      Analytical Model Consistent with the Summary and Resolution of Public Comments relating to &sect;71.73, the effects of solar radiation may be neglected before and during the thermal test, the initial conditions for the HAC thermal event ignore insolation. Table 3.5-1 summarizes component temperatures with the maximum decay heat load of 30 watts, but ignoring insolation. These analyses utilize the NCT model as described in Section 3.4.1, Thermal Model, and provide a basis for adjusting temperatures to compensate for an ambient starting temperature for the HAC fire test that was under 100 &#xba;F.
3.5.1.2      Test Model HAC thermal event (fire) testing was performed on two prototypical HalfPACT packages, identified as the HalfPACT engineering test unit (ETU) and certification test unit (CTU). A full description of the ETU and CTU, the test facilities, the pre-fire damage and initial orientation in the fire, and the test results is presented in Appendix 2.10.3, Certification Tests.
Unlike the ETU that did not use any temperature measuring devices, the CTU utilized passive, non-reversible temperature indicating labels at various locations near the ICV and OCV seal flanges to record temperatures from the HAC fire test. Each set of temperature indicating labels recorded temperatures in 40 steps from 105 &#xba;F to 500 &#xba;F. As illustrated in Figure 3.5-1, some locations used redundant sets of labels to ensure comprehensive results at critical regions.
3.5.2 Package Conditions and Environment As discussed further in Appendix 2.10.3, Certification Tests, the CTU was oriented horizontally in a stand a distance one meter above the fuel per the requirements of 10 CFR &sect;71.73(c)(4).
With reference to Figure 3.5-1, the CTU was oriented circumferentially at an angle of 305&#xba; to position the damage from Drops 1, 2, and 4 (0&#xba;) and the damage from Drop 5 (250&#xba;) a distance 1/2 meter above the lowest part of the package on the stand (i.e., 11/2 meters above the fuel 2).
This particular arrangement put the maximum drop damage in the hottest part of the fire.
1 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 M. E. Schneider and L. A. Kent, Measurements of Gas Velocities and Temperatures in a Large Open Pool Fire, Sandia National Laboratories (reprinted from Heat and Mass Transfer in Fire, A. K. Kulkarni and Y. Jaluria, Editors, HTD-Vol. 73 (Book No. H00392), American Society of Mechanical Engineers). Figure 3 shows that maximum temperatures occur at an elevation approximately 2.3 meters above the pool floor. The pool was initially filled with water and fuel to a level of 0.814 meters. The maximum temperatures therefore occur approximately 11/2 meters above the level of the fuel, i.e., 1/2 meter above the lowest part of the package when set one meter above the fuel source per the requirements of 10 CFR &sect;71.73(c)(4).
3.5-1
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 As discussed earlier, no active temperature measuring devices were employed prior to, during, or following the HAC fire test. Further, measurement of the OCA outer shell temperature does not represent the OCV or ICV temperatures due to the large internal mass and thick, thermally insulating foam used within the OCA. As discussed earlier in Section 3.1.1, Packaging, the temperatures of the OCV, ICV, and payload are effectively decoupled from the OCA outer shell and polyurethane foam for short term thermal transients. Instead, the initial temperature of the CTU may be estimated based on the ambient temperature of the Sandia National Laboratory testing facilities in the six weeks prior to the HAC fire test 3. Climatological data for Albuquerque, New Mexico, during the month of March and first two weeks of April 1998 shows an average temperature of 48 &#xba;F for those six weeks. Thus, when adjusting for the elevation difference between the testing facilities and Albuquerque, the initial temperature for HAC fire testing is taken as 43 &#xba;F.
The exterior surface of the CTU was painted, an option allowed on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. Having paint present on the OCA exterior surface is conservative for the HAC fire test because of the relatively high emissivity of paint
( > 0.90) compared to that of bare stainless steel ( = 0.25). The higher emissivity results in higher heat flow into the CTU during the HAC fire test, but the net affect is small since the paint burns away shortly after the start of the fire.
Prior to the beginning of the HAC fire test, average wind speed was determined to be below 10 miles per hour. As discussed in Appendix 2.10.3, Certification Tests, the length of time of the fully engulfing, HAC fire test was approximately 33 minutes, and the ambient air temperature was 51 &#xba;F.
3.5.3 Package Temperatures As stated in Section 3.5.1.1, Analytical Model, initial condition temperatures for the HAC fire test are presented in Table 3.5-1. Accordingly, the average temperature of the ICV wall and OCV wall is 133 &#xba;F and 131 &#xba;F, respectively. As stated in Section 3.5.2, Package Conditions and Environment, the actual starting temperature of the CTU was 51 &#xba;F. Therefore, the difference between the actual and theoretical pre-fire package temperature is conservatively taken as 133 &#xba;F - 43
&#xba;F = 90 &#xba;F.
As discussed in Appendix 2.10.3, Certification Tests, the duration of the HAC fire test was 33 minutes. In addition, the time-averaged temperature of the HAC fire was 1,486 &#xba;F. Both the test duration and fire temperature exceeded the requirements of 10 CFR &sect;71.73(c)(4).
A summary of temperature indicating label temperatures is presented in Table 3.5-2. The maximum measured OCV seal region temperature was 200 &#xba;F. Upwardly adjusting for the lower, pre-fire starting temperature by 90 &#xba;F results in a projected maximum OCV seal region temperature of 290 &#xba;F. The maximum measured ICV seal region temperature was 110 &#xba;F. Also, upwardly adjusting for the lower, pre-fire starting temperature by 90 &#xba;F results in a projected maximum ICV seal region temperature of 200 &#xba;F. In comparison, certification testing of the 3
CTU was located at Sandia National Laboratories Coyote Canyon drop test facility for the month of March, 1998, and the Lurance Canyon burn facility for the first two weeks of April, 1998. CTU was burned on April 14, 1998.
The elevation difference between the two test facilities and the city of Albuquerque results in an average ambient temperature approximately 5 &#xba;F cooler than Albuquerque.
3.5-2
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 TRUPACT-II package showed a maximum OCV seal region temperature of 260 &#xba;F, and a maximum ICV seal region temperature of 200 &#xba;F (see Table 3.5-5 from Section 3.5.3, Package Temperatures, of the TRUPACT-II SAR 4). As with the comparison of measurements of drop damage, fire temperatures between the two similar package designs agree very well.
3.5.4 Maximum Internal Pressure The maximum internal pressure for the ICV may be conservatively determined by assuming the air temperature within the ICV is at the maximum seal temperature of 200 &#xba;F. The ICV pressure increase, PICV, using an initial maximum ICV wall temperature of 154 &#xba;F (from Table 3.4-1) at an initial pressure equal to the MNOP of 50 psig (64.7 psia), is determined using ideal gas relationships:
P1 P2            P154  F P200  F                            T200  F
                        =                      =              P200  F = P154  F T1 T2            T154  F T200  F                            T 154 F 200 + 460 P200  F = 64.7                = 69.5 psia (54.8 psig) 154 + 460 PICV = 54.8  50.0 = 4.8 psig Thus, the maximum internal pressure for the ICV for HAC is 54.8 psig, resulting in a net pressure increase of 4.8 psig. In comparison, certification testing of the TRUPACT-II package showed a ICV pressure increase of 2.6 psig (see Section 3.5.4, Maximum Internal Pressure, of the TRUPACT-II SAR). The difference in PICV is due to the conservative assumption of using maximum seal region temperature rather than average air temperature for determining the pressure increase. Unlike TRUPACT-II certification testing, actual measurement of internal pressure was not performed for HalfPACT certification testing, hence, the conservatism.
The maximum internal pressure for the OCV may be conservatively determined by assuming the air temperature within the OCV, 245 &#xba;F, is the average of the maximum ICV and OCV seal temperatures of 200 &#xba;F and 290 &#xba;F, respectively. The initial air temperature within the OCV, 152 &#xba;F, is the average of the maximum OCV and ICV wall temperatures of 150 &#xba;F and 154 &#xba;F, respectively (from Table 3.4-1). The OCV pressure increase, POCV, using at an initial pressure equal to the MNOP of 50 psig (64.7 psia), is determined using ideal gas relationships:
P1 P2            P152  F  P245  F                          T245  F
                        =                      =              P245  F = P152  F T1 T2            T152  F  T245  F                          T 152 F 245 + 460 P245  F = 64.7                = 74.5 psia (59.8 psig) 152 + 460 P = 59.8  50.0 = 9.8 psig Thus, the maximum internal pressure for the OCV for HAC is 59.8 psig, resulting in a net pressure increase of 9.8 psig. In comparison, certification testing of the TRUPACT-II package 4
U.S. Department of Energy (DOE), Safety Analysis Report for the TRUPACT-II Shipping Package, USNRC Docket No. 71-9218, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
3.5-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 showed a maximum OCV pressure increase of 4.6 psig (see Section 3.5.4, Maximum Internal Pressure, of the TRUPACT-II SAR). As is the case for the ICV, the difference in POCV is due to the conservative assumption of using maximum seal region temperature rather than average air temperature for determining the pressure increase. Unlike TRUPACT-II certification testing, actual measurement of internal pressure was not performed for HalfPACT certification testing, hence, the conservatism.
3.5.5 Maximum Thermal Stresses As shown in Section 3.5.4, Maximum Internal Pressure, the internal pressure within the ICV increases 4.8 psig (+10%), and within the OCV increases 9.8 psig (+20%) due to the HAC fire test. Pressure stresses due to the HAC fire test corresponding increase a maximum of 20%.
With reference to Table 2.1-1 in Section 2.1.2.1.1, Containment Structure (ICV), the HAC allowable stress intensity for general primary membrane stresses (applicable to pressure loads) is 240% of the NCT allowable stress intensity. Therefore, a HAC pressure stress increase of 20%
will not exceed the HAC allowable stresses. Further discussion regarding HAC thermal stresses is presented in Section 2.7.4, Thermal.
3.5.6 Evaluation of Package Performance for the Hypothetical Accident Thermal Conditions The most temperature sensitive material in the HalfPACT package is the butyl rubber used for the containment O-ring seals. The certification test unit (CTU), when subjected to the rigors of the HAC free drops, puncture drops, and fire testing, was shown to be leaktight (i.e.,
demonstrating a leakage rate of 1 x 10-7 standard cubic centimeters per second (scc/s), air, or better) for both the OCV and ICV. Following testing, the maximum OCV and ICV seal temperatures were recorded as 290 &#xba;F and 200 &#xba;F, respectively, temperatures well below the 360 &#xba;F O-ring seal material limit for short durations (8 hours).
With regard to the criticality analyses of Chapter 6.0, Criticality Evaluation, the minimum remaining polyurethane foam for the CTU averaged approximately five inches. Sufficient polyurethane foam material remained to validate modeling assumptions used in the criticality analyses.
3.5-4
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 3.5 NCT Steady-State Temperatures with 30 Watts Decay Heat Load and Zero Insolation; Seven 55-Gallon Drums Temperature (&#xba;F)
Case 1          Case 2 (Uniform Heat in  (Uniform Heat in Solar  All Seven Drums)    Center Drum    Maximum Location        Loading                          Only)        Allowable Center Drum Centerline
* Maximum              N/A          169.0            328.9          N/A
* Average              N/A          154.4            239.2 Center Drum Wall
* Maximum              N/A          141.6            150.4          2,750
* Average              N/A          141.0            148.8          2,750 Outer Drum Centerline
* Maximum              N/A          166.5            138.8          N/A
* Average              N/A          152.6            138.6 Outer Drum Wall
* Maximum              N/A          141.4            147.9          2,750
* Average              N/A          137.4            138.2          2,750 Average All Drums
* Centerline            N/A          152.9            153.0
* Wall                  N/A          137.9            139.7          2,750 ICV Wall
* Maximum              N/A          138.0            140.4          800
* Average              N/A          133.1            133.2          800
* Minimum              N/A          129.8            129.6          800 ICV Air
* Average              N/A          135.5            136.5          N/A ICV Main O-ring Seal
* Maximum              N/A          130.8            130.3      -40 to 225 OCV Wall
* Maximum              N/A          133.7            134.5          800
* Average              N/A          130.4            131.1          800 OCV Main O-ring Seal
* Maximum              N/A          129.0            128.6      -40 to 225 Polyurethane Foam
* Maximum              N/A          125.8            126.3          300
* Average              N/A          112.3            112.3          300 OCA Outer Shell
* Maximum              N/A          101.6            101.6          185 3.5-5
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Notes for Table 3.5-1:
The temperature limit for the waste material is discussed in Appendix 6.6 of the CH-TRU Payload Appendices.
Temperature limit based on the minimum melting temperature for carbon steel (see Section 3.3, Technical Specifications of Components).
Temperature limit based on the ASME B&PV Code.
Temperature limits based on the allowable long-term temperature range for butyl rubber (see Section 3.3, Technical Specifications of Components).
Temperature limit based on the maximum operating limit for polyurethane foam (see Section 3.3, Technical Specifications of Components).
Temperature limit based on the maximum accessible surface temperature for exclusive use shipments per 10 CFR 71.43(g).
Table 3.5 HAC Thermal Event Temperature Readings Location                              Number      Temperature OCV Conical Shell at 0&#xba; (near Vent Port) - Drop Tests 1, 2, 4      1a, 1b      180 &#xba;F, 170 &#xba;F OCV Conical Shell at 110&#xba; - Drop Test 6                                2          180 &#xba;F OCV Conical Shell at 250&#xba; - Drop Test 5                                3          130 &#xba;F OCV Seal Flange at 0&#xba; (near Main Seals) - Drop Tests 1, 2, 4        4a, 4b      200 &#xba;F, 200 &#xba;F OCV Seal Flange at 110&#xba; (near Main Seals) - Drop Test 6                5          200 &#xba;F OCV Seal Flange at 1471/2&#xba; (near Main Seals) - Drop Test 3              6          180 &#xba;F OCV Seal Flange at 250&#xba; (near Main Seals) - Drop Test 5                7          140 &#xba;F ICV Seal Flange at 0&#xba; (near Vent Port) - Drop Tests 1, 2, 4            8          105 &#xba;F ICV Seal Flange at 0&#xba; (near Main Seals) - Drop Tests 1, 2, 4          9          105 &#xba;F ICV Seal Flange at 110&#xba; (near Main Seals) - Drop Test 6              10          105 &#xba;F ICV Seal Flange at 1471/2&#xba; (near Main Seals) - Drop Test 3              11          110 &#xba;F ICV Seal Flange at 250&#xba; (near Main Seals) - Drop Test 5              12          110 &#xba;F 3.5-6
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Figure 3.5 HAC Thermal Event Temperature Indicating Label Locations 3.5-7
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
3.5-8
 
HalfPACT Safety Analysis Report                Rev. 9, August 2022 3.6 Appendices 3.6.1 Computer Analysis Results 3.6.2 Thermal Model Details 3.6-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
3.6-2
 
HalfPACT Safety Analysis Report                                                                      Rev. 9, August 2022 3.6.1        Computer Analysis Results 3.6.1.1        Seven 55-Gallon Drum Payload with 100 &#xba;F Ambient and Full Solar Loading, Uniformly Distributed Decay Heat Load (Case 1)
SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    8 MODEL = WHOLE              HALF PACK w/7 55G Drums, 30W Uniform Heat Dist +100F w/solar 10/20 STDSTL SINDA/FLUINT v3.1    Runtime: 7/13/98 13:47 SUBMODEL NAME = HalfPACT CALCULATED                              ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(HalfPACT 2202)= 4.882812E-04 VS. DRLXCA= 5.000000E-04 MAX ARITH DELTA T PER ITER      ARLXCC(HalfPACT 2203)= 9.765625E-04 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 2.209933E-02 VS. EBALSA
* ESUMIS      = 0.341709 EBALSA= 1.000000E-03 ENERGY INTO AND OUT OF SYS      ESUMIS                = 341.709          ESUMOS= 350.215 MAX NODAL ENERGY BALANCE        EBALNC(HalfPACT 2212)= 6.202337E-03 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS            LOOPCT                =    648      VS. NLOOPS=  20000 PROBLEM TIME                    TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  1001=  129.88    T  1002=  130.76      T 1003= 132.83      T 1004= 136.29        T 1005=  143.51    T  1006=  150.14 T  1011=  129.33    T  1012=  129.80      T 1013= 131.60      T 1014= 135.00        T 1015=  142.27    T  1016=  148.66 T  1021=  119.70    T  1022=  121.18      T 1023= 124.56      T 1024= 129.69        T 1025=  138.72    T  1026=  145.66 T  1031=  119.28    T  1032=  121.35      T 1033= 125.78      T 1034= 131.71        T 1035=  140.19    T  1036=  145.41 T  1041=  119.22    T  1042=  122.18      T 1043= 127.26      T 1044= 134.38        T 1045=  141.90    T  1046=  144.74 T  1047=  145.49    T  1052=  119.18      T 1053= 121.86      T 1054= 126.41        T 1058=  141.39    T  1059=  145.55 T  1062=  119.00    T  1063=  120.81      T 1064= 124.70      T 1065= 129.92        T 1066=  139.86    T  1067=  147.35 T  1071=  118.91    T  1072=  120.57      T 1073= 124.18      T 1074= 129.10        T 1075=  138.94    T  1076=  147.17 T  1081=  118.29    T  1082=  118.88      T 1083= 120.17      T 1084= 121.93        T 1085=  125.46    T  1086=  135.89 T  1087=  146.36    T  1091=  116.53      T 1092= 116.45      T 1093= 116.43        T 1094=  116.60    T  1095=  117.09 T  1101=  105.68    T  1102=  106.80      T 1103= 109.20      T 1104= 112.71        T 1111=  102.56    T  1112=  104.60 T  1113=  108.64    T  1114=  113.63      T 1115= 122.48      T 1121= 102.60        T 1122=  106.50    T  1123=  114.35 T  1124=  124.29    T  1125=  137.32      T 1126= 144.83      T 2001= 151.35        T 2011=  150.83    T  2021=  146.33 T  2031=  146.87    T  2032=  147.10      T 2041= 147.62      T 2051= 147.91        T 2061=  148.12    T  2071=  148.06 T  2081=  149.43    T  2121=  148.96      T 2202= 153.14      T 2212= 152.89        T 2282=  152.94    T  2322=  153.17 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER T  1055=  128.07    T  1056=  129.38      T 1057= 132.68      T 2201= 152.87        T 2203=  153.60    T  2211=  152.70 T  2213=  153.04    T  2281=  152.64      T 2283= 153.20      T 2321= 152.55        T 2323=  153.88 HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER T      1=  100.00 SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    11 MODEL = WHOLE              HALF PACK w/7 55G Drums, 30W Uniform Heat Dist +100F w/solar 10/20 STDSTL SUBMODEL NAME = DRUMS SINDA/FLUINT v3.1    Runtime:  7/13/98  13:47 CALCULATED                              ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(DRUMS    3540)= 3.662109E-04 VS. DRLXCA= 5.000000E-04 MAX ARITH DELTA T PER ITER      ARLXCC(            0)= 0.000000E+00 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 4.037903E-03 VS. EBALSA
* ESUMIS      = 8.532419E-03 EBALSA= 1.000000E-03 ENERGY INTO AND OUT OF SYS      ESUMIS                = 8.53242          ESUMOS= 0.000000E+00 MAX NODAL ENERGY BALANCE        EBALNC(DRUMS    2413)= 6.148017E-04 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS            LOOPCT                =    648      VS. NLOOPS=  20000 PROBLEM TIME                    TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  2403=  155.17    T  2404=  154.66      T 2413= 153.96      T 2414= 153.66        T 3300=  155.53    T  3302=  155.53 T  3304=  155.54    T  3306=  155.57      T 3308= 156.03      T 3312= 154.44        T 3314=  154.63    T  3316=  155.39 T  3318=  155.87    T  3322=  154.30      T 3324= 154.30      T 3326= 154.32        T 3328=  154.61    T  3332=  154.24 T  3334=  154.17    T  3336=  153.90      T 3338= 152.26      T 3340= 154.29        T 3342=  154.20    T  3344=  154.07 T  3346=  153.58    T  3348=  150.47      T 3400= 173.96      T 3402= 173.70        T 3404=  172.43    T  3406=  168.61 T  3408=  156.51    T  3412=  172.11      T 3414= 171.17      T 3416= 167.87        T 3418=  156.33    T  3422=  171.91 T  3424=  170.74    T  3426=  167.01      T 3428= 154.95      T 3432= 171.57        T 3434=  170.03    T  3436=  165.60 T  3438=  151.86    T  3440=  172.02      T 3442= 171.38      T 3444= 169.61        T 3446=  164.73    T  3448=  149.80 T  3500=  181.87    T  3502=  181.47      T 3504= 179.53      T 3506= 173.80        T 3508=  156.87    T  3512=  179.57 T  3514=  178.02    T  3516=  172.85      T 3518= 156.68      T 3522= 179.35        T 3524=  177.55    T  3526=  171.99 T  3528=  155.21    T  3532=  178.89      T 3534= 176.61      T 3536= 170.22        T 3538=  151.81    T  3540=  179.53 T  3542=  178.64    T  3544=  176.08      T 3546= 169.18      T 3548= 149.72        T 3600=  184.00    T  3602=  183.55 T  3604=  181.39    T  3606=  175.11      T 3608= 157.07      T 3612= 181.53        T 3614=  179.79    T  3616=  174.09 T  3618=  156.87    T  3622=  181.28      T 3624= 179.30      T 3626= 173.21        T 3628=  155.36    T  3632=  180.77 T  3634=  178.26    T  3636=  171.30      T 3638= 151.82      T 3640= 181.49        T 3642=  180.51    T  3644=  177.69 T  3646=  170.22    T  3648=  149.78      T 3700= 156.39      T 3702= 156.39        T 3704=  156.35    T  3706=  156.26 T  3708=  156.08    T  3712=  155.59      T 3714= 155.78      T 3716= 155.98        T 3718=  155.91    T  3722=  155.35 T  3724=  155.36    T  3726=  155.21      T 3728= 154.67      T 3732= 154.96        T 3734=  154.68    T  3736=  153.97 T  3738=  151.76    T  3740=  155.19      T 3742= 154.73      T 3744= 154.26        T 3746=  153.20    T  3748=  149.94 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
3.6.1-1
 
HalfPACT Safety Analysis Report                                                                      Rev. 9, August 2022 3.6.1.2        Seven 55-Gallon Drum Payload with 100 &#xba;F Ambient and Full Solar Loading, All Decay Heat Load in Center Drum Only (Case 2)
SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    4 MODEL = WHOLE              HALF PACK w/7 55G Drums, One Drum Heat +100F w/solar 7/8/98 STDSTL SINDA/FLUINT v3.1    Runtime: 7/13/98 16:56 SUBMODEL NAME = HalfPACT CALCULATED                                ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(HalfPACT  1006)= 7.263184E-03 VS. DRLXCA= 1.000000E-02 MAX ARITH DELTA T PER ITER    ARLXCC(HalfPACT  2203)= 8.361816E-03 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 0.328712    VS. EBALSA
* ESUMIS        =  3.41709 EBALSA= 1.000000E-02 ENERGY INTO AND OUT OF SYS    ESUMIS                = 341.709          ESUMOS= 349.835 MAX NODAL ENERGY BALANCE      EBALNC(HalfPACT  2212)= 8.322538E-02 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS          LOOPCT                =    318      VS. NLOOPS=    20000 PROBLEM TIME                  TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  1001=  129.88    T  1002=  130.68      T 1003= 132.60      T 1004= 135.89        T 1005=  142.90    T  1006= 149.60 T  1011=  129.32    T  1012=  129.72      T 1013= 131.35      T 1014= 134.55        T 1015=  141.51    T  1016= 147.76 T  1021=  119.68    T  1022=  121.09      T 1023= 124.31      T 1024= 129.18        T 1025=  137.77    T  1026= 144.37 T  1031=  119.24    T  1032=  121.20      T 1033= 125.37      T 1034= 130.97        T 1035=  138.96    T  1036= 143.87 T  1041=  119.17    T  1042=  121.97      T 1043= 126.75      T 1044= 133.46        T 1045=  140.55    T  1046= 143.22 T  1047=  143.92    T  1052=  119.14      T 1053= 121.66      T 1054= 125.93        T 1058=  140.03    T  1059= 143.93 T  1062=  118.96    T  1063=  120.66      T 1064= 124.30      T 1065= 129.20        T 1066=  138.51    T  1067= 145.49 T  1071=  118.88    T  1072=  120.45      T 1073= 123.86      T 1074= 128.52        T 1075=  137.84    T  1076= 145.65 T  1081=  118.28    T  1082=  118.84      T 1083= 120.06      T 1084= 121.74        T 1085=  125.10    T  1086= 135.24 T  1087=  145.46    T  1091=  116.53      T 1092= 116.44      T 1093= 116.39        T 1094=  116.52    T  1095= 116.94 T  1101=  105.67    T  1102=  106.78      T 1103= 109.15      T 1104= 112.61        T 1111=  102.54    T  1112= 104.55 T  1113=  108.53    T  1114=  113.43      T 1115= 122.11      T 1121= 102.58        T 1122=  106.46    T  1123= 114.25 T  1124=  124.12    T  1125=  137.07      T 1126= 144.54      T 2001= 151.09        T 2011=  150.15    T  2021= 144.85 T  2031=  145.18    T  2032=  145.39      T 2041= 145.79      T 2051= 146.00        T 2061=  146.18    T  2071= 146.47 T  2081=  148.60    T  2121=  149.13      T 2202= 153.54      T 2212= 152.33        T 2282=  152.28    T  2322= 154.66 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER T  1055=  127.48    T  1056=  128.72      T 1057= 131.83      T 2201= 153.17        T 2203=  154.93    T  2211= 152.12 T  2213=  152.33    T  2281=  151.97      T 2283= 152.26      T 2321= 153.85        T 2323=  157.27 HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER T      1=  100.00 SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    5 MODEL = WHOLE              HALF PACK w/7 55G Drums, One Drum Heat +100F w/solar 7/8/98 STDSTL SINDA/FLUINT v3.1    Runtime: 7/13/98 16:56 SUBMODEL NAME = DRUMS CALCULATED                                ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(DRUMS    3748)= 5.126953E-03 VS. DRLXCA= 1.000000E-02 MAX ARITH DELTA T PER ITER    ARLXCC(            0)= 0.000000E+00 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 7.856413E-02 VS. EBALSA
* ESUMIS        = 8.532490E-02 EBALSA= 1.000000E-02 ENERGY INTO AND OUT OF SYS    ESUMIS                = 8.53249          ESUMOS= 0.000000E+00 MAX NODAL ENERGY BALANCE      EBALNC(DRUMS    2413)= 1.220922E-02 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS          LOOPCT                =    318      VS. NLOOPS=    20000 PROBLEM TIME                  TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  2403=  159.76    T  2404=  158.18      T 2413= 152.35      T 2414= 152.34        T 3300=  162.13    T  3302= 162.11 T  3304=  162.01    T  3306=  161.77      T 3308= 161.53      T 3312= 153.21        T 3314=  154.35    T  3316= 158.90 T  3318=  160.09    T  3322=  152.43      T 3324= 152.45      T 3326= 152.63        T 3328=  153.88    T  3332= 152.33 T  3334=  152.24    T  3336=  151.99      T 3338= 150.32      T 3340= 152.47        T 3342=  152.29    T  3344= 152.14 T  3346=  151.66    T  3348=  148.50      T 3400= 280.82      T 3402= 279.15        T 3404=  270.94    T  3406= 245.92 T  3408=  162.76    T  3412=  153.78      T 3414= 155.11      T 3416= 157.67        T 3418=  160.94    T  3422= 153.07 T  3424=  153.31    T  3426=  153.70      T 3428= 154.45      T 3432= 152.37        T 3434=  151.97    T  3436= 151.27 T  3438=  149.73    T  3440=  152.78      T 3442= 152.09      T 3444= 151.42        T 3446=  150.26    T  3448= 147.61 T  3500=  328.04    T  3502=  325.58      T 3504= 313.53      T 3506= 277.45        T 3508=  163.80    T  3512= 153.97 T  3514=  155.31    T  3516=  157.64      T 3518= 161.62      T 3522= 153.25        T 3524=  153.59    T  3526= 154.07 T  3528=  154.77    T  3532=  152.37      T 3534= 151.85      T 3536= 151.03        T 3538=  149.52    T  3540= 152.86 T  3542=  151.99    T  3544=  151.14      T 3546= 149.79      T 3548= 147.36        T 3600=  340.37    T  3602= 337.65 T  3604=  324.40    T  3606=  285.09      T 3608= 164.36      T 3612= 154.02        T 3614=  155.38    T  3616= 157.74 T  3618=  162.00    T  3622=  153.29      T 3624= 153.67      T 3626= 154.19        T 3628=  154.95    T  3632= 152.33 T  3634=  151.79    T  3636=  150.94      T 3638= 149.46      T 3640= 152.86        T 3642=  151.93    T  3644= 151.03 T  3646=  149.65    T  3648=  147.35      T 3700= 169.81      T 3702= 169.69        T 3704=  169.09    T  3706= 167.28 T  3708=  161.42    T  3712=  153.71      T 3714= 154.81      T 3716= 157.22        T 3718=  159.79    T  3722= 152.63 T  3724=  152.75    T  3726=  153.08      T 3728= 154.23      T 3732= 152.10        T 3734=  151.84    T  3736= 151.37 T  3738=  149.90    T  3740=  152.49      T 3742= 151.89      T 3744= 151.46        T 3746=  150.65    T  3748= 148.04 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
3.6.1-2
 
HalfPACT Safety Analysis Report                                                                      Rev. 9, August 2022 3.6.1.3        Seven 55-Gallon Drum Payload with 100 &#xba;F Ambient and No Solar Loading, Uniformly Distributed Decay Heat Load (Case 1)
SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    8 MODEL = WHOLE              HALF PACK w/7 55G Drums, 30W Uniform Heat Dist +100F w/o solar 10/
STDSTL SINDA/FLUINT v3.1    Runtime: 7/7/98 16:49 SUBMODEL NAME = HalfPACT CALCULATED                                ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(HalfPACT  2202)= 4.272461E-04 VS. DRLXCA= 5.000000E-04 MAX ARITH DELTA T PER ITER    ARLXCC(HalfPACT  2211)= 4.272461E-04 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 1.493508E-02 VS. EBALSA
* ESUMIS        = 0.000000E+00 EBALSA= 1.000000E-03 ENERGY INTO AND OUT OF SYS    ESUMIS                = 0.000000E+00      ESUMOS= 8.51318 MAX NODAL ENERGY BALANCE      EBALNC(HalfPACT  2212)= 3.714838E-03 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS          LOOPCT                =    731      VS. NLOOPS=    20000 PROBLEM TIME                  TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  1001=  100.09    T  1002=  102.70      T 1003= 107.56      T 1004= 114.07        T 1005=  124.94    T  1006= 133.68 T  1011=  100.24    T  1012=  102.70      T 1013= 107.32      T 1014= 113.55        T 1015=  123.98    T  1016= 132.12 T  1021=  100.97    T  1022=  102.50      T 1023= 106.07      T 1024= 111.57        T 1025=  121.40    T  1026= 129.02 T  1031=  101.28    T  1032=  103.45      T 1033= 108.08      T 1034= 114.33        T 1035=  123.31    T  1036= 128.87 T  1041=  101.37    T  1042=  104.48      T 1043= 109.80      T 1044= 117.28        T 1045=  125.19    T  1046= 128.17 T  1047=  128.97    T  1052=  101.38      T 1053= 104.19      T 1054= 108.97        T 1058=  124.73    T  1059= 129.08 T  1062=  101.21    T  1063=  103.15      T 1064= 107.30      T 1065= 112.88        T 1066=  123.51    T  1067= 131.53 T  1071=  101.12    T  1072=  102.94      T 1073= 106.88      T 1074= 112.24        T 1075=  122.92    T  1076= 131.72 T  1081=  100.66    T  1082=  101.53      T 1083= 103.40      T 1084= 105.91        T 1085=  110.72    T  1086= 123.00 T  1087=  131.75    T  1091=  100.38      T 1092= 100.68      T 1093= 101.46        T 1094=  102.65    T  1095= 105.26 T  1101=  100.44    T  1102=  100.84      T 1103= 101.78      T 1104= 103.27        T 1111=  100.85    T  1112= 102.10 T  1113=  104.61    T  1114=  107.77      T 1115= 113.52      T 1121= 101.56        T 1122=  104.26    T  1123= 109.70 T  1124=  116.62    T  1125=  125.76      T 1126= 131.11      T 2001= 135.11        T 2011=  134.58    T  2021= 129.85 T  2031=  130.50    T  2032=  130.76      T 2041= 131.41      T 2051= 131.84        T 2061=  132.32    T  2071= 132.65 T  2081=  134.66    T  2121=  134.63      T 2202= 137.15      T 2212= 136.89        T 2282=  138.21    T  2322= 138.49 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER T  1055=  110.70    T  1056=  112.14      T 1057= 115.60      T 2201= 136.86        T 2203=  137.62    T  2211= 136.68 T  2213=  137.05    T  2281=  137.92      T 2283= 138.45      T 2321= 137.96        T 2323=  139.18 HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER T      1=  100.00 SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    9 MODEL = WHOLE              HALF PACK w/7 55G Drums, 30W Uniform Heat Dist +100F w/o solar 10/
STDSTL SINDA/FLUINT v3.1    Runtime: 7/7/98 16:49 SUBMODEL NAME = DRUMS CALCULATED                                ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(DRUMS    2404)= 3.662109E-04 VS. DRLXCA= 5.000000E-04 MAX ARITH DELTA T PER ITER    ARLXCC(            0)= 0.000000E+00 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 4.457929E-03 VS. EBALSA
* ESUMIS        = 8.532419E-03 EBALSA= 1.000000E-03 ENERGY INTO AND OUT OF SYS    ESUMIS                = 8.53242          ESUMOS= 0.000000E+00 MAX NODAL ENERGY BALANCE      EBALNC(DRUMS    2413)= 1.191008E-03 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS          LOOPCT                =    731      VS. NLOOPS=    20000 PROBLEM TIME                  TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  2403=  139.33    T  2404=  138.79      T 2413= 138.05      T 2414= 137.73        T 3300=  139.70    T  3302= 139.70 T  3304=  139.70    T  3306=  139.75      T 3308= 140.30      T 3312= 138.55        T 3314=  138.76    T  3316= 139.56 T  3318=  140.12    T  3322=  138.41      T 3324= 138.41      T 3326= 138.44        T 3328=  138.83    T  3332= 138.35 T  3334=  138.27    T  3336=  138.00      T 3338= 136.41      T 3340= 138.40        T 3342=  138.30    T  3344= 138.16 T  3346=  137.66    T  3348=  134.49      T 3400= 158.56      T 3402= 158.30        T 3404=  157.01    T  3406= 153.14 T  3408=  140.84    T  3412=  156.66      T 3414= 155.72      T 3416= 152.36        T 3418=  140.64    T  3422= 156.46 T  3424=  155.28    T  3426=  151.49      T 3428= 139.23      T 3432= 156.11        T 3434=  154.54    T  3436= 150.04 T  3438=  136.07    T  3440=  156.57      T 3442= 155.92      T 3444= 154.10        T 3446=  149.11    T  3448= 133.85 T  3500=  166.72    T  3502=  166.31      T 3504= 164.33      T 3506= 158.51        T 3508=  141.27    T  3512= 164.37 T  3514=  162.80    T  3516=  157.53      T 3518= 141.06      T 3522= 164.14        T 3524=  162.32    T  3526= 156.65 T  3528=  139.57    T  3532=  163.68      T 3534= 161.36      T 3536= 154.85        T 3538=  136.10    T  3540= 164.33 T  3542=  163.42    T  3544=  160.81      T 3546= 153.76      T 3548= 133.87        T 3600=  169.01    T  3602= 168.56 T  3604=  166.36    T  3606=  159.96      T 3608= 141.58      T 3612= 166.52        T 3614=  164.75    T  3616= 158.93 T  3618=  141.36    T  3622=  166.28      T 3624= 164.26      T 3626= 158.05        T 3628=  139.85    T  3632= 165.77 T  3634=  163.22    T  3636=  156.13      T 3638= 136.28      T 3640= 166.49        T 3642=  165.50    T  3644= 162.63 T  3646=  155.01    T  3648=  134.13      T 3700= 141.18      T 3702= 141.17        T 3704=  141.13    T  3706= 141.03 T  3708=  140.76    T  3712=  140.40      T 3714= 140.57      T 3716= 140.77        T 3718=  140.58    T  3722= 140.19 T  3724=  140.17    T  3726=  140.00      T 3728= 139.36      T 3732= 139.87        T 3734=  139.60    T  3736= 138.89 T  3738=  136.52    T  3740=  140.06      T 3742= 139.67      T 3744= 139.23        T 3746=  138.19    T  3748= 134.66 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
3.6.1-3
 
HalfPACT Safety Analysis Report                                                                      Rev. 9, August 2022 3.6.1.4        Seven 55-Gallon Drum Payload with 100 &#xba;F Ambient and No Solar Loading, All Decay Heat Load in Center Drum Only (Case 2)
SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    4 MODEL = WHOLE              HALF PACK w/7 55G Drums, One Drum Heat +100F w/o solar 8/12/97 STDSTL SINDA/FLUINT v3.1    Runtime: 7/8/98 9:51 SUBMODEL NAME = HalfPACT CALCULATED                                ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(HalfPACT  1066)=-2.685547E-03 VS. DRLXCA= 1.000000E-02 MAX ARITH DELTA T PER ITER    ARLXCC(HalfPACT  2321)= 2.258301E-03 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 5.408887E-02 VS. EBALSA
* ESUMIS        = 0.000000E+00 EBALSA= 1.000000E-02 ENERGY INTO AND OUT OF SYS    ESUMIS                = 0.000000E+00      ESUMOS= 8.45246 MAX NODAL ENERGY BALANCE      EBALNC(HalfPACT  2212)= 1.684309E-02 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS          LOOPCT                =    507      VS. NLOOPS=    20000 PROBLEM TIME                  TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  1001=  100.09    T  1002=  102.72      T 1003= 107.64      T 1004= 114.24        T 1005=  125.34    T  1006= 134.50 T  1011=  100.24    T  1012=  102.71      T 1013= 107.36      T 1014= 113.65        T 1015=  124.19    T  1016= 132.52 T  1021=  100.97    T  1022=  102.49      T 1023= 106.04      T 1024= 111.52        T 1025=  121.31    T  1026= 128.90 T  1031=  101.26    T  1032=  103.41      T 1033= 107.99      T 1034= 114.16        T 1035=  123.02    T  1036= 128.49 T  1041=  101.36    T  1042=  104.42      T 1043= 109.67      T 1044= 117.04        T 1045=  124.84    T  1046= 127.78 T  1047=  128.56    T  1052=  101.36      T 1053= 104.13      T 1054= 108.83        T 1058=  124.34    T  1059= 128.61 T  1062=  101.19    T  1063=  103.09      T 1064= 107.16      T 1065= 112.62        T 1066=  123.00    T  1067= 130.80 T  1071=  101.11    T  1072=  102.90      T 1073= 106.78      T 1074= 112.07        T 1075=  122.60    T  1076= 131.29 T  1081=  100.66    T  1082=  101.53      T 1083= 103.40      T 1084= 105.91        T 1085=  110.72    T  1086= 123.09 T  1087=  131.89    T  1091=  100.38      T 1092= 100.69      T 1093= 101.47        T 1094=  102.66    T  1095= 105.27 T  1101=  100.45    T  1102=  100.85      T 1103= 101.79      T 1104= 103.28        T 1111=  100.85    T  1112= 102.12 T  1113=  104.65    T  1114=  107.82      T 1115= 113.59      T 1121= 101.59        T 1122=  104.35    T  1123= 109.90 T  1124=  116.97    T  1125=  126.32      T 1126= 131.79      T 2001= 136.26        T 2011=  135.29    T  2021= 129.55 T  2031=  130.02    T  2032=  130.25      T 2041= 130.78      T 2051= 131.12        T 2061=  131.53    T  2071= 132.18 T  2081=  134.92    T  2121=  135.85      T 2202= 139.02      T 2212= 137.81        T 2282=  138.68    T  2322= 141.12 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER T  1055=  110.53    T  1056=  111.95      T 1057= 115.36      T 2201= 138.63        T 2203=  140.43    T  2211= 137.58 T  2213=  137.82    T  2281=  138.38      T 2283= 138.63      T 2321= 140.38        T 2323=  143.70 HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER T      1=  100.00 SYSTEMS IMPROVED NUMERICAL DIFFERENCING ANALYZER WITH FLUID INTEGRATOR              PAGE    5 MODEL = WHOLE              HALF PACK w/7 55G Drums, One Drum Heat +100F w/o solar 8/12/97 STDSTL SINDA/FLUINT v3.1    Runtime: 7/8/98 9:51 SUBMODEL NAME = DRUMS CALCULATED                                ALLOWED MAX DIFF DELTA T PER ITER      DRLXCC(DRUMS    3740)= 2.441406E-03 VS. DRLXCA= 1.000000E-02 MAX ARITH DELTA T PER ITER    ARLXCC(            0)= 0.000000E+00 VS. ARLXCA= 1.000000E-02 MAX SYSTEM ENERGY BALANCE      EBALSC                = 2.541827E-02 VS. EBALSA
* ESUMIS        = 8.532490E-02 EBALSA= 1.000000E-02 ENERGY INTO AND OUT OF SYS    ESUMIS                = 8.53249          ESUMOS= 0.000000E+00 MAX NODAL ENERGY BALANCE      EBALNC(DRUMS    2413)= 2.466544E-03 VS. EBALNA= 0.000000E+00 NUMBER OF ITERATIONS          LOOPCT                =    507      VS. NLOOPS=    20000 PROBLEM TIME                  TIMEN                = 0.500000    VS. TIMEND= 3.00000 DIFFUSION NODES IN ASCENDING NODE NUMBER ORDER T  2403=  145.46    T  2404=  143.86      T 2413= 137.86      T 2414= 137.85        T 3300=  147.88    T  3302= 147.86 T  3304=  147.77    T  3306=  147.53      T 3308= 147.35      T 3312= 138.76        T 3314=  139.94    T  3316= 144.57 T  3318=  145.80    T  3322=  137.95      T 3324= 137.98      T 3326= 138.17        T 3328=  139.49    T  3332= 137.84 T  3334=  137.75    T  3336=  137.49      T 3338= 135.79      T 3340= 137.99        T 3342=  137.79    T  3344= 137.64 T  3346=  137.13    T  3348=  133.79      T 3400= 268.41      T 3402= 266.71        T 3404=  258.39    T  3406= 233.04 T  3408=  148.64    T  3412=  139.41      T 3414= 140.77      T 3416= 143.37        T 3418=  146.68    T  3422= 138.68 T  3424=  138.93    T  3426=  139.33      T 3428= 140.10      T 3432= 137.96        T 3434=  137.54    T  3436= 136.82 T  3438=  135.21    T  3440=  138.38      T 3442= 137.66      T 3444= 136.96        T 3446=  135.73    T  3448= 132.89 T  3500=  316.28    T  3502=  313.79      T 3504= 301.60      T 3506= 265.06        T 3508=  149.75    T  3512= 139.69 T  3514=  141.05    T  3516=  143.42      T 3518= 147.43      T 3522= 138.96        T 3524=  139.31    T  3526= 139.79 T  3528=  140.49    T  3532=  138.05      T 3534= 137.51      T 3536= 136.65        T 3538=  135.06    T  3540= 138.55 T  3542=  137.65    T  3544=  136.76      T 3546= 135.33      T 3548= 132.71        T 3600=  328.87    T  3602= 326.12 T  3604=  312.71    T  3606=  272.92      T 3608= 150.43      T 3612= 139.91        T 3614=  141.29    T  3616= 143.66 T  3618=  147.91    T  3622=  139.16      T 3624= 139.55      T 3626= 140.07        T 3628=  140.79    T  3632= 138.18 T  3634=  137.62    T  3636=  136.72      T 3638= 135.14      T 3640= 138.72        T 3642=  137.76    T  3644= 136.81 T  3646=  135.35    T  3648=  132.86      T 3700= 156.32      T 3702= 156.19        T 3704=  155.58    T  3706= 153.72 T  3708=  147.69    T  3712=  140.05      T 3714= 141.15      T 3716= 143.53        T 3718=  145.94    T  3722= 138.95 T  3724=  139.06    T  3726=  139.34      T 3728= 140.31      T 3732= 138.40        T 3734=  138.11    T  3736= 137.58 T  3738=  135.88    T  3740=  138.81      T 3742= 138.18      T 3744= 137.72        T 3746=  136.82    T  3748= 133.90 ARITHMETIC NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
HEATER NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
BOUNDARY NODES IN ASCENDING NODE NUMBER ORDER
                                                          ++NONE++
3.6.1-4
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 3.6.2      Thermal Model Details 3.6.2.1      Convection Coefficient Calculation Heat transfer coefficients from the OCA outer surface are calculated as follows. From Elements of Heat Transfer 1, the convective heat transfer coefficient, h, is:
k h = Nu        Btu/hr-in2-&#xba;F L
where k is the conductivity of gas at film temperature (Btu/hr-in-&#xba;F) and L is the effective length of the vertical surface or cylinder diameter for the horizontal surface.
The Nusselt number, Nu, for horizontally heated surfaces facing upward is:
Nu = 0.54(Gr Pr)1 4                                      for 105 < GrPr < 2x107 Nu = 0.14(Gr Pr)1 3                                      for 2x107 < GrPr < 3x1010 and, for horizontally heated surfaces facing downward:
Nu = 0.27(Gr Pr)1 4                                      for 3x105 < GrPr < 3x1010 The Nusselt number, Nu, for vertically heated surfaces is:
2 0.387(Gr Pr)1 6 Nu =  0.825 +                                          for 10-1 < GrPr < 1012
[
1 + ( 0 .492  Pr ) 9 16
                                                              ] 8 27 For both horizontally and vertically heated surfaces, the Grashof number, Gr, is:
gTL3 Gr =
2 where g is the gravitational acceleration constant (in/s2),  is the gas coefficient of thermal expansion (&#xba;F-1), where  = (Tabs)-1 for an ideal gas, T is the differential temperature (&#xba;F), where T = lTwall - Tl,  is the kinematic viscosity of gas at the film temperature (in2/s), and Pr is the Prandtl number. Note that k, Gr, and Pr are each a function of air temperature per Table 3.2-3.
3.6.2.2      Aluminum Honeycomb Conductivity Calculation The thermal conductivity of aluminum honeycomb reported by Hexcel in TSB-120 2 provides little or no supporting information for how those values were obtained, or for what honeycomb orientation they are valid. The Satellite Thermal Control Handbook 3 provides a computationally derived method for determining the effective thermal conductivity of honeycomb structures based on cell size, material thickness, and orientation. Thermal conductivity calculated by this 1
Y. Bayazitoglu and M. Ozisik, Elements of Heat Transfer, McGraw-Hill Publishing, New York, 1988, pp180-181.
2 Hexcel, Mechanical Properties of Hexcel Honeycomb Materials, TSB-120 (Technical Service Bulletin 120), 1992.
3 D. G. Gilmore, Editor, Satellite Thermal Control Handbook, The Aerospace Corporation Press, El Segundo, CA, 1994.
3.6.2-1
 
HalfPACT Safety Analysis Report                                                            Rev. 9, August 2022 method is lower than the value reported by Hexcel, and is therefore conservatively used in the thermal model. The following figure, derived from the Satellite Thermal Control Handbook, serves to illustrate the dimensional parameters considered.
The effective conductivity for the x, y and z directions (W, L and T directions, respectively, on above drawing) are calculated as follows:
3 k Al        k          8k kx =          , k y = Al , k z = Al 2 S              S          3 S Note that for the HalfPACT calculations, ky and kz represent axial and radial conductivity, respectively.
The aluminum honeycomb spacers used in the ICV torispherical heads have a foil thickness, , of 0.003 inches, and a nominal cell dimension, S, of 0.375 inches. Therefore, kx = (0.0120)kAl, ky = (0.0080)kAl, kz = (0.0213)kAl From Section 515.29, Page 2, of Properties of Solids, Thermal Conductivity, Metallic Materials 4, the thermal conductivity of 5052 aluminum, kAl, is 79.7 Btu/hr-ft-&#xba;F at 68 &#xba;F, 82.2 Btu/hr-ft-&#xba;F at 212
&#xba;F, and 100.0 Btu/hr-ft-&#xba;F at 752 &#xba;F. Table 3.6.2-1 summarizes the thermal conductivities for the aluminum honeycomb used in the analyses. Thermal conductivities are provided at -40 &#xba;F and 1,500 &#xba;F are provided to ensure computational stability.
Table 3.6.2 Effective Thermal Conductivity of Aluminum Honeycomb Temperature, &#xba;F                        kradial, Btu/hr-in-&#xba;F                    kaxial, Btu/hr-in-&#xba;F
              -40                                      0.053                                  0.142 68                                    0.053                                  0.142 212                                      0.055                                  0.146 752                                      0.067                                  0.178 1,500                                      0.067                                  0.178 4
General Electric, Properties of Solids, Thermal Conductivity, Metallic Materials, Heat Transfer Division, July 1974.
3.6.2-2
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 3.6.2.3      Polyethylene Plastic Wrap Transmittance Calculation As many as 18 layers of the optional, 0.002-inch thick, polyethylene plastic wrap is used to restrain the payload drums during transport. Data on the transmittance of polyethylene is available from Figure 659 of Thermophysical Properties of Matter 5. Assuming a plastic wrap temperature of 200 &#xba;F to 250 &#xba;F, Curves 1 through 4 from Figure 659 of Thermophysical Properties of Matter are applicable. Wiens displacement law states:
max T =5215.6 &#xb5;m-&#xba;R Thus, at 250 &#xba;F, the wavelength of maximum intensity is:
5215.6 max =            =7.436 &#xb5;m (250 + 460)
The number of wraps is of secondary importance to the overall transmittance, since the first few layers perform essentially all of the filtering. The maximum monochromatic radiation is near 10
&#xb5;m, and since the low end of the transmittance curves is near  = 0.75, an overall transmittance of 0.75 is applicable.
From Case 1 (see the computer analysis results in Appendix 3.6.1.1, Seven 55-Gallon Drum Payload with 100 &#xba;F Ambient and Full Solar Loading, Uniformly Distributed Decay Heat Load (Case 1)), the maximum temperature differential between the drum surface and the ICV wall surface is between drum node 3348 and ICV node 2032. With drum node 3348 at 153.3 &#xba;F, and ICV node 2032 at 150.2 &#xba;F, the temperature difference is only 3.1 &#xba;F. Extracting heat flow at these nodes from the computer run, approximately 14% of the decay heat is transferred from the drum surface to the ICV wall via radiative heat transfer. Therefore, the inclusion of the 0.75 transmittance would have a negligible impact on maximum drum temperatures.
5 Y.S. Touloukian and C.Y. Ho, Editors, Thermophysical Properties of Matter, Thermophysical Properties Research Center (TPRC) Data Series, Purdue University, 1970, IFI/Plenum, New York.
3.6.2-3
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
3.6.2-4
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 4.0 CONTAINMENT 4.1 Containment Boundary 4.1.1 Containment Vessel One level of containment and an optional secondary level of confinement are established within the HalfPACT package. In general, the containment and confinement vessels are constructed primarily of ASTM A240, Type 304, austenitic stainless steel. The exceptions to the use of ASTM A240, Type 304, stainless steel are so noted in the following detailed descriptions.
4.1.1.1    Outer Confinement Assembly (Secondary Confinement)
The confinement boundary of the outer confinement vessel (OCV), provided as part of the outer confinement assembly (OCA), consists of the inner stainless steel vessel comprised of a mating lid and body, plus the uppermost (innermost) of two optional main O-ring seals between them.
In addition, the confinement boundary includes an ASTM B16, Alloy 360, brass OCV vent port plug with a mating optional O-ring seal. A more detailed description of the OCV confinement boundary is provided in Section 1.2.1.1.1, Outer Confinement Assembly (OCA), and in Appendix 1.3.1, Packaging General Arrangement Drawings.
The non-stainless steel components utilized in the OCV confinement boundary are the optional upper O-ring seal, the brass vent port plug, and the optional O-ring seal on the vent port plug.
4.1.1.2    Inner Containment Vessel (Primary Containment)
The containment boundary of the Inner Containment Vessel (ICV) consists of a stainless steel vessel comprised of a mating lid and body, plus the uppermost (innermost) of the two main O-ring seals between them. In addition, the containment boundary includes an ASTM B16, Alloy 360, brass ICV outer vent port plug with a mating butyl O-ring seal. A more detailed description of the ICV containment boundary is provided in Section 1.2.1.1.2, Inner Containment Vessel (ICV) Assembly, and in Appendix 1.3.1, Packaging General Arrangement Drawings.
The non-stainless steel components utilized in the ICV containment boundary are the upper (inner) butyl O-ring seal, the brass outer vent port plug, and the butyl O-ring seal on the vent port plug.
4.1.2 Containment Penetrations The only containment and confinement boundary penetrations into the ICV containment and OCV confinement vessels are the lids themselves, and their corresponding vent ports. Each penetration is designed to demonstrate leaktight sealing integrity, i.e., a leakage rate not to exceed 1 x 10-7 standard cubic centimeters per second (scc/sec), air, as defined in ANSI N14.5 1.
1 ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
4.1-1
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 4.1.3 Seals and Welds 4.1.3.1      Seals Seals affecting containment and confinement are described above. A summary of seal testing prior to first use, during routine maintenance, and upon assembly for transportation is as follows.
4.1.3.1.1      Fabrication Leakage Rate Tests During fabrication and following the pressure testing per Section 8.1.2.2, Pressure Testing, the ICV (primary containment) shall be leakage rate tested as delineated in Section 8.1.3, Fabrication Leakage Rate Tests. The fabrication leakage rate tests are consistent with the guidelines of Section 7.3 of ANSI N14.5. This leakage rate test verifies the containment integrity of the HalfPACT packages ICV to a leakage rate not to exceed 1 x 10-7 scc/sec, air.
The OCV (secondary confinement) may optionally be leakage rate tested as delineated in Section 8.1.3, Fabrication Leakage Rate Tests.
4.1.3.1.2      Maintenance/Periodic Leakage Rate Tests Annually, or at the time of damaged containment seal replacement or sealing surface repair, the ICV O-ring containment seals shall be leakage rate tested as delineated in Section 8.2.2, Maintenance/Periodic Leakage Rate Tests. The maintenance/periodic leakage rate tests are consistent with the guidelines of Sections 7.4 and 7.5 of ANSI N14.5. This test verifies the sealing integrity of the HalfPACT packages ICV lid and vent port containment seals to a leakage rate not to exceed 1 x 10-7 scc/sec, air. The OCV O-ring confinement seals may optionally be leakage rate tested as delineated in Section 8.2.2, Maintenance/Periodic Leakage Rate Tests.
4.1.3.1.3      Preshipment Leakage Rate Tests Prior to shipment of the loaded HalfPACT package, the main O-ring seal and outer vent port plug O-ring seal for the ICV shall be leakage rate tested per Section 7.4, Preshipment Leakage Rate Test. The preshipment leakage rate tests are consistent with the guidelines of Section 7.6 of ANSI N14.5. This test verifies the sealing integrity of the HalfPACT packages ICV lid and vent port containment seals to a leakage rate sensitivity of 1 x 10-3 scc/sec, air, or less. The main O-ring seal and vent port plug O-ring seal for the OCV may optionally be leakage rate tested per Section 7.4, Preshipment Leakage Rate Test.
As an option, the maintenance/periodic leakage rate tests, delineated in Section 8.2.2, Maintenance/Periodic Leakage Rate Tests, may be performed in lieu of the preshipment leakage rate tests.
4.1.3.2      Welds All containment vessel body welds are full penetration welds that have been radiographed to ensure structural and containment integrity. Non-radiographed, safety related welds such as those that attach the ICV vent port insert to its containment shell are examined using liquid penetrant testing on the final pass or both the root and final passes, as applicable. All containment (and, optionally, confinement) boundary welds are confirmed to be leaktight as delineated in Section 8.1.3, Fabrication Leakage Rate Tests.
4.1-2
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 4.1.4      Closure 4.1.4.1      Outer Confinement Assembly (OCA) Closure With reference to Figure 1.1-1 and Figure 1.1-2 in Chapter 1.0, General Information, the OCA lid is secured to the OCA body via an OCV locking ring assembly located at the outer diameter of the OCV upper (lid) and lower (body) seal flanges. The upper end of the OCV locking ring is a continuous ring that mates with the OCV upper seal flange (also a continuous ring). The lower end of the OCV locking ring is comprised of 18 tabs that mate with a corresponding set of 18 tabs on the OCV lower seal flange. The OCV locking ring and OCV upper seal flange are an assembly that normally does not disassemble.
Figure 1.2-1 from Section 1.2, Package Description, illustrates ICV/OCA lid installation in five steps:
: 1. As an option, lightly lubricate the main O-ring seals with vacuum grease and install the main O-ring seals into the O-ring seal grooves located in the OCV lower seal flange.
: 2. Using external alignment stripes as a guide, align the OCA lids OCV locking ring tabs with the OCV lower seal flange tab spaces.
: 3. Install the OCA lid; if necessary, evacuate the OCV cavity through the OCV vent port to fully seat the OCA lid and allow free movement of the OCV locking ring.
: 4. Rotate the OCV locking ring to the locked position, again using external alignment stripes as a guide. The locked position aligns the OCV locking rings tabs with the OCV lower seal flanges tabs. A locking Z-flange is bolted to the bottom end of the OCV locking ring and extends radially outward to the exterior of the HalfPACT package. The exterior flange of the locking Z-flange is attached to an outer thermal shield. This Z-flange/thermal shield assembly allows external operation of the OCV locking ring.
: 5. Install six 1/2-inch diameter lock bolts (socket head cap screws) through the outer thermal shield and into the exterior surface of the OCA to secure the OCV locking ring assembly in the locked position.
4.1.4.2      Inner Containment Vessel (ICV) Closure With the exception of the locking Z-flange/outer thermal shield assembly, required use of main O-ring seals, and the use of three rather than six locking ring lock bolts, ICV lid installation is identical to OCA lid installation as described in Section 4.1.4.1, Outer Confinement Assembly (OCA) Closure.
4.1-3
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
4.1-4
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 4.2 Containment Requirements for Normal Conditions of Transport 4.2.1 Containment of Radioactive Material The results of the normal conditions of transport (NCT) structural and thermal evaluations performed in Section 2.6, Normal Conditions of Transport, and Section 3.4, Thermal Evaluation for Normal Conditions of Transport, respectively, and the results of the full-scale, structural testing presented in Appendix 2.10.3, Certification Tests, verify that there will be no release of radioactive materials per the leaktight definition of ANSI N14.5 1 under any of the NCT tests described in 10 CFR &sect;71.71 2.
4.2.2 Pressurization of Containment Vessel The maximum normal operating pressure (MNOP) of both the OCV and ICV is 50 psig per Section 3.4.4, Maximum Internal Pressure. The design pressure of both the OCV and ICV is 50 psig. Based on the structural evaluations performed in Chapter 2.0, Structural Evaluation, pressure increases to 50 psig will not reduce the effectiveness of the HalfPACT package to maintain containment integrity per Section 4.2.1, Containment of Radioactive Material.
4.2.3 Containment Criterion At the completion of fabrication, the ICV shall be leakage rate tested as described in Section 4.1.3.1.1, Fabrication Leakage Rate Tests. For annual maintenance, the ICV shall be leakage rate tested as described in Section 4.1.3.1.2, Maintenance/Periodic Leakage Rate Tests. In addition, at the time of seal replacement if other than during routine maintenance (e.g., if damage during assembly necessitates seal replacement), maintenance/ periodic leakage rate testing shall be performed for that seal. For verification of proper assembly prior to shipment, the ICV shall be leakage rate tested as described in Section 4.1.3.1.3, Preshipment Leakage Rate Tests. The above delineated criterion may optionally be applied to the OCV confinement components.
1 ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
2 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
4.2-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
4.2-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 4.3 Containment Requirements for Hypothetical Accident Conditions 4.3.1 Fission Gas Products There are no fission gas products in the HalfPACT package payload.
4.3.2 Containment of Radioactive Material The results of the hypothetical accident condition (HAC) structural and thermal evaluations performed in Section 2.7, Hypothetical Accident Conditions, and Section 3.5, Thermal Evaluation for Hypothetical Accident Conditions, respectively, and the results of the full-scale, structural and thermal testing presented in Appendix 2.10.3, Certification Tests, verify that there will be no release of radioactive materials per the leaktight definition of ANSI N14.5 1 under any of the HAC tests described in 10 CFR &sect;71.73 2.
4.3.3 Containment Criterion The HalfPACT package has been designed, and has been verified by leakage rate testing both prior to and following structural and thermal certification testing as presented in Appendix 2.10.3, Certification Tests, to meet the leaktight definition of ANSI N14.5.
1 ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
2 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
4.3-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
4.3-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 4.4 Special Requirements 4.4.1 Plutonium Shipments The HalfPACT package was designed and structurally and thermally tested as a Type B(U),
double containment package meeting the requirements of 10 CFR &sect;71.63 1 for plutonium shipments. With the revised designation of the outer confinement vessel (OCV) as a secondary confinement boundary when its optional O-ring seals are utilized, the HalfPACT package is a Type B(U), single containment package meeting the requirements of 10 CFR &sect;71.63 for plutonium shipments. Both the inner containment vessel (ICV) and OCV are shown on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings, and described in Section 4.1.1.1, Outer Confinement Assembly (Secondary Confinement), and Section 4.1.1.2, Inner Containment Vessel (Primary Containment). Further, the HalfPACT package has been designed, and has been verified by leakage rate testing both prior to and following structural and thermal certification testing as presented in Appendix 2.10.3, Certification Tests, to meet the leaktight definition of ANSI N14.5. 2 4.4.2 Interchangeability The HalfPACT package is designed and fabricated so that both the OCV lid assembly and the ICV lid assembly are interchangeable between OCV body assemblies and ICV body assemblies, respectively. Each combination of a particular ICV lid assembly and ICV body assembly becomes a containment system that shall be maintained in accordance with Section 4.1.3.1.2, Maintenance/Periodic Leakage Rate Tests, and used in accordance with Section 4.1.3.1.3, Preshipment Leakage Rate Tests. When the ICV interchangeability option has been exercised, newly combining a lid and a body, measure the axial play per the requirements of Section 8.2.3.3.2.3, Axial Play, to determine acceptability. Each combination of a particular OCV lid assembly and OCV body assembly becomes a confinement system that may optionally be maintained in accordance with Section 4.1.3.1.2, Maintenance/Periodic Leakage Rate Tests, and used in accordance with Section 4.1.3.1.3, Preshipment Leakage Rate Tests. When the OCV interchangeability option has been exercised, newly combining a lid and a body, optionally measure the axial play per the requirements of Section 8.2.3.3.2.3, Axial Play, to determine acceptability.
1 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
4.4-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
4.4-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 5.0 SHIELDING EVALUATION The compliance evaluations of the HalfPACT packaging with respect to the dose rate limits established by 10 CFR &sect;71.47(a) 1 for normal conditions of transport (NCT) or 10 CFR
&sect;71.51(a)(2) for hypothetical accident conditions (HAC) are based on two categories. The first category is for evaluations of Generic payload (55-gallon drums, 85-gallon drums, 100-gallon drums, and Standard Waste Boxes (SWB)), Criticality Control Overpacks (CCO), 6-in. Standard Pipe Overpacks (6PO), 12-in. Standard Pipe Overpacks (12PO), and SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2 Shielded Containers (SCs) presented in Chapter 5.0 of the TRUPACT-II Safety Analysis Report 2. The second category is for evaluations of the S100, S200, and S300 Pipe Overpacks presented in Appendix 4.2, 4.3, and 4.4 of the CH-TRU Payload Appendices. 3 The evaluations referenced above demonstrate that the regulatory dose rate requirements are satisfied when limiting the activity of the HalfPACT package in accordance with the methodology defined Section 3.3 of the CH-TRAMPAC. 4 1
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 U.S. Department of Energy (DOE), TRUPACT-II Shipping Package Safety Analysis Report, USNRC Certificate of Compliance 71-9218, U.S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico 3
U.S. Department of Energy (DOE), CH-TRU Payload Appendices, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
4 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
5-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
5-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022
 
==6.0 CRITICALITY EVALUATION==
 
The following analyses demonstrate that the HalfPACT package complies with the requirements of 10 CFR &sect;71.55 1 and &sect;71.59. The analyses show that the criticality requirements are satisfied when limiting the payload containers and the HalfPACT package to fissile gram equivalent (FGE) of Pu-239 limits given in Table 6.1-1 and Table 6.1-2, respectively for the payloads described in the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) 2. In summary, Case A is applicable to waste that is not machine compacted and contains less than or equal to 1% by weight quantities of special reflector materials and Case B is applicable to waste that is not machine compacted and contains greater than 1% by weight quantities of special reflector materials. For Case A, package limits were calculated for various Pu-240 contents in the package. Case C is applicable to machine compacted waste that contains less than or equal to 1% by weight quantities of special reflector materials. Case D is specifically applicable to machine compacted waste in the form of puck drums overpacked in 55-, 85-, or 100-gallon drums with less than or equal to 1% by weight quantities of special reflector materials. Case E is applicable to waste in the standard, S100, S200, and S300 pipe overpacks with less than or equal to 1% by weight quantities of special reflector materials and Case F is applicable to waste that is not machine compacted in the standard, S100, S200, and S300 pipe overpacks with greater than 1% by weight quantities of special reflector materials.
Case G is applicable to waste that is not machine compacted in shielded containers (i.e.,
SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2) with less than or equal to 1% by weight quantities of special reflector materials. Case H is applicable to machine compacted waste in shielded containers (i.e., SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2) with less than or equal to 1% by weight quantities of special reflector materials. Case I is applicable to waste in the criticality control overpack (CCO) with less than or equal to 1% by weight quantities of special reflector materials, provided that machine compacted waste contents are additionally limited to a maximum of 2,000 grams of plastic per CCO. However, if the quantity of special reflector material in the payload is greater than 1% by weight but the form of the payload is such that the thickness and/or packing fraction of the special reflector material is less than the reference poly/water reflector or the special reflector material (excluding beryllium in non-pipe overpack configurations) is mechanically or chemically bound to the fissile material, then Case A and Case E limits apply in lieu of Case B and Case F limits, respectively. Also, Case G and Case I limits are applicable to waste that is not machine compacted with greater than 1% by weight quantities of special reflectors in the above stated forms. Similarly, Case C, Case D, Case E, Case H, and Case I limits are applicable to machine compacted waste with greater than 1% by weight quantities of special reflectors in the above stated forms.
1 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
6.1-1
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 The criticality evaluations for Cases E and F are presented in Appendices 4.1, 4.2, 4.3, and 4.4 in the CH-TRU Payload Appendices 1, Cases G and H are presented in Appendices 4.5, 4.7, 4.8, 4.9, and 4.10 of the CH-TRU Payload Appendices, and Case I is presented in Appendix 4.6 of the CH-TRU Payload Appendices whereas the analyses for Cases A through D are presented in this chapter. Based on an unlimited array of undamaged or damaged HalfPACT packages, the Criticality Safety Index (CSI), per 10 CFR &sect;71.59, is 0.0.
6.1 Discussion and Results The criticality analyses presented herein are identical to the analyses presented in Chapter 6.0, Criticality Evaluation, of the TRUPACT-II Shipping Package Safety Analysis Report 2. Since the height of a HalfPACT package is 30 inches shorter than a TRUPACT-II package, resulting in a closer axial packaging in the infinite arrays, the criticality analyses utilizing the HalfPACT package geometry are considered conservative for Cases A through D. A comprehensive description of the HalfPACT packaging is provided in Section 1.2, Package Description, and in the packaging drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
For the contents of the HalfPACT package specified in Section 6.2, Package Contents, no special features are required to maintain criticality safety for any number of HalfPACT packages for both normal conditions of transport (NCT) and hypothetical accident conditions (HAC). The presence and location of the stainless steel, inner containment vessel and outer confinement vessel shells (ICV and OCV, respectively) and outer confinement assembly (OCA) outer shell are all that are required to maintain criticality safety.
The criteria for ensuring that a package (or package array) is safely subcritical is:
ks = keff + 2 < USL where the quantity ks is the multiplication factor computed for a given configuration plus twice the uncertainty in the computed result, . This quantity is computed and reported in order to permit a direct comparison of results against the upper subcriticality limit, USL, determined in Section 6.5, Critical Benchmark Experiments. The USL is determined on the basis of a benchmark analysis and incorporates the combined effects of code computational bias, the uncertainty in the bias based on both experimental and computational uncertainties, and an administrative margin. Further discussion regarding the USL is provided in Chapter 4, Determination of Bias and Subcritical Limits, of NUREG/CR-6361 3.
The results of the criticality calculations are summarized in Table 6.1-3. Calculations performed for Case A for a HalfPACT single unit and infinite arrays of damaged HalfPACT packages indicate that the maximum reactivity of the package arrays are essentially the same as that of the NCT single-unit to within the calculated uncertainty of the Monte Carlo analysis. This occurs because:
1 U.S. Department of Energy (DOE), CH-TRU Payload Appendices, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
2 U.S. Department of Energy (DOE), TRUPACT-II Shipping Package Safety Analysis Report, USNRC Certificate of Compliance 71-9218, U.S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico.
3 J. J. Lichtenwalter, S. M. Bowman, M. D. DeHart, C. M. Hopper, Criticality Benchmark Guide for Light-Water-Reactor Fuel in Transportation and Storage Packages, NUREG/CR-6361, ORNL/TM-13211, March 1997.
6.1-2
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022
* When the ICV and OCA regions are filled with reflecting material, the size of these regions allows the presence of enough material to isolate the fissile material region of each HalfPACT packages from each other, and
* When the fissile material region of each damaged or undamaged HalfPACT package is unreflected, interaction among HalfPACT packages is maximized. However, interactive effects are not as great as the effect of full reflection.
As discussed below, all ks values are less than the USL of 0.9382. For all cases, the modeled conditions are considered to be extremely conservative, nevertheless, they provide an upper limit on ks. Therefore, the requirements of 10 CFR &sect;71.55 are met when the contents of a single HalfPACT package are limited in accordance with Table 6.1-1 and Table 6.1-2. The application of these limits to the HalfPACT payload described in the CH-TRAMPAC 4 is discussed, in summary, in Section 6.4.3.5, Applicable Criticality Limits for CH-TRU Waste.
Infinite arrays of both damaged and undamaged HalfPACT packages, as defined in Section 6.3.4, Array Models, are also safely subcritical (ks < USL). The post-accident geometry used in the model of the damaged HalfPACT packages conservatively bounds the damage experienced from certification testing described in Appendix 2.10.3, Certification Tests. Based on the results of the HAC 30-foot drops, the criticality model conservatively assumes that the OCA outer shell is deformed inward on the side, top, and bottom to a distance of 5 inches from the OCV. Further, the criticality model conservatively models the region between the ICV and the OCA as containing a mixture of 25% polyethylene, 74% water and 1% beryllium in all bounding cases to bound the presence of polyurethane foam in this region. After the HAC thermal event (fire), actual post-test measurements show 3 inches of foam, minimum, remains in impact regions, and 5 inches, minimum, remains elsewhere.
For an infinite array of damaged HalfPACT packages, the maximum calculated ks values for each case occurred for optimal internal moderation and maximum reflection within the ICV, OCA and interspersed regions. Of all calculations performed and summarized in Table 6.1-3, the maximum neutron multiplication factor, adjusted for code bias and uncertainty, of ks =
0.9359 occurs in Case A at the 360 FGE limit with 15 g of Pu-240 for an infinite array of HAC packages when optimally moderated and reflected. All results are detailed in Section 6.4.3, Criticality Results. As with the single-unit cases, the calculations contain conservatism in the geometry and material assumptions (as identified in Section 6.2, Package Contents, and Section 6.4.2, Fuel Loading or Other Contents Loading Optimization). At maximum reflection, the packages in the array are isolated from each other. An investigation of array reactivity when array interaction effects become significant as a result of decreased reflector volume fraction is provided in Section 6.4.3.2, Criticality Results for Infinite Arrays of HalfPACT Packages.
Therefore, the requirements of 10 CFR &sect;71.59 are met as arrays of HalfPACT packages will remain subcritical when the contents of a single HalfPACT package is limited as indicated in Table 6.1-1 and Table 6.1-2. Furthermore, a CSI of zero (0.0) is justified.
4 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
6.1-3
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Table 6.1 Fissile Material Limit per Payload Container Payload          Fissile Material Limit per Payload Container (Pu-239 FGE)
Configura
    -tion      Case    Case      Case      Case    Case    Case Case    Case  Case A      B        C          D        E      F    G        H      I 55-gallon 325      100      250      200        -        -    -      -      -
drums Pipe
                  -        -        -        -      200    140    -      -      -
overpacks SWB        325      100      250        -        -        -    -      -      -
85-gallon 325      100      250      200        -        -    -      -      -
drums 100-gallon 325      100      250      200        -        -    -      -      -
drums Shielded
                  -        -        -        -        -        -  325      245    -
containers CCOs          -        -        -        -        -        -    -      -    380 Note:
 
The FGE limits in Table 6.1-2 apply if crediting Pu-240 content.
Table 6.1 Fissile Material Limit per HalfPACT Package Minimum Pu-240          Fissile Material Limit per HalfPACT Package (Pu-239 FGE)
Content in      Case    Case      Case      Case    Case    Case Case    Case  Case A        B        C          D        E      F    G        H      I Package 0g        325      100      250      325      1400    980  325      245  2660 5g        340        -        -        -        -      -    -        -      -
15 g      360        -        -        -        -      -    -        -      -
25 g      380        -        -        -        -      -    -        -      -
6.1-4
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Table 6.1 Summary of Criticality Analysis Results Case A    Case B      Case C        Case D Normal Conditions of Transport (NCT)
Number of undamaged packages calculated to be subcritical Single Unit Maximum ks            0.9339      Same as HAC Infinite Array ks Infinite Array Maximum ks                  Same as HAC Infinite Array ks Hypothetical Accident Conditions (HAC)
Number of damaged packages calculated to be subcritical Single Unit Maximum ks (0 g Pu-240)      0.9331      Same as HAC Infinite Array ks Infinite Array Maximum ks (0 g Pu-240)    0.9331    0.9184      0.9345        0.9349 Infinite Array Maximum ks (with 0.9359        -            -            -
Pu-240)
Upper Subcriticality Limit (USL)                        0.9382 6.1-5
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
6.1-6
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 6.2 Package Contents The payload cavity of a HalfPACT package can accommodate seven 55-gallon drums, four 85-gallon drums, three 100-gallon drums, or one standard waste boxes (SWB). Different fissile gram equivalent (FGE) limits are available depending on the contents of the shipment as described in the subsections below.
The quantities of all fissile isotopes other than Pu-239 present in the CH-TRU waste material and other authorized payloads may be converted to a FGE using the conversion factors outlined in the CH-TRAMPAC 1. For modeling purposes, the package is assumed to contain Pu-239 at the FGE limit. The fissile composition of the payload will typically be as follows:
Nuclide                      Weight-Percent Pu-238                            Trace Pu-239                              93.0 Pu-240                              5.8 Pu-241                              0.4 Pu-242                            Trace Am-241                            Trace All other fissile isotopes                    0.7 Except for Cases A and D, no credit is taken for parasitic neutron absorption in CH-TRU waste materials and other authorized payloads, dunnage, or package contents. The entire contents of a HalfPACT package are conservatively modeled as an optimally moderated sphere of Pu-239 as determined by varying the H/Pu atom ratio. The size of the sphere is calculated based on the H/Pu ratio and the Pu mass. Case A takes credit for the presence of varying amounts of Pu-240 in the package, see Table 6.1-2. Case D is applicable to a very specific case where drums and their contents are machine compacted and then overpacked in 55-, 85-, or 100-gallon drums.
Due to the machine compaction, a higher polyethylene packing fraction is achieved and the fissile material is in a more reactive state within the pucks than if it reconfigured outside of the pucks and homogenized at a lower polyethylene packing fraction within the inner containment vessel (ICV). Thus, in this case, some of structural materials are credited and a cylindrical fissile region is modeled as discussed in Section 6.3.1.4, Case D Contents Model. The HalfPACT package meets the criticality safety requirements as specified in 10 CFR &sect;71.55 2 and
&sect;71.59, provided the limits specified in Table 6.1-1 and Table 6.1-2 are not exceeded.
1 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
2 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
6.2-1
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 6.2.1 Applicability of Case A Limit The Case A limit is applicable provided the contents are manually compacted (i.e., not machine compacted) and contain less than or equal to 1% by weight quantities of special reflector materials. These requirements drive the assumptions regarding the appropriately bounding moderator and reflector materials that are utilized in the analyses to bound the presence of all materials that are authorized for shipment under the Case A FGE limits. The contents model assumptions are provided in Section 6.3.1.1, Case A Contents Model.
The utilization of polyethylene as the bounding hydrogenous moderating material is justified by the SAIC-1322-001 3 study which concludes that polyethylene is the most reactive moderator that could credibly moderate CH-TRU waste in a pure form. A 25% volumetric packing fraction for polyethylene is used as a conservative value which is based on physical testing that bounds the packing fraction of polyethylene in manually compacted CH-TRU waste of 13.36% 4.
Materials that can credibly provide better than 25% polyethylene/75% water equivalent reflection are termed special reflectors and not authorized for shipment under Case A in quantities that exceed 1% by weight except in specific configurations discussed below. Based on the results from SAIC-1322-0013, Be, BeO, C, D2O, MgO and depleted U (0.3% 235U) are the only materials that can provide reflection equivalent to a 2 ft thickness of 25% polyethylene and 75% water mixture under any of the following conditions and are therefore the only materials considered as special reflectors:
* Less than 5/8 inch thick at 100% of theoretical density 5 in the form of large solids
* Less than 11/16 inch thick at 70% of theoretical density in the form of tightly-packed particulate solids
* Less than 20% packing fraction at 24 inches thick in the form of randomly dispersed particulate solids The utilization of 1% by volume beryllium in the reflector material filling the ICV bounds the presence of up to 1% by weight quantities of special reflectors that are randomly dispersed in the payload containers based on the volume of the ICV and the maximum allowed weight of the payload containers in the package. SAIC-1322-001 found that beryllium is the bounding special reflector as it provides the best reflection of the system resulting in the highest reactivity.
If the fissile material is bound to the special reflector material, these materials will provide moderation of the fissile material but will not be available to reflect the fissile region. The reference study, SAIC-1322-001, found that adding special reflector materials, with the exception of beryllium, to the fissile region reduced the reactivity of a single 325 FGE 25%
polyethylene/75% water reflected sphere. The moderating effect of heavy water was not studied, but the quantity of liquid allowed in the HalfPACT is limited such that heavy water would not be 3
Neeley, G. W., D. L. Newell, S. L. Larson, and R. J. Green, Reactivity Effects of Moderator and Reflector Materials on a Finite Plutonium System, SAIC-1322-001, Revision 1, Science Applications International Corporation, Oak Ridge, Tennessee, May 2004.
4 WP 08-PT.09, Test Plan to Determine the TRU Waste Polyethylene Packing Fraction, Washington TRU Solutions, LLC., Revision 0, June 2003.
5 Theoretical densities used in the study are 1.85 g/cm3 for Be, 2.69 g/cm3 for BeO, 2.1 g/cm3 for C, 1.1054 g/cm3 for D2O, 3.22 g/cm3 for MgO, and 19.05 g/cm3 for U.
6.2-2
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 present in greater than 1% by weight quantities. Thus, if the special reflector, excluding beryllium, is chemically or mechanically bound to the fissile material, Case A limits apply even in the presence of greater than 1% by weight quantities of the special reflector. Chemically bound means that the special reflector materials are chemically reacted with the fissile material such that the reflector materials and the fissile materials are chemically interacted and are stable.
Mechanically bound means the fissile material is mechanically bound to the reflector such that the reflector material will not disengage from the fissile material because it is topographically imbedded, topographically interlocked, or surface contaminated. A summary discussion of special reflectors is provided in Section 6.4.3.3.
6.2.2 Applicability of Case B Limit The Case B limit is applicable for contents containing greater than 1% by weight quantities of special reflector materials provided the contents are manually compacted (i.e., not machine compacted). These requirements drive the assumptions regarding the appropriately bounding moderator and reflector materials that are utilized in the analyses to bound the presence of all materials that are authorized for shipment under the Case B FGE limits. However, if the special reflector materials can be demonstrated to be in thicknesses and/or packing fractions that are less than the 25% polyethylene/ 75% water equivalent parameters given in Table 6.2-1, then Case A limits can be used. Note that equivalent thicknesses for Be and BeO are not given as, for thin reflectors of these materials, 100% packing fraction does not result in the highest reactivity and the equivalent thickness increases inversely with the packing fraction; thus, only a packing fraction comparison can be used for Be and BeO. The contents model assumptions are provided in Section 6.3.1.2, Case B Contents Model.
The utilization of polyethylene as the bounding hydrogenous moderating material at a 25%
packing fraction is consistent with the justification provided in Section 6.2.1, Applicability of Case A Limit. However, the fissile sphere is moderated with varying volume fractions of beryllium as beryllium was also found in SAIC-1322-001 to increase reactivity when significant quantities are included in the moderator. The use of a 100% dense thick Be reflector in the model bounds the presence of other special reflector materials.
6.2.3 Applicability of Case C Limit The Case C limit is applicable provided the contents are machine compacted and contain less than or equal to 1% by weight quantities of special reflector materials. These requirements drive the assumptions regarding the appropriately bounding moderator and reflector materials that are utilized in the analyses to bound the presence of all materials that are authorized for shipment under the Case C FGE limits. The contents model assumptions are provided in Section 6.3.1.3, Case C Contents Model.
The utilization of polyethylene as the bounding hydrogenous moderating material at a 100%
packing fraction is consistent with the justification provided in Section 6.2.1, Applicability of Case A Limit. Additionally, SAIC-1322-001 concluded no material, that could credibly moderate a fissile sphere in a pure form, resulted in a higher reactivity than the 100%
polyethylene moderated system. Thus, compared to Case A, the packing fraction of the moderator is the dominant factor that results in an increase in reactivity. The only inorganic material that increased reactivity when added to the fissile mixture was beryllium. The effect of more than 1% by weight quantities of beryllium in the moderator is studied under Case B as 6.2-3
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 beryllium is also the leading special reflector. The use of 99% polythylene and 1% beryllium (by volume) in the reflector region is an appropriately bounding reflector material as it is consistent with the moderator assumption and accounts for the less than or equal to 1% by weight quantities of special reflector materials allowed in the package.
Again, if the special reflector material, excluding beryllium, is chemically or mechanically bound to the fissile material or if the special reflector materials can be demonstrated to be in thicknesses and/or packing fractions that are less than the 25% polyethylene/ 75% water equivalent parameters given in Table 6.2-1, then Case C limits apply even in the presence of greater than 1% by weight quantities of the special reflector.
6.2.4 Applicability of Case D Limit The Case D limit is specifically applicable provided the contents are machine compacted in the form of puck drums overpacked in 55-, 85-, or 100-gallon drums with less than or equal to 1%
by weight quantities of special reflector materials and either of the following two controls: a) the packing fraction of polyethylene in the pucks is not greater than 70% or b) the separation between pucks in two axially adjacent overpack drums is maintained at greater than or equal to 0.50 inch through the use of a compacted puck drum spacer placed in the bottom of each overpack drum. These requirements drive the assumptions regarding the appropriately bounding moderator and reflector materials that are utilized in the analyses to bound the presence of all materials that are authorized for shipment under the Case D FGE limits. The contents model assumptions are provided in Section 6.3.1.4, Case D Contents Model.
The utilization of polyethylene as the bounding hydrogenous moderating material is consistent with the justification provided in Section 6.2.1, Applicability of Case A Limit. The use of a 70%
packing fraction is applicable provided that controls are implemented to ensure the packing fraction is limited during machine compaction. The use of 70% polyethylene, 29% water and 1% beryllium (by volume) in the reflector region is an appropriately bounding reflector material as it is consistent with the moderator assumption, again provided that controls are implemented to ensure the packing fraction is limited during machine compaction, and accounts for the less than or equal to 1% by weight quantities of special reflector materials allowed in the package.
Otherwise, the use of 99% polyethylene and 1% beryllium (by volume) in the reflector region is an appropriately bounding reflector material as it is consistent with the moderator assumption and accounts for the less than or equal to 1% by weight quantities of special reflector materials allowed in the package.
The compacted puck drum spacers have been demonstrated to maintain the minimum required axial spacing between pucks in axially adjacent overpack drums under Hypothetical Accident Conditions (HAC) and are described in Appendix 1.3.1, Packaging General Arrangement Drawings 6.
Again, if the special reflector material, excluding beryllium, is chemically or mechanically bound to the fissile material or if the special reflector materials can be demonstrated to be in thicknesses and/or packing fractions that are less than the 25% polyethylene/ 75% water 6
Packaging Technology, Inc., Test Report for Compacted Drums, TR-017, Revision 0, Packaging Technology, Inc.,
Tacoma, Washington, March 2004.
6.2-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 equivalent parameters given in Table 6.2-1, then Case D limits apply even in the presence of greater than 1% by weight quantities of the special reflector.
6.2.5 Applicability of Case E Limit The Case E limit is specifically applicable provided the contents are shipped in the standard, S100, S200, or S300 pipe overpacks with less than or equal to 1% by weight quantities of special reflector materials. Following the logic presented in Section 6.2.1, Applicability of Case A Limit, the presence of greater than 1% by weight quantities of special reflectors may be authorized for shipment under the Case E FGE limits if the fissile material is chemically and/or mechanically bound to the special reflector material. Due to the fact that beryllium was also specifically evaluated as a moderator in the pipe overpacks, this applies to all special reflector materials except heavy water, which is restricted based on the free liquid requirements for the package.
The contents model assumptions and analysis results are provided in Appendices 4.1, 4.2, 4.3, and 4.4 in the CH-TRU Payload Appendices.
6.2.6 Applicability of Case F Limit The Case F limit is specifically applicable provided the contents are manually compacted and shipped in the standard, S100, S200, or S300 pipe overpacks with greater than 1% by weight quantities of special reflector materials. However, if the special reflector materials can be demonstrated to be in thicknesses and/or packing fractions that are less than the 25%
polyethylene/ 75% water equivalent parameters given in Table 6.2-1, then Case E limits can be used. The contents model assumptions and analysis results are provided in Appendices 4.1, 4.2, 4.3, and 4.4 in the CH-TRU Payload Appendices.
6.2.7 Applicability of Case G Limit The Case G limit is specifically applicable provided the contents are manually compacted and shipped in shielded containers (i.e., SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2) with less than or equal to 1% by weight quantities of special reflector materials. However, if the quantity of special reflector material in the payload is greater than 1% by weight but the form of the payload is such that the thickness and/or packing fraction of the special reflector material is less than the reference poly/water reflector or the special reflector material (excluding beryllium) is mechanically or chemically bound to the fissile material, then the Case G limit is applicable to waste meeting these form requirements. The contents model assumptions and analysis results are provided in Appendices 4.5, 4.7, 4.8, 4.9, and 4.10 of the CH-TRU Payload Appendices.
6.2.8 Applicability of Case H Limit The Case H limit is specifically applicable provided the contents are machine compacted and shipped in shielded containers (i.e., SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2) with less than or equal to 1% by weight quantities of special reflector materials. However, if the quantity of special reflector material in the payload is greater than 1% by weight but the form of the payload is such that the thickness and/or packing fraction of the special reflector material is less than the reference poly/water reflector or the special reflector material (excluding beryllium) is mechanically or chemically bound to the fissile material, then the Case H limit is applicable to waste meeting these form requirements. The contents model assumptions and analysis results are provided in Appendices 4.5, 4.7, 4.8, 4.9, and 4.10 of the CH-TRU Payload Appendices.
6.2-5
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 6.2.9 Applicability of Case I Limit The Case I limit is specifically applicable provided the contents are shipped in CCOs with less than or equal to 1% by weight quantities of special reflector materials. However, if the quantity of special reflector material in the payload is greater than 1% by weight but the form of the payload is such that the thickness and/or packing fraction of the special reflector material is less than the reference poly/water reflector or the special reflector material (excluding beryllium) is mechanically or chemically bound to the fissile material, then the Case I limit is applicable to waste meeting these form requirements. Also, if the contents of a CCO are machine compacted then the plastic content of each CCO is limited to a maximum of 2,000 grams. The contents model assumptions and analysis results are provided in Appendix 4.6 of the CH-TRU Payload Appendices.
Table 6.2 Special Reflector Material Parameters that Achieve the Reactivity of a 25%/75% Polyethylene/Water Mixture Reflector Equivalent                Equivalent Thickness at 100%          Thickness at 70%        Equivalent Packing Special Reflector          of Theoretical            of Theoretical        Fraction at 24 in.
Material              Density (inch)            Density (inch)          Thickness (%)
Be                      N/A                      N/A                      7 BeO                      N/A                      N/A                      7 C                      0.18                      0.25                      9 D2O                      0.24                      0.27                    14 MgO                        0.26                      0.33                    15 U(Natural)                    0.08                      0.10                      1 U(0.6% 235U)                  0.14                      0.18                      1 U(0.5% 235U)                  0.18                      0.28                      2 U(0.4% 235U)                  0.33                      0.51                      3 U(0.3% 235U)                  0.56                      0.73                      5 6.2-6
 
HalfPACT Safety Analysis Report                                                        Rev. 9, August 2022 6.3 Model Specification Criticality calculations for the HalfPACT package are performed using the three-dimensional Monte Carlo computer code KENO-V.a 1, executed as part of the SCALE-PC v4.4a system 2 using the CSAS25 driver utility 3. Descriptions of the calculational models are given in Section 6.3.1, Contents Model, Section 6.3.2, Packaging Model, Section 6.3.3, Single-Unit Models, and Section 6.3.4, Array Models for all cases except Cases E, F, G, H, and I, which are discussed in Appendices 4.1, 4.2, 4.3, 4.4, 4.5, 4.6, 4.7, 4.8, 4.9, and 4.10 in the CH-TRU Payload Appendices 4. A summary of materials and atom densities that are used in the evaluation of the HalfPACT package is given in Section 6.3.5, Package Regional Densities.
The limiting mass of fissile material that may be transported in a single HalfPACT package is shown to provide adequate subcritical margin based on detailed KENO-V.a analyses. These calculations are performed for an optimally moderated single-unit model and an infinite array model of HalfPACT packages under both normal conditions of transport (NCT) and hypothetical accident conditions (HAC).
In all cases, the computational model consists of a contents model and a packaging model. The contents model conservatively represents the package contents, including all payload material, dunnage, fissile and moderating material. The packaging model represents the remaining structural materials comprising the HalfPACT packaging. The amount of moderating and reflecting material assumed to be present in the packaging model is varied to maximize reactivity.
6.3.1 Contents Model 6.3.1.1      Case A Contents Model The Case A contents are represented as an optimally moderated homogeneous sphere of Pu-239 and a 25% polyethylene and 75% water mixture (by volume). The radius of the model sphere is determined based on the modeled mass of plutonium and a specified H/Pu ratio. In each case, the H/Pu ratio is varied until the most reactive configuration is identified. FGE limits with 0 g, 5 g, 15 g, and 25 g Pu-240 present are calculated. When Pu-240 is present, the H/Pu ratio specified represents the H/Pu-239 atom ratio.
The remainder of the inner containment vessel (ICV) around the fissile sphere is filled with a 25% polyethylene, 74% water and 1% beryllium mixture (by volume). (Henceforward, unless otherwise specified, any reference to a polyethylene/water/beryllium mixture implies this particular 25% polyethylene, 74% water and 1% beryllium reflector composition.) The beryllium is added to 1
L. M. Petrie and N. F. Landers, KENO-V.a: An Improved Monte Carlo Criticality Program with Supergrouping, ORNL/NUREG/CSD-2/V2/R6, Volume 2, Section F11, March 2000.
2 Oak Ridge National Laboratory (ORNL), SCALE 4.4a: Modular Code System for Performing Standardized Computer Analyses for Licensing Evaluation for Workstations and Personal Computers, ORNL/NUREG/CSD-2/R6, March 2000.
3 N. F. Landers and L. M. Petrie, CSAS: Control Module for Enhanced Criticality Safety Analysis Sequences, ORNL/NUREG/CSD-2/V1/R6, Volume 1, Section C4, March 2000.
4 U.S. Department of Energy (DOE), CH-TRU Payload Appendices, U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
6.3-1
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 represent less than or equal to 1% by weight quantities of special reflectors that are allowed under the Case A loading limits. Based on the volume of the ICV and the maximum allowed weight of the payload containers in the package, modeling 1% beryllium by volume bounds the limit of 1% by weight. The reactivity effect of the addition of the 1% beryllium is shown to be very slight but positive. The KENO-V.a representation of the Case A single-unit contents model is illustrated in Figure 6.3-1.
The fissile sphere is nominally positioned in the center of the packaging model. In the array analyses, the effect of displacing the contents model within the packaging model in directions likely to increase reactivity is investigated. These array models are further described in Section 6.3.4, Array Models.
6.3.1.2      Case B Contents Model The fissile sphere composition in the Case B model is identical to the Case A fissile sphere composition. Unlimited quantities of beryllium in the fissile sphere are also studied but shown to reduce reactivity with the beryllium reflector. The difference in the Case A and B model lies in the reflector material filling the ICV. In the Case B model, the ICV is filled with beryllium and the volume fraction is varied from 10% to 100% to determine the point of maximum reactivity.
The KENO-V.a representation of the Case B single-unit contents model is illustrated in Figure 6.3-2.
6.3.1.3      Case C Contents Model The fissile sphere composition in the Case C model is moderated with 100% polyethylene and the reflector material filling the ICV is 99% polyethylene and 1% beryllium (by volume). The 1% beryllium in the ICV accounts for the reactivity increase provided by less than or equal to 1% by weight quantities of special reflector materials allowed in the package. The KENO-V.a representation of the Case C single-unit contents model is illustrated in Figure 6.3-3.
6.3.1.4      Case D Contents Model The Case D model is an extension of Case C applied to compacted puck drums overpacked in 55-, 85-, or 100-gallon drums where either the packing fraction of the contents is limited to 70%
through the use of process controls implemented during machine compaction or the separation between pucks in two axially adjacent overpack drums is maintained at greater than or equal to 0.50 inch through the use of a compacted puck drum spacer placed in the bottom of each overpack drum. The HalfPACT package can accommodate only a single tier of overpack drums whereas two tiers of overpack drums can be loaded into a TRUPACT-II package.
Reconfiguration of the fissile material from within each compacted puck is bounded by the Case A analysis since the reconfiguration would reduce the polyethylene packing fraction to below 25% as the material with the ICV is homogenized. Because of the axial separation between the overpack drums in a single tier and the 200 FGE limit per overpack drum, the most reactive scenario occurs in the TRUPACT-II package instead of in the HalfPACT package.
The most reactive, credible scenario consists of 325 FGE in two overpack drums that are stacked on top of one another. The fissile material will be separated by the steel of the compacted puck and overpack drum (or steel of the compacted puck drum spacer) and the polyethylene slip-sheet and reinforcing plate placed between the layers of overpack drums in the package. Thus, the contents model includes two cylinders of fissile material with 0.06-inch (0.1524-cm) thick steel 6.3-2
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 representing a conservative lower bound of the thickness of the steel in the lid of the lower puck and overpack drum (or steel in the compacted puck drum spacer), 0.15-inch (0.3810-cm) thick polyethylene representing 50% of the thickness of the slip-sheet and reinforcing plate, and another 0.06-inch (0.1524-cm) thick layer of steel representing a conservative lower bound of the thickness of steel in the bottom of the upper puck and overpack drum (or steel in the compacted puck drum spacer). Where applicable due to the use of a compacted puck drum spacer, the contents model includes an additional 0.50 inch of separation between the pucks, modeled filled with polyethylene or water to determine which is most reactive.
A 325 FGE fissile cylinder is modeled with an optimum height to diameter ratio of 0.924 to maximize reactivity and then split in two to represent the material in each overpack drum. The bottom half of the cylinder contains 200 FGE to represent the FGE limit in an overpack payload container and the top half of the cylinder contains 125 FGE. Modeling of the polyethylene in the slip-sheet and reinforcing plate is more reactive than modeling a water gap. The moderator is modeled either as 70% polyethylene and 30% water by volume or as 100% polyethylene. The material filling the ICV is either 70% polyethylene, 29% water and 1% beryllium or 99%
polyethylene and 1% beryllium. The 1% beryllium is included to account for less than or equal to 1% by weight quantities of special reflector materials. Filling the ICV with this material is conservative as the void space around the overpack drums is filled with the better reflecting polyethylene/water/beryllium or polyethylene/beryllium mixture. The results of calculations performed for Case A as discussed in Section 6.4.3.1.1, Case A Single Unit Results, showed that including 1% beryllium in the ICV region but not in the moderator was the most reactive placement and thus this configuration was modeled in the Case D calculations.
Even though only the TRUPACT-II package would allow the stacked drum configuration modeled, the packaging model representing the HalfPACT configuration is used to increase interaction between packages as discussed in the following section. The KENO-V.a representation of the Case D single-unit contents model is illustrated in Figure 6.3-4.
6.3.2 Packaging Model The criticality analyses presented herein are identical to the analyses presented in Chapter 6.0, Criticality Evaluation, of the TRUPACT-II Shipping Package Safety Analysis Report 5. With the exception of removing 30 inches from the packages height, all other post-test aspects (i.e., the packages configuration following free drop, puncture, and fire testing) between the HalfPACT and TRUPACT-II packages are essentially identical, especially with regard to the amount of remaining polyurethane foam. Also, the ICV region of the HalfPACT is large enough to provide full reflection of the fissile contents by the material contained therein. Therefore, due to the closer axial packaging in the infinite arrays, the criticality analyses utilizing the HalfPACT package geometry are considered conservative.
The packaging model represents the package structural materials, including the stainless steel shells and polyurethane foam. The model consists of nested, right circular cylindrical shells of Type 304 stainless steel (SS304). The right cylindrical geometry of the model conservatively neglects the torispherical shape of the ICV and OCV ends. The models inner shell represents 5
U.S. Department of Energy (DOE), TRUPACT-II Shipping Package Safety Analysis Report, USNRC Certificate of Compliance 71-9218, U.S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico.
6.3-3
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 the combined ICV and OCV components of the actual package. The narrow gap between the ICV and OCV shells is neglected, and the two components are modeled as a single shell of thickness 1/4 + 3/16 = 7/16 inches thick (1.1113 cm) on the side, and 1/4 + 1/4 = 1/2 inches thick (1.2700 cm) on the top and bottom. The outside radius of the cylindrical shell representing the combined ICV and OCV components is 38 inches (98.1869 cm), preserving the outer radius of OCV lid shell. The height of the cylinder, 44 inches (114.1413 cm), preserves the distance between the upper and lower aluminum honeycomb spacer assemblies within the ICV.
The second, outermost, cylindrical shell is 1/4 inches (0.6350 cm) thick, also of Type 304 stainless steel, and represents the outer confinement assembly (OCA) outer shell. The 3/8-inch thick portion of the OCA outer shell is conservatively ignored. Under NCT, the inside radius and inside height of the OCA outer shell are 46 inches (119.2213 cm) and 70 inches (177.8000 cm), respectively and the outer radius and height are 47 inches (119.8563 cm) and 701/2 inches (179.0700 cm), respectively. Under HAC, the inner radius and height of the OCA outer shell are based on the observed maximum deformation of the OCA following certification testing. At the conclusion of testing, approximately 5 inches of foam remained in the certification test units, except for local areas damaged by puncture bar drops. Hence, the inside of the OCA outer shell is set a distance of 5 inches (12.7000 cm) from the outside of the combined ICV and OCV shell and the 1/4-inch (0.6350-cm) thick OCA shell is modeled. Under both NCT and HAC, no credit is taken for parasitic neutron absorption properties of the polyurethane foam. Instead, the foam is replaced with the 25% polyethylene/74% water/1%
beryllium mixture used in Case A as a bounding reflecting material at a volume fraction that maximizes reactivity. Consideration is made for the structural properties of the foam by assuming that the inner cylindrical shell is maintained in its central position subsequent to all HAC tests. The KENO-V.a representation of single-unit undamaged and damaged HalfPACT packages are illustrated in Figure 6.3-5 and Figure 6.3-6, respectively.
The following simplifying assumptions tend to decrease the amount of structural material represented in the calculational model and decrease the center-to-center separation between HalfPACT packages in the array analyses and are, therefore, conservative.
* The domed surfaces of the torispherical heads are represented as flat surfaces and are positioned such that the overall height of the HalfPACT packaging is reduced.
* Under HAC, the thickness of the polyurethane foam region is reduced to 5 inches (12.7000 cm) throughout the entire OCA. In all cases, polyurethane foam is ignored and replaced with a polyethylene/water/beryllium mixture that fills the space at a volume fraction that optimizes reactivity.
6.3.3 Single-Unit Models Compliance with the requirements of 10 CFR &sect;71.55 6 is demonstrated by analyzing optimally moderated damaged and undamaged, single-unit HalfPACT packages. In the NCT single-unit model, the packaging and contents models described above are employed, and water is conservatively assumed to leak into the containment vessel to an extent that optimizes reactivity.
In Case A, the ICV is filled with the same polyethylene/water/beryllium mixture employed in the 6
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
6.3-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 contents model. In Case B, the ICV is filled with beryllium to represent the bounding special reflector material and in Case C, the ICV is filled with 99% polyethylene and 1% beryllium to represent machine compacted waste with no limitations on compaction. In Case D, the ICV is filled with either a mixture of 70% polyethylene, 29% water and 1% beryllium to represent machine compacted waste that is controlled to a 70% packing fraction or 99% polyethylene and 1% beryllium to represent machine compacted waste without packing fraction controls. In all cases, the area between the ICV/OCV shells and the OCA outer shell, simply termed the OCA, is filled with the 25% polyethylene/74% water/1% beryllium mixture employed in the ICV of Case A. This material is a bounding reflector for the low density foam normally present and the water that could leak into this area. These reflectors are assumed to occupy all void space within the packaging model at full theoretical density to maximize reflection of the fissile material and thus maximize reactivity. In addition, a 30-cm thick, close-fitting water reflector is placed around the outside of the packaging model to ensure full reflection is achieved.
The single-unit, HAC model is identical to the single-unit, NCT model, except the HAC packaging model assumes the models outer shell is displaced to within 5 inches (12.7000 cm) of the models inner shell.
6.3.4 Array Models Calculations are performed for an infinite array of damaged HalfPACT packages in a close-packed, square-pitch configuration. Triangular-pitched array configurations are not considered because the square-pitch array analyses demonstrate that array interaction effects are of minor consequence. A specularly reflective boundary condition is applied to all six faces of the unit cell defining the array configuration in order to represent an infinite array of HalfPACT packages. Displacement of the contents models within the ICV/OCV shell is considered in a manner that maximizes interaction of the fissile material between packages. Table 6.3-1 describes the configurations considered, with reference to KENO-generated plots that graphically illustrate each variation.
In the HAC array analysis, reflection of the fissile sphere by a 25% polyethylene/74% water/1%
beryllium mixture filling the ICV is considered in Case A. Case B considers beryllium filling the ICV as the bounding special reflector material and Case C considers full density polyethylene in the ICV to represent machine compacted waste. Case D is specific to machine compacted waste compacted in puck drums and then placed in 55-, 85-, or 100-gallon overpack drums with either a 70% packing fraction or puck separation controls modeled with either 70%
polyethylene/29% water/1% beryllium or 99% polyethylene/1% beryllium reflection filling the ICV, respectively. In all cases, water is considered between the packages in addition to a 25%
polyethylene/74% water/1% beryllium mixture in the OCA region. The volume fraction of all of these materials is varied to ensure the most reactive conditions are analyzed.
As a result of the explicit optimization of reactivity against interspersed moderator volume fraction, and because of the closer spacing between packages achieved in the accident geometry, the result of the HAC array calculations bound the NCT array cases.
6.3.5 Package Regional Densities A summary of all material compositions used in the HalfPACT package contents models is given in Table 6.3-2 for various H/Pu ratios. The parameters are computed based on SCALE Standard 6.3-5
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 Composition Library 7 values of a plutonium density of 19.84 g/cm3, a polyethylene density of 0.923 g/cm3 and a water density of 0.9982 g/cm3. The material used to represent the HalfPACT package is Type 304 stainless steel (SS304) with a density of 7.94 g/cm3 and carbon steel, with a density of 7.82 g/cm3, was used to represent the drum lid/bottom modeled in Case D. Number densities of the SS304 and carbon steel constituent nuclides are also based on the SCALE Standard Composition Library composition as presented in Table 6.3-3. The number densities for the various polyethylene, water and beryllium reflector mixtures are given in Table 6.3-4.
The SCALE standard composition identifier BEBOUND, nuclide identifier 4309, was used to model the beryllium reflector. The theoretical density of this material is 1.85 g/cm3 and the number density is 1.23621E-01 a/b-cm. The cross-section for BEBOUND is based on a beryllium metal whereas the cross-section for standard material BE is based on a free gas representation.
BEBOUND is also used to model beryllium in the benchmark cases discussed in Section 6.5, Critical Benchmark Experiments.
Table 6.3 Description of Contents Displacement in Array Models Replicated Variation        Array Size                          Description                    Reference 0                1x1x1              Contents centered in packaging model        Figure 6.3-7 1                2x2x2          All contents models displaced toward center    Figure 6.3-8 7
L.M. Petrie, P.B. Fox and K. Lucius, Standard Composition Library, ORNL/NUREG/CSD-2/V3/R6, Volume 3, Section M8, March 2000.
6.3-6
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Table 6.3 Fissile Contents Model Properties for Various H/Pu Ratios Pu Conc-                          Number Density H/Pu  entration        Pu              H                O              C Ratio    (g/l)        (a/b-cm)        (a/b-cm)        (a/b-cm)        (a/b-cm) 25% Polyethylene/75% Water Moderator used in Cases A and B 500    55.32      1.39374E-04    6.96904E-02      2.49700E-02    9.88730E-03 600    46.12      1.16199E-04    6.97198E-02      2.49802E-02    9.89131E-03 700    39.55      9.96359E-05    6.97470E-02      2.49901E-02    9.89517E-03 800    34.61      8.71898E-05    6.97634E-02      2.49958E-02    9.89720E-03 900    30.77      7.75285E-05    6.97805E-02      2.50019E-02    9.89996E-03 1,000    27.70      6.97733E-05    6.97894E-02      2.50040E-02    9.90030E-03 1,100    25.19      6.34398E-05    6.97967E-02      2.50067E-02    9.90185E-03 1,200    23.09      5.81675E-05    6.98011E-02      2.50093E-02    9.90271E-03 1,300    21.31      5.36925E-05    6.98150E-02      2.50137E-02    9.90445E-03 1,400    19.79      4.98652E-05    6.98177E-02      2.50142E-02    9.90461E-03 1,500    18.48      4.65401E-05    6.98231E-02      2.50171E-02    9.90571E-03 100% Polyethylene Moderator used in Cases C and D 500    62.76      1.58107E-04    7.90648E-02          ---        3.95315E-02 600    52.33      1.31834E-04    7.91113E-02          ---        3.95542E-02 700    44.87      1.13038E-04    7.91400E-02          ---        3.95699E-02 800    39.27      9.89296E-05    7.91566E-02          ---        3.95785E-02 900    34.92      8.79796E-05    7.91787E-02          ---        3.95891E-02 1,000    31.43      7.91773E-05    7.91959E-02          ---        3.95974E-02 1,100    28.58      7.20029E-05    7.92017E-02          ---        3.95998E-02 1,200    26.20      6.60091E-05    7.92166E-02          ---        3.96070E-02 1,300    24.19      6.09431E-05    7.92274E-02          ---        3.96122E-02 70% Polyethylene/30% Water Moderator used in Case D 500    59.79      1.50619E-04    7.53181E-02      9.98572E-03    2.76775E-02 600    49.85      1.25577E-04    7.53520E-02      9.99020E-03    2.76903E-02 700    42.75      1.07685E-04    7.53858E-02      9.99448E-03    2.77024E-02 800    37.41      9.42500E-05    7.54065E-02      9.99712E-03    2.77094E-02 900    33.26      8.37973E-05    7.54144E-02      9.99869E-03    2.77136E-02 1,000    29.94      7.54335E-05    7.54312E-02      1.00011E-02    2.77201E-02 1,100    27.22      6.85754E-05    7.54447E-02      1.00022E-02    2.77236E-02 1,200    24.96      6.28771E-05    7.54476E-02      1.00029E-02    2.77255E-02 6.3-7
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Table 6.3 Composition of Modeled Steels Component                SCALE Nuclide ID        Number Density (a/b-cm)
Type 304 Stainless Steel for HalfPACT Package Cr                          24304                    1.74726E-02 Mn                          25055                    1.74071E-03 Fe                          26304                    5.85446E-02 Ni                          28304                    7.74020E-03 P                          15031                    6.94680E-05 Si                          14000                    1.70252E-03 C                          6012                    3.18772E-04 Carbon Steel used in Case D Fe                          26000                    8.34982E-02 C                          6012                    3.92503E-03 Table 6.3 Composition of the Polyethylene/Water/Beryllium Reflector Component                SCALE Nuclide ID        Number Density (a/b-cm) 25% Polyethylene/ 74% Water/ 1% Beryllium Reflector used in Case A C                          6012                    9.91472E-03 H                          1001                    6.92387E-02 O                          8016                    2.47046E-02 Be                          4309                    1.23621E-03 99% Polyethylene/ 1% Beryllium used in Cases C and D C                          6012                    3.92623E-02 H                          1001                    7.85246E-02 Be                          4309                    1.23621E-03 70% Polyethylene/ 29% Water/ 1% Beryllium used in Case D C                          6012                    2.77612E-02 H                          1001                    7.48855E-02 O                          8016                    9.68153E-03 Be                          4309                    1.23621E-03 6.3-8
 
HalfPACT Safety Analysis Report                                                                      Rev. 9, August 2022 325 FGE moderated with 25% polyethylene/ 75% water, 340 FGE and 5 g Pu-240 moderated with 25% polyethylene/ 75% water, 360 FGE and 15 g Pu-240 moderated with 25% polyethylene/ 75% water, or 380 FGE and 25 g Pu-240 moderated with 25% polyethylene/ 75% water 25% polyethylene/ 74% water/ 1% beryllium mixture filling the ICV Figure 6.3 Case A Contents Model 6.3-9
 
HalfPACT Safety Analysis Report                                                            Rev. 9, August 2022 100 FGE moderated with 25% polyethylene/ 75% water Beryllium at theoretical density filling the ICV Figure 6.3 Case B Contents Model 6.3-10
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 250 FGE moderated with 100% polyethylene 99% polyethylene/ 1% beryllium mixture filling the ICV Figure 6.3 Case C Contents Model 6.3-11
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 125 FGE moderated with 70% polyethylene/ 30% water or 100% polyethylene 0.06 in. steel, 0.15 in. polyethylene, and                        200 FGE moderated with 0.06 in. steel layers separating cylinders                        70% polyethylene/ 30% water plus an additional 0.50 in. polyethylene                          or 100% polyethylene or water gap in the case of 100%
polyethylene moderation 70% polyethylene/ 29% water/ 1% beryllium or 99% polyethylene/ 1% beryllium mixture filling the ICV Figure 6.3 Case D Contents Model 6.3-12
 
HalfPACT Safety Analysis Report                                                                                                      Rev. 9, August 2022 21 [98.1869cm]
R3832 ICV REGION                  PACKAGING MODEL OCA REGION                                                  R38327 [97.0756cm]
CONTENTS MODEL (RADIUS VARIES)
ICV/OCV SHELLS 7/16 [1.1113cm] THK TYPE 304 STAINLESS STEEL (SIDE) 1 [179.0700cm]
702              70 [177.8000cm]                                                                                      4415                4515 16 [114.1413cm]    16 [116.6813cm]
R4615 16 [119.2213cm]                ICV/OCV SHELLS          OCA OUTER SHELL 1/2 [1.2700cm] THK      1/4 [0.6350cm] THK TYPE 304 STAINLESS STEEL TYPE 304 STAINLESS STEEL 3 [119.8563cm]
R4716                                                      (SIDE, TOP, AND BOTTOM)
(TOP AND BOTTOM)
Figure 6.3 NCT, Single-Unit Model; R-Z Slice 6.3-13
 
HalfPACT Safety Analysis Report                                                                                                        Rev. 9, August 2022 ICV REGION                PACKAGING 21 [98.1869cm]
R3832 MODEL OCA REGION                                                                                        ICV/OCV SHELLS CONTENTS MODEL                                                            7/16 [1.1113cm] THK (RADIUS VARIES)                    R38 7 [97.0756cm]                    TYPE 304 STAINLESS STEEL 32 (SIDE) 7 [143.3513cm]
5616              5515 16 [142.0813cm]                                                                                    4415 16 [114.1413cm]  4515 16 [116.6813cm]
21 [110.8869cm]
R4332                                                    OCA OUTER SHELL ICV/OCV SHELLS 1/2 [1.2700cm] THK      1/4 [0.6350cm] THK TYPE 304 STAINLESS STEEL TYPE 304 STAINLESS STEEL R4329                                                    (SIDE, TOP, AND BOTTOM) 32 [111.5219cm]              (TOP AND BOTTOM)
Figure 6.3 HAC, Single-Unit Model; R-Z Slice 6.3-14
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Figure 6.3 Array Model Variation 0 (Reflective Boundary Conditions Imposed) 6.3-15
 
HalfPACT Safety Analysis Report                        Rev. 9, August 2022 Figure 6.3 Array Model Variation 1; X-Y Slice Through Top Axial Layer 6.3-16
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 6.4 Criticality Calculations A description of the criticality calculations performed for the HalfPACT package is presented in this section. The calculational methodology is discussed in Section 6.4.1, Calculational or Experimental Method. The optimization of the payload model is discussed in Section 6.4.2, Fuel Loading or Other Contents Loading Optimization. The results of all calculations are presented in Section 6.4.3, Criticality Results.
The intent of the analysis is to demonstrate that the HalfPACT package is safely subcritical under normal conditions of transport (NCT) and hypothetical accident conditions (HAC).
6.4.1 Calculational or Experimental Method Calculations for the HalfPACT package are performed with the three-dimensional Monte Carlo transport theory code, KENO-V.a 1. The SCALE-PC v4.4a 2, CSAS25 utility 3 is used as a driver for the KENO code. In this role, CSAS25 determines nuclide number densities, performs resonance processing, and automatically prepares the necessary input for the KENO code based on a simplified input description. The 238 energy-group (238GROUPNDF5), cross-section library based on ENDF/B-V cross-section data 4 is used as the nuclear data library for the KENO-V.a code.
The KENO code has been used extensively in the criticality safety industry. KENO-V.a is an extension of earlier versions of the KENO code and includes many versatile geometry capabilities and screen plots to facilitate geometry verification. The KENO-V.a code and the associated 238GROUPNDF5 cross-section data set are validated for proper operation on the PC platform by performing criticality analyses of a number of relevant benchmark criticality experiments. A description of these benchmark calculations, along with justification for the computed bias in the code and library for the relevant region of applicability, is provided in Section 6.5, Critical Benchmark Experiments.
6.4.2 Fuel Loading or Other Contents Loading Optimization The allowable fuel loading for a single HalfPACT package is based on the FGE package fissile loading limit established in the CH-TRAMPAC 5. The analysis demonstrates that the HalfPACT package is safely subcritical under NCT and HAC. Calculations are based on the following conservative assumptions:
1 L. M. Petrie and N. F. Landers, KENO-V.a: An Improved Monte Carlo Criticality Program with Supergrouping, ORNL/NUREG/CSD-2/V2/R6, Volume 2, Section F11, March 2000.
2 Oak Ridge National Laboratory (ORNL), SCALE 4.4a: Modular Code System for Performing Standardized Computer Analyses for Licensing Evaluation for Workstations and Personal Computers, ORNL/NUREG/CSD-2/R6, March 2000.
3 N. F. Landers and L. M. Petrie, CSAS: Control Module For Enhanced Criticality Safety Analysis Sequences, ORNL/NUREG/CSD-2/V1/R6, Volume 1, Section C4, March 2000.
4 W. C. Jordan and S. M. Bowman, Scale Cross-Section Libraries, ORNL/NUREG/CSD-2/V3/R6, Volume 3, Section M4, March 2000.
5 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
6.4-1
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 1. Pu-239 is present at the fissile gram equivalent (FGE) limit. FGE limits with 0 g, 5 g, 15 g, and 25 g Pu-240 are calculated for Case A. FGE limits ignoring Pu-240 are calculated for Cases B, C and D.
: 2. All Pu is assumed to be optimally moderated and reflected with the optimal degree of moderation determined in each case for the applicable moderator. Studies indicate that the presence of voids in the optimal spherical contents model significantly reduces keff. The presence of less than or equal to 1% by weight beryllium in the moderator was also shown to have a small effect on keff, and at larger quantities, keff is reduced.
: 3. The reflector material is tight fitting around the fissile geometry and assumed to fill the inner containment vessel (ICV) at up to 100% of theoretical density. Especially in Case B with a beryllium reflector, results in Section 6.4.3, Criticality Results show that the presence of voids in the reflector reduces keff.
The two additional conservative assumptions below are applicable to Cases A, B and C but not to Case D. As discussed is Section 6.3.1.4, Case D Contents Model, Case D is applicable to a very specific scenario and thus details of the specific configuration are credited.
: 4. The fissile material is represented in a spherical geometry. Calculations performed for other geometries, such as cylinders and cubes, indicate a reduction in keff for these other geometries
: 5. All structural material comprising the payload drums and material within the payload drums, other than Pu-239 and hydrogenous material (represented as a polyethylene/water/beryllium mixture), are conservatively neglected.
The same conservative assumptions that are used to analyze the single-unit HalfPACT package are used for the infinite array calculations. However, the presence of reflector in the ICV and outer confinement assembly (OCA) region and water around the package tends to isolate the replicated fissile regions from each other. In order to identify the limiting case, the volume fraction of the materials in these regions are varied in order to maximize reactivity of the configuration. Additional conservative assumptions used to model the HalfPACT package are delineated in Section 6.2, Package Contents.
6.4.3 Criticality Results The results of the calculations for the HalfPACT package criticality evaluation are divided into two sections. Results for a single HalfPACT package are presented in Section 6.4.3.1, Criticality Results for a Single HalfPACT Package, and results for arrays of HalfPACT packages are presented in Section 6.4.3.2, Criticality Results for Infinite Arrays of HalfPACT Packages.
Reported multiplication factors represent the computed keff values plus twice the standard deviation in the result calculated for each case, as follows:
ks = keff + 2 This quantity is then compared with the upper subcriticality limit (USL) in order to demonstrate an adequate margin of subcriticality. Generally, the Monte Carlo calculations reported here are performed with sufficient histories to bring the computed relative standard deviation in the result to approximately 0.1%. Typical KENO parameters required to obtain this level of uncertainty are 1000 generations of 1000 histories per generation, with the initial 50 generations skipped.
6.4-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 6.4.3.1      Criticality Results for a Single HalfPACT Package With the model described in Section 6.3.3, Single-Unit Models, subcriticality of the HalfPACT package under both NCT and HAC is demonstrated for each case.
6.4.3.1.1      Case A Single Unit Results The results of studies that identify optimal model parameters for NCT calculations are summarized in Table 6.4-1 and Table 6.4-2. Although tabulated values of both ks and the reported Monte-Carlo standard deviation, , are provided, recall that ks includes the 2 uncertainty in the result.
Calculations were performed for the single-unit HalfPACT package model to demonstrate the reactivity effect of adding less than or equal to 1% by weight quantities of beryllium to the package under NCT and HAC. First, the reactivity of a 325 FGE sphere of 239Pu, polyethylene and water with a polyethylene/water mixture filling the ICV and OCA (25% by volume polyethylene and 75% by volume water in both the moderator and reflector) was calculated.
Optimal moderation of the contents model is determined by parametrically varying the H/Pu ratio in the fissile sphere. Then, two different compositions for the fissile moderator were considered, namely one in which the moderator consisted only of 239Pu, polyethylene and water and the other in which the moderator contained less than or equal to 1% by weight quantities of beryllium resulting in a conservative mixture of 239Pu and 25% polyethylene, 74% water and 1%
by volume beryllium. In both cases, the ICV and OCA regions were filled with a 25%
polyethylene, 74% water and 1% by volume beryllium. The results of these calculations are shown in Table 6.4-1. The difference in reactivity for the cases with beryllium in the moderator and those without is statistically insignificant. However, the maximum reactivity occurs when beryllium is not included in the moderator but is included in the reflector. Thus, a polyethylene/water moderator and polyethylene/water/beryllium reflector were modeled in the remainder of the calculations.
Table 6.4-2 shows that the reactivity of the NCT single-unit model decreases as the volume fraction of the reflector material is decreased. As expected for a single unit, the full density reflector case is limiting, with a ks value of 0.9339.
Thus, optimal reactivity parameters for the single-unit, NCT model with a 25% polyethylene and 75% water moderator are H/Pu(900) at maximum reflection conditions with a 25% polyethylene, 74% water, and 1% beryllium reflector composition.
For HAC conditions, variation of ks with H/Pu ratio at maximum reflection conditions is shown in Table 6.4-3. The maximum ks value (0.9331) for the single-unit, HAC occurs at H/Pu(1000).
Note that the maximum reactivity of the NCT single unit model (0.9339) is statistically the same as the maximum reactivity for the HAC single unit model. This is expected because of the similarity of the models and the fact that maximum reflection increases the reactivity of a single unit. Although the OCA region is thinner under HAC vs. NCT, the single-unit package model contains a 30 cm external water reflector to ensure that the package is infinitely reflected under both HAC and NCT.
6.4.3.1.2      Case B Single Unit Results Section 6.4.3.2.1, Case A Infinite Array Results, found that the maximum reactivity of a single-unit HalfPACT package under NCT or HAC conditions is statistically equivalent to that of an 6.4-3
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 infinite array of HAC packages under maximum reflection conditions. Thus the analysis given in Section 6.4.3.2.2, Case B Infinite Array Results is bounding for the Case B single unit.
6.4.3.1.3      Case C Single Unit Results Section 6.4.3.2.1, Case A Infinite Array Results, found that the maximum reactivity of a single-unit HalfPACT package under NCT or HAC conditions is statistically equivalent to that of an infinite array of HAC packages under maximum reflection conditions. Thus the analysis given in Section 6.4.3.2.3, Case C Infinite Array Results is bounding for the Case C single unit.
6.4.3.1.4      Case D Single Unit Results Section 6.4.3.2.1, Case A Infinite Array Results, found that the maximum reactivity of a single-unit HalfPACT package under NCT or HAC conditions is statistically equivalent to that of an infinite array of HAC packages under maximum reflection conditions. Thus the analysis given in Section 6.4.3.2.4, Case D Infinite Array Results is bounding for the Case D single unit.
6.4.3.1.5      Conclusions from Single Unit Calculations Based on optimum moderation of the fissile contents and the maximum reflection conditions modeled by filling the ICV and OCA regions with full density materials appropriate for each case and surrounding the package by an additional 30 cm of water, all single unit results are less than the USL. Thus, a single HalfPACT package will remain subcritical under both NCT and HAC conditions.
6.4.3.2      Criticality Results for Infinite Arrays of HalfPACT Packages The infinite array model studies the interaction between the fissile contents in adjacent HalfPACT packages. The models described in Section 6.3, Model Specification provide the basis for the KENO-V.a calculations. The only difference in the NCT and HAC models is that the thickness of the OCA area is reduced to 5 inches (12.7000 cm) in the HAC model. Thus, the interaction between HAC packages will be greater compared to NCT packages as the spacing between fissile regions is smaller. Also, the results shown below indicate that the reactivity effects of array interaction are less than those of close, full reflection of the package contents. Thus, the infinite array calculations based on the HAC model performed in the following subsections demonstrate that an infinite array of HalfPACT packages is safely subcritical under both NCT and HAC conditions.
In addition, the infinite array calculations assume the presence of interspersed water between the damaged packages. The volume fraction of water in the array interstitial space, abbreviated Int in the tables, is varied to determine the most reactive condition.
6.4.3.2.1      Case A Infinite Array Results As in the single unit calculations for Case A, additional moderation of the spheres of fissile contents is assumed by in-leakage of water into the ICV. The maximum polyethylene density in the cavity is 25% and 1% by volume beryllium is present. The fissile material is assumed to mix homogeneously with a 25% polyethylene/75% water moderator (by volume). The ICV and OCA areas are filled with a 25% polyethylene/74% water/1% beryllium composition (by volume) reflector. The moderator does not contain 1% by volume beryllium based on the slight reduction in ks obtained from the single-unit model when beryllium was added to the moderator as discussed in 6.4-4
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 Section 6.4.3.1.1, Case A Single Unit Results. The optimum H/Pu ratio for the HAC infinite array model is determined to be 1000 from the results in Table 6.4-4.
Results for an infinite number of HalfPACT packages arranged in a close-packed, square-pitched array with contents models centered in each package (model variation 0) and various reflector volume fractions are shown in Table 6.4-5. These results indicate that the reactivity effect of tight reflection of the fissile contents by the full density 25% polyethylene/74% water/1%
beryllium mixture is greater than that of array interaction. With the reflector removed and the ICV, OCA and exterior regions of the package voided, the array interaction effect is maximized.
However, in this case the computed reactivity is less than that at full moderator density in which the packages are effectively isolated from one another.
These results also indicate that the HAC infinite array maximum reactivity (0.9331) achieved with maximum reflection is statistically equivalent to the HAC single-unit maximum reactivity (0.9331) and the NCT single-unit maximum reactivity (0.9339). Thus, the HAC infinite array model with maximum reflection is equivalent to the single-unit model and is used in the remainder of the calculations.
The reactivity results for the fissile contents displacement Variation 1 described in Section 6.3.4, Array Models, are shown in Table 6.4-6 as a function of H/Pu for the case with only the ICV filled with the polyethylene/water/beryllium reflector mixture and the case with the entire interior and exterior of the package voided. The case with maximum array interaction resulted in a lower ks compared to the case with the ICV region filled with the polyethylene/water/beryllium mixture. Both model Variation 1 cases, however, were less reactive than the Variation 0 model with the spheres centered in the package surrounded by the full density reflector mixture.
The addition of Pu-240 to the fissile sphere was also studied and FGE limits calculated based on the Pu-240 gram content in the package. As shown in Table 6.4-7, a package containing 5 g Pu-240 is subcritical at a FGE limit of 340, a package containing 15 g Pu-240 is subcritical at a FGE limit of 360 and a package containing 25 g Pu-240 is subcritical at a FGE limit of 380. The fissile sphere was modeled centered in the package with the polyethylene/water/beryllium mixture filling the ICV and OCA regions and water in the interstitial region between packages as these parameters were found to result in the most reactive configuration for the cases without Pu-240. These limits are based on the grams of Pu-240 present, not wt% Pu-240 in order to allow the limits to apply to packages containing both U and Pu fissile isotopes. Calculations were performed based on the 340 FGE limit with 5 g Pu-240 with varying mixtures of U-235 and Pu-239 to verify applicability of this limit to mixed fissile systems. The conversion factor of 0.643 g U-235 per FGE given in the CH-TRAMPAC 6 was used. The results shown in Table 6.4-8 verify that mixed fissile systems will remain subcritical under this limit. In fact, the most reactive scenario occurs with 100% Pu-239. The case with 100% U-235 and 5 g Pu-240 is obviously unrealistic but shown for comparison purposes.
All infinite array results are less than the USL. Thus, an infinite array of HalfPACT packages containing 325 FGE per package (with 0 g Pu-240), 340 FGE per package (with 5 g Pu-240),
360 FGE per package (with 15 g Pu-240), and 380 FGE per package (with 25 g Pu-240) under the limitations imposed for Case A is subcritical.
6 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
6.4-5
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 6.4.3.2.2      Case B Infinite Array Results The results for the Case B beryllium reflected cases are consistent with the results for Case A in that the maximum reactivity occurs at maximum reflection conditions. The maximum reactivity (0.9184) occurs at an H/Pu ratio of 800 for the 100 FGE beryllium reflected, polyethylene/water moderated scenario as shown in Table 6.4-9. The addition of beryllium to the fissile sphere was also studied as beryllium was found to increase reactivity when added to a polyethylene/water moderator in a water reflected system per SAIC-1322-001 7. Volume fractions in the fissile sphere from 1 to 60% beryllium were modeled and the results shown in Table 6.4-10 indicate that ks is reduced as more beryllium is added to this beryllium reflected system. The results in Table 6.4-11 indicate that the reactivity is reduced as the volume fraction of the reflectors in the ICV, OCA and interstitial regions are reduced. As expected from the Case A results, array Variation 1 with the fissile spheres moved off-center in the ICV to minimize distance between spheres in adjacent packages is significantly less reactive than the Variation 0 base model. These results are shown in Table 6.4-12. Overall, these calculations indicate that an infinite array of HalfPACT packages is subcritical with 100 FGE and an unlimited mass of special reflectors.
6.4.3.2.3      Case C Infinite Array Results The Case C results support the 250 FGE package limit for mechanically compacted waste that does not meet the Case D specifications. As shown in Table 6.4-13, the reactivity is increased when 1% beryllium is added to the polyethyelene reflector in the ICV and the maximum reactivity (0.9345) occurs at an H/Pu ratio of 900. The results in Table 6.4-14 indicate that the reactivity is lower as the volume fraction of the reflector materials in the ICV, OCA and interstitial regions are reduced. Again, moving the fissile spheres off-center in the ICV reduces reactivity based on the results tabulated in Table 6.4-15. Thus, again the maximum reactivity occurs at maximum reflection conditions with the fissile spheres centered in the packages and remains below the USL. Thus, an infinite array of HalfPACT packages containing machine compacted waste is subcritical at 250 FGE per package.
6.4.3.2.4      Case D Infinite Array Results The results of the Case D calculations show that at a maximum packing fraction of 70%,
machine compacted pucks are subcritical when each overpack drum is limited to 200 FGE and the package is limited to 325 FGE or if the packing fraction is not limited, when a minimum gap of 0.50 inches exists between the puck drums. The results shown in Table 6.4-16 indicate that the highest reactivity for the modeled configuration at 70% packing fraction (0.9325) occurs at an H/Pu ratio of 800 and the highest reactivity at 100% packing fraction (0.9349) also occurs at an H/Pu ratio of 800. At 100% packing fraction, the required separation distance between the puck drums, in addition to the 1/2 thickness of the the drum steel and the 1/2 thickness of the slip sheet/ reinforcing plate thicknesses modeled, is 0.50 inches. The reactivity resulting from filling the gap with polyethylene versus water is statistically equivalent. As in the other cases, the results in Table 6.4-17 show that reducing the volume fraction of reflector material in the ICV, OCA and interstitial regions reduces reactivity as does placing the fissile material off-center in 7
Neeley, G. W., D. L. Newell, S. L. Larson, and R. J. Green, Reactivity Effects of Moderator and Reflector Materials on a Finite Plutonium System, SAIC-1322-001, Revision 1, Science Applications International Corporation, Oak Ridge, Tennessee, May 2004.
6.4-6
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 the package (i.e., infinite array variation 1) as shown in Table 6.4-18. The cases in these tables were only calculated at the 70% packing fraction, but the results are obviously also applicable to the 100% packing fraction case. Thus, an infinite array of HalfPACT packages containing machine compacted waste under the specific restrictions applied to Case D is subcritical at 325 FGE per package.
6.4.3.2.5      Conclusions from Infinite Array Calculations The calculations reported in this section are performed with conservative representations of arrays of damaged HalfPACT packages. The HAC model used gives a smaller center-to-center spacing between packages compared to the NCT model. In addition, the results indicate that the reactivity effects of array interaction are less than those of close, full reflection of the package contents. Hence, maximum reactivity results for arrays of HalfPACT packages under NCT are essentially the same as those under HAC at optimal moderation conditions. Therefore, infinite arrays of HalfPACT packages are safely subcritical under both NCT and HAC, and the requirements of 10 CFR &sect;71.59 8 are satisfied. Furthermore, a CSI of zero (0.0) is justified.
6.4.3.3      Special Reflectors in CH-TRU Waste As described previously, the only special reflectors credibly applicable to CH-TRU waste criticality analysis are: beryllium (Be), beryllium oxide (BeO), carbon (C), deuterium (D2O),
magnesium oxide (MgO), and depleted uranium (0.3% 235U) when present in quantities greater than 1 weight percent. Each special reflector with regard to its possible presence in CH-TRU waste is discussed below:
Beryllium and Beryllium Oxide - Be, and/or BeO, may be present in CH-TRU waste in quantities greater than 1% by weight. The limits for payload containers other than pipe overpacks are found in Table 6.1-1 and Table 6.1-2 under Case B. As described in Section 6.2.1, beryllium is the limiting special reflector for CH-TRU waste. For pipe overpack configurations, beryllium may be present in neutron sources and other source materials where the beryllium is completely bound to the fissile material in the source. Therefore, for pipe overpack configurations, Case E limits in Table 6.1-1 and Table 6.1-2 apply.
Carbon - Carbon is present as a constituent in CH-TRU waste but not in forms that can credibly reconfigure as a reflector. For example: (1) Carbon may be present as graphite molds or crucibles. In these forms the carbon will be chemically and irreversibly bound to the plutonium or other fissile material and cannot be separated. (2) Carbon may be present in filter media as spent or activated carbon. The plutonium or other fissile material would then be attached to the carbon filter media and would not be easily separated. (3) Granular activated carbon (GAC) pads may also be present in an enclosed bag for the purpose of absorbing volatile organic compounds. Once the GAC pad is placed inside the payload container, there is no credible method for the carbon to fully-surround the fissile material and reconfigure as a reflector.
(4) Carbon may also be present in alloys, which are by definition chemically and/or mechanically bound. In summary, there is no identified mechanism that could cause the carbon in CH-TRU waste to be separated from the fissile material and/or to be reconfigured as a reflector.
8 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
6.4-7
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Deuterium - The presence of liquid waste in the payload containers, except for residual amounts in well-drained containers, is prohibited. As specified by the CH-TRAMPAC, the total volume of residual liquid in a payload container shall be less than 1 percent (volume) of the payload container. This limitation on the authorized contents is such that D2O will not be present in greater than 1% by weight.
Magnesium Oxide - Magnesium oxide crucibles used in high temperature-controlled applications, such as reduction processes, may be present in solid inorganic waste forms such as glass, metal, and pyrochemical salts. If present, MgO will be bound to the fissile material and would not be easily separated. MgO used for neutralization in solidified material cannot be separated out as it is chemically reacted in the waste generation process. There is no identified mechanism that could cause the magnesium oxide in CH-TRU waste to be reconfigured as a reflector.
Depleted Uranium (0.3% 235U) - Depleted uranium may be present in CH-TRU waste, but it will be chemically and/or mechanically bound to the plutonium or physically inseparable because the densities of U and Pu are similar. Separation by mechanical means or by leaching is extremely difficult and is considered highly unlikely in CH-TRU waste. Depleted uranium in CH-TRU waste will, therefore, not be separated from the fissile material and/or reconfigured as a reflector.
6.4.3.4    Machine Compacted CH-TRU Waste Five criticality cases were analyzed for machine compacted CH-TRU waste:
Case C assumes all the machine compacted waste reconfigures into a single sphere during the hypothetical accident conditions and is applicable to machine compacted waste in a 55-gallon drum, 85-gallon drum, 100-gallon drum, or SWB. As shown in Table 6.1-1 and Table 6.1-2, the limits for Case C are 250 FGE per drum, 250 FGE per SWB, and 250 FGE per package.
Case D assumes either a maximum 70% packing fraction or a minimum vertical spacing of at least 0.50 inches is maintained between two cylinders during the hypothetical accident conditions (in addition to credit for the steel and slipsheets as described in Section 6.3.1.4).
Case D is applicable to machine compacted waste in the form of compacted pucks in a 55-gallon drum, 85-gallon drum, or 100-gallon drum. As shown in Table 6.1-1 and Table 6.1-2, the limits for Case D are 200 FGE per payload container and 325 FGE per package.
Case E assumes that the fissile material in each pipe overpack is moderated with 100%
polyethylene and the remainder of the pipe is filled with up to 100% dense polyethylene. Case E is thus applicable to machine compacted waste in a standard, S100, S200, or S300 pipe overpack.
As shown in Table 6.1-1 and Table 6.1-2, the limits for Case E are 200 FGE per payload container and 1,400 FGE per package.
Case H assumes all the machine compacted waste reconfigures into a single sphere during the hypothetical accident conditions and is applicable to machine compacted waste in a shielded container (i.e., SC-30G1, SC-30G2, SC-30G3, SC-55G1, and SC-55G2). As shown in Table 6.1-1 and Table 6.1-2, the limits for Case H are 245 FGE per shielded container and 245 FGE per package.
6.4-8
 
HalfPACT Safety Analysis Report                                                          Rev. 9, August 2022 Case I assumes that the fissile material in each CCO is moderated and reflected by a mixture of 25% polyethylene, 74% water, and 1% beryllium by volume. An evaluation 9 was performed determining that this case is also applicable to machine compacted waste when limiting the amount of polyethylene in a CCO to a maximum of 2,000 grams. As shown in Table 6.1-1 and Table 6.1-2, the limits for Case I with controls on the plastic content are 380 FGE per payload container and 2,660 FGE per package.
6.4.3.5    Applicable Criticality Limits for CH-TRU Waste In conclusion, the only special reflector in CH-TRU waste requiring special controls is Be/BeO.
The criticality analyses for CH-TRU waste with greater than 1% by weight Be/BeO in any form is bounded by Case B (excluding shielded containers, and CCOs). Non-machine compacted CH-TRU waste payloads are covered by Cases A, E, G, and I. Machine compacted CH-TRU waste payloads are covered by Cases C, D, E, H, and I. The applicable FGE limits are specified by case in Table 6.1-1 and Table 6.1-2. Considering machine compaction and special reflectors in CH-TRU waste, as discussed in Sections 6.4.3.3 and 6.4.3.4, the applicable FGE limits are summarized below.
9 K. L. Moyant, Evaluation of the Criticality Safety Analysis for Criticality Control Overpacks Containing Machine Compacted Waste, CCO-CAL-0005, Rev. 0, Nuclear Waste Partnership LLC, Carlsbad, NM, July 2020.
6.4-9
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 FGE Limits Considering Machine Compaction and Special Reflectors Fissile Limit per Payload      Fissile Limit per Applicable Payload            Container            Package          Analysis Contents            Container          (Pu-239 FGE)        (Pu-239 FGE)          Case Drum                        325                325                A Not machine Pipe Overpack                200                1,400                E compacted with SWB                          325                325                A 1% by weight Shielded Container          325                325                G Be/BeO CCO                          380                2,660                I Drum                        100                100                B Not machine Pipe Overpack                200                1,400              E compacted with SWB                          100                100                B
> 1% by weight Shielded Container      Unauthorized        Unauthorized          N/A Be/BeO CCO                    Unauthorized        Unauthorized          N/A Drum                        250                250                C Machine Pipe Overpack                200                1,400                E compacted with SWB                          250                250                C 1% by weight Shielded Container          245                245                H Be/BeO CCO                    Unauthorized        Unauthorized          N/A Machine        Drum                        200                325                D compacted with      Pipe Overpack          Unauthorized        Unauthorized          N/A controls and  1%    SWB                    Unauthorized        Unauthorized          N/A by weight        Shielded Container      Unauthorized        Unauthorized          N/A Be/BeO        CCO                        380                2,660                I Drum                    Unauthorized        Unauthorized          N/A Machine Pipe Overpack          Unauthorized        Unauthorized          N/A compacted with SWB                    Unauthorized        Unauthorized          N/A
> 1% by weight Shielded Container      Unauthorized        Unauthorized          N/A Be/BeO CCO                    Unauthorized        Unauthorized          N/A Notes:
Special reflectors other than Be/BeO in greater than 1% by weight quantities are exempted by the evaluation given in Section 6.4.3.3.
Case E is applicable in lieu of Case F because Be/BeO is always mechanically or chemically bound to fissile material in pipe overpack payloads (see Section 6.4.3.3).
The contents shall be machine compacted waste in the form of puck drums with the payload controls specified in Sections 6.2.4 and 6.3.1.4.
Limited to a maximum of 2,000 grams of plastic per CCO.
6.4-10
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 6.4 Single-Unit, NCT, Case A, 325 FGE; ks vs. H/Pu Ratio with Different Moderator and Reflector Compositions Case          H/Pu      Composition          keff            ks NPWPW5          500                          0.8981  0.0011    0.9003 NPWPW6          600                          0.9141  0.0010    0.9161 NPWPW7          700                          0.9242  0.0010    0.9262 NPWPW8          800        Moderator and      0.9280  0.0010    0.9300 Reflector in ICV and NPWPW9          900                          0.9299  0.0010    0.9319 OCA = 25% poly/
NPWPW10        1,000          75% water      0.9288  0.0009    0.9306 NPWPW11        1,100                          0.9247  0.0010    0.9267 NPWPW12        1,200                          0.9216  0.0010    0.9236 NPWPW13        1,300                          0.9155  0.0009    0.9173 NPWPWB5          500                          0.9000  0.0009    0.9018 NPWPWB6          600                          0.9149  0.0011    0.9171 NPWPWB7          700          Moderator =      0.9259  0.0010    0.9279 NPWPWB8          800      25% poly/75% water  0.9297  0.0009    0.9315 NPWPWB9          900      Reflector in ICV and 0.9319  0.0010    0.9339 OCA = 25% poly/
NPWPWB10        1,000        74% water/      0.9308  0.0009    0.9326 NPWPWB11        1,100        1% beryllium      0.9281  0.0009    0.9299 NPWPWB12        1,200                          0.9211  0.0009    0.9229 NPWPWB13        1,300                          0.9169  0.0009    0.9187 N2PWB5          500                          0.9015  0.0011    0.9037 N2PWB6          600                          0.9155  0.0010    0.9175 N2PWB7          700                          0.9265  0.0010    0.9285 Moderator and N2PWB8          800      Reflector in ICV and 0.9302  0.0010    0.9322 N2PWB9          900      OCA = 25% poly/    0.9318  0.0010    0.9338 N2PWB10        1,000        74% water/      0.9302  0.0010    0.9322 1% beryllium N2PWB11        1,100                          0.9277  0.0008    0.9293 N2PWB12        1,200                          0.9224  0.0009    0.9242 N2PWB13        1,300                          0.9173  0.0010    0.9193 6.4-11
 
HalfPACT Safety Analysis Report                          Rev. 9, August 2022 Table 6.4 Single Unit, NCT, Case A, 325 FGE; Variation of Reflector Volume Fraction (VF) at Near-Optimal H/Pu Ratio Case      H/Pu    Reflector      VF        keff                ks NPWPWB9                              1.00    0.9319 0.0010        0.9339 NWCVOL95              ICV = OCA      0.95    0.9283 0.0010        0.9303 NWCVOL90              = 25% poly/      0.90    0.9256 0.0009        0.9274 NWCVOL75                74% water/    0.75    0.9157 0.0010        0.9177 900  1% Be at VF NWCVOL50                  given        0.50    0.8888 0.0009        0.8906 NWCVOL25              Int = water at  0.25    0.8434 0.0010        0.8454 NWCVOL10                VF given      0.10    0.7963 0.0011        0.7985 NWCVOL00                                0      0.7583 0.0010        0.7603 Table 6.4 Single-Unit, HAC, Case A, 325 FGE; ks vs. H/Pu at Maximum Reflection Conditions Case            H/Pu        Reflector      keff                ks HPWPWB5            500                      0.8996 0.0010        0.9016 HPWPWB6            600                      0.9149 0.0011        0.9171 ICV = OCA HPWPWB7            700                      0.9234 0.0009        0.9252
                                = 25% poly/
HPWPWB8            800        74% water/  0.9296 0.0010        0.9316 HPWPWB9            900          1% Be at    0.9295 0.0009        0.9313 HPWPWB10          1,000          VF=1.0    0.9311 0.0010        0.9331 Int = water at HPWPWB11          1,100                    0.9273 0.0009        0.9291 VF=1.0 HPWPWB12          1,200                    0.9219 0.0009        0.9237 HPWPWB13          1,300                    0.9170 0.0009        0.9188 6.4-12
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case A, 325 FGE; ks vs. H/Pu at Extremes of Reflection Conditions Case          H/Pu        Reflector      keff                  ks HINFAR5          500                    0.8997  0.0012        0.9021 HINFAR6          600                    0.9163  0.0010        0.9183 ICV = OCA HINFAR7          700                    0.9275  0.0009        0.9293
                                = 25% poly/
HINFAR8          800      74% water/    0.9291  0.0010        0.9311 HINFAR9          900        1% Be at    0.9307  0.0009        0.9325 HINFAR10        1,000        VF=1.0    0.9311  0.0010        0.9331 Int = water at HINFAR11        1,100                    0.9266  0.0010        0.9286 VF=1.0 HINFAR12        1,200                    0.9224  0.0008        0.9240 HINFAR13        1,300                    0.9161  0.0008        0.9177 HVINAR8          800                    0.8677  0.0010        0.8697 HVINAR9          900                    0.8759  0.0009        0.8777 HVINAR10          1,000                    0.8832  0.0010        0.8852 ICV = Void HVINAR11          1,100                    0.8859  0.0008        0.8875 OCA = Void HVINAR12          1,200                    0.8878  0.0009        0.8896 Int = Void HVINAR13          1,300                    0.8860  0.0008        0.8876 HVINAR14          1,400                    0.8840  0.0009        0.8858 HVINAR15          1,500                    0.8814  0.0008        0.8830 6.4-13
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case A, 325 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratios Case          H/Pu    Reflector        VF    keff              ks HINFAR10                                  1.00 0.9311  0.0010    0.9331 HWC10VOL95                                    0.95 0.9266  0.0009    0.9284 HWC10VOL90                ICV = OCA          0.90 0.9244  0.0011    0.9266 HWC10VOL75                = 25% poly/        0.75 0.9159  0.0010    0.9179 HWC10VOL50                  74% water/        0.50 0.8915  0.0010    0.8935 1000    1% Be at VF HWC10VOL25                    given          0.25 0.8483  0.0010    0.8503 HWC10VOL10                Int = water at    0.10 0.8047  0.0009    0.8065 HWC10VOL1                  VF given        0.01 0.7888  0.0009    0.7906 HWC10VOL01                                  0.001 0.8439  0.0009    0.8457 HVINAR10                                      0  0.8832  0.0010    0.8852 HINFAR12                                  1.00 0.9224  0.0008    0.9240 HWC12VOL90                                    0.95 0.9190  0.0009    0.9208 HWC12VOL95                ICV = OCA          0.90 0.9201  0.0009    0.9219 HWC12VOL75                = 25% poly/        0.75 0.9098  0.0009    0.9116 HWC12VOL50                  74% water/        0.50 0.8888  0.0010    0.8908 1,200  1% Be at VF HWC12VOL25                    given          0.25 0.8543  0.0010    0.8563 HWC12VOL10                Int = water at    0.10 0.8129  0.0009    0.8147 HWC12VOL1                  VF given        0.01 0.7972  0.0010    0.7992 HWC12VOL01                                  0.001 0.8014  0.0010    0.8034 HVINAR12                                      0  0.8878  0.0009    0.8896 6.4-14
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 Table 6.4 Infinite Array Variation 1, HAC, Case A, 325 FGE; Variation of H/Pu Ratio at Extremes of Reflection Conditions Case        Variation  H/Pu        Reflector    keff              ks HINFAROFF9                  900          ICV =  0.9226    0.0009  0.9244 HINFAROFF10                  1,000    25% poly/74% 0.9239    0.0010  0.9259 water/1% Be HINFAROFF11          1      1,100                  0.9209    0.0010  0.9229 at VF=1.0 HINFAROFF12                  1,200      OCA = Int = 0.9188    0.0010  0.9208 HINFAROFF13                  1,300          Void  0.9118    0.0008  0.9134 HVINAROFF9                    900                  0.8948    0.0010  0.8968 HVINAROFF10                  1,000      ICV = Void  0.9006    0.0009  0.9024 HVINAROFF11            1      1,100      OCA = Void  0.9027    0.0010  0.9047 HVINAROFF12                  1,200      Int = Void 0.9022    0.0009  0.9040 HVINAROFF13                  1,300                  0.8997    0.0009  0.9015 6.4-15
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case A; Variation of H/Pu Ratio for Various Gram Quantities of Pu-240 at Maximum Reflection Conditions Pu-240 Pu-239 Case                        H/239Pu Reflector    keff              ks (g)      (g) 5PU340H6                        600              0.9144    0.0011  0.9166 5PU340H7                        700      ICV =    0.9237    0.0022  0.9281 OCA =
5PU340H8                        800  25% poly/  0.9313    0.0009  0.9331 5PU340H9                        900  74% water/  0.9316    0.0010  0.9336 5      340 5PU340H10                        1,000  1% Be at  0.9304    0.0009  0.9322 VF=1.0 5PU340H11                        1,100              0.9278    0.0009  0.9296 Int = water 5PU340H12                        1,200  at VF=1.0  0.9248    0.0011  0.9270 5PU340H13                        1,300              0.9196    0.0010  0.9216 15PU360H6                        600              0.9136    0.0009  0.9154 15PU360H7                        700      ICV =    0.9233    0.0008  0.9249 OCA =
15PU360H8                        800  25% poly/  0.9307    0.0009  0.9325 15PU360H9                        900  74% water/  0.9337    0.0011  0.9359 15      360 15PU360H10                        1,000  1% Be at  0.9302    0.0009  0.9320 VF=1.0 15PU360H11                        1,100              0.9308    0.0008  0.9324 Int = water 15PU360H12                        1,200  at VF=1.0  0.9254    0.0010  0.9274 15PU360H13                        1,300              0.9197    0.0008  0.9213 25PU380H6                        600              0.9121    0.0009  0.9139 25PU380H7                        700      ICV =    0.9246    0.0010  0.9266 OCA =
25PU380H8                        800  25% poly/  0.9299    0.0009  0.9317 25PU380H9                        900  74% water/  0.9316    0.0010  0.9336 25      380            1% Be at 25PU380H10                        1,000              0.9339    0.0009  0.9357 VF=1.0 25PU380H11                        1,100              0.9298    0.0010  0.9318 Int = water 25PU380H12                        1,200  at VF=1.0  0.9268    0.0009  0.9286 25PU380H13                        1.300              0.9206    0.0008  0.9222 6.4-16
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case A, 5 g Pu-240, 340 FGE; ks vs. H/Pu for Various Combinations of U-235 and Pu-239 under Maximum Reflection Conditions Case            Fissile Material        H/X    keff              ks U100H3                                    300  0.9000  0.0011    0.9022 U100H4                                    400  0.9198  0.0009    0.9216 FGE = 100% U-235 U100H5                                    500  0.9261  0.0009    0.9279
                      = 528.7 g U-235 U100H6                                    600  0.9214  0.0009    0.9232 U100H7                                    700  0.9131  0.0010    0.9151 U75H4                                    400  0.9141  0.0010    0.9161 U75H5          FGE = 75% U-235/          500  0.9245  0.0009    0.9263 25% Pu-239 U75H6                                    600  0.9272  0.0010    0.9292
                      = 396.6 g U-235/
U75H7              85.0 g Pu-239          700  0.9224  0.0010    0.9244 U75H8                                    800  0.9162  0.0008    0.9178 U50H5                                    500  0.9188  0.0009    0.9206 U50H6          FGE = 50% U-235/          600  0.9272  0.0009    0.9290 50% Pu-239 U50H7                                    700  0.9275  0.0010    0.9295
                      = 264.4 g U-235/
U50H8            170.0 g Pu-239          800  0.9240  0.0008    0.9256 U50H9                                    900  0.9194  0.0010    0.9214 U25H5                                    500  0.9152  0.0010    0.9172 U25H6          FGE = 25% U-235/          600  0.9253  0.0011    0.9275 75% Pu-239 U25H7                                    700  0.9310  0.0010    0.9330
                      = 132.2 g U-235/
U25H8              255 g Pu-239          800  0.9295  0.0010    0.9315 U25H9                                    900  0.9289  0.0010    0.9309 5PU340H7                                    700  0.9237  0.0022    0.9281 5PU340H8                                    800  0.9313  0.0009    0.9331 FGE = 100% Pu-239 5PU340H9                                    900  0.9316  0.0010    0.9336
                        = 340 g Pu-239 5PU340H10                                  1,000 0.9304  0.0009    0.9322 5PU340H11                                  1,100 0.9278  0.0009    0.9296 Note:
1 g U-235 = 0.643 FGE 6.4-17
 
HalfPACT Safety Analysis Report                          Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case B, 100 FGE; ks vs. H/Pu at Maximum Reflection Conditions Case            H/Pu    Reflector    keff                  ks HINFAR5B            500    ICV = Be at  0.8892    0.0009      0.8910 HINFAR6B            600      VF=1.0    0.9041    0.0009      0.9059 HINFAR7B            700      OCA =    0.9127    0.0008      0.9143 HINFAR8B            800    25% poly/  0.9168    0.0008      0.9184 74% water/
HINFAR9B            900      1% Be at  0.9127    0.0009      0.9145 HINFAR10B          1,000      VF =1.0  0.9095    0.0008      0.9111 HINFAR11B          1,100    Int = water 0.9042    0.0008      0.9058 HINFAR12B          1,200    at VF=1.0  0.8988    0.0008      0.9004 6.4-18
 
HalfPACT Safety Analysis Report                          Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case B, 100 FGE; ks vs.
H/Pu for Various Moderator Volume Fractions of Beryllium under Maximum Reflection Conditions VF Beryllium Case                      H/Pu          keff                  ks in Moderator B01H6                        600        0.9027    0.0008      0.9043 B01H7                        700        0.9102    0.0009      0.9120 B01H8            1          800        0.9144    0.0010      0.9164 B01H9                        900        0.9129    0.0009      0.9147 B01H10                      1,000      0.9101    0.0008      0.9117 B10H6                        600        0.9027    0.0009      0.9045 B10H7                        700        0.9102    0.0009      0.9120 B10H8            10          800        0.9125    0.0008      0.9141 B10H9                        900        0.9104    0.0009      0.9122 B10H10                      1,000      0.9075    0.0009      0.9093 B20H6                        600        0.9001    0.0010      0.9021 B20H7                        700        0.9081    0.0009      0.9099 B20H8            20          800        0.9093    0.0009      0.9111 B20H9                        900        0.9094    0.0009      0.9112 B20H10                      1,000      0.9042    0.0008      0.9058 B40H6                        600        0.8972    0.0010      0.8992 B40H7                        700        0.9012    0.0009      0.9030 B40H8            40          800        0.9022    0.0009      0.9040 B40H9                        900        0.9010    0.0009      0.9028 B40H10                      1,000      0.8960    0.0008      0.8976 B60H6                        600        0.8822    0.0009      0.8840 B60H7                        700        0.8859    0.0008      0.8875 B60H8            60          800        0.8846    0.0009      0.8864 B60H9                        900        0.8815    0.0008      0.8831 B60H10                      1,000      0.8771    0.0008      0.8787 6.4-19
 
HalfPACT Safety Analysis Report                                      Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case B, 100 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratio Case        H/Pu    Reflector      VF          keff                    ks HINFAR8B                ICV = Be at    1.00      0.9168        0.0008      0.9184 HINFAR8B95                VF given      0.95      0.8973        0.0009      0.8991 HINFAR8B90                  OCA =        0.90      0.8838        0.0009      0.8856 HINFAR8B75                25% poly/      0.75      0.8320        0.0008      0.8336 800    74% water/
HINFAR8B50                1% Be at      0.50      0.7188        0.0009      0.7206 HINFAR8B25                VF given      0.25      0.5671        0.0008      0.5687 HINFAR8B10                Int = water    0.10      0.4678        0.0009      0.4696 HINFAR8B00              at VF given      0        0.5013        0.0008      0.5029 Table 6.4 Infinite Array Variation 1, HAC, Case B, 100 FGE; Variation of H/Pu Ratio at Reflector Volume Fraction to Maximize Interaction while Maintaining Beryllium Reflection Case        Variation      H/Pu        Reflector      keff                ks HINFAR8BOFF                      800                      0.7680      0.0010  0.7700 HINFAR9BOFF                      900        ICV = Be at    0.7752      0.0009  0.7770 HINFAR10BOFF                    1,000        VF=1.0      0.7795      0.0009  0.7813 1
HINFAR11BOFF                    1,100      OCA = Void      0.7798      0.0009  0.7816 HINFAR12BOFF                    1,200        Int = Void    0.7800      0.0008  0.7816 HINFAR13BOFF                    1,300                      0.7782      0.0007  0.7796 6.4-20
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case C, 250 FGE; ks vs. H/Pu at Maximum Reflection Conditions Case            H/Pu        Reflector      keff                ks C0B250H6            600          ICV =    0.9152  0.0010      0.9172 C0B250H7            700        100% poly    0.9248  0.0010      0.9268 C0B250H8            800          OCA =      0.9287  0.0010      0.9307 C0B250H9            900        25% poly/  0.9320  0.0010      0.9340 74% water/
C0B250H10          1,000        1% Be      0.9305  0.0009      0.9323 C0B250H11          1,100      Int = water  0.9274  0.0009      0.9292 C0B250H12          1,200          All at    0.9223  0.0010      0.9243 C0B250H13          1,300        VF=1.0    0.9148  0.0008      0.9164 C1B250H5            500                    0.8969  0.0010      0.8989 ICV =
C1B250H6            600        99% poly/  0.9148  0.0009      0.9166 C1B250H7            700          1% Be      0.9250  0.0009      0.9268 C1B250H8            800          OCA =      0.9309  0.0011      0.9331 25% poly/
C1B250H9            900        74% water/  0.9325  0.0010      0.9345 C1B250H10          1,000        1% Be      0.9296  0.0010      0.9316 C1B250H11          1,100      Int = water  0.9271  0.0009      0.9289 C1B250H12          1,200          All at    0.9237  0.0008      0.9253 C1B250H13          1,300        VF=1.0    0.9188  0.0009      0.9206 Table 6.4 Infinite Array Variation 0, HAC, Case C, 250 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratio Case        H/Pu    Reflector        VF    keff              ks C1B250H9                ICV = 99%      1.00  0.9325 0.0010      0.9345 C1B250H9V95              poly/1% Be      0.95  0.9295 0.0009      0.9313 at VF given C1B250H9V90                              0.90  0.9269 0.0010      0.9289 OCA = 25%
C1B250H9V75                poly/ 74%      0.75  0.9149 0.0010      0.9169 900 C1B250H9V50                water/ 1%      0.50  0.8880 0.0009      0.8898 Be at VF C1B250H9V25                  given        0.25  0.8460 0.0010      0.8480 C1B250H9V10              Int = water at  0.10  0.7974 0.0010      0.7994 C1B250H9V00                VF given        0  0.8560 0.0009      0.8578 6.4-21
 
HalfPACT Safety Analysis Report                                Rev. 9, August 2022 Table 6.4 Infinite Array Variation 1, HAC, Case C, 250 FGE; Variation of H/Pu Ratio at Reflector Volume Fraction to Maximize Interaction while Maintaining Reflection Case        Variation  H/Pu        Reflector    keff              ks C1BOFF7                    700                    0.9134    0.0010  0.9154 ICV = 99%
C1BOFF8                    800      poly/1% Be at 0.9202    0.0009  0.9220 C1BOFF9            1      900          VF=1.0    0.9218    0.0011  0.9240 C1BOFF10                  1,000      OCA = Int =  0.9224    0.0009  0.9242 Void C1BOFF11                  1,100                  0.9185    0.0009  0.9203 6.4-22
 
HalfPACT Safety Analysis Report                                  Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case D, 325 FGE; ks vs. H/Pu at Maximum Reflection Conditions Case            H/Pu    Reflector        keff                    ks 70% Polyethylene/ 30% Water Moderator and No Separation Between Pucks CASED70H5            500      ICV =        0.9123      0.0010      0.9143 CASED70H6            600    70% poly/      0.9245      0.0010      0.9265 29% water/
CASED70H7            700      1% Be        0.9298      0.0010      0.9318 CASED70H8            800      OCA =        0.9307      0.0009      0.9325 CASED70H9            900    25% poly/      0.9292      0.0010      0.9312 CASED70H10            1,000    74% water/      0.9257      0.0010      0.9277 1% Be CASED70H11            1,100                    0.9183      0.0008      0.9199 Int = water CASED70H12            1,200    All VF=1.0      0.9144      0.0009      0.9162 100% Polyethylene Moderator and 0.50 in. Separation Between Pucks Filled with Water CASED100H5            500      ICV =        0.9154      0.0010      0.9174 CASED100H6            600    99% poly/      0.9258      0.0009      0.9276 CASED100H7            700      1% Be        0.9319      0.0009      0.9337 CASED100H8            800      OCA =        0.9320      0.0008      0.9336 25% poly/
CASED100H9            900    74% water/      0.9310      0.0009      0.9328 CASED100H10          1,000      1% Be        0.9263      0.0009      0.9281 CASED100H11          1,100    Int = water    0.9233      0.0010      0.9253 CASED100H12          1,200    All VF=1.0      0.9147      0.0009      0.9165 100% Polyethylene Moderator and 0.50 in. Separation Between Pucks Filled with Polyethylene CASED100H5P            500      ICV =        0.9159      0.0010      0.9179 CASED100H6P            600    99% poly/      0.9261      0.0009      0.9279 CASED100H7P            700      1% Be        0.9319      0.0010      0.9339 CASED100H8P            800      OCA =        0.9329      0.0010      0.9349 25% poly/
CASED100H9P            900    74% water/      0.9308      0.0009      0.9326 CASED100H10P          1,000      1% Be        0.9260      0.0009      0.9278 CASED100H11P          1,100    Int = water    0.9210      0.0009      0.9228 CASED100H12P          1,200    All VF=1.0      0.9136      0.0009      0.9154 6.4-23
 
HalfPACT Safety Analysis Report                                    Rev. 9, August 2022 Table 6.4 Infinite Array Variation 0, HAC, Case D, 325 FGE; Variation of Reflector Volume Fraction at Near-Optimal H/Pu Ratio Case        H/Pu    Reflector      VF        keff                    ks CASED70H8              ICV = 70%      1.00      0.9307        0.0009      0.9325 CASED70H8V95              poly/29%      0.95      0.9292        0.0009      0.9310 water/1% Be CASED70H8V90                            0.90      0.9252        0.0009      0.9270 at VF given CASED70H8V75            OCA = 25%      0.75      0.9143        0.0009      0.9161 800 CASED70H8V50              poly/74%      0.50      0.8893        0.0009      0.8911 water/1% Be CASED70H8V25              at VF given    0.25      0.8382        0.0011      0.8404 CASED70H8V10            Int = water at  0.10      0.7828        0.0010      0.7848 CASED70H8V00              VF given        0      0.8501        0.0010      0.8521 Table 6.4 Infinite Array Variation 1, HAC, Case D, 325 FGE; Variation of H/Pu Ratio at Reflector Volume Fraction to Maximize Interaction while Maintaining Reflection Case        Variation    H/Pu        Reflector      keff                ks D1BOFF70H6                    600        ICV = 70%    0.9037      0.0010  0.9057 D1BOFF70H7                    700        poly/29%    0.9125      0.0011  0.9147 water/1% Be D1BOFF70H8          1        800        at VF=1.0    0.9144      0.0008  0.9160 D1BOFF70H9                    900      OCA = Int =    0.9153      0.0009  0.9171 D1BOFF70H10                    1,000          Void      0.9131      0.0008  0.9147 6.4-24
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 6.5 Critical Benchmark Experiments The KENO-V.a Monte Carlo criticality code 1 has been used extensively in criticality evaluations. The 238 energy-group, ENDF-B/V cross-section library 2 employed here has been selected based on its relatively fine neutron energy group structure. This section justifies the validity of this computation tool and data library combination for application to the HalfPACT package criticality analysis.
The ORNL USLSTATS code, described in Appendix C, Users Manual for USLSTATS V1.0, of NUREG/CR-6361 3, is used to establish an upper subcriticality limit, USL, for the analysis.
Computed multiplication factors, keff, for the HalfPACT package are deemed to be adequately subcritical if the computed value of keff plus two standard deviations is below the USL as follows:
ks = keff + 2 < USL The USL includes the combined effects of code bias, uncertainty in the benchmark experiments, uncertainty in the computational evaluation of the benchmark experiments, and an administrative margin of subcriticality. The USL is determined using the confidence band with administrative margin technique (USLSTATS Method 1).
The result of the statistical analysis of the benchmark experiments is a USL of 0.9382. Due to the significant positive bias exhibited by the code and library for the benchmark experiments, the USL is constant with respect to the various parameters selected for the benchmark analysis.
6.5.1 Benchmark Experiments and Applicability A total of 196 benchmark experiments of water-reflected solutions of plutonium nitrate are evaluated using the KENO-V.a Monte Carlo criticality code with the SCALE-PC v4.4a 4, 238 energy-group, ENDF-B/V cross-section library. The benchmark cases are evaluated with respect to three independent parameters: 1) the H/Pu ratio, 2) the average fission energy group (AEG),
and 3) the ratio of Pu-240 to total Pu.
Detailed descriptions of the benchmark experiments are obtained from the OECD Nuclear Energy Agencys International Handbook of Evaluated Criticality Safety Benchmark Experiments 5. The critical experiments selected for this analysis are presented in Table 6.5-1.
Experiments with beryllium and Pu as the fissile component are not available. The only experiments with beryllium in the thermal energy range identified from the OECD Handbook 1
L. M. Petrie and N. F. Landers, KENO-V.a: An Improved Monte Carlo Criticality Program with Supergrouping, ORNL/NUREG/CSD-2/V2/R6, Volume 2, Section F11, March 2000.
2 W. C. Jordan and S. M. Bowman, Scale Cross-Section Libraries, ORNL/NUREG/CSD-2/V3/R6, Volume 3, Section M4, March 2000.
3 J. J. Lichtenwalter, S. M. Bowman, M. D. DeHart, C. M. Hopper, Criticality Benchmark Guide for Light-Water-Reactor Fuel in Transportation and Storage Packages, NUREG/CR-6361, ORNL/TM-13211, March 1997.
4 Oak Ridge National Laboratory (ORNL), SCALE 4.4a: Modular Code System for Performing Standardized Computer Analyses for Licensing Evaluation for Workstations and Personal Computers, ORNL/NUREG/CSD-2/R6, March 2000.
5 OECD Nuclear Energy Agency, International Handbook of Evaluated Criticality Safety Benchmark Experiments, NEA/NSC/DOC(95)03, September 2002.
6.5-1
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 contained U-233 as the fissile isotope. Thus, 31 benchmarks with U-233 and beryllium in the thermal energy range and 15 benchmarks with U-233 and no beryllium also in the thermal energy range were evaluated. With respect to validation of polyethylene, CH2, in the models, some of the U-233 benchmarks contained polyethylene and some of the plutonium experiments contained Plexiglas, which also contains carbon. All criticality models of the HalfPACT package fall within the range of applicability of the benchmark experiments for the H/Pu ratio and AEG trending parameters as follows:
Range of Applicability for Trending Parameters 45  H/Pu Ratio  2,730 173  AEG  220 4.95 x 10-3  Pu-240/Pu Ratio  2.32 x 10-1 The intent of using the Pu-240/Pu ratio is to demonstrate the validity of an extension of the range of applicability of this parameter to the HalfPACT package criticality models. The Case A models include a Pu-240/Pu Ratio of up to 6.6 x 10-2, which is within the range of applicability.
Only thermal benchmark experiments are analyzed. Criticality analysis of the HalfPACT package and package arrays demonstrate that multiplication factors are insignificant when the package contents are unmoderated.
6.5.2 Details of Benchmark Calculations A total of 196 experimental benchmarks with Pu in the thermal energy range were evaluated with the KENO-V.a code with the SCALE-PC v4.4a, 238 group, ENDF-B/V cross-section library. Detailed descriptions of these experiments are found in the OECD Handbook. A summary of the experiment titles is provided in Table 6.5-1. The benchmark results were evaluated using the USLSTATS program as discussed in the next section.
6.5.3 Results of Benchmark Calculations Table 6.5-2 summarizes the trending parameter values, computed keff values, and uncertainties for each case. The uncertainty value, c, assigned to each case is a combination of the experimental uncertainty for each experiment, exp, and the Monte Carlo uncertainty associated with the particular computational evaluation of the case, comp, or:
c = (exp2 + comp2)1/2 These values were input into the USLSTATS program in addition to the following parameters:
* P, proportion of population falling above lower tolerance level = 0.995
* 1-, confidence on fit = 0.95
*  , confidence on proportion P = 0.95
* xmin, minimum value of AEG for which USL correlation are computed = N/A, minimum of supplied data used by code 6.5-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
* xmax, maximum value of AEG for which USL correlation are computed = N/A, maximum of supplied data used by code
* eff, estimate in average standard deviation of all input values of keff = -1.0, use supplied values
* km, administrative margin used to ensure subcriticality = 0.05.
This data is followed by triplets of trending parameter value, computed keff, and uncertainty for each case. The USL Method 1 result was chosen which performs a confidence band analysis on the data for the trending parameter.
Three trending parameters are identified for determination of the bias. First, the AEG is used in order to characterize any code bias with respect to neutron spectral effects. The USL is calculated vs. AEG separately for the Pu experiments, U-233 experiments with beryllium and U-233 experiments without beryllium in addition to the combined results of the Pu and U-233 with beryllium experiments. Because the U-233 fissile isotope introduces a component that is not relative to the calculations performed for the HalfPACT and may have a distinct bias of its own, comparison of the USL for the U-233 experiments with beryllium to the USL for those without beryllium allows the effect of the beryllium reflector to be separated from the effect of the U-233 isotope. Next, the H/Pu ratio of each experimental case containing Pu is used in order to characterize the material and geometric properties of each sphere. Finally, since all the Pu experiments include Pu-240 to some extent and the HalfPACT models contain varying amount of Pu-240, a trending analysis of the results of the Pu experiments with respect to Pu-240/Pu ratio is performed. The U-233 results are not considered in the trending with respect to H/Pu as the optimum H/Pu range will be significantly different for a U-233 system vs. a Pu system. For obvious reasons, the U-233 results are also not considered in the trending with respect to the Pu-240/Pu ratio.
The USLs calculated using USLSTATS Method 1 for the benchmark combinations discussed above are tabulated in Table 6.5-3. The USL calculated based on the combined results of the U-233 with beryllium and Pu experiments of 0.9382 is chosen as the USL for this analysis. This USL value is ~0.001 below that of the Pu experiments alone. The 233U benchmarks without Be result in a lower USL (0.0032) than calculated from the U-233 benchmark results with beryllium.
This difference is greater than the experimental uncertainty of each benchmark case (~0.001).
Both of the U-233 USL values are lower than the Pu experiment USL values indicating that the U-233 isotope in the experiments has a more significant effect on the USL than the beryllium.
Thus, the USL based on the combined results of the U-233 with beryllium and Pu experiments chosen adequately accounts for any bias attributable to beryllium. In addition, the USLs calculated for the Pu experiments using either H/X or the Pu-240/Pu ratio as the trending parameter do not differ significantly from the Pu USL vs. AEG and are bounded by the chosen USL value of 0.9382. USLSTATS calculated constant USL values with respect to H/Pu and Pu-240/Pu ratio indicating no appreciable trend with respect to these parameters.
6.5-3
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 Table 6.5 Benchmark Experiment Description with Experimental Uncertainties Series                                              Title PU-SOL-THERM-001    Water-reflected 11.5-inch diameter spheres of plutonium nitrate solutions PU-SOL-THERM-002    Water-reflected 12-inch diameter spheres of plutonium nitrate solutions PU-SOL-THERM-003    Water-reflected 13-inch diameter spheres of plutonium nitrate solutions Water-reflected 14-inch diameter spheres of plutonium nitrate solutions PU-SOL-THERM-004 0.54% to 3.43% Pu-240 Water-reflected 14-inch diameter spheres of plutonium nitrate solutions PU-SOL-THERM-005 4.05% and 4.40% Pu-240 PU-SOL-THERM-006    Water-reflected 15-inch diameter spheres of plutonium nitrate solutions Water-reflected 11.5-inch diameter spheres partly filled with plutonium PU-SOL-THERM-007 nitrate solutions PU-SOL-THERM-009    Unreflected 48-inch diameter sphere of plutonium nitrate solution Water-reflected 9-, 10-, 11-, and 12-inch diameter cylinders of plutonium PU-SOL-THERM-010 nitrate solutions PU-SOL-THERM-011    Bare 16- and 18-inch diameter spheres of plutonium nitrate solutions PU-SOL-THERM-014    Interacting cylinders of 300-mm diameter with plutonium nitrate solution (115.1gPu/l) in air PU-SOL-THERM-015    Interacting cylinders of 300-mm diameter with plutonium nitrate solution (152.5gPu/l) in air PU-SOL-THERM-016    Interacting cylinders of 300-mm and 256-mm diameters with plutonium nitrate solution (152.5 and 115.1gPu/l) and nitric acid (2n) in air PU-SOL-THERM-017    Interacting cylinders of 256-mm and 300-mm diameters with plutonium nitrate solution (115.1gPu/l) in air PU-SOL-THERM-020    Water-reflected and water-cadmium reflected 14-inch diameter spheres of plutonium nitrate solutions PU-SOL-THERM-021    Water-reflected and bare 15.2-inch diameter spheres of plutonium nitrate solutions PU-SOL-THERM-024    Slabs of plutonium nitrate solutions reflected by 1-inch thick Plexiglas U233-SOL-THERM-001    Unreflected spheres of 233U nitrate solutions U233-SOL-THERM-003    Paraffin-reflected 5-, 5.4-, 6-, 6.6-, 7.5- 8-, 8.5-, 9- and 12-inch diameter cylinders of 233U uranyl fluoride solutions U233-SOL-THERM-015    Uranyl-fluoride (233U) solutions in spherical stainless steel vessels with reflectors of Be, CH2, and Be-CH2 composites 6.5-4
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Table 6.5 Benchmark Case Parameters and Computed Results Experiment Pu-240/ Uncertainty Case Name          keff  comp      AEG    H/X  Pu Ratio      exp PUST001_CASE_1      1.0080  0.0010    212.494 352.9  0.04650    0.0050 PUST001_CASE_2      1.0100  0.0010    209.961 258.1  0.04650    0.0050 PUST001_CASE_3      1.0133  0.0010    207.777 204.1  0.04650    0.0050 PUST001_CASE_4      1.0073  0.0010    206.439  181  0.04650    0.0050 PUST001_CASE_5      1.0111  0.0011    205.757 171.2  0.04650    0.0050 PUST001_CASE_6      1.0089  0.0010    195.766  86.7  0.04650    0.0050 PUST002_CASE_1      1.0074  0.0010    214.693  508  0.03110    0.0047 PUST002_CASE_2      1.0088  0.0011    214.457 489.2  0.03110    0.0047 PUST002_CASE_3      1.0074  0.0010    213.798 437.3  0.03110    0.0047 PUST002_CASE_4      1.0103  0.0010    213.343 407.5  0.03110    0.0047 PUST002_CASE_5      1.0125  0.0011    212.898 380.6  0.03110    0.0047 PUST002_CASE_6      1.0099  0.0010    211.974 333.5  0.03110    0.0047 PUST002_CASE_7      1.0101  0.0010    211.146 299.3  0.03110    0.0047 PUST003_CASE_1      1.0089  0.0010    216.630 774.1  0.01750    0.0047 PUST003_CASE_2      1.0076  0.0011    216.438 742.7  0.01750    0.0047 PUST003_CASE_3      1.0103  0.0010    216.055 677.2  0.03110    0.0047 PUST003_CASE_4      1.0094  0.0010    215.948 660.5  0.03110    0.0047 PUST003_CASE_5      1.0097  0.0010    215.535 607.2  0.03110    0.0047 PUST003_CASE_6      1.0099  0.0011    214.960 545.3  0.03110    0.0047 PUST003_CASE_7      1.0121  0.0009    216.482 714.8  0.03110    0.0047 PUST003_CASE_8      1.0091  0.0011    216.321 692.1  0.03110    0.0047 PUST004_CASE_1      1.0080  0.0010    217.470 981.7  0.00538    0.0047 PUST004_CASE_2      1.0032  0.0009    217.408 898.6  0.04180    0.0047 PUST004_CASE_3      1.0059  0.0008    217.241  864  0.04500    0.0047 PUST004_CASE_4      1.0033  0.0009    217.034  842  0.03260    0.0047 PUST004_CASE_5      1.0043  0.0010    217.257 780.2  0.03630    0.0047 PUST004_CASE_6      1.0074  0.0009    217.195  668  0.00495    0.0047 PUST004_CASE_7      1.0104  0.0010    217.030 573.3  0.00495    0.0047 PUST004_CASE_8      1.0040  0.0009    216.917  865  0.00504    0.0047 PUST004_CASE_9      1.0041  0.0009    216.580 872.2  0.01530    0.0047 6.5-5
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 Experiment Pu-240/ Uncertainty Case Name          keff  comp      AEG    H/X  Pu Ratio      exp PUST004_CASE_10      1.0078  0.0009    215.881  971.6  0.02510    0.0047 PUST004_CASE_11      1.0041  0.0010    215.106  929.6  0.02330    0.0047 PUST004_CASE_12      1.0094  0.0009    217.031  884.1  0.03160    0.0047 PUST004_CASE_13      1.0042  0.0009    217.074  925.5  0.03350    0.0047 PUST005_CASE_1      1.0072  0.0010    217.069  866.4  0.04030    0.0047 PUST005_CASE_2      1.0084  0.0009    216.909  832.7  0.04030    0.0047 PUST005_CASE_3      1.0092  0.0009    216.749  800.7  0.04030    0.0047 PUST005_CASE_4      1.0091  0.0010    216.360  734.4  0.04030    0.0047 PUST005_CASE_5      1.0102  0.0010    215.906  666.1  0.04030    0.0047 PUST005_CASE_6      1.0112  0.0010    215.451  607.9  0.04030    0.0047 PUST005_CASE_7      1.0099  0.0010    215.004  557.2  0.04030    0.0047 PUST005_CASE_8      1.0024  0.0010    216.903  830.6  0.04030    0.0047 PUST005_CASE_9      1.0078  0.0010    216.687  788.9  0.04030    0.0047 PUST006_CASE_1      1.0059  0.0008    217.615 1028.2  0.03110    0.0035 PUST006_CASE_2      1.0079  0.0009    217.459  986.2  0.03110    0.0035 PUST006_CASE_3      1.0072  0.0010    217.147  910.9  0.03110    0.0035 PUST007_CASE_2      1.0090  0.0011    198.911  102.6  0.04570    0.0047 PUST007_CASE_3      1.0024  0.0010    199.553 110.11  0.04570    0.0047 PUST007_CASE_5      1.0099  0.0010    209.885  253.3  0.04570    0.0047 PUST007_CASE_6      1.0054  0.0011    209.689  247.3  0.04570    0.0047 PUST007_CASE_7      1.0072  0.0010    209.816  250.5  0.04570    0.0047 PUST007_CASE_8      1.0007  0.0012    209.577  246.5  0.04570    0.0047 PUST007_CASE_9      0.9996  0.0011    209.628  246.5  0.04570    0.0047 PUST007_CASE_10      1.0009  0.0011    210.426  275.5  0.04570    0.0047 PUST009_CASE_1      1.0202  0.0007    219.730 2579.3  0.02510    0.0033 PUST009_CASE_2      1.0242  0.0005    219.819 2706.5  0.02510    0.0033 PUST009_CASE_3      1.0232  0.0006    219.830 2729.8  0.02510    0.0033 PUST010_CASE_1.11    1.0158  0.0011    219.830  471.3  0.02840    0.0048 PUST010_CASE_1.12    1.0125  0.0009    214.122 527.7  0.02890    0.0048 PUST010_CASE_1.9      1.0183  0.0012    214.895  259.3  0.02840    0.0048 PUST010_CASE_2.11    1.0124  0.0011    210.075 542.3  0.02840    0.0048 PUST010_CASE_2.12    1.0136  0.0010    214.882  600.5  0.02890    0.0048 6.5-6
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 Experiment Pu-240/ Uncertainty Case Name          keff  comp      AEG    H/X  Pu Ratio      exp PUST010_CASE_2.9      1.0140  0.0011    215.514  346.8  0.02840    0.0048 PUST010_CASE_3.11    1.0128  0.0011    212.361  542.3  0.02840    0.0048 PUST010_CASE_3.12    1.0208  0.0009    215.036  707  0.02890    0.0048 PUST010_CASE_3.9      1.0120  0.0010    216.250  470.4  0.02840    0.0048 PUST010_CASE_4.11    1.0055  0.0011    214.300  588.7  0.02840    0.0048 PUST010_CASE_4.12    1.0142  0.0009    215.366  825.1  0.02890    0.0048 PUST010_CASE_5.11    1.0068  0.0010    216.852  646.5  0.02840    0.0048 PUST010_CASE_6.11    1.0176  0.0012    215.739  402.3  0.02890    0.0048 PUST010_CASE_7.11    1.0065  0.0010    213.340  519.8  0.02890    0.0048 PUST011_CASE_1.16    1.0135  0.0010    214.790  733  0.04150    0.0052 PUST011_CASE_1.18    1.0001  0.0009    215.818 1157.3  0.04180    0.0052 PUST011_CASE_2.16    1.0196  0.0010    217.686  705.5  0.04150    0.0052 PUST011_CASE_2.18    1.0065  0.0011    215.633 1103.2  0.04180    0.0052 PUST011_CASE_3.16    1.0213  0.0010    217.509  662.8  0.04150    0.0052 PUST011_CASE_3.18    1.0027  0.0010    215.281 1109.8  0.04180    0.0052 PUST011_CASE_4.16    1.0139  0.0011    217.525  653.4  0.04150    0.0052 PUST011_CASE_4.18    0.9991  0.0011    215.196 1053.7  0.04180    0.0052 PUST011_CASE_5.16    1.0113  0.0010    217.313  550.7  0.04150    0.0052 PUST011_CASE_5.18    1.0099  0.0010    214.156  995.4  0.04180    0.0052 PUST011_CASE_6.18    1.0068  0.0010    217.071  870.4  0.04180    0.0052 PUST011_CASE_7.18    1.0050  0.0010    216.471 1056.4  0.04180    0.0052 PUST014_CASE_1      1.0068  0.0012    205.455  210.2  0.04230    0.0032 PUST014_CASE_3      1.0065  0.0010    205.477  210.2  0.04230    0.0032 PUST014_CASE_4      1.0079  0.0011    205.504  210.2  0.04230    0.0032 PUST014_CASE_5      1.0065  0.0011    205.510  210.2  0.04230    0.0032 PUST014_CASE_6      1.0073  0.0013    205.516  210.2  0.04230    0.0032 PUST014_CASE_7      1.0082  0.0012    205.434  210.2  0.04230    0.0043 PUST014_CASE_8      1.0051  0.0012    205.462  210.2  0.04230    0.0032 PUST014_CASE_9      1.0068  0.0012    205.477  210.2  0.04230    0.0032 PUST014_CASE_10      1.0060  0.0011    205.499  210.2  0.04230    0.0032 PUST014_CASE_11      1.0046  0.0010    205.526  210.2  0.04230    0.0032 PUST014_CASE_12      1.0076  0.0010    205.522  210.2  0.04230    0.0032 6.5-7
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Experiment Pu-240/ Uncertainty Case Name          keff  comp      AEG    H/X  Pu Ratio      exp PUST014_CASE_13      1.0080  0.0011    205.420 210.2  0.04230    0.0043 PUST014_CASE_14      1.0062  0.0011    205.458 210.2  0.04230    0.0043 PUST014_CASE_15      1.0067  0.0011    205.507 210.2  0.04230    0.0043 PUST014_CASE_16      1.0057  0.0011    205.512 210.2  0.04230    0.0043 PUST014_CASE_17      1.0033  0.0011    205.506 210.2  0.04230    0.0043 PUST014_CASE_18      1.0070  0.0011    205.430 210.2  0.04230    0.0043 PUST014_CASE_19      1.0045  0.0011    205.469 210.2  0.04230    0.0043 PUST014_CASE_20      1.0061  0.0011    205.487 210.2  0.04230    0.0043 PUST014_CASE_21      1.0066  0.0012    205.514 210.2  0.04230    0.0043 PUST014_CASE_22      1.0060  0.0012    205.527 210.2  0.04230    0.0043 PUST014_CASE_23      1.0048  0.0012    205.530 210.2  0.04230    0.0043 PUST014_CASE_24      1.0080  0.0012    205.393 210.2  0.04230    0.0043 PUST014_CASE_25      1.0042  0.0011    205.445 210.2  0.04230    0.0043 PUST014_CASE_26      1.0066  0.0011    205.490 210.2  0.04230    0.0043 PUST014_CASE_27      1.0044  0.0011    205.504 210.2  0.04230    0.0043 PUST014_CASE_28      1.0052  0.0011    205.534 210.2  0.04230    0.0043 PUST014_CASE_29      1.0050  0.0011    205.525 210.2  0.04230    0.0043 PUST014_CASE_30      1.0060  0.0010    205.416 210.2  0.04230    0.0043 PUST014_CASE_31      1.0046  0.0011    205.444 210.2  0.04230    0.0043 PUST014_CASE_33      1.0021  0.0011    205.446 210.2  0.04230    0.0043 PUST014_CASE_34      1.0045  0.0011    205.480 210.2  0.04230    0.0043 PUST015_CASE_1      1.0065  0.0010    201.243 155.3  0.04230    0.0038 PUST015_CASE_2      1.0069  0.0011    201.272 155.3  0.04230    0.0038 PUST015_CASE_3      1.0060  0.0011    201.289 155.3  0.04230    0.0038 PUST015_CASE_4      1.0056  0.0012    201.324 155.3  0.04230    0.0038 PUST015_CASE_5      1.0072  0.0011    201.311 155.3  0.04230    0.0038 PUST015_CASE_6      1.0078  0.0012    201.327 155.3  0.04230    0.0038 PUST015_CASE_7      1.0078  0.0011    201.209 155.3  0.04230    0.0047 PUST015_CASE_8      1.0056  0.0011    201.255 155.3  0.04230    0.0047 PUST015_CASE_9      1.0062  0.0012    201.292 155.3  0.04230    0.0047 PUST015_CASE_10      1.0060  0.0011    201.333 155.3  0.04230    0.0047 PUST015_CASE_11      1.0012  0.0010    201.196 155.3  0.04230    0.0047 6.5-8
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Experiment Pu-240/ Uncertainty Case Name          keff  comp      AEG    H/X  Pu Ratio      exp PUST015_CASE_12      1.0053  0.0011    201.280 155.3  0.04230    0.0047 PUST015_CASE_13      1.0084  0.0010    201.307 155.3  0.04230    0.0047 PUST015_CASE_14      1.0065  0.0012    201.335 155.3  0.04230    0.0047 PUST015_CASE_15      1.0082  0.0013    201.196 155.3  0.04230    0.0047 PUST015_CASE_16      1.0064  0.0010    201.222 155.3  0.04230    0.0047 PUST015_CASE_17      1.0067  0.0010    201.299 155.3  0.04230    0.0047 PUST016_CASE_1      1.0077  0.0011    201.225 155.3  0.04230    0.0043 PUST016_CASE_2      1.0048  0.0011    201.265 155.3  0.04230    0.0043 PUST016_CASE_3      1.0072  0.0011    201.295 155.3  0.04230    0.0043 PUST016_CASE_4      1.0075  0.0011    201.318 155.3  0.04230    0.0043 PUST016_CASE_5      1.0054  0.0012    205.463 210.2  0.04230    0.0038 PUST016_CASE_6      1.0047  0.0011    205.476 210.2  0.04230    0.0038 PUST016_CASE_7      1.0093  0.0013    205.511 210.2  0.04230    0.0038 PUST016_CASE_8      1.0072  0.0011    205.508 210.2  0.04230    0.0038 PUST016_CASE_9      1.0070  0.0012    205.607 210.2  0.04230    0.0033 PUST016_CASE_10      1.0065  0.0012    205.556 210.2  0.04230    0.0033 PUST016_CASE_11      1.0063  0.0011    205.516 210.2  0.04230    0.0033 PUST017_CASE_1      1.0076  0.0011    205.535 210.2  0.04230    0.0038 PUST017_CASE_2      1.0050  0.0011    205.488 210.2  0.04230    0.0038 PUST017_CASE_3      1.0041  0.0011    205.492 210.2  0.04230    0.0038 PUST017_CASE_4      1.0054  0.0012    205.482 210.2  0.04230    0.0038 PUST017_CASE_5      1.0066  0.0012    205.488 210.2  0.04230    0.0038 PUST017_CASE_6      1.0056  0.0011    205.479 210.2  0.04230    0.0038 PUST017_CASE_7      1.0069  0.0011    205.485 210.2  0.04230    0.0038 PUST017_CASE_8      1.0051  0.0011    205.497 210.2  0.04230    0.0038 PUST017_CASE_9      1.0071  0.0012    205.525 210.2  0.04230    0.0038 PUST017_CASE_10      1.0060  0.0011    205.500 210.2  0.04230    0.0038 PUST017_CASE_11      1.0050  0.0011    205.531 210.2  0.04230    0.0038 PUST017_CASE_12      1.0057  0.0011    205.509 210.2  0.04230    0.0038 PUST017_CASE_13      1.0047  0.0011    205.490 210.2  0.04230    0.0038 PUST017_CASE_14      1.0049  0.0013    205.487 210.2  0.04230    0.0038 PUST017_CASE_15      1.0072  0.0012    205.533 210.2  0.04230    0.0038 6.5-9
 
HalfPACT Safety Analysis Report                            Rev. 9, August 2022 Experiment Pu-240/ Uncertainty Case Name          keff  comp      AEG  H/X  Pu Ratio      exp PUST017_CASE_16      1.0075  0.0010    205.522 210.2  0.04230    0.0038 PUST017_CASE_17      1.0068  0.0012    205.519 210.2  0.04230    0.0038 PUST017_CASE_18      1.0056  0.0010    205.487 210.2  0.04230    0.0038 PUST020_CASE_1      1.0075  0.0010    215.482 596.5  0.04570    0.0059 PUST020_CASE_2      1.0117  0.0010    215.622 615.6  0.04570    0.0059 PUST020_CASE_3      1.0049  0.0009    216.499 743.8  0.04570    0.0059 PUST020_CASE_5      1.0074  0.0010    213.992 462.9  0.04570    0.0059 PUST020_CASE_6      1.0078  0.0009    213.637 450.5  0.04570    0.0059 PUST020_CASE_7      1.0022  0.0009    216.277 722.9  0.04570    0.0059 PUST020_CASE_8      1.0066  0.0011    210.650 341.1  0.04570    0.0059 PUST020_CASE_9      1.0004  0.0010    214.048 543.2  0.04570    0.0059 PUST021_CASE_7      1.0109  0.0011    215.405  662  0.04570    0.0032 PUST021_CASE_8      1.0044  0.0010    197.712  125  0.04570    0.0065 PUST021_CASE_9      1.0117  0.0010    215.136  634  0.04570    0.0032 PUST021_CASE_10      1.0123  0.0008    218.033 1107  0.04570    0.0025 PUST024_CASE_1      1.0018  0.0010    191.676  87.5  0.18400    0.0062 PUST024_CASE_2      0.9999  0.0009    191.828  87.5  0.18400    0.0062 PUST024_CASE_3      1.0002  0.0011    191.933  87.5  0.18400    0.0062 PUST024_CASE_4      1.0020  0.0010    192.026  87.5  0.18400    0.0062 PUST024_CASE_5      0.9986  0.0011    192.017  87.5  0.18400    0.0062 PUST024_CASE_6      0.9988  0.0009    173.477  44.9  0.18400    0.0077 PUST024_CASE_7      1.0072  0.0010    201.097 143.9  0.18400    0.0053 PUST024_CASE_8      1.0073  0.0010    201.200 143.9  0.18400    0.0053 PUST024_CASE_9      1.0068  0.0010    201.253 143.9  0.18400    0.0053 PUST024_CASE_10      1.0090  0.0010    201.353 143.9  0.18400    0.0053 PUST024_CASE_11      1.0065  0.0011    201.418 143.9  0.18400    0.0053 PUST024_CASE_12      1.0069  0.0010    201.452 143.9  0.18400    0.0053 PUST024_CASE_13      1.0066  0.0010    201.493 143.9  0.18400    0.0053 PUST024_CASE_14      1.0019  0.0011    197.708 115.8  0.23200    0.0053 PUST024_CASE_15      1.0033  0.0012    197.781 115.8  0.23200    0.0053 PUST024_CASE_16      1.0017  0.0009    197.845 115.8  0.23200    0.0053 PUST024_CASE_17      1.0026  0.0010    197.990 115.8  0.23200    0.0053 6.5-10
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 Experiment Pu-240/ Uncertainty Case Name          keff  comp      AEG    H/X  Pu Ratio      exp PUST024_CASE_18      1.0085  0.0010    212.039  367.3  0.18400    0.0051 PUST024_CASE_19      1.0079  0.0009    212.057  367.3  0.18400    0.0051 PUST024_CASE_20      1.0100  0.0010    212.074  367.3  0.18400    0.0051 PUST024_CASE_21      1.0075  0.0010    212.106  367.3  0.18400    0.0051 PUST024_CASE_22      1.0054  0.0010    212.142  367.3  0.18400    0.0051 PUST024_CASE_23      1.0068  0.0011    212.166  367.3  0.18400    0.0051 233ST001CASE_1      0.9975  0.0008    218.415 1531.5    N/A      0.0031 233ST001CASE_2      0.9959  0.0008    218.224 1471.7    N/A      0.0033 233ST001CASE_3      0.9955  0.0007    218.055 1420.1    N/A      0.0033 233ST001CASE_4      0.9970  0.0007    217.875 1369.7    N/A      0.0033 233ST001CASE_5      0.9956  0.0008    217.697 1325.4    N/A      0.0033 233ST003CASE_40      1.0029  0.0011    192.780  74.1    N/A      0.0087 233ST003CASE_41      1.0164  0.0011    191.195  74.1    N/A      0.0151 233ST003CASE_42      1.0002  0.0013    191.824  74.1    N/A      0.0087 233ST003CASE_45      1.0040  0.0013    180.246  45.9    N/A      0.0126 233ST003CASE_55      1.0102  0.0011    176.271  39.4    N/A      0.0122 233ST003CASE_57      1.0196  0.0012    204.026  154    N/A      0.0087 233ST003CASE_58      1.0119  0.0012    209.393  250    N/A      0.0087 233ST003CASE_61      1.0056  0.0011    211.723  329    N/A      0.0087 233ST003CASE_62      1.0079  0.0012    213.031  396    N/A      0.0087 233ST003CASE_65      1.0039  0.0010    216.519  775    N/A      0.0087 233ST015_CASE_1      0.9928  0.0012    175.241  51.58    N/A      0.0075 233ST015_CASE_2      0.9869  0.0013    173.581  51.58    N/A      0.0070 233ST015_CASE_3      0.9863  0.0012    181.133  51.58    N/A      0.0068 233ST015_CASE_4      0.9863  0.0012    181.133  51.58    N/A      0.0041 233ST015_CASE_5      0.9844  0.0012    172.140  51.58    N/A      0.0055 233ST015_CASE_6      0.9750  0.0012    171.626  51.58    N/A      0.0099 233ST015_CASE_7      0.9807  0.0012    179.879  51.58    N/A      0.0070 233ST015_CASE_8      0.9719  0.0012    171.311  51.58    N/A      0.0067 233ST015_CASE_9      0.9664  0.0013    171.019  51.58    N/A      0.0050 233ST015_CASE_10      0.9841  0.0012    174.951  51.58    N/A      0.0051 233ST015_CASE_11      0.9937  0.0012    181.620  64.23    N/A      0.0075 6.5-11
 
HalfPACT Safety Analysis Report                                        Rev. 9, August 2022 Experiment Pu-240/ Uncertainty Case Name              keff    comp      AEG      H/X    Pu Ratio        exp 233ST015_CASE_12          0.9942    0.0012      180.243    64.23      N/A          0.0069 233ST015_CASE_13          0.9924    0.0011      179.562    64.23      N/A          0.0069 233ST015_CASE_14          0.9930    0.0011      187.157    64.23      N/A          0.0036 233ST015_CASE_15          0.9881    0.0012      178.911    64.23      N/A          0.0060 233ST015_CASE_16          0.9877    0.0013      178.599    64.23      N/A          0.0043 233ST015_CASE_17          0.9924    0.0012      186.084    64.23      N/A          0.0029 233ST015_CASE_18          0.9727    0.0014      178.045    64.23      N/A          0.0056 233ST015_CASE_19          0.9728    0.0012      177.964    64.23      N/A          0.0052 233ST015_CASE_20          0.9969    0.0011      193.458  102.54      N/A          0.0079 233ST015_CASE_21          0.9992    0.0012      192.290  102.54      N/A          0.0070 233ST015_CASE_22          0.9966    0.0011      191.669  102.54      N/A          0.0062 233ST015_CASE_23          0.9949    0.0011      191.140  102.54      N/A          0.0055 233ST015_CASE_24          0.9901    0.0013      190.850  102.54      N/A          0.0051 233ST015_CASE_25          0.9917    0.0012      196.919  102.54      N/A          0.0023 233ST015_CASE_26          0.9964    0.0011      204.143    199.4      N/A          0.0066 233ST015_CASE_27          0.9982    0.0011      203.709    199.4      N/A          0.0063 233ST015_CASE_28          0.9948    0.0010      203.459    199.4      N/A          0.0058 233ST015_CASE_29          0.9928    0.0012      203.220    199.4      N/A          0.0051 233ST015_CASE_30          0.9940    0.0011      203.118    199.4      N/A          0.0048 233ST015_CASE_31          0.9946    0.0012      203.041    199.4      N/A          0.0055 X refers to Pu or U-233 as applicable for the benchmark cases All cases were run with 1000 neutrons per generation for 1000 generations with the initial 50 generations skipped.
6.5-12
 
HalfPACT Safety Analysis Report                                          Rev. 9, August 2022 Table 6.5 Calculation of USL Benchmark Set          Number of        USL vs.        USL vs.      USL vs.
Cases            AEG            H/X        Pu-240/Pu U-233 without Be            15          0.9270          N/A            N/A U-233 with Be              31          0.9302          N/A            N/A (204.14)
Pu                196          0.9395        0.9393        0.9395 Pu + U-233 with Be          227          0.9382          N/A            N/A Calculated at maximum AEG of the set 204.14. USL increases with AEG such that this is conservative for the AEG of the calculations (~217)
Range of applicability is 195.928 < AEG < 219.83 6.5-13
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
6.5-14
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 7.0 OPERATING PROCEDURES 7.1 Procedures for Loading the Package This section delineates the procedures for loading a payload into the HalfPACT packaging, and leakage rate testing the inner containment vessel (ICV) and, optionally, the outer confinement vessel (OCV). Hereafter, reference to specific HalfPACT packaging components may be found in Appendix 1.3.1, Packaging General Arrangement Drawings.
The loading operation shall be performed in a dry environment. In the event of precipitation during outdoor loading operations, precautions, such as covering the OCV and ICV cavities shall be implemented to prevent water or precipitation from entering the cavities. If precipitation enters the cavities, the free-standing water shall be removed prior to loading the payload.
Based on the current configuration of the HalfPACT packaging when preparing for loading, begin at the section applicable to the following criteria:
* If the HalfPACT package will be loaded while on the transport trailer or railcar, proceed directly to Section 7.1.2, Outer Confinement Assembly (OCA) Lid Removal.
* If the outer confinement assembly (OCA) lid has already been removed, proceed directly to Section 7.1.3, Inner Containment Vessel (ICV) Lid Removal.
* If both the OCA and ICV lids have already been removed, proceed directly to Section 7.1.4, Loading the Payload into the HalfPACT Package.
7.1.1      Removal of the HalfPACT Package from the Transport Trailer/Railcar
: 1. Uncover the forklift pockets located at the base of the OCA body.
: 2. Disengage each of the four (4) tie-down devices on the transport trailer or railcar from the corresponding tie-down lugs on the package.
CAUTION: Failure to disengage the tie-down devices may cause damage to the packaging and/or transport trailer/railcar.
: 3. Using a forklift of appropriate size, position the forklifts forks inside the forklift pockets.
: 4. Lift the package from the transport trailer or railcar and move the package to the loading station.
: 5. Place the package in the loading station and remove the forklift.
7.1.2      Outer Confinement Assembly (OCA) Lid Removal
: 1. If necessary, clean the surfaces around the joint between the OCA lid and body as required.
: 2. Remove the OCV seal test port access plug, OCV seal test port thermal plug, and OCV seal test port plug.
: 3. Remove the OCV vent port access plug, OCV vent port thermal plug, and OCV vent port cover.
: 4. Remove the OCV vent port plug to vent the OCV cavity to ambient atmospheric pressure.
7.1-1
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022
: 5. Remove the six 1/2-inch lock bolts (socket head cap screws) from the exterior of the OCA thermal shield.
: 6. Optionally install a vacuum pump to the OCV vent port and evacuate the OCV cavity sufficiently to allow the OCV locking ring to freely rotate. Rotate the OCV locking ring approximately 10&#xba; counterclockwise until the exterior alignment mark indicates the unlocked position. If used, disconnect the vacuum system and equalize pressure to the OCV cavity.
: 7. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the OCA lid. Engage the lift fixture and remove the OCA lid from the OCA body. Store the OCA lid in a manner such that potential damage to the OCA lids sealing region is minimized.
7.1.3      Inner Containment Vessel (ICV) Lid Removal
: 1. Remove the ICV vent port cover, the ICV outer vent port plug, and ICV inner vent port plug to vent the ICV cavity to ambient atmospheric pressure.
: 2. Remove the ICV seal test port plug.
: 3. Remove the three 1/2-inch lock bolts (socket head cap screws) from the exterior of the ICV locking ring.
: 4. Install a vacuum pump to the ICV vent port and evacuate the ICV cavity sufficiently to allow the ICV locking ring to freely rotate. Rotate the ICV locking ring approximately 10&#xba; counterclockwise until the exterior alignment mark indicates the unlocked position.
Disconnect the vacuum system and equalize pressure to the ICV cavity.
: 5. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the ICV lid. Engage the lift fixture and remove the ICV lid from the ICV body. Store the ICV lid in a manner such that potential damage to the ICV lids sealing region and ICV upper aluminum honeycomb spacer assembly is minimized.
7.1.4      Loading the Payload into the HalfPACT Package The following loading sequence requires that a payload configuration has been properly prepared per the requirements of the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) 1.
: 1. Verify the presence of an ICV upper aluminum honeycomb spacer assembly in the ICV lid, and an ICV lower aluminum honeycomb spacer assembly in the ICV body.
: 2. Utilizing the 3-inch diameter hole in the ICV lower aluminum honeycomb spacer assembly, inspect the ICV lower head for the presence of water. Remove all free-standing water prior to loading the payload assembly into the ICV cavity.
: 3. If the payload assembly is a 55-gallon drum configuration, short 85-gallon drum configuration, 100-gallon drum configuration, or a standard waste box (SWB), install a 1
U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
7.1-2
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 payload spacer into the bottom of the ICV cavity. If the payload assembly is an SC-30G1 shielded container configuration, install an axial dunnage into the bottom of the ICV cavity.
: 4. Connect an appropriate lifting device to the payload assembly.
: 5. Balance the payload assembly to ensure the payload does not damage either the ICV or the OCV sealing regions during the loading operation.
: 6. Lower the payload assembly into the ICV cavity; disconnect and remove the lifting device.
If the payload assembly is an SC-30G1 or SC-30G2 shielded container configuration, install an axial dunnage onto the top of the payload assembly.
7.1.5    Inner Containment Vessel (ICV) Lid Installation
: 1. Visually inspect each of the following ICV components for wear or damage that could impair their function and, if necessary, replace or repair per the requirements of the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
: a. ICV debris shield
: b. ICV wiper O-ring seal and wiper O-ring holder
: c. ICV seal test port plug and accompanying O-ring seal
: d. ICV inner vent port plug and accompanying O-ring seal
: e. ICV vent port cover and accompanying seal (O-ring or gasket)
: f. Lock bolts
: 2. Visually inspect both ICV main O-ring seals. If necessary, remove the O-ring seal(s) and clean the seal(s) and sealing surface(s) on the ICV lid and body to remove contamination. If, during the visual examination, it is determined that damage to the O-ring seal(s) and/or sealing surface(s) is sufficient to impair ICV containment integrity, replace the damaged seal(s) and/or repair the damaged sealing surface(s) per Section 8.2.3.3.1, Seal Area Routine Inspection and Repair.
: 3. Visually inspect the O-ring seal on the ICV outer vent port plug. If necessary, remove the O-ring seal and clean the seal and sealing surfaces on the ICV outer vent port plug and in the ICV vent port to remove contamination. If, during the visual examination, it is determined that damage to the O-ring seal and/or sealing surface(s) is sufficient to impair ICV containment integrity, replace the damaged seal and/or repair the damaged sealing surface(s) per Section 8.2.3.3.1, Seal Area Routine Inspection and Repair.
: 4. As an option, sparingly apply vacuum grease to the O-ring seals and install into the appropriate O-ring seal grooves in the ICV body, ICV seal test port and vent port plugs.
: 5. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the ICV lid. Engage the lift fixture and install the ICV lid onto the ICV body. Remove the lift fixture.
: 6. Install a vacuum pump to the ICV vent port and evacuate the ICV cavity sufficiently to allow the ICV locking ring to freely rotate. Rotate the ICV locking ring approximately 10&#xba; clockwise until the exterior alignment mark indicates the locked position. After rotating the ICV locking ring, disconnect the vacuum system and equalize pressure to the ICV cavity.
7.1-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 7. Install the three 1/2-inch lock bolts (socket head cap screws) through the cutouts in the ICV locking ring to secure the ICV locking ring in the locked position. Tighten the lock bolts to 28 - 32 lb-ft torque, lubricated.
: 8. Leakage rate testing of the ICV main O-ring seal shall be performed based on the following criteria:
: a. If the ICV upper main O-ring seal (containment) is replaced, or the corresponding sealing surface(s) was repaired, then perform the maintenance/periodic leakage rate test per Section 8.2.2.2, Helium Leakage Rate Testing the ICV Main O-ring Seal.
: b. If there are no changes to the ICV upper main O-ring seal (containment) and no repairs made to the corresponding sealing surfaces, then perform preshipment leakage rate testing per Section 7.4, Preshipment Leakage Rate Test, or per Section 8.2.2.2, Helium Leakage Rate Testing the ICV Main O-ring Seal.
: 9. Install the ICV seal test port plug; tighten to 55 - 65 lb-in torque.
: 10. Install the ICV outer vent port plug; tighten to 55 - 65 lb-in torque.
: 11. Leakage rate testing of the ICV outer vent port plug O-ring seal shall be performed based on the following criteria:
: a. If the ICV outer vent port plug O-ring seal is replaced, or the corresponding ICV vent port sealing surface was repaired, then perform the maintenance/periodic leakage rate test per Section 8.2.2.3, Helium Leakage Rate Testing the ICV Outer Vent Port Plug O-ring Seal.
: b. If the ICV outer vent port plug and accompanying O-ring seal are the same as previously removed, and no repairs made to the corresponding sealing surfaces, then perform preshipment leakage rate testing per Section 7.4, Preshipment Leakage Rate Test, or per Section 8.2.2.3, Helium Leakage Rate Testing the ICV Outer Vent Port Plug O-ring Seal.
: 12. Install the ICV vent port cover; tighten to 55 - 65 lb-in torque.
7.1.6      Outer Confinement Assembly (OCA) Lid Installation
: 1. Visually inspect each of the following OCA components for wear or damage that could impair their function and, if necessary, replace or repair per the requirements of the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
: a. OCV seal test port plug and, if used, the accompanying O-ring seal
: b. OCV vent port cover and, if used, the accompanying O-ring seal
: c. Lock bolts
: 2. If used, visually inspect both OCV main O-ring seals; otherwise, skip this step. If necessary, remove the O-ring seal(s) and clean the seal(s) and sealing surface(s) on the OCA lid and body to remove contamination. If, during the visual examination, it is determined that damage to the O-ring seal(s) and/or sealing surface(s) is sufficient to impair OCV confinement integrity, replace the damaged seal(s) and/or repair the damaged sealing surface(s) per Section 8.2.3.3.1, Seal Area Routine Inspection and Repair.
7.1-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 3. If used, visually inspect the O-ring seal on the OCV vent port plug; otherwise, skip this step.
If necessary, remove the O-ring seal and clean the seal and sealing surfaces on the OCV vent port plug and in the OCV vent port to remove contamination. If, during the visual examination, it is determined that damage to the O-ring seal and/or sealing surface(s) is sufficient to impair OCV confinement integrity, replace the damaged seal and/or repair the damaged sealing surface(s) per Section 8.2.3.3.1, Seal Area Routine Inspection and Repair.
: 4. As an option and if the O-ring seals are used, sparingly apply vacuum grease to the O-ring seals and install into the appropriate O-ring seal grooves in the OCV body, OCV seal test port plug, and OCV vent port plug.
: 5. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the OCA lid. Engage the lift fixture and install the OCA lid onto the OCA body. Remove the lift fixture.
: 6. Optionally install a vacuum pump to the OCV vent port and evacuate the OCV cavity sufficiently to allow the OCV locking ring to freely rotate. Rotate the OCV locking ring approximately 10&#xba; clockwise until the alignment mark indicates the locked position. After rotating the OCV locking ring, disconnect the vacuum system and equalize pressure to the OCV cavity.
: 7. Install the six 1/2-inch lock bolts (socket head cap screws) through the cutouts in the OCA outer thermal shield to secure the OCV locking ring in the locked position. Tighten the lock bolts to 28 - 32 lb-ft torque, lubricated.
: 8. Optionally perform leakage rate testing of the OCV main O-ring seal based on the following criteria:
: a. If the OCV upper main O-ring seal (confinement) is replaced, or the corresponding sealing surface(s) was repaired, then perform the maintenance/periodic leakage rate test per Section 8.1.3.6, Optional Helium Leakage Rate Testing the OCV Main O-ring Seal Integrity.
: b. If there are no changes to the OCV upper main O-ring seal (confinement) and no repairs made to the corresponding sealing surfaces, then perform preshipment leakage rate testing per Section 7.4, Preshipment Leakage Rate Test, or per Section 8.1.3.6, Optional Helium Leakage Rate Testing the OCV Main O-ring Seal Integrity.
: 9. Install the OCV seal test port plug; tighten to 55 - 65 lb-in torque. Install the OCV seal test port thermal plug and the OCV seal test port access plug; tighten to 28 - 32 lb-ft torque.
: 10. Install the OCV vent port plug; tighten to 55 - 65 lb-in torque.
: 11. Optionally perform leakage rate testing of the OCV vent port plug O-ring seal based on the following criteria:
: a. If the OCV vent port plug O-ring seal is replaced, or the corresponding OCV vent port sealing surface was repaired, then perform the maintenance/periodic leakage rate test per Section 8.1.3.7, Optional Helium Leakage Rate Testing the OCV Vent Port Plug O-ring Seal Integrity.
: b. If the OCV vent port plug and accompanying O-ring seal are the same as previously removed, and no repairs made to the corresponding sealing surfaces, then perform preshipment leakage rate testing per Section 7.4, Preshipment Leakage Rate Test, or per 7.1-5
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 Section 8.1.3.7, Optional Helium Leakage Rate Testing the OCV Vent Port Plug O-ring Seal Integrity.
: 12. Install the OCV vent port cover; tighten to 55 - 65 lb-in torque.
: 13. Install the OCV vent port thermal plug and the OCV vent port access plug; tighten to 28 - 32 lb-ft torque.
7.1.7        Final Package Preparations for Transport (Loaded)
: 1. Install the two tamper-indicating devices (security seals). One security seal is located at the OCA vent port access plug; the second is located at an OCA lock bolt.
: 2. If the HalfPACT package is not already loaded onto the transport trailer or railcar, perform the following steps:
: a. Using a forklift of appropriate size, position the forklifts forks inside the forklift pockets.
: b. Lift the loaded HalfPACT package, aligning the packaging over the tie-down points on the transport trailer or railcar.
: c. Secure the loaded HalfPACT package to the transport trailer or railcar using the appropriate tie-down devices.
: d. Load as many as three HalfPACT packages per transport trailer or up to seven HalfPACT packages per railcar.
: e. Install forklift pocket covers over the four forklift pockets located at the base of the OCA body.
: 3. Monitor external radiation for each loaded HalfPACT package per the guidelines of 49 CFR
    &sect;173.441 2.
: 4. Determine that surface contamination levels for each loaded HalfPACT package are per the guidelines of 49 CFR &sect;173.443.
: 5. Determine the shielding Transport Index (TI) for each loaded HalfPACT package per the guidelines of 49 CFR &sect;173.403.
: 6. Complete all necessary shipping papers in accordance with Subpart C of 49 CFR 172 3.
: 7. HalfPACT package marking shall be in accordance with 10 CFR &sect;71.85(c) 4 and Subpart D of 49 CFR 172. Package labeling shall be in accordance with Subpart E of 49 CFR 172.
Package placarding shall be in accordance with Subpart F of 49 CFR 172.
2 Title 49, Code of Federal Regulations, Part 173 (49 CFR 173), Shippers-General Requirements for Shipments and Packagings, Current Version.
3 Title 49, Code of Federal Regulations, Part 172 (49 CFR 172), Hazardous Materials Tables and Hazardous Communications Regulations, Current Version.
4 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
7.1-6
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 7.2 Procedures for Unloading the Package This section delineates the procedures for unloading a payload from the HalfPACT packaging.
Hereafter, reference to specific HalfPACT packaging components may be found in Appendix 1.3.1, Packaging General Arrangement Drawings.
The unloading operation shall be performed in a dry environment. In the event of precipitation during outdoor unloading operations, precautions, such as covering the outer confinement vessel (OCV) and inner containment vessel (ICV) cavities shall be implemented to prevent water or precipitation from entering the cavities. If precipitation enters the cavities, the free-standing water shall be removed prior to installing the lids.
* If the HalfPACT package will be unloaded while on the transport trailer or railcar, proceed directly to Section 7.2.2, Outer Confinement Assembly (OCA) Lid Removal.
7.2.1      Removal of the HalfPACT Package from the Transport Trailer/Railcar
: 1. Uncover the forklift pockets located at the base of the OCA body.
: 2. Disengage each of the four (4) tie-down devices on the transport trailer or railcar from the corresponding tie-down lugs on the package.
CAUTION: Failure to disengage the tie-down devices may cause damage to the packaging and/or transport trailer/railcar.
: 3. Using a forklift of appropriate size, position the forklifts forks inside the forklift pockets.
: 4. Lift the package from the transport trailer or railcar and move the package to the loading station.
: 5. Place the package in the loading station and remove the forklift.
7.2.2 Outer Confinement Assembly (OCA) Lid Removal
: 1. If necessary, clean the surfaces around the joint between the OCA lid and body as required.
: 2. Remove the OCV seal test port access plug, OCV seal test port thermal plug, and OCV seal test port plug.
: 3. Remove the OCV vent port access plug, OCV vent port thermal plug, and OCV vent port cover.
: 4. Remove the OCV vent port plug to vent the OCV cavity to ambient atmospheric pressure.
: 5. Remove the six 1/2-inch lock bolts (socket head cap screws) from the exterior of the OCA thermal shield.
: 6. Optionally install a vacuum pump to the OCV vent port and evacuate the OCV cavity sufficiently to allow the OCV locking ring to freely rotate. Rotate the OCV locking ring approximately 10&#xba; counterclockwise until the exterior alignment mark indicates the unlocked position. If used, disconnect the vacuum system and equalize pressure to the OCV cavity.
7.2-1
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 7. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the OCA lid. Engage the lift fixture and remove the OCA lid from the OCA body. Store the OCA lid in a manner such that potential damage to the OCA lids sealing region is minimized.
7.2.3    Inner Containment Vessel (ICV) Lid Removal
: 1. Remove the ICV vent port cover, the ICV outer vent port plug, and ICV inner vent port plug to vent the ICV cavity to ambient atmospheric pressure.
: 2. Remove the ICV seal test port plug.
: 3. Remove the three 1/2-inch lock bolts (socket head cap screws) from the exterior of the ICV locking ring.
: 4. Install a vacuum pump to the ICV vent port and evacuate the ICV cavity sufficiently to allow the ICV locking ring to freely rotate. Rotate the ICV locking ring approximately 10&#xba; counterclockwise until the alignment mark indicates the unlocked position. Disconnect the vacuum system and equalize pressure to the ICV cavity.
: 5. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the ICV lid. Engage the lift fixture and remove the ICV lid from the ICV body. Store the ICV lid in a manner such that potential damage to the ICV lids sealing region and ICV upper aluminum honeycomb spacer assembly is minimized.
7.2.4    Unloading the Payload from the HalfPACT Package
: 1. Connect an appropriate lifting device to the payload assembly. If the payload assembly is an SC-30G1 or SC-30G2 shielded container configuration, remove the axial dunnage from the top of the payload assembly first.
: 2. Balance the payload assembly sufficiently to ensure the payload does not damage either the ICV or the OCV sealing regions during the unloading operation.
: 3. Remove the payload assembly from the ICV cavity; disconnect and remove the lifting device.
7.2.5    Inner Containment Vessel (ICV) Lid Installation
: 1. Visually inspect each of the following ICV components for wear or damage that could impair their function and, if necessary, replace or repair per the requirements of the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
: a. ICV debris shield
: b. ICV wiper O-ring seal and wiper O-ring holder
: c. ICV main O-ring seals and sealing surfaces
: d. ICV seal test port plug and accompanying O-ring seal
: e. ICV inner and outer vent port plugs and accompanying O-ring seals
: f. ICV vent port cover and accompanying seal (O-ring or gasket)
: g. Lock bolts 7.2-2
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 2. As an option, sparingly apply vacuum grease to the O-ring seals and install into the appropriate O-ring seal grooves in the ICV body, ICV seal test port and vent port plugs.
: 3. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the ICV lid. Engage the lift fixture and install the ICV lid onto the ICV body. Remove the lift fixture.
: 4. Install a vacuum pump to the ICV vent port and evacuate the ICV cavity sufficiently to allow the ICV locking ring to freely rotate. Rotate the ICV locking ring approximately 10&#xba; clockwise until the alignment mark indicates the locked position. After rotating the ICV locking ring, disconnect the vacuum system and equalize pressure to the ICV cavity.
: 5. Install the three 1/2-inch lock bolts (socket head cap screws) through the cutouts in the ICV locking ring to secure the ICV locking ring in the locked position. Tighten the lock bolts to 28 - 32 lb-ft torque, lubricated.
: 6. Install the ICV seal test port plug; tighten to 55 - 65 lb-in torque.
: 7. Install the ICV inner and outer vent port plugs, followed by the ICV vent port cover; tighten each to 55 - 65 lb-in torque.
7.2.6      Outer Confinement Assembly (OCA) Lid Installation
: 1. Visually inspect each of the following OCA components for wear or damage that could impair their function and, if necessary, replace or repair per the requirements of the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
: a. OCV main O-ring seals, if used, and sealing surfaces
: b. OCV seal test port plug and, if used, the accompanying O-ring seal
: c. OCV vent port plug and, if used, the accompanying O-ring seal
: d. OCV vent port cover and, if used, the accompanying O-ring seal
: e. Lock bolts
: 2. As an option and if O-ring seals are used, sparingly apply vacuum grease to the O-ring seals and install into the appropriate O-ring seal grooves in the OCV body, OCV seal test port and vent port plugs.
: 3. Rig an overhead crane, or equivalent, with an appropriate lift fixture capable of handling the OCA lid. Engage the lift fixture and install the OCA lid onto the OCA body. Remove the lift fixture.
: 4. Optionally install a vacuum pump to the OCV vent port and evacuate the OCV cavity sufficiently to allow the OCV locking ring to freely rotate. Rotate the OCV locking ring approximately 10&#xba; clockwise until the alignment mark indicates the locked position. After rotating the OCV locking ring, disconnect the vacuum system and equalize pressure to the OCV cavity.
: 5. Install the six 1/2-inch lock bolts (socket head cap screws) through the cutouts in the OCA outer thermal shield to secure the OCV locking ring in the locked position. Tighten the lock bolts to 28 - 32 lb-ft torque, lubricated.
7.2-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 6. Install the OCV seal test port plug; tighten to 55 - 65 lb-in torque. Install the OCV seal test port thermal plug and the OCV seal test port access plug; tighten to 28 - 32 lb-ft torque.
: 7. Install the OCV vent port plug and OCV vent port cover; tighten each to 55 - 65 lb-in torque.
Install the OCV vent port thermal plug and the OCV vent port access plug; tighten to 28 - 32 lb-ft torque.
7.2.7 Final Package Preparations for Transport (Unloaded)
: 1. If the HalfPACT package is not already loaded onto the transport trailer or railcar, perform the following steps:
: a. Using a forklift of appropriate size, position the forklifts forks inside the forklift pockets.
: b. Lift the HalfPACT package, aligning the packaging over the tie-down points on the transport trailer or railcar.
: c. Secure the HalfPACT package to the transport trailer or railcar using the appropriate tie-down devices.
: d. Load as many as three HalfPACT packages per transport trailer or up to seven HalfPACT packages per railcar.
: e. Install forklift pocket covers over the four forklift pockets located at the base of the OCA body.
: 2. Transport the HalfPACT package in accordance with Section 7.3, Preparation of an Empty Package for Transport.
7.2-4
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 7.3 Preparation of an Empty Package for Transport Previously used and empty HalfPACT packagings shall be prepared and transported per the requirements of 49 CFR &sect;173.428 1.
1 Title 49, Code of Federal Regulations, Part 173 (49 CFR 173), Shippers-General Requirements for Shipments and Packagings, Current Version.
7.3-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
7.3-2
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 7.4 Preshipment Leakage Rate Test After the HalfPACT package is assembled and prior to shipment, leakage rate testing shall be performed to confirm proper assembly of the package following the guidelines of Section 7.6, Preshipment Leakage Rate Test, and Appendix A.5.2, Gas Pressure Rise, of ANSI N14.5 1.
7.4.1      Gas Pressure Rise Leakage Rate Test Acceptance Criteria In order to demonstrate containment integrity in preparation for shipment, no leakage shall be detected when tested to a sensitivity of 1 x 10-3 reference cubic centimeters per second (scc/s) air, or less, per Section 7.6, Preshipment Leakage Rate Test, of ANSI N14.5.
7.4.2      Determining the Test Volume and Test Time
: 1. Assemble a leakage rate test apparatus that consists of, at a minimum, the components illustrated in Figure 7.4-1, using a calibrated volume with a range of 100 - 500 cubic centimeters, and a calibrated pressure transducer with a minimum sensitivity of 100 millitorr. Connect the test apparatus to the test volume (i.e., the OCV or ICV seal test port, or OCV or ICV vent port, as appropriate).
: 2. Set the indicated sensitivity on the digital readout of the calibrated pressure transducer, P, to, at a minimum, the resolution (i.e., sensitivity) of the calibrated pressure transducer (e.g, P = 1, 10, or 100 millitorr for a pressure transducer with a 1 millitorr sensitivity).
: 3. Open all valves (i.e., the vent valve, calibration valve, and vacuum pump isolation valve),
and record ambient atmospheric pressure, Patm.
: 4. Isolate the calibrated volume by closing the vent and calibration valves.
: 5. Evacuate the test volume to a pressure less than the indicated sensitivity on the digital readout of the calibrated pressure transducer or 0.76 torr, whichever is less.
: 6. Isolate the vacuum pump from the test volume by closing the vacuum pump isolation valve.
Allow the test volume pressure to stabilize and record the test volume pressure, Ptest (e.g., Ptest < 1 millitorr for an indicated sensitivity of 1 millitorr).
: 7. Open the calibration valve and, after allowing the system to stabilize, record the total volume pressure, Ptotal.
: 8. Knowing the calibrated volume, Vc, calculate and record the test volume, Vt, using the following equation:
P  Ptotal Vt = Vc  atm Ptotal  Ptest
: 9. Knowing the indicated sensitivity on the digital readout of the calibrated pressure transducer, P, calculate and record the test time, t, using the following equation:
t = P(1.32)Vt 1
ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
7.4-1
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 7.4.3      Performing the Gas Pressure Rise Leakage Rate Test
: 1. Isolate the calibrated volume by closing the calibration valve.
: 2. Open the vacuum pump isolation valve and evacuate the test volume to a pressure less than the test volume pressure, Ptest, determined in step 6 of Section 7.4.2, Determining the Test Volume and Test Time.
: 3. Isolate the vacuum pump from the test volume by closing the vacuum pump isolation valve.
Allow the test volume pressure to stabilize and record the beginning test pressure, P1. After a period of time equal to t seconds, determined in step 9 of Section 7.4.2, Determining the Test Volume and Test Time, record the ending test pressure, P2. To be acceptable, there shall be no difference between the final and initial pressures such that the requirements of Section 7.4.1, Gas Pressure Rise Leakage Rate Test Acceptance Criteria, are met.
: 4. If, after repeated attempts, the O-ring seal fails to pass the leakage rate test, replace the damaged seal and/or repair the damaged sealing surfaces per Section 8.2.3.3.1, Seal Area Routine Inspection and Repair. Perform verification leakage rate test per the applicable procedure delineated in Section 8.2.2, Maintenance/Periodic Leakage Rate Tests.
7.4.4      Optional Preshipment Leakage Rate Test As an option to Section 7.4.3, Performing the Gas Pressure Rise Leakage Rate Test, Section 8.2.2, Maintenance/Periodic Leakage Rate Tests, may be performed.
To Test Volume Vent                                  Calibration Valve                                    Valve Vc                                                          999.9 Pressure            Digital Calibrated        Vacuum Pump              Transducer          Readout Volume          Isolation Valve Vacuum Pump Figure 7.4 Pressure Rise Leakage Rate Test Schematic 7.4-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 8.0 ACCEPTANCE TESTS AND MAINTENANCE PROGRAM 8.1 Acceptance Tests Per the requirements of 10 CFR &sect;71.85 1, this section discusses the inspections and tests to be performed prior to first use of the HalfPACT packaging.
8.1.1        Visual Inspection All HalfPACT packaging materials of construction and welds shall be examined in accordance with requirements delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings, per the requirements of 10 CFR &sect;71.85(a). Furthermore, the inspections and tests of Section 8.2.3.3, Seal Areas and Grooves, shall be performed prior to pressure and leakage rate testing.
8.1.2        Structural and Pressure Tests 8.1.2.1      Lifting Device Load Testing The bounding design load of the outer confinement assembly (OCA) lid lifting devices is 7,500 pounds total, or 2,500 pounds per lifting point. Load test each set of OCA lid lifting devices to 150% of their bounding design load, 11,250 pounds total, or 3,750 pounds per lifting point.
Perform load testing of the OCA lid lifting devices prior to polyurethane foam installation.
Following OCA load testing, all accessible base material and welds and adjacent base metal (minimum 1/2 inch on each side of the weld) directly related to OCA load testing shall be visually inspected for plastic deformation or cracking, and liquid penetrant inspected per ASME Boiler and Pressure Vessel Code, Section V 2, Article 6, and ASME Boiler and Pressure Vessel Code, Section III 3, Division 1, Subsection NF, Article NF-5000. Indications of cracking or distortion shall be recorded on a nonconformance report and dispositioned prior to final acceptance in accordance with the cognizant quality assurance program.
The bounding design load of the inner containment vessel (ICV) lifting sockets is 5,000 pounds total, or 1,667 pounds per lifting socket. Load test each set of ICV lifting sockets to 150% of their bounding design load, 7,500 pounds total, or 2,500 pounds per lifting socket.
Following ICV load testing, all accessible base material and welds and adjacent base metal (minimum 1/2 inch on each side of the weld) directly related to ICV load testing shall be visually inspected for plastic deformation or cracking, and liquid penetrant inspected per ASME Boiler and Pressure Vessel Code, Section V2, Article 6, and ASME Boiler and Pressure Vessel Code, Section III3, Division 1, Subsection NB, Article NB-5000. Indications of cracking or distortion 1
Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section V, Nondestructive Examination, 1995 Edition, 1997 Addenda.
3 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, 1995 Edition, 1997 Addenda.
8.1-1
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 shall be recorded on a nonconformance report and dispositioned prior to final acceptance in accordance with the cognizant quality assurance program.
8.1.2.2    Pressure Testing Per the requirements of 10 CFR &sect;71.85(b), the ICV shall be pressure tested to 150% of the maximum normal operating pressure (MNOP) to verify structural integrity. The MNOP of the ICV is equal to the 50 psig design pressure. Thus, the ICV shall be pressure tested to 50 x 1.5 =
75 psig.
Following ICV pressure testing, all accessible welds and adjacent base metal (minimum 1/2 inch on each side of the weld) directly related to the pressure testing of the ICV shall be visually inspected for plastic deformation or cracking, and liquid penetrant inspected per ASME Boiler and Pressure Vessel Code, Section V, Article 6, and ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-5000, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. Indications of cracking or distortion shall be recorded on a nonconformance report and dispositioned prior to final acceptance in accordance with the cognizant quality assurance program.
The outer confinement vessel (OCV) may optionally be pressure tested to 150% of the maximum normal operating pressure (MNOP) to verify structural integrity. The MNOP of the OCV is equal to the 50 psig design pressure. Thus, the OCV may optionally be pressure tested to 50 x 1.5 = 75 psig.
Following optional OCV pressure testing, all accessible welds and adjacent base metal (minimum 1/2 inch on each side of the weld) directly related to the pressure testing of the OCV shall be visually inspected for plastic deformation or cracking, and liquid penetrant inspected per ASME Boiler and Pressure Vessel Code, Section V, Article 6, and ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NF, Article NF-5000, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. Indications of cracking or distortion shall be recorded on a nonconformance report and dispositioned prior to final acceptance in accordance with the cognizant quality assurance program.
Leakage rate testing per Section 8.1.3, Fabrication Leakage Rate Tests, shall be performed on the ICV and may optionally be performed on the OCV after completion of pressure testing to verify package configuration and performance to design criteria.
8.1.3      Fabrication Leakage Rate Tests This section provides the generalized procedure for fabrication leakage rate testing of the containment and, optionally, confinement vessel boundaries and penetrations following the completion of fabrication. Fabrication leakage rate testing shall follow the guidelines of Section 7.3, Fabrication Leakage Rate Test, of ANSI N14.5 4.
Prior to leakage rate testing, internal components such as the payload and spacer pallets, ICV aluminum honeycomb spacer assemblies, etc., shall be removed. For ease of leakage rate testing, each vessel should be thoroughly cleaned.
4 ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
8.1-2
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022 Fabrication leakage rate testing shall be performed on the ICV and may optionally be performed on the OCV. Six separate tests comprise the series with three on the ICV and three on the OCV.
Each test shall meet the acceptance criteria delineated in Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria.
8.1.3.1      Fabrication Leakage Rate Test Acceptance Criteria
: 1. To be acceptable, each leakage rate test shall demonstrate a leaktight leakage rate of 1 x 10-7 reference cubic centimeters per second (scc/s), air, or less, per Section 6.3, Application of Referenced Air Leakage Rate (LR), of ANSI N14.5.
: 2. In order to demonstrate a leaktight leakage rate, the sensitivity of the leakage rate test procedure shall be 5 x 10-8 scc/s, air, or less, per Section 8.4, Sensitivity, of ANSI N14.5.
8.1.3.2      Helium Leakage Rate Testing the ICV Structure Integrity
: 1. The fabrication leakage rate test of the ICV structure shall be performed following the guidelines of Section A.5.4, Evacuated Envelope - Gas Detector, of ANSI N14.5.
: 2. The ICV shall be assembled with both main O-ring seals installed into the ICV lower seal flange. Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 3. Install the assembled ICV into a functional OCV body.
: 4. Remove the ICV vent port cover, ICV outer vent port plug, and ICV inner vent port plug.
: 5. Connect a vacuum pump to the ICV vent port and evacuate the ICV cavity to 90% vacuum or better (i.e., 10% ambient atmospheric pressure).
: 6. Provide a helium atmosphere inside the ICV cavity by backfilling with helium gas to a pressure slightly greater than atmospheric pressure (+1 psi, -0 psi).
: 7. Install the ICV outer vent port plug, followed by the ICV vent port cover; tighten each to 55 - 65 lb-in torque.
: 8. Ensure the OCV vent port access plug, OCV vent port thermal plug, OCV vent port cover, and OCV vent port plug have been removed from the OCV body.
: 9. With both main O-ring seals installed into the OCV lower seal flange, install the OCV lid.
Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 10. Install a helium mass spectrometer leak detector to the OCV vent port. Evacuate through the OCV vent port until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 11. Perform the helium leakage rate test to the requirements of Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the ICV structure fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.1.3.3      Helium Leakage Rate Testing the ICV Main O-ring Seal
: 1. The fabrication leakage rate test of the ICV main O-ring seal shall be performed following the guidelines of Section A.5.4, Evacuated Envelope - Gas Detector, of ANSI N14.5.
8.1-3
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022
: 2. The ICV shall be assembled with both main O-ring seals installed into the ICV lower seal flange. Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 3. Remove the ICV vent port cover, outer vent port plug, and inner vent port plug.
: 4. Connect a vacuum pump to the ICV vent port and evacuate the ICV cavity to 90% vacuum or better (i.e., 10% ambient atmospheric pressure).
: 5. Remove the ICV seal test port plug and install a helium mass spectrometer leak detector to the ICV seal test port. Evacuate through the ICV seal test port until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 6. Provide a helium atmosphere inside the ICV cavity by backfilling with helium gas to a pressure slightly greater than atmospheric pressure (+1 psi, -0 psi).
: 7. Perform the helium leakage rate test to the requirements of Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the ICV main O-ring seal fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.1.3.4    Helium Leakage Rate Testing the ICV Outer Vent Port Plug O-ring Seal
: 1. The fabrication leakage rate test of the ICV outer vent port plug O-ring seal shall be performed following the guidelines of Section A.5.4, Evacuated Envelope - Gas Detector, of ANSI N14.5.
: 2. The ICV shall be assembled with both main O-ring seals installed into the ICV lower seal flange. Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 3. Remove the ICV vent port cover, ICV outer vent port plug, and the ICV inner vent port plug.
: 4. Connect a vacuum pump to the ICV vent port and evacuate the ICV cavity to 90% vacuum or better (i.e., 10% ambient atmospheric pressure).
: 5. Provide a helium atmosphere inside the ICV cavity by backfilling with helium gas to a pressure slightly greater than atmospheric pressure (+1 psi, -0 psi).
: 6. Install the ICV outer vent port plug; tighten to 55 - 65 lb-in torque.
: 7. Install a helium mass spectrometer leak detector to the ICV vent port. Evacuate through the ICV vent port until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 8. Perform the helium leakage rate test to the requirements of Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the ICV outer vent port plug O-ring seal fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.1.3.5    Optional Helium Leakage Rate Testing the OCV Structure Integrity
: 1. The fabrication leakage rate test of the OCV structure shall be performed following the guidelines of Section A.5.3, Gas Filled Envelope - Gas Detector, of ANSI N14.5.
8.1-4
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022
: 2. Remove the OCV vent port access plug, OCV vent port thermal plug, OCV vent port cover, and OCV vent port plug.
: 3. Install the OCV lid with both main O-ring seals installed into the OCV lower seal flange. As an option, an assembled ICV may be placed within the OCV cavity for volume reduction.
Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 4. Install a helium mass spectrometer leak detector to the OCV vent port. Evacuate through the OCV vent port until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 5. Surround the assembled OCV with an envelope filled with helium.
: 6. Perform the helium leakage rate test to the requirements of Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the OCV structure fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.1.3.6    Optional Helium Leakage Rate Testing the OCV Main O-ring Seal Integrity
: 1. The fabrication leakage rate test of the OCV main O-ring seal shall be performed following the guidelines of Section A.5.4, Evacuated Envelope - Gas Detector, of ANSI N14.5.
: 2. The OCA shall be assembled with both main O-ring seals installed into the OCV lower seal flange. Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 3. Remove the OCV vent port access plug, OCV vent port thermal plug, OCV vent port cover, and OCV vent port plug.
: 4. Connect a vacuum pump to the OCV vent port and evacuate the OCV cavity to 90% vacuum or better (i.e., 10% ambient atmospheric pressure).
: 5. Remove the OCV seal test port access plug, OCV seal test port thermal plug, and OCV seal test port plug and install a helium mass spectrometer leak detector to the OCV seal test port.
Evacuate through the OCV seal test port until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 6. Provide a helium atmosphere inside the OCV cavity by backfilling with helium gas to a pressure slightly greater than atmospheric pressure (+1 psi, -0 psi).
: 7. Perform the helium leakage rate test to the requirements of Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the OCV main O-ring seal fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.1-5
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 8.1.3.7      Optional Helium Leakage Rate Testing the OCV Vent Port Plug O-ring Seal Integrity
: 1. The fabrication leakage rate test of the OCV vent port plug O-ring seal shall be performed following the guidelines of Section A.5.4, Evacuated Envelope - Gas Detector, of ANSI N14.5.
: 2. The OCV shall be assembled with both main O-ring seals installed into the OCV lower seal flange. Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 3. Remove the OCV vent port access plug, OCV vent port thermal plug, OCV vent port cover, and OCV vent port plug.
: 4. Connect a vacuum pump to the OCV vent port and evacuate the OCV cavity to 90% vacuum or better (i.e., 10% ambient atmospheric pressure).
: 5. Provide a helium atmosphere inside the OCV cavity by backfilling with helium gas to a pressure slightly greater than atmospheric pressure (+1 psi, -0 psi).
: 6. Install the OCV vent port plug; tighten to 55 - 65 lb-in torque.
: 7. Install a helium mass spectrometer leak detector to the OCV vent port. Evacuate through the OCV vent port until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 8. Perform the helium leakage rate test to the requirements of Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the OCV vent port plug O-ring seal fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.1.4      Component Tests 8.1.4.1      Polyurethane Foam This section establishes the requirements and acceptance criteria for installation, inspection, and testing of rigid, closed-cell, polyurethane foam utilized within the HalfPACT packaging.
8.1.4.1.1      Introduction and General Requirements The polyurethane foam used within the HalfPACT packaging is comprised of a specific formulation of foam constituents that, when properly apportioned, mixed, and reacted, produce a polyurethane foam material with physical characteristics consistent with the requirements given in this section. In practice, the chemical constituents are batched into multiple parts (e.g.,
parts A and B) for later mixing in accordance with a formulation. Therefore, a foam batch is considered to be a specific grouping and apportionment of chemical constituents into separate and controlled vats or bins for each foam formulation part. Portions from each batch part are combined in accordance with the foam formulation requirements to produce the liquid foam material for pouring into a component. Thus, a foam pour is defined as apportioning and mixing the batch parts into a desired quantity for subsequent installation (pouring).
8.1-6
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 The following sections describe the general requirements for chemical composition, constituent storage, foamed component preparation, foam material installation, and foam pour and test data records.
8.1.4.1.1.1      Polyurethane Foam Chemical Composition The foam supplier shall certify that the chemical composition of the polyurethane foam is as delineated below, with the chemical component weight percents falling within the specified ranges. In addition, the foam supplier shall certify that the finished (cured) polyurethane foam does not contain halogen-type flame retardants or trichloromonofluoromethane (Freon 11).
Carbon ....................... 50% - 70%            Phosphorus .................... 0% - 2%
Oxygen ...................... 14% - 34%            Silicon ................................. < 1%
Nitrogen ...................... 4% - 12%            Chlorine............................... < 1%
Hydrogen..................... 4% - 10%              Other ................................... < 1%
8.1.4.1.1.2      Polyurethane Foam Constituent Storage The foam supplier shall certify that the polyurethane foam constituents have been properly stored prior to use, and that the polyurethane foam constituents have been used within their shelf life.
8.1.4.1.1.3      Foamed Component Preparation Prior to polyurethane foam installation, the foam supplier shall visually verify to the extent possible (i.e., looking through the foam fill ports) that the ceramic fiber insulation is still attached to the component shell interior surfaces. In addition, due to the internal pressures generated during the foam pouring/curing process, the foam supplier shall visually verify that adequate bracing/shoring of the component shells is provided to maintain the dimensional configuration throughout the foam pouring/curing process.
8.1.4.1.1.4      Polyurethane Foam Installation As illustrated in the accompanying illustration, the direction of foam rise shall be vertically aligned with the shell component axis.
The surrounding walls of the component shell where the liquid foam material is to be installed shall be between 55 &#xba;F and 95 &#xba;F prior to foam installation. Measure and record the component shell temperature to an accuracy of +/-2 &#xba;F prior to foam installation.
In the case of multiple pours into a single foamed component, the cured level of each pour 8.1-7
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 shall be measured and recorded to an accuracy of +/-1 inch.
Measure and record the weight of liquid foam material installed during each pour to an accuracy of +/-10 pounds.
All test samples shall be poured into disposable containers at the same time as the actual pour it represents, clearly marking the test sample container with the pour date and a unique pour identification number. All test samples shall be cut from a larger block to obtain freshly cut faces. Prior to physical testing, each test sample shall be cleaned of superfluous foam dust.
8.1.4.1.1.5    Polyurethane Foam Pour and Test Data Records A production pour and testing record shall be compiled by the foam supplier during the foam pouring operation and subsequent physical testing. Upon completion of production and testing, the foam supplier shall issue certification referencing the production record data and test data pertaining to each foamed component. At a minimum, relevant pour and test data shall include:
* formulation, batch, and pour numbers, with foam material traceability, and pour date,
* foamed component description, part number, and serial number,
* instrumentation description, serial number, and calibration due date,
* pour and test data (e.g., date, temperature, dimensional, and/or weight measurements, compressive modulus, thermal conductivity, compressive stress, etc., as applicable), and
* technician and Quality Assurance/Quality Control (QA/QC) sign-off.
8.1.4.1.2    Physical Characteristics The following subsections define the required physical characteristics of the polyurethane foam material used for the HalfPACT packaging design.
Testing for the various polyurethane foam physical characteristics is based on a formulation, batch, or pour, as appropriate, as defined in Section 8.1.4.1.1, Introduction and General Requirements. The physical characteristics determined for a specific foam formulation are relatively insensitive to small variations in chemical constituents and/or environmental conditions, and therefore include physical testing for compressive modulus, Poissons ratio, thermal expansion coefficient, thermal conductivity, and specific heat. Similarly, the physical characteristics determined for a batch are only slightly sensitive to small changes in formulation and/or environmental conditions during batch mixing, and therefore include physical testing for flame retardancy, intumescence, and leachable chlorides. Finally, the physical characteristics determined for a pour are also only slightly sensitive to small changes in formulation and slightly more sensitive to variations in environmental conditions during pour mixing, and therefore include physical testing for density and compressive stress.
8.1.4.1.2.1    Physical Characteristics Determined for a Foam Formulation Foam material physical characteristics for the following parameters shall be determined once for a particular foam formulation. If multiple components are to be foamed utilizing a specific foam formulation, then additional physical testing, as defined below, need not be performed.
8.1-8
 
HalfPACT Safety Analysis Report                                                                                      Rev. 9, August 2022 8.1.4.1.2.1.1    Parallel-to-Rise Compressive Modulus
: 1. Three (3) test samples shall be taken from the sample pour. Each test sample shall be a rectangular prism with nominal dimensions of 1.0 inch thick (T) x 2.0 inches wide (W) x 2.0 inches long (L). The thickness dimension shall be in the parallel-to-rise direction.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 3. Measure and record the thickness, width, and length of each test sample to an accuracy of +/-0.001 inches.
: 4. Compute and record the surface area of each test sample by multiplying the width by the length (i.e., W x L).
: 5. Place a test sample in a Universal Testing Machine. Lower the machines crosshead until it touches the test sample. Set the machines parameters for the thickness of the test sample.
: 6. Apply a compressive load to each test sample at a rate of 0.10 +/-0.05 inches/minute until the compressive stress somewhat exceeds the elastic range of the foam material (i.e., the elastic range is typically        Linear Region Yield Region 0% - 6% strain). Plot the compressive stress versus          300 strain for each test sample.
: 7. Determine and record the parallel-to-rise compressive                              250 modulus, E, of each test sample by computing the slope in the linear region of the elastic range of the stress-strain curve, where i and j, and i and j are the strain                        200 and compressive stress at two selected points i and j, Compressive Stress (psi) j respectively, in the linear region of the stress-strain 150 curve (see example curve to right) as follows:
j  i E=              , psi                                          100                            j  i j  i
: 8. Determine and record the average parallel-to-rise                                        50 i
compressive modulus of the three test samples. The                                                      j  i numerically averaged, parallel-to-rise compressive modulus of the three test samples shall be 6,810 psi                                    0 0
i        j      5      Strain (%)  10  15
  +/-20% (i.e., within the range of 5,448 to 8,172 psi).
8.1-9
 
HalfPACT Safety Analysis Report                                                                                      Rev. 9, August 2022 8.1.4.1.2.1.2    Perpendicular-to-Rise Compressive Modulus
: 1. Three (3) test samples shall be taken from the sample pour. Each test sample shall be a rectangular prism with nominal dimensions of 1.0 inch thick (T) x 2.0 inches wide (W) x 2.0 inches long (L). The thickness dimension shall be in the perpendicular-to-rise direction.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 3. Measure and record the thickness, width, and length of each test sample to an accuracy of +/-0.001 inches.
: 4. Compute and record the surface area of each test sample by multiplying the width by the length (i.e., W x L).
: 5. Place a test sample in a Universal Testing Machine. Lower the machines crosshead until it touches the test sample. Set the machines parameters for the thickness of the test sample.
: 6. Apply a compressive load to each test sample at a rate of 0.10 +/-0.05 inches/minute until the compressive stress somewhat exceeds the elastic range of the foam material (i.e., the elastic range is typically 0% - 6% strain). Plot the compressive stress versus strain for each test sample.                        Linear Yield Region            Region
: 7. Determine and record the perpendicular-to-rise                                      300 compressive modulus, E, of each test sample by computing the slope in the linear region of the elastic range of the stress-strain curve, where i and j, and i                          250 and j are the strain and compressive stress at two selected points i and j, respectively, in the linear region                        200 of the stress-strain curve (see example curve to right) as Compressive Stress (psi) follows:                                                                                j j  i                                                  150 E=              , psi j  i j  i
: 8. Determine and record the average perpendicular-to-rise 100 compressive modulus of the three test samples. The numerically averaged, perpendicular-to-rise compressive                                  50 modulus of the three test samples shall be 4,773 psi                                    i j  i
  +/-20% (i.e., within the range of 3,818 to 5,728 psi).
0 0
i        j      5                  10  15 Strain (%)
8.1-10
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 8.1.4.1.2.1.3    Poissons Ratio
: 1. Three (3) test samples shall be taken from the sample pour.
Each test sample shall be a rectangular prism with nominal dimensions of 2.0 inches thick (T) x 2.0 inches wide (W) x 2.0 inches long (L). The thickness dimension shall be in the parallel-to-rise direction.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 3. Measure and record the thickness, width, and length of each test sample to an accuracy of +/-0.001 inches.
: 4. Place a test sample in a Universal Testing Machine. Lower the machines crosshead until it touches the test sample. Set the machines parameters for the thickness of the test sample.
: 5. As illustrated below, place two orthogonally oriented dial indicators at the mid-plane of one width face and one length face of the test sample to record the lateral deflections. The dial indicators shall be capable of measuring to an accuracy of +/-0.001 inches.
: 6. Apply a compressive load to each test sample so that the strain remains within the elastic range of the material, as determined in Section 8.1.4.1.2.1.1, Parallel-to-Rise Compressive Modulus. Record the axial crosshead displacement (T) and both dial indicator displacements (W and L) at one strain point within the elastic range for each test sample.
: 7. Determine and record Poissons ratio of each test sample as follows:
W W + L L
                                        &#xb5;=
T T 8.1-11
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022
: 8. Determine and record the average Poissons ratio of the three test samples. The numerically averaged Poissons ratio of the three test samples shall be 0.33 +/-20% (i.e., within the range of 0.26 to 0.40).
8.1.4.1.2.1.4    Thermal Expansion Coefficient
: 1. Three (3) test samples shall be taken from the sample pour. Each test sample shall be a rectangular prism with a nominal cross-section of 1.0 inch square and a nominal length of 6.0 inches.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature (TRT) to an accuracy of +/-2 &#xba;F.
: 3. Measure and record the room temperature length (LRT) of each test sample to an accuracy of
    +/-0.001 inches.
: 4. Place the test samples in a -40 &#xba;F to -60 &#xba;F cold environment for a minimum of three hours.
Measure and record the cold environment temperature (TC) to an accuracy of +/-2 &#xba;F.
: 5. Measure and record the cold environment length (LC) of each test sample to an accuracy of
    +/-0.001 inches.
: 6. Determine and record the cold environment thermal expansion coefficient for each test sample as follows:
C =
(LC  L RT ) , in/in/ o F (L RT )(TC  TRT )
: 7. Place the test samples in a 180 &#xba;F to 200 &#xba;F hot environment for a minimum of three hours.
Measure and record the hot environment temperature (TH) to an accuracy of +/-2 &#xba;F.
: 8. Measure and record the hot environment length (LH) of each test sample to an accuracy of
    +/-0.001 inches.
: 9. Determine and record the hot environment thermal expansion coefficient for each test sample as follows:
H =
(L H  L RT ) , in/in/ o F (L RT )(TH  TRT )
: 10. Determine and record the average thermal expansion coefficient of each test sample as follows:
C +  H
                                        =            , in/in/ o F 2
: 11. Determine and record the average thermal expansion coefficient of the three test samples. The numerically averaged thermal expansion coefficient of the three test samples shall be 3.5 x 10-5 in/in/&#xba;F +/-20% (i.e., within the range of 2.8 x 10-5 to 4.2 x 10-5 in/in/&#xba;F).
8.1.4.1.2.1.5    Thermal Conductivity
: 1. The thermal conductivity test shall be performed using a heat flux meter (HFM) apparatus.
The HFM establishes steady state unidirectional heat flux through a test specimen between 8.1-12
 
HalfPACT Safety Analysis Report                                                    Rev. 9, August 2022 two parallel plates at constant but different temperatures. By measurement of the plate temperatures and plate separation, Fouriers law of heat conduction is used by the HFM to automatically calculate thermal conductivity. Description of a typical HFM is provided in ASTM C518 5. The HFM shall be calibrated against a traceable reference specimen per the HFM manufacturer's operating instructions.
: 2. Three (3) test samples shall be taken from the sample pour. Each test sample shall be of sufficient size to enable testing per the HFM manufacturer's operating instructions.
: 3. Measure and record the necessary test sample parameters as input data to the HFM per the HFM manufacturer's operating instructions.
: 4. Perform thermal conductivity testing and record the measured thermal conductivity for each test sample following the HFM manufacturer's operating instructions.
: 5. Determine and record the average thermal conductivity of the three test samples. The numerically averaged thermal conductivity of the three test samples shall be 0.230 Btu-in/hr-ft2-&#xba;F +/-20% (i.e., within the range of 0.184 to 0.276 Btu-in/hr-ft2-&#xba;F).
8.1.4.1.2.1.6    Specific Heat
: 1. The specific heat test shall be performed using a differential scanning calorimeter (DSC) apparatus. The DSC establishes a constant heating rate and measures the differential heat flow into both a test specimen and a reference specimen. Description of a typical DSC is provided in ASTM E1269 6. The DSC shall be calibrated against a traceable reference specimen per the DSC manufacturer's operating instructions.
: 2. Three (3) test samples shall be taken from the sample pour. Each test sample shall be of sufficient size to enable testing per the DSC manufacturer's operating instructions.
: 3. Measure and record the necessary test sample parameters as input data to the DSC per the DSC manufacturer's operating instructions.
: 4. Perform specific heat testing and record the measured specific heat for each test sample following the DSC manufacturer's operating instructions.
: 5. Determine and record the average specific heat of the three test specimens. The numerically averaged specific heat at 77 &#xba;F of the three test samples shall be 0.30 Btu/lb-&#xba;F +/-20% (i.e.,
within the range of 0.24 to 0.36 Btu/lb-&#xba;F).
8.1.4.1.2.2      Physical Characteristics Determined for a Foam Batch Foam material physical characteristics for the following parameters shall be determined once for a particular foam batch based on the batch definition from Section 8.1.4.1.1, Introduction and General Requirements. If a single or multiple components are to be poured utilizing multiple pours from a single foam batch, then additional physical testing, as defined below, need not be performed for each foam pour.
5 ASTM C518, Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Heat Flux Meter Apparatus, American Society of Testing and Materials (ASTM).
6 ASTM E1269, Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry, American Society of Testing and Materials (ASTM).
8.1-13
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022 8.1.4.1.2.2.1    Flame Retardancy
: 1. Three (3) test samples shall be taken from a pour from each foam batch. Each test sample shall be a rectangular prism with nominal dimensions of 0.5 inches thick, 3.0 inches wide, and a minimum length of 6.0 inches. In addition, individual sample lengths must not be less than the total burn length observed for the sample when tested.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85
  &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 3. Measure and record the length of each test sample to an accuracy of +/-0.1 inches.
: 4. Install a &#xd8;3/8 inches (10 mm), or larger, Bunsen or Tirrill burner inside an enclosure of sufficient size to perform flame retardancy testing. Adjust the burner flame height to 11/2 +/-1/8 inches. Verify that the burner flame temperature is 1,550 &#xba;F, minimum.
: 5. Support the test sample with the long axis oriented vertically within the enclosure such that the test samples bottom edge will be 3/4 +/-1/16 inches above the top edge of the burner.
: 6. Move the burner flame under the test sample for an elapsed time of 60 +/-2 seconds. As illustrated, align the burner flame with the front edge of the test sample thickness and the center of the test sample width.
: 7. Immediately after removal of the test sample from the burner flame, measure and record the following data:
: a. Measure and record, to the nearest second, the elapsed time until flames from the test sample extinguish.
: b. Measure and record, to the nearest second, the elapsed time from the occurrence of drips, if any, until drips from the test sample extinguish.
: c. Measure and record, to the nearest 0.1 inches, the burn length following cessation of all visible burning and smoking.
: 8. Flame retardancy testing acceptance is based on the following criteria:
: a. The numerically averaged flame extinguishment time of the three test samples shall not exceed fifteen (15) seconds.
: b. The numerically averaged flame extinguishment time of drips from the three test samples shall not exceed three (3) seconds.
: c. The numerically averaged burn length of the three test samples shall not exceed six (6) inches.
8.1-14
 
HalfPACT Safety Analysis Report                                                  Rev. 9, August 2022 8.1.4.1.2.2.2      Intumescence
: 1. Three (3) test samples shall be taken from a pour from each foam batch. Each test sample shall be a cube with nominal dimensions of 2.0 inches.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 3. Preheat a furnace to 1,475 &#xba;F +/-18 &#xba;F.
: 4. Identify two opposite faces on each test sample as the thickness direction. The thickness dimension shall be in the parallel-to-rise direction. Measure and record the initial thickness (ti) of each test sample to an accuracy of +/-0.01 inches.
: 5. Mount a test sample onto a fire resistant fiberboard, with one face of the thickness direction contacting to the board. As illustrated above, the test samples may be mounted by installing onto a 12 to 16 gauge wire (&#xd8;0.105 to &#xd8;0.063 inches, respectively) of sufficient length, oriented perpendicular to the fiberboard face. The test samples may be pre-drilled with an undersized hole to allow installation onto the wire.
: 6. Locate the test sample/fiberboard assembly over the opening of the pre-heated furnace for a 90 +/-3 second duration. After removal of the test sample/fiberboard assembly from the furnace, gently extinguish any remaining flames and allow the test sample to cool.
: 7. Measure and record the final thickness (tf) of the test sample to an accuracy of +/-0.1 inches.
: 8. For each sample tested, determine and record the intumescence, I, as a percentage of the original sample length as follows:
t t I =  f i  x 100 ti
: 9. Determine and record the average intumescence of the three test samples. The numerically averaged intumescence of the three test samples shall be a minimum of 50%.
8.1.4.1.2.2.3      Leachable Chlorides
: 1. The leachable chlorides test shall be performed using an ion chromatograph (IC) apparatus.
The IC measures inorganic anions of interest (i.e., chlorides) in water. Description of a typical IC is provided in EPA Method 300.0 7. The IC shall be calibrated against a traceable reference specimen per the IC manufacturer's operating instructions.
: 2. One (1) test sample shall be taken from the sample pour. The test sample shall be a cube with dimensions of 2.00 +/-0.03 inches.
7 EPA Method 300.0, Determination of Inorganic Anions in Water by Ion Chromatography, U.S. Environmental Protection Agency.
8.1-15
 
HalfPACT Safety Analysis Report                                            Rev. 9, August 2022
: 3. Place the test sample in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test sample. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 4. Measure and record the thickness, width, and length of each test sample to an accuracy of
  +/-0.001 inches.
: 5. Obtain a minimum of 550 ml of distilled or de-ionized water for testing. The test water shall be from a single source to ensure consistent anionic properties for testing control.
: 6. Obtain a 400 ml, or larger, contaminant free container that is capable of being sealed. Fill the container with 262 +/-3 ml of test water. Fully immerse the test sample inside the container for a duration of 72 +/-3 hours. If necessary, use an inert standoff to ensure the test sample is completely immersed for the full test duration. Seal the container prior to the 72 hour duration.
: 7. Obtain a second, identical container to use as a control. Fill the control container with 262 +/-3 ml of the same test water. Seal the control container for a 72 +/-3 hour duration.
: 8. At the end of the test period, measure and record the leachable chlorides in the test water per the IC manufacturer's operating instructions. The leachable chlorides in the test water shall not exceed one part per million (1 ppm).
: 9. Should leachable chlorides in the test water exceed 1 ppm, measure and record the leachable chlorides in the test water from the control container. The difference in leachable chlorides from the test water and control water sample shall not exceed 1 ppm.
8.1.4.1.2.3    Physical Characteristics Determined for a Foam Pour Foam material physical characteristics for the following parameters shall be determined for each foam pour based on the pour definition from Section 8.1.4.1.1, Introduction and General Requirements.
8.1.4.1.2.3.1 Density
: 1. Three (3) test samples shall be taken from the foam pour. Each test sample shall be a rectangular prism with nominal dimensions of 1.0 inch thick (T) x 2.0 inches wide (W) x 2.0 inches long (L).
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 3. Measure and record the weight of each test sample to an accuracy of +/-0.01 grams.
: 4. Measure and record the thickness, width, and length of each test sample to an accuracy of
  +/-0.001 inches.
: 5. Determine and record the room temperature density of each test sample utilizing the following formula:
Weight, g 1,728 in 3 /ft 3 foam =            x              , pcf 453.6 g/lb T x W x L in 3 8.1-16
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 6. Determine and record the average density of the three test samples. The numerically averaged density of the three test samples shall be 81/4 pcf +/-15% (i.e., within the range of 7 to 91/2 pcf).
8.1.4.1.2.3.2    Parallel-to-Rise Compressive Stress
: 1. Three (3) test samples shall be taken from the foam pour. Each test sample shall be a rectangular prism with nominal dimensions of 1.0 inch thick (T) x 2.0 inches wide (W) x 2.0 inches long (L). The thickness dimension shall be the parallel-to-rise direction.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
: 3. Measure and record the thickness, width, and length of each test sample to an accuracy of +/-0.001 inches.
: 4. Compute and record the surface area of each test sample by multiplying the width by the length (i.e., W x L).
: 5. Place a test sample in a Universal Testing Machine. Lower the machines crosshead until it touches the test sample. Set the machines parameters for the thickness of the test sample.
: 6. Apply a compressive load to each test sample at a rate of 0.10 +/-0.05 inches/minute until a strain of 70%, or greater, is achieved. For each test sample, plot the compressive stress versus strain and record the compressive stress at strains of 10%, 40%, and 70%.
: 7. Determine and record the average parallel-to-rise compressive stress of the three test samples from each pour. As delineated in Table 8.1-1, the average parallel-to-rise compressive stress for each pour shall be the nominal compressive stress +/-20% at strains of 10%, 40%, and 70%.
: 8. Determine and record the average parallel-to-rise compressive stress of all test samples from each foamed component. As delineated in Table 8.1-1, the average parallel-to-rise compressive stress for a foamed component shall be the nominal compressive stress +/-15% at strains of 10%, 40%, and 70%.
8.1.4.1.2.3.3    Perpendicular-to-Rise Compressive Stress
: 1. Three (3) test samples shall be taken from the foam pour. Each test sample shall be a rectangular prism with nominal dimensions of 1.0 inch thick (T) x 2.0 inches wide (W) x 2.0 inches long (L). The thickness dimension shall be the perpendicular-to-rise direction.
: 2. Place the test samples in a room (ambient) temperature environment (i.e., 65 &#xba;F to 85 &#xba;F) for sufficient time to thermally stabilize the test samples. Measure and record the room temperature to an accuracy of +/-2 &#xba;F.
8.1-17
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
: 3. Measure and record the thickness, width, and length of each test sample to an accuracy of
    +/-0.001 inches.
: 4. Compute and record the surface area of each test sample by multiplying the width by the length (i.e., W x L).
: 5. Place a test sample in a Universal Testing Machine. Lower the machines crosshead until it touches the test sample. Set the machines parameters for the thickness of the test sample.
: 6. Apply a compressive load to each test sample at a rate of 0.10 +/-0.05 inches/minute until a strain of 70%, or greater, is achieved. For each test sample, plot the compressive stress versus strain and record the compressive stress at strains of 10%, 40%, and 70%.
: 7. Determine and record the average perpendicular-to-rise compressive stress of the three test samples from each pour. As delineated in Table 8.1-1, the average perpendicular-to-rise compressive stress for each pour shall be the nominal compressive stress +/-20% at strains of 10%, 40%, and 70%.
: 8. Determine and record the average perpendicular-to-rise compressive stress of all test samples from each foamed component. As delineated in Table 8.1-1, the average perpendicular-to-rise compressive stress for a foamed component shall be the nominal compressive stress
    +/-15% at strains of 10%, 40%, and 70%.
Table 8.1 Acceptable Compressive Stress Ranges for Foam (psi)
Parallel-to-Rise at Strain, //      Perpendicular-to-Rise at Strain, Sample Range          =10%        =40%        =70%      =10%      =40%        =70%
Nominal -20%            188          216          544        156          188          536 Nominal -15%            200          230          578        166          200          570 Nominal            235          270          680        195          235          670 Nominal +15%            270          311          782        224          270          771 Nominal +20%            282          324          816        234          282          804 8.1.5      Tests for Shielding Integrity The HalfPACT packaging does not contain any biological shielding. Poured lead shielding integrity for the SC-30G1, SC-30G2, SC-30G3, and SC-55G2 shielded container sidewalls shall be confirmed via gamma scanning or other nondestructive testing method suitable for that purpose (capable of producing volumetric results).
The acceptance criteria for the shielding integrity testing shall be able to confirm the minimum sidewall lead thickness per the applicable SAR drawing (163-008, 163-010, 163-011, and 163-013 for the SC-30G1, SC-30G2, SC-30G3, and SC-55G2, respectively).
With respect to the SC-30G2, SC-30G3, and SC-55G2, grid locations aligned with the payload cavity are scanned with the source axially aligned with the detector; the reject count rate (RCR)
(i.e., acceptance criterion) is based on a flat-block calibration measurement. The axial grid 8.1-18
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 locations for the straight-shot measurements are as follows: 1.5 - 30.0 for the SC 30G2 and SC-30G3, and 1.5 - 36.0 for the SC 55G2.
For axial grid locations below and above the SC-30G2, SC-30G3, and SC-55G2 payload cavities, however, the gamma scan procedure shall include measurements for shielding efficacy using the following steps:
: 1. Establish a source position above the bottom of the payload cavity that allows angled dose rate measurements beyond the payload cavity, including measuring for the presence of axial gaps in the sidewall lead. Figure 8.1-1, Figure 8.1-2, and Figure 8.1-3 for the SC-30G2, SC-30G3, and SC-55G2, respectively, show the detector in its lowest and highest grid positions for detecting the presence of axial gaps at the ends of the sidewall lead column.
The detector in the three figures is assumed to have a relatively standard, 2-inch diameter scintillator face.
: 2. Create shielding models of the prototypic gamma scan test configurations for the SC-30G2, SC-30G3, and SC-55G2 designs with minimum material conditions, i.e., minimum steel shell and sidewall lead thicknesses, including the presence of a 1/2-inch axial gap at both ends of the sidewall lead column. The models shall include a test base and test lid.
: 3. Run three shielding models for a unit source strength gamma source (e.g., 60Co or 192Ir) for a straight-through-the-wall baseline case, then for the slant-shot grid rows below and above the payload cavity. For example, with reference to Figure 8.1-1 for the SC-30G2, the below and above grid locations are -1.5, -3.0, 31.5, and 33.0. An RCR adjustment factor shall be applied to these slant-shot grid rows by calculating the ratio of the slant-shot unit dose rate with the straight-through unit dose rate for each grid row.
8.1-19
 
HalfPACT Safety Analysis Report                  Rev. 9, August 2022 Figure 8.1 SC-30G2 Gamma Scan Grid Layout Beyond the Payload Cavity 8.1-20
 
HalfPACT Safety Analysis Report                  Rev. 9, August 2022 Figure 8.1 SC-30G3 Gamma Scan Grid Layout Beyond the Payload Cavity 8.1-21
 
HalfPACT Safety Analysis Report                  Rev. 9, August 2022 Figure 8.1 SC-55G2 Gamma Scan Grid Layout Beyond the Payload Cavity 8.1-22
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 8.1.6    Thermal Acceptance Test Material properties utilized in Chapter 3.0, Thermal Evaluation, are consistently conservative for the normal conditions of transport (NCT) and hypothetical accident condition (HAC) thermal analyses performed. In addition, HAC fire certification testing of the HalfPACT package (see Appendix 2.10.3, Certification Tests) served to verify material performance in the HAC thermal environment. As such, with the exception of the tests required for polyurethane foam, as shown in Section 8.1.4, Component Tests, specific acceptance tests for material thermal properties are not performed.
8.1-23
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
8.1-24
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 8.2 Maintenance Program This section describes the maintenance program used to ensure continued performance of the HalfPACT package.
8.2.1 Structural and Pressure Tests 8.2.1.1      Pressure Testing Perform structural pressure testing on the inner containment vessel (ICV) and, optionally, the outer confinement vessel (OCV) per the requirements of Section 8.1.2.2, Pressure Testing, once every five years. Upon completing the structural pressure test, perform leakage rate testing on the ICV and, optionally, the OCV per the requirements of Section 8.1.3, Fabrication Leakage Rate Tests.
8.2.1.2      ICV Interior Surfaces Inspection Annual inspection shall be performed of the accessible interior surfaces of the ICV for evidence of chemically induced stress corrosion. After removal of the ICV spacer assemblies, perform a visual inspection for indications of ICV interior surface corrosion. Should evidence of corrosion exist, a liquid penetrant inspection of the ICV interior surfaces, including accessible shell, head, flange, and weld surfaces, shall be performed per ASME Boiler and Pressure Vessel Code, Section V 1, Article 6, and ASME Boiler and Pressure Vessel Code, Section III 2, Division 1, Subsection NB, Article NB-5000, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. Indications of cracking or distortion shall be recorded on a nonconformance report and dispositioned prior to corrective actions.
Once the packaging is put into service, at a maximum interval of five (5) years, an examination shall be performed on the accessible interior surfaces of the ICV for evidence of chemically induced stress corrosion. This examination shall consist of a liquid penetrant inspection of the entire ICV interior surfaces, including the accessible shell, head, flange, and weld surfaces, and shall be performed per ASME Boiler and Pressure Vessel Code, Section V, Article 6, and ASME Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NB, Article NB-5000, as delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings. Indications of cracking or distortion shall be recorded on a nonconformance report and dispositioned prior to corrective actions.
8.2.2 Maintenance/Periodic Leakage Rate Tests This section provides the generalized procedure for maintenance and periodic leakage rate testing of the vessel penetrations during routine maintenance, or at the time of seal replacement or seal 1
American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section V, Nondestructive Examination, 1995 Edition, 1997 Addenda, United Engineering Center, 345 East 47th Street, New York, NY.
2 American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Power Plant Components, 1995 Edition, 1997 Addenda, United Engineering Center, 345 East 47th Street, New York, NY.
8.2-1
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 area repair. Maintenance/periodic leakage rate testing shall follow the guidelines of Section 7.4, Maintenance Leakage Rate Test, and Section 7.5, Periodic Leakage Rate Test, of ANSI N14.5 3.
Maintenance/periodic leakage rate testing shall be performed on the main O-ring seal and vent port plug seal for the inner containment vessel (ICV) in accordance with Section 8.2.2.2, Helium Leakage Rate Testing the ICV Main O-ring Seal, and Section 8.2.2.3, Helium Leakage Rate Testing the ICV Outer Vent Port Plug O-ring Seal. Optional leakage rate testing of the outer confinement vessel (OCV) main O-ring seal and OCV vent port plug shall be performed in accordance with Section 8.1.3.6, Optional Helium Leakage Rate Testing the OCV Main O-ring Seal Integrity, and Section 8.1.3.7, Optional Helium Leakage Rate Testing the OCV Vent Port Plug O-ring Seal Integrity. Each leakage rate test shall meet the acceptance criteria delineated in Section 8.2.2.1, Maintenance/Periodic Leakage Rate Test Acceptance Criteria.
8.2.2.1      Maintenance/Periodic Leakage Rate Test Acceptance Criteria Maintenance/periodic leakage rate test acceptance criteria are identical to the criteria delineated in Section 8.1.3.1, Fabrication Leakage Rate Test Acceptance Criteria.
8.2.2.2      Helium Leakage Rate Testing the ICV Main O-ring Seal
: 1. The maintenance/periodic leakage rate test of the ICV main O-ring seal shall be performed following the guidelines of A.5.4, Evacuated Envelope - Gas Detector, of ANSI N14.5.
: 2. The ICV shall be assembled with both main O-ring seals installed into the ICV lower seal flange and the wiper O-ring installed into the holder. Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 3. Verify that the ICV vent port cover and ICV outer vent port plug have been removed. Verify that the ICV inner vent port plug is installed and tighten to 55 - 65 lb-in torque.
: 4. Connect a vacuum pump to the ICV vent port and evacuate the ICV vent port cavity to 90%
vacuum or better (i.e., 10% ambient atmospheric pressure). If the ICV vent port cavity cannot be evacuated to the required vacuum, remove the ICV lid and inspect the ICV wiper O-ring seal, the ICV upper main O-ring seal, and sealing surfaces for damage. Replace any damaged O-ring seals and repair any damaged sealing surfaces prior to re-performing the ICV main O-ring seal test.
: 5. Remove the ICV seal test port plug and install a helium mass spectrometer leak detector to the ICV seal test port. Evacuate the ICV seal test port cavity until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 6. Provide a helium atmosphere inside the ICV vent port cavity by backfilling with helium gas to a pressure slightly greater than atmospheric pressure (+1 psi, -0 psi).
: 7. Perform the helium leakage rate test to the requirements of Section 8.2.2.1, Maintenance/Periodic Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the ICV main O-ring seal fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating 3
ANSI N14.5-1997, American National Standard for Radioactive Materials - Leakage Tests on Packages for Shipment, American National Standards Institute, Inc. (ANSI).
8.2-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.2.2.3      Helium Leakage Rate Testing the ICV Outer Vent Port Plug O-ring Seal
: 1. The maintenance/periodic leakage rate test of the ICV outer vent port plug O-ring seal shall be performed following the guidelines of A.5.4, Evacuated Envelope - Gas Detector, of ANSI N14.5.
: 2. The ICV shall be assembled with both main O-ring seals installed into the ICV lower seal flange and the wiper O-ring installed into the holder. Assembly is as shown in Appendix 1.3.1, Packaging General Arrangement Drawings.
: 3. Verify that the ICV vent port cover and ICV outer vent port plug have been removed. Verify that the ICV inner vent port plug is installed and tighten to 55 - 65 lb-in torque.
: 4. Connect a vacuum pump to the ICV vent port and evacuate the ICV vent port cavity to 90%
vacuum or better (i.e., 10% ambient atmospheric pressure). If the ICV vent port cavity cannot be evacuated to the required vacuum, remove the ICV lid and inspect the ICV wiper O-ring seal, the ICV upper main O-ring seal, and sealing surfaces for damage. Replace any damaged O-ring seals and repair any damaged sealing surfaces prior to re-performing the ICV main O-ring seal test.
: 5. Provide a helium atmosphere inside the ICV vent port cavity by backfilling with helium gas to a pressure slightly greater than atmospheric pressure (+1 psi, -0 psi).
: 6. Install the ICV outer vent port plug and tighten to 55 - 65 lb-in torque.
: 7. Install a helium mass spectrometer leak detector to the ICV vent port. Evacuate the ICV vent port cavity until the vacuum is sufficient to operate the helium mass spectrometer leak detector.
: 8. Perform the helium leakage rate test to the requirements of Section 8.2.2.1, Maintenance/Periodic Leakage Rate Test Acceptance Criteria. If, after repeated attempts, the ICV outer vent port plug O-ring seal fails to pass the leakage rate test, isolate the leak path and, prior to repairing the leak path and repeating the leakage rate test, record on a nonconformance report and disposition prior to final acceptance in accordance with the cognizant quality assurance program.
8.2.3 Subsystems Maintenance 8.2.3.1      Fasteners All threaded components shall be inspected annually for deformed or stripped threads. Damaged components shall be repaired or replaced prior to further use. The threaded components to be visually inspected include the lock bolts, the OCV and ICV seal test port and vent port plugs, the OCV and ICV vent port covers, and OCV access plugs.
8.2.3.2      Locking Rings Before each use, inspect the OCV and ICV locking ring assemblies for restrained motion. Any motion-impairing components shall be corrected prior to further use.
8.2-3
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 8.2.3.3      Seal Areas and Grooves 8.2.3.3.1      Seal Area Routine Inspection and Repair Before each use and at the time of seal replacement, the ICV sealing surfaces shall be visually inspected for damage that could impair the sealing capabilities of the HalfPACT packaging.
Damage shall be corrected prior to further use (e.g., using emery cloth restore sealing surfaces) to the surface finish specified in Section 8.2.3.3.2.4, Surface Finish of Sealing Areas. The above delineated requirements may optionally be applied to the OCV.
Upon completion of ICV seal area repairs, verify depth of O-ring groove does not exceed the value in Section 8.2.3.3.2.5, O-ring Groove Depth, when repairs are in the O-ring groove; perform leakage rate test per the applicable section of Section 8.2.2, Maintenance/Periodic Leakage Rate Tests. The above delineated requirements may optionally be applied to the OCV.
8.2.3.3.2      Annual Seal Area Dimensional Inspection In order to demonstrate compliance of the ICV main O-ring seal regions, annual inspection of sealing area dimensions and surface finishes shall be performed as defined in Section 8.2.3.3.2.1, Groove Widths, through Section 8.2.3.3.2.5, O-ring Groove Depth. The above delineated requirements may optionally be applied to the OCV.
Allowable ICV measurements for these dimensions are based on a minimum O-ring compression of 10.73%, which will ensure leaktight seals are maintained (see calculation in Appendix 2.10.2, Elastomer O-ring Seal Performance Tests).
All ICV measurement results shall be recorded and retained as part of the overall inspection record for the HalfPACT package. ICV measurements not in compliance with the following dimensional requirements require repairs. Upon completion of ICV repairs, perform a maintenance/periodic leakage rate test per the applicable section of Section 8.2.2, Maintenance/Periodic Leakage Rate Tests. The above delineated requirements may optionally be applied to the OCV.
8.2.3.3.2.1      Groove Widths The method of measuring the ICV and, optionally, OCV upper (lid) seal flange groove width is illustrated in Figure 8.2-1. Remove the ICV debris shield to measure the ICV upper seal flange groove width. As an option, the lid may be inverted to facilitate the measurement process. The measuring equipment includes a &#xd8;0.560 +/-0.001 inch pin gauge of any convenient length, and a
&#xd8;0.250 +/-0.001 inch ball. With reference to Figure 8.2-1, the pin gauge is aligned parallel with the inner lip of the upper seal flange. Acceptability is based on the following conditions:
* Having contact at location - and a gap at location - is a NO-GO condition indicating that the upper seal flange groove width is acceptable.
* Having contact or a gap at location - and contact at location - is a GO condition indicating that the upper seal flange groove width is unacceptable.
The method of measuring the ICV and, optionally, OCV lower (body) seal flange groove width is illustrated in Figure 8.2-2. The measuring equipment includes a &#xd8;0.273 +/-0.001 inch pin gauge of any convenient length, and a &#xd8;0.250 +/-0.001 inch ball. With reference to Figure 8.2-2, the pin gauge is aligned parallel with the outer lip of the lower seal flange. Acceptability is based on the following conditions:
8.2-4
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022
* Having contact at location - and a gap at location - is a NO-GO condition indicating that the lower seal flange groove width is acceptable.
* Having contact or a gap at location - and contact at location - is a GO condition indicating that the lower seal flange groove width is unacceptable.
Groove width measurements shall be taken and recorded at six equally spaced locations around the circumference of the seal flanges.
8.2.3.3.2.2      Tab Widths The method of measuring the ICV and, optionally, OCV upper (lid) seal flange tab width is illustrated in Figure 8.2-3. As an option, the lid may be inverted to facilitate the measurement process. The measuring device is a tab width gauge of any convenient size, with a 0.234 +/-0.001 inch inside width x 0.428 +/-0.001 inch inside height x 0.375 +/-0.005 inch thickness. With reference to Figure 8.2-3, the tab width gauge is aligned parallel with the lowermost lip of the upper seal flange. Acceptability is based on the following conditions:
* Having contact at location - and a gap at location - is a NO-GO condition indicating that the upper seal flange tab width is acceptable.
* Having contact or a gap at location - and contact at location - is a GO condition indicating that the upper seal flange tab width is unacceptable.
The method of measuring the ICV and, optionally, OCV lower (body) seal flange tab width is illustrated in Figure 8.2-4. The measuring device is a 0.494 +/-0.001 inch inside width x 0.250
+/-0.001 inch inside height x 0.375 +/-0.005 inch thick tab width gauge of any convenient size. With reference to Figure 8.2-4, the tab width gauge is aligned parallel with the uppermost lip of the lower seal flange. Acceptability is based on the following conditions:
* Having contact at location - and a gap at location - is a NO-GO condition indicating that the lower seal flange tab width is acceptable.
* Having contact or a gap at location - and contact at location - is a GO condition indicating that the lower seal flange tab width is unacceptable.
Tab width measurements shall be taken and recorded at six equally spaced locations around the circumference of the seal flanges.
8.2.3.3.2.3      Axial Play Measurement of axial play shall be performed to ensure that O-ring compression is sufficient to maintain package configuration and performance to design criteria. Axial play is the maximum axial distance that a lid can move relative to a body. Because the seal flange sealing surfaces are tapered, any axial movement where the lid moves away from the body results in a separation of the sealing surfaces and a slight reduction in O-ring compression. The procedure for measuring ICV and, optionally, OCV axial play is as follows:
: 1. Remove the vent port access plug (OCV only), vent port thermal plug (OCV only), vent port cover, and vent port plug(s). Remove the ICV debris seal (ICV only).
: 2. Assemble the lid onto the body.
8.2-5
 
HalfPACT Safety Analysis Report                                                Rev. 9, August 2022
: 3. Locate a minimum of six equally spaced locations around the exterior circumference of the lid and body. At each location, place vertically aligned temporary reference marks on the lid and body.
: 4. Install a vacuum pump to the vent port and evacuate the vessel sufficiently to fully compress the upper seal flange to the lower seal flange.
: 5. At each location, scribe a horizontal mark that intersects both the lid and the body vertical marks.
: 6. Install a source of pressure to the vent port and pressurize the vessel sufficiently to fully separate the upper seal flange from the lower seal flange.
: 7. At each location, scribe a second horizontal mark that intersects either the lid or the body vertical mark (select either the lid or body mark as a base point).
: 8. Measure and record the difference between the initial and final horizontal marks at each location. The maximum acceptable axial play at any location is 0.153 inch.
: 9. Other measuring devices, such as dial indicators, digital calipers, etc., may be used in lieu of the reference marking method, provided that the axial play is measured at a minimum of six equally spaced locations.
8.2.3.3.2.4    Surface Finish of Sealing Areas The surface finish in the ICV main O-ring sealing regions shall be a 125 micro-inch finish, or better, to maintain package configuration and performance to design criteria. Perform ICV surface finish inspections for the bottom of the grooves on the lower seal flange and the mating sealing surfaces on the upper seal flange. If the ICV surface condition is determined to exceed 125 micro-inch, repair the surface per the requirements of Section 8.2.3.3.1, Seal Area Routine Inspection and Repair. The above delineated requirements may optionally be applied to the OCV.
8.2.3.3.2.5    O-ring Groove Depth Verify the ICV O-ring groove depth to be less than 0.253 inches at six equally spaced locations around the circumference of the seal flanges. The above delineated requirements may optionally be applied to the OCV.
8.2.4 Valves, Rupture Discs, and Gaskets 8.2.4.1    Valves The HalfPACT packaging does not contain any valves.
8.2.4.2    Rupture Discs The HalfPACT packaging does not contain any rupture discs.
8.2.4.3    Gaskets ICV containment boundary O-ring seals shall be replaced within the 12-month period prior to shipment or when damaged (whichever is sooner), per the size and material requirements delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
8.2-6
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 Following ICV containment O-ring seal replacement and prior to a loaded shipment, the new seals shall be leakage rate tested to the requirements of Section 8.2.2, Maintenance/Periodic Leakage Rate Tests. The above delineated requirements may optionally be applied to the OCV.
The ICV debris shield and wiper O-ring seal shall be replaced within the 12-month period prior to shipment or when damaged (whichever is sooner), per the size and material requirements delineated on the drawings in Appendix 1.3.1, Packaging General Arrangement Drawings.
8.2.5 Shielding The HalfPACT packaging does not contain any biological shielding. Other than tests required prior to first use, no shielding tests are necessary to ensure continued performance of the SC-30G1, SC-30G2, SC-30G3, and SC-55G2 shielded containers.
8.2.6 Thermal No thermal tests are necessary to ensure continued performance of the HalfPACT packaging.
8.2-7
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 8.2 Method of Measuring Upper Seal Flange Groove Widths 8.2-8
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 8.2 Method of Measuring Lower Seal Flange Groove Widths 8.2-9
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 8.2 Method of Measuring Upper Seal Flange Tab Widths 8.2-10
 
HalfPACT Safety Analysis Report                      Rev. 9, August 2022 Figure 8.2 Method of Measuring Lower Seal Flange Tab Widths 8.2-11
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
8.2-12
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 9.0 QUALITY ASSURANCE This section describes the quality assurance (QA) requirements and methods of compliance applicable to the HalfPACT package.
9.1 Introduction The HalfPACT package is designed and shall be built for the U.S. Department of Energy (DOE),
and must be approved by the U.S. Nuclear Regulatory Commission (NRC) for the shipment of radioactive material in accordance with the applicable provisions of the U.S. Department of Transportation, described in Subpart I of 49 CFR Part 173 1. Procurement, design, fabrication, assembly, testing, maintenance, repair, modification, and use of the HalfPACT package are all done under QA programs that meet all applicable NRC and DOE QA requirements. QA requirements for payloads to be transported in the HalfPACT package are discussed in the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) 2.
1 Title 49, Code of Federal Regulations, Part 173 (49 CFR 173), Shippers-General Requirements for Shipments and Packagings, Current Version.
2 U.S. Department of Energy (DOE), Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC), U.S. Department of Energy, Carlsbad Field Office, Carlsbad, New Mexico.
9.1-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
9.1-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 9.2 Quality Assurance Requirements 9.2.1 U.S. Nuclear Regulatory Commission The QA requirements for packaging established by the NRC are described in Subpart H of 10 CFR 71 1. Subpart H is an 18 criteria QA program based on ANSI/ASME NQA-1 2.
Guidance for QA programs for packaging is provided in NRC Regulatory Guide 7.10 3.
9.2.2 U.S. Department of Energy The QA requirements of DOE for the use of NRC certified packaging are described in Chapter 4 of DOE Order 460.1D 4. The DOE and its contractors may use NRC certified Type B packaging only under the conditions specified in the certificate of compliance.
9.2.3 Transportation to or from WIPP Public Law 102-579, enacted by the 102nd Congress, reads as follows:
SEC. 16. TRANSPORTATION.
(a) SHIPPING CONTAINERS. - No transuranic waste may be transported by or for the Secretary [of Energy] to or from WIPP, except in packages -
(1) the design of which has been certified by the Nuclear Regulatory Commission; and (2) that have been determined by the Nuclear Regulatory Commission to satisfy its quality assurance requirements.
The determination under paragraph (2) shall not be subject to rulemaking or judicial review.
1 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
2 ANSI/ASME NQA-1, Quality Assurance Requirements of Nuclear Power Plants, American National Standards Institute.
3 U.S. Nuclear Regulatory Commission, Regulatory Guide 7.10, Establishing Quality Assurance Programs for Packaging Used in the Transport of Radioactive Material, Revision 3, June 2015.
4 U.S. Department of Energy Order 460.1D, Hazardous Materials Packaging and Transportation Safety, December 2016.
9.2-1
 
HalfPACT Safety Analysis Report                              Rev. 9, August 2022 This page intentionally left blank.
9.2-2
 
HalfPACT Safety Analysis Report                                                      Rev. 9, August 2022 9.3 Quality Assurance Program 9.3.1 NRC Regulatory Guide 7.10 Guidance for QA programs applicable to design, fabrication, assembly, testing, maintenance, repair, modification, and use of packaging used in transport of radioactive material is covered in NRC Regulatory Guide 7.10 1.
9.3.2 Design The HalfPACT package was designed under a QA program approved by the NRC for packaging design. Requests for modification or changes to the design will be submitted to the NRC for approval prior to modification of the HalfPACT packaging. Any future design changes shall be made under an appropriate QA program that has been verified to satisfy 10 CFR 71, Subpart H 2.
9.3.3 Fabrication, Assembly, Testing, and Modification Fabrication, assembly, testing, and modification of each HalfPACT packaging are performed under a QA program verified to satisfy 10 CFR 71, Subpart H2 and approved for these activities.
9.3.4 Use The HalfPACT package will be used primarily by the DOE for shipments of authorized contents to the WIPP site. However, it may also be used between DOE sites other than WIPP (inter-site), and for DOE on-site shipments within site boundaries (intra-site). The DOE is registered with the NRC as a user of the HalfPACT package under the general license provisions of 49 CFR
&sect;173.471 3. The HalfPACT package may also be used for non-DOE shipments as authorized by the NRC.
9.3.4.1      DOE Shipments: To/From WIPP Use of the HalfPACT packaging for shipments to/from the WIPP site shall be made under a QA program that meets the QA requirements of the NRC. The appropriate DOE Field Office(s) shall evaluate and approve the QA programs of the DOE contractors that make shipments to/from WIPP in the HalfPACT package. DOE or the DOE managing and operating contractor for the WIPP shall perform surveillances of the HalfPACT package users QA programs to ensure that the package is used in accordance with the requirements of the certificate of compliance.
9.3.4.2      Other DOE Shipments: Non-WIPP The appropriate DOE Field Office(s) shall evaluate and approve the shippers and receivers QA programs for equivalency to the NRCs QA program requirements in Subpart H of 10 CFR 712.
1 U.S. Nuclear Regulatory Commission, Regulatory Guide 7.10, Establishing Quality Assurance Programs for Packaging Used in the Transport of Radioactive Material, Revision 3, June 2015.
2 Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packaging and Transportation of Radioactive Material, 01-01-19 Edition.
3 Title 49, Code of Federal Regulations, Part 173 (49 CFR 173), Shippers-General Requirements for Shipments and Packagings, Current Version.
9.3-1
 
HalfPACT Safety Analysis Report                                              Rev. 9, August 2022 For example, a contractor working under an 18 criteria QA program per ANSI/ASME NQA-1 4 could be deemed acceptable if the portion of the program applicable to packaging is found compliant with 10 CFR 71, Subpart H2. DOE or the DOE managing and operating contractor for the WIPP shall perform surveillances of the HalfPACT package users QA programs to ensure that the package is used in accordance with the requirements of the Certificate of Compliance.
9.3.4.3    Non-DOE Users of HalfPACT Non-DOE users of the HalfPACT package shall have QA programs verified to satisfy 10 CFR 71, Subpart H2.
9.3.5 Maintenance and Repair Minor maintenance, such as changing seals or fasteners, may be performed under the users QA program. Major maintenance, such as cutting or welding a containment boundary, shall be performed under an appropriate QA program that has been verified to satisfy 10 CFR 71, Subpart H2.
4 ANSI/ASME NQA-1, Quality Assurance Requirements of Nuclear Power Plants, American National Standards Institute.
9.3-2}}

Latest revision as of 00:40, 16 November 2024

Redacted - August 2022, Revision No. 9 of the Safety Analysis Report for the Model No. Halfpact Package (Docket No. 71-9279)
ML22319A229
Person / Time
Site: 07109218, 07109279
Issue date: 08/18/2022
From: Sellmer T
Nuclear Waste Partnership
To:
Division of Fuel Management
Garcia-Santos N
Shared Package
ML22319A224 List:
References
001029, L-2022-LLA-0123, L-2022-LLA-0122
Download: ML22319A229 (555)
v • d • e


Text

Retrieved from "https://kanterella.com/w/index.php?title=ML22319A229&oldid=3717617"